Search Documents

By Paul J. Remington

The field data gathered as part of the measurements described in Volumes I and II were re-analyzed in the low frequency regime (.1 Hz to 1 Hz) where motion sickness normally occurs. These data were compared co the international standard ?ISO 2631 Addendum 2: Evaluation of exposure to whole body z-axis vertical vibration in the frequency range 0.1 to 1.0 Hz." For both underground mining machines and surface mining machines the results showed that one would not expect motion sickness to .be a severe problem. New field data were gathered on the vibration reduction performance of various seat designs found on surface coal mining machines. The vibration during normal operation was measured on the seat using the standard seat pad accelerometer package described in the previous two volumes and simultaneously on the floor of the machine at the base of the seat. Preliminary indications are that the so-called high performance seats used for operator vibration reduction do not offer significant improvement over conventional seats.

Jan 1, 1984

This is the third in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C. F. R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-36.3/ The second report gave the same data for motor gasolines sold during the summer of 1936)4/ As was the case with the first cooperative gasoline survey, reports were received for some areas from only one company and in other areas from two companies that did not in all instances report on the same brands of gasoline. In still other areas reports were received from five or six companies on the same brands of gasoline. Thus, it can be seen that data on gasolines are unequal in regard, to the number of reports that were averaged in calculating the data shown in table 1. The data from the Pacific Coast were averaged by the Pacific Coast technical group before submission and are published exactly as they were submitted.

Jan 1, 1937

By Alfred Wild

The Kraftile Co. plant, Fremont, Alameda County, Calif.--the largest producer of glazed, structural wall units west of the Rocky Mountains--maintains modern processing facilities to evaluate and blend a wide variety of clays from several sources to produce quality products. The report desribes the prospecting, exploration, and test methods used to locate raw material sources and covers processing methods, cost factors, and trends. Also, the geologic and ceramic factors are considered in a general discussion of the economics, potentials, and requirements of clays as raw materials for ceramic tile manufacturing.

Jan 1, 1963

By H. S. Hardman, G. T. Adams, Will H. Goghill

"Usually a newly developed machine leaves the factory ""on a wing and a prayer."" The manufacturer hopes that the operator will hasten to report defects. In turn, when the suggestions arrive the manufacturer makes the required changes and maintains close collaboration with the operator. Thus the history of our machines of today is written.Laboratory concentration tables are exceptions to growth by experiment and collaboration. Their operation never enters directly into the cost sheet; they are seldom used for longer periods than 10 minutes; and the experimenter, while hurrying to another job, accepts the table, good or bad, for a quick test on his ore. Thus we go back about 50 years when we use the preset in factory-built laboratory table.The Southern Experiment Station, Bureau of Mines, in cooperation with the University of Alabama, recognized the existence of a tabling problem net usually considered. That is, instead of using the table to test the ore, the ore was used to test the table. In this critical examination of laboratory table six defects were encountered (and remedied). They are:"

Oct 1, 1945

By Ben E. Lindsly

The study of "bottom-hole' samples follow,-is in natural sequence the study of samples3 obtained under high pressures at the well heads of flowing wells. The principal object of this phase of gas-solubility research, started actively in January, 1530, was to gain a more accurate knowledge of the physical and chemical characteristics of the oil-gas mixtures that exist in natural reservoirs. In possession of actual data regarding the condition of the oil; the quantity of gas liberated from solution upon dimunition of pressure; and the relative volumetric proportions of gas to oil at various pressures throughout the flow string in a well, it should be possible to predict, with a fair degree of accuracy, what physical changes these mixtures would undergo throughout the life of a pool. Such information not only is important in designing flow strings in flowing wells but is important also in solving problems relating to pumping efficiency and the power required for pumping. Although certain fundamental rata Mere obtained in the stud of samples taken at the well head, "bottom-hole" samples are more representative of subsurface mixtures of oil and gas because they are obtained at reservoir temperatures, and before the oil has had the opportunity of intermingling with extraneous gas; that is, gas which either was not in solution originally, or which was liberated from solution at some higher pressure, and later became mired with the original undissolved gas.

Jan 1, 1933

By Jos. R. Guiteras

This paper describes the pumping operations at the Ajax, Cresson, and Vindicator dines in the Cripple Creek mining district of Colorado during the summer of 1936. At that time the three mines wore pumping 6,500 gallons of water per minute into the Roosevelt drainage tunnel. Cripple Creek is the most important gold district in the State; it has yielded gold valued at over $365,000,000. The mines engaged in pumping are among the largest producing properties in the district. ACKNOWLEDGMENTS The author wishes to acknowledge the friendly cooperation of mine officials at the properties visited. At the. Ajax mine information was courteously given by Clayton Kissel, mine superintendent, and his staff; R. Y. Roby contributed the drawings. For information on the Cresson mine, thanks are expressed to Al H. Bebee, mine superintendent, and his staff, especially to Guy Rorabaugh, master mechanic, and to engineer Carlton. At the Vindicator mine, J. S. Anderson; mine superintendent, and Robert Welch, master mechanic, assisted; the latter furnished most of the information about that mine. Acknowledgment is also made of the cooperation of M. H. Salsbury, engineer at the Portland mine, who supplied technical data on the Roosevelt drainage tunnel.

Jan 1, 1937

In 2007, a total of 4,639 stone mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 Stone mines comprised 31.2% of all mining operations. ? Mines producing the primary commodity of limestone (crushed and broken) comprised the largest number of operations (n=2,051; 44.2%). ? Stone mining operations were located in all states and territories except Delaware and North Dakota. ? Pennsylvania had the most stone mines (n=373; 8.0%), followed by Texas (n=352; 7.6%).

Aug 1, 2009

By Peter F. R. Altounyan, Paul B. Cartwright, John W. Cassie

This paper describes measured data on strata behavior obtained in recent years from sites in the United Kingdom and the implications for pillar design. The data include results from overcoring stress measurements adjacent to coal mine roadways and deformation monitoring related to longwall extraction. The stresses adjacent to mine roadways or entries have been measured at a number of coal mine sites in the United Kingdom. The results are analyzed with regard to the information they provide on pillar behavior and strength estimates. A reduction in stress consistent with yielding of the strata adjacent to the roadways is evident. This is consistent with the confined core model for pillar behavior. The pillar strength is dependent on the rate atwhich vertical stress can increase with distance from the pillar edge and hence the confinement provided to the yielded material. The measured data indicate a wide range in pillar strengths. Two groups of results are identified that show significantly different behavior corresponding to differing effective pillar strengths. Estimates of pillar strengths derived from the measured data for these two groups are compared with established equations used for pillar design. The differing behaviors and strengths are attributed to variations in the amount of yielding and deformation in roof and floor strata and hence in the amount of confinement they provide to the coal seam. Numerical modeling is used to provide a comparison with the measured data and to indicate that this provides a feasible mechanism to account for the measured data. As the depth of mining increases, pillars tend to become increasingly wide and squat. In such cases, it is possible for the surrounding roadways to become badly deformed and damaged while the pillars remain stable. The criteria of comparing pillar strengths and loads to establish pillar stability become less applicable in these circumstances; rather, considerations of roadway stability may be the limiting factor in determining suitable pillar dimensions. This is the case for pillar dimensions typically employed around longwall panels in the United Kingdom. Depending on the properties of the site and what are deemed to be satisfactory roadway conditions, this can lead to wide variations in required pillar dimensions. Measured data for deformations in roadways influenced by adjoining longwall workings are presented. These show that in some circumstances the influence of longwall extraction can be transmitted over large distances and confirm the variability in required pillar sizes depending on site properties.

Jan 5, 1999

By Paul M. Tyler

Graphite occurs in many places in the United States, but previous to 1914 the domestic production amounted to only 15 to 20 per cent of the natural graphite consumed in this country. Including artificial, graphite, the proportion was about 25 per cent. During the World War the production of both natural and artificial graphite increased until, in 1918 it, contributed more than one-half of the available supply, and since 1919 the proportion has not fallen below 40 per cent. Except during the war period, however, this apparently increasing independence has not been due to any large increase in production from domestic mines. It simply reflects a larger output of artificial graphite and reduced imports of Ceylon lung and chip, grades which have never been produced in substantial quantity in the United States. DOMESTIC DEPOSITS3 American graphite deposits, though numerous and often large, are characteristically low-grade. They constitute an abundant source of potential supply, but in normal times they have proved relatively costly to work, and even at the same price the various products have never been able wholly to displace certain imported qualities, notably crucible grades from Ceylon and pencil graphite from Mexico.

Jan 1, 1929

By R. F. Waters

Laboratory-scale selective volatilization methods developed by the Bureau of Mines to recover germanium and gallium concentrates from coal fly ash and phosphorus furnace flue dust are summarized. In the better experiments between 85 and 98 percent of the germanium was recovered as the lower oxide and as sulfides, and between 75 and 97 percent of the gallium was recovered as the lower oxide and as the trichloride. Grades of the condensates were inconsistent and varied between a few tenths of a percent and 8 percent, depending on the method used. In the primary extractions of germanium alone the degree of enrichment surpassed 100 to 1, and for gallium the best ratio was 30 to 1. Upgrading of condensates by vaporization retreatment and by leaching and precipitation is discussed. An appreciable degree of mechanical preconcentration by attrition scrubbing and elutriation was possible on two fly ash samples.

Jan 1, 1967

By Alan G. Mayton

A prototype end-cab shuttle car (SC) design has been developed to improve protection and address ergonomic concerns of the SC operator in low coal mines. The new design features an end cab transversely mounted to the SC and equipped with a closed-circuit video system. The end cab was retrofitted to a low-coal SC and evaluated in surface trials at the U.S. Bureau of Mines. During surface trials, test operators evaluated the end-cab SC relative to visibility; cab features-space, seating, controls, and operator position; tramming-inby, outby, and turning corners; and dumping. Trials were conducted using 12 test subjects; 6 were experienced SC operators. Results of the trials were promising. Of the experienced operators, the only operator with low-coal experience gave the new design the highest rating. Four experienced operators rated the end-cab design "better" to "much better" than a standard center-driven, side-cab SC for visibility when tramming, protection from roof and rib hazards, and no change in seat position with direction of travel. This report discusses research to modify a used 21SC JOY SC, retrofit the SC with the Bureau-developed end-cab, and evaluate the retrofitted end-cab SC in surface trials.

Jan 1, 1993

By A. C. Johnson

This paper is one of a series being prepared by the Bureau of Mines on exploration, development, mining methods and costs at various mines in the United States. It describes such methods at the Lincoln tungsten mine of the Wah Chang Mining Corp., Lincoln County, Nev. The purpose of these reports is to promote development and conservation of our mineral resources by disseminating technologic information on mining methods, practices and costs. The Lincoln mine in Lincoln County, Nev., in the southeastern part of the [tate], was acquired by the Wah Chang Mining Corp., in April 1951. Mining methods and costs are of special interest at this property because of the low costs and good production record achieved through a well planned program of exploration, development, and exploitation. Operations were discontinued in July 1957 after the Federal Government suspended the tungsten purchase program.

Jan 1, 1959

By W. E. Miller, John Campbell, W. P. Yant, G. W. Jones

"Because of its interest in accident prevention, the U.S. Bureau of Mines cooperates with city officials and utilities in investigating the causes of explosions in sewers, manholes, and other underground openings and in developing means for preventing such explosions. For several years this Bureau has been cooperating with the Edison Electric Illuminating Co. of Boston and the Boston Consolidated Gas Co. in detecting and eliminating combustibles and physiologically harmful gases in manholes in the city of Boston and adjacent territory.These Bureau of Mines investigations° have shown that combustible gases from the usual sources — leakage from gas—distributing systems and from underground tanks and gasoline wastes — can be located and the dangerous conditions remedied by a well—planned, adequately supervised, systematic, and continuous manhole survey. However, other types of gas, which are termed here ""soil"" gases, also occur in manholes and are more difficult to eliminate because they have no fixed origin and because seasonal and barometric changes affect their production and passage into the manhole space. These gases appear to be produced by bacterial and fermentation or through reactions of entrapped air in the soil. Soil usually abnormally high in carbon dioxide and low in oxygen, and contain varying amounts of methane. They are especially clangorous to men entering manholes because they lack sufficient oxygen to support life. Owing to the difficulty of constructing gastight manholes the most feasible method for eliminating soil gases from manholes is by ventilation. Consequently the Bureau of Mines initiate 4 study of natural ventilation methods for the removal of these gases from manholes and also for taking care of unforeseen accumulations of combustible gases and vapors.The following factors were considered by the Bureau to be important to the natural ventilation of manholes: (1) Relation of area of ventilation opening* to the capacity of the manholes, (2) size and shape of the manhole, (3) design of the ventilation opening (4) and velocity, and (5) weather conditions."

Jun 1, 1936

By B. J. Scheiner

Silver ores from the Candelaria District, Nevada, and Round Mountain District, Colorado, were investigated mineralogically and metallurgically. Silver minerals of four distinct groups were identified: (1) silver sulfide; (2) argentojarosite; (3) silver contained in the iron oxide; and (4) manganese carbonate-oxide minerals, Electrooxidation and acid-chloride leaching techniques were investigated as means of altering silver minerals, and their effects on subsequent silver extraction were determined. Application of the knowledge obtained from mineral leaching studies resulted in development of a sulfur dioxide-sodium chloride leaching sequence for extracting silver from these types of ores. Silver extractions of 80 to 85 percent were obtained by leaching the ores with a sulfurous acid-sodium chloride system. This was an increase of 9 to 61 percent silver extraction over that obtained by conventional cyanidation techniques.

Jan 1, 1973

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

D.2 Principal Types of Coating A Sodium Silicate Sodium silicate is a good fire retarder when freshly applied, but it loses its effectiveness if the relative humidity is at all high, thus exposure to a relative humidity exceeding 65 percent causes a serious decrease in the effectiveness after only one month. In fire, sodium silicate swells to a frothy mass (intumescence) which hardens and insulates the wood against heat. This property is destroyed by exposure to moisture. Manufacturers of many of the proprietary paints containing silicates state that their products have overcome this difficulty The reagent may be applied alone, or, better, in a mixture with lime-water and common salt, or with inert fillers such as kaolin or asbestos. B Ammonium Phosphate Strong solutions (25 to 35 percent) of monammonium phosphate or diammonium phosphate give good protection. Two or three coats of hot solution should be applied either with a large flat brush or an ordinary paint spray gun The solution should be applied as hot as possible, as this improved penetration, and it should be the aim of the operator to apply 4 lbs of reagent, i e , one gallon of 33 percent solution to every 100 square feet of surface

Jan 1, 1976

By Frank D. McGuirk

Underground coal mining is traditionally hazardous. Although many danger-prone human activities are now performed by mechanized equipment, this mechanization has itself brought new dangers to the underground mining industry, and the loss of life and limb has caused increased concern for mine safety. The 1969 Federal Coal Mine Health and Safety Act has precipitated a great deal of safety-related research on the part of the Government, industry, and private agencies. Much of this safety research has been focused on the new and varied man-machine interfaces caused by increased mechanization. Recent projects in this area have dealt with standardized controls, emergency shutdown capabilities (panic bars, strike plates, self-centering controls, "dead man" controls), and machine operator protective devices (fully enclosed cabs, canopies, side rails). There was a need for integration of the findings of current and past projects to move rapidly toward the smooth, orderly implementation of standardized operator work station designs for underground mining equipment.

Jan 1, 1975

By R. P. Maloney

Since mining operations began in 1900, Government geologists and mining men have periodically recorded the presence of the minerals of mercury and antimony in the extensive gold placer deposits near Flat in the Iditarod district of the Yukon River region, Alaska. No serious effort was made to recover the cinnabar contained in the gold placer gravels, and there is no evidence that veins of cinnabar and stibnite exposed in the placer operations (as reported by the Geological Survey) were ever explored or developed. A large monzonitic intrusive, which is the dominant geologic feature of the immediate area, is believed to be the lode source of the valuable minerals in the placer deposits. In contact with the monzonite are argillite and quartzite, metamorphic products from the Cretaceous shales and sandstones.

Jan 1, 1962

By H. E. Powell

A laboratory investigation was conducted by the Bureau of Mines to study the magnetic characteristics and to measure the magnetic susceptibility of the mineral siderite. All susceptibility measurements were made by the method of Gouy on powdered samples and at room temperature. Specific susceptibilities of samples from 15 different locations, domestic and foreign, were determined. Values ranged from 66 to 103 (10-6) cgs electromagnetic units. The relation of susceptibility to mineral composition is discussed in this report. The specific susceptibilities of 76 minerals are tabulated in an appendix.

Jan 1, 1963

This Bureau of Mines publication presents an overview of mine electrical power systems research currently being conducted by the Bureau. The papers, given at a Technology Transfer Seminar, emphasize the increasing importance of research related to the safety considerations of underground coal mine electrical systems. Selected topics are included that summarize results of research in the areas of electrical shock prevention, explosion-proof enclosures and load centers, discriminating circuit breakers, and trailing cables. Other topics discussed at the seminar are published as separate sections of the Bureau of Mines Hand- book "Application Notes--Mine Electrical Power Systems."

Jan 1, 1982

By B. J. Barfield

Standard erosion plots (4.6 m by 22.1 m on 9 percent slope) were constructed on the Alston Surface Mine of Peabody Coal Company in Western Kentucky to evaluate the effects of placement technique and density on the erodibility and eroded size distribution from mine spoil and reconstructed topsoil. PLots were constructed with a dozer and scraper pan from shale spoil material, topsoil (A horizon) and subsoil (B and C horizon mixture) using soils stockpiled at the Alston Surface Mine. Plots were evaluated under fallow conditions with a tilled plot surface and two compacted conditions. One compacted condition was generated by tracking the surface with a dozer and rolling with a loaded scraper pan. The second was generated by rolling the surface with a solid wheel compactor. Rainfall was supplied with the Kentucky Rainfall Simulator at a rate of 63.5 mm h-l with the plots in three different soil moisture conditions; dry, field capacity, and very wet. Runoff was evaluated for flow rates, sediment concentrations, and aggregate and primary particle size distributions. Sediment yields and the Universal Soil Loss Equation E130 indexes were calculated from the data for each plot. The erodibility was calculated from the tilled plot data using a weighted soil loss and E130 value from the dry, field capacity and wet runs, and a cover management factor calculated for every other condition. For the topsoil and subsoil plots, sediment yield was greatest for the dozer scraper pan plots and lowest for the tilled plots. For the shale plots, erosion rates from the wheeled compacter plots were the highest and tilled plots the lowest. Average erodibilities were 0.14, 0.38, and 0.41 tons ac h ft-1 tonf-1 in-1 hundred ac-1 for the shale, subsoil, and top-soil plots. Cover management factors for each plot were 1.29, 1.42, and 1.17 for shale, topsoil and subsoil plots compacted with the solid wheeled compacter and 1.29, 3.79, and 2.51 for shale, subsoil, and topsoil plots compacted with the dozer scraper pan conbination. The accuracy of the Wischmeier erodibility nomograph was evaluated on the data collected. Erodibilities were accurately predicted for the topsoil plot and poorly predicted for the sub-soil plot. The accuracy of the CREAMS procedures for predicting the composition (size distribution) of eroded particles was also evaluated. The composition was well predicted for the topsoil plots, moderately well predicted for the shale plots and poorly predicted for the subsoil plots.

Jan 1, 1983