Search Documents

By W. S. Landers

This bulletin is a detailed study of low-temperature, entrained-bed carbonization of a Texas lignite. The lignite studied was from the Sandow strip mine and is representative of the Rockdale formation of the Wilcox formational group. Carbonization was conducted in a continuous entrained-bed reactor at several temperatures in the 8801 to 1,52°C F range, and at air-coal ratios it the 0 to 10.30 scf/lb range (moisture- and ash-free basis). Carbonization rates ranged from 97.1 to 410.0 lb/hr (as-received basis), At the higher air-to-coal ratios employed, all or most of the carbonization heat was provided by internal combustion with air in the reactor. At the lower air-to-coal ratios, parts of the heat for carbonization was supplied externally. It was demonstrated that the entrained-bed carbonization of lignite is a complex reaction and that several variables, of which carbonization temperature, air-to-lignite ratio, and the average size of lignite are important, act together to influence both the carbonization yields and the properties of the resultant products, Process variables established by pant tests were used to design the industrial scale carbonizer operated at Rockdale, Texas, by the Texas Power & Light Company as agents for the Aluminum Company of America. Properties of the carbonization product obtained from the industrial scale reactor were essentially the same as those obtained from the pilot plant reactor operated under the same conditions.

Jan 1, 1968

By T. G. Carnahan

In-place leaching is being actively utilized to extract uranium, copper, and evaporites from low-grade and difficult-to-mine ores. The purpose of this report is to discuss in-place leaching technology, its advantages and disadvantages, and to give an overview of past, current, and envisioned in-place leaching operations in the U.S.A. Application of in-place leaching to uranium ores has been particularly successful because the conditions for leaching are nearly ideal. The ores are generally in highly permeable sandstone aquifers bounded above and below by impermeable shales. The uranium ore minerals are easily leached with oxidizing acid or base solution and the pregnant solutions are amenable to ion exchange concentration and purification prior to conventional solution neutralization for recovery of yellow cake. Copper is routinely recovered from sub-grade rock by dump leaching at most major copper mines. Acidified ferric sulfate is either sprayed on the surface of the dumps or is ponded on top of the dumps. The leaching solution migrates down through the rock and dissolves copper. The solution is collected from the base of the dumps and copper is recovered by solvent extraction-electrowinning or by cementation on detinned steel cans. True in-place copper leaching is being practiced in the caved stopes of an exhausted underground copper mine. Other innovative in-place copper leaching techniques have been tested commercially and laboratory- and pilot-scale experiments have been conducted to investigate proposed in-place leaching techniques for extracting copper from difficult-to-treat chalcopyrite ores. Solution mining of evaporites is being conducted commercially for the extraction of sodium chloride and potassium chloride. A large-scale experimental project for solution mining of trona has been undertaken.

Jan 1, 1982

By Charles G. Patmon

This paper describing the methods of dredging and treatment of gold-bearing gravels at the Lancha Plana Gold Dredging Co.'s dredge is one of a series of similar papers being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The dredge is located near the Mokelumne River, 12 miles west of San Adreas, Calif.; it is accessible by an improved dirt road from Jackson, which is about 20 miles distant.

Jan 1, 1932

By A. R. T. Denues

The Explosives Division of the Bureau of Mines, United States Department of the Interior, is investigating cushioned blasting at the Explosives Testing Station, Bruceton, Pa. The general interests of this investigation are practical and relate particularly to safety. The immediate concern is an application of cushioned blasting in coal mining In cushioned blasting, various means are employed to reduce the intensity of the application of energy in an explosive action in a borehole. The primary object is to increase the efficiency of the use of explosives.

Jan 1, 1940

The Bureau of Mines analyzed the cycle of secondary gold to determine the quantity of gold not being recovered from scrap, and to identify areas for research to increase the supply of gold from scrap. Secondary gold in 1967 was estimated to be 2.4 million troy ounces; this excludes secondary gold which is recycled within consuming plants. Firms contacted included consumers using about 41 percent of the gold in 1967, And refiners that recovered about 90 percent of the secondary gold. Results of the study indicate that loss of gold is small, and refiners and consumers are accelerating programs designed to reduce recovery costs. With the increasing generation of low-grade industrial scrap, research is needed to improve present recovery techniques and to develop methods to accelerate the flow of secondary gold back to supply.

Jan 1, 1970

By Roy T. Sorensen

As part of its mission to maintain an adequate supply of minerals to meet national needs and maximize mineral production from domestic sources, the Bureau of Mines is investigating the recovery of alumina by hydrochloric acid leaching of kaolinitic clay. Most iron impurities are leached from the clay along with the alumina and must be removed before or during crystallization to aluminum chloride hexahydrate. The thermal decomposition step then provides an alumina product of acceptable iron analysis. Miniplant studies of a Bureau-developed solvent extraction technique, using a tertiary amine in kerosene diluent, have demonstrated that the iron content in aluminum chloride leach liquors can be reduced to levels of less than 0.007 wt-pct (7 ppm), expressed as Fe203. Entrained and dissolved organic matter in the purified pregnant leach liquor from the solvent extraction circuit can be reduced to less than 2 ppm by using a fabric-packed coalescer and subsequent activated carbon treatment. Investigators discovered that a steady buildup of zinc accumulated in the solvent phase within the extraction circuit, proportional to the amount of leach liquor treated. The solvent phase zinc analysis increased by 0.01 wt-pct ZnO for each 1,000 gal of pregnant leach liquor purified.

Jan 1, 1981

By G. L. Oldright

The past reputation of zinc as an ingredient in lead blast furnace slags has been bad. Zinc is thought of as a cause of accretions in the shaft of the blast furnace, of hot tops, of the formation of "zinc mush" in the crucible and forehearth, of leach rich slags, of viscous slags, and of low capacity in smelting.

Jan 1, 1934

This chapter summarizes data on crude mineral production for the United States, its island possessions, and the Common- wealth of Puerto Rico. Included also are tables that show the principal mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables 'were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the production of auxiliary processing at or near the mines.

Jan 1, 1978

By J. F. Messerly

The purity of three specially prepared samples of benzene was determined with an adiabatic, low-temperature calorimeter with automatic control of shield temperature. Extensive measurements were made on each sample to determine how variations in operating procedures affect melting-point and freezing-point as well as purity data obtained by the calorimetric method. Detailed results of the investigations are presented, and effects of different operating procedures are discussed, together with problems encountered in interpretating experimental results.

Jan 1, 1963

By R. V. Ramani

This volume, the first of a six volume final report, provides an executive summary of the research and results carried out under a grant from the U. S. Bureau of Mines on underground coal mine ventilation. Under the project, a mine ventilation simulator was developed. Sensitivity of leakage and friction factors on the total quantity and pressure requirements was studied. The simulator was applied to a new mine under development, and to an operating mine, to demonstrate the usefulness of the simulator in ventilation planning and in evaluating proposed changes to existing ventilation system. The titles of the other volumes are as follows: Volume II: Mine Ventilation Network Theory Volume III: User's Manual for PSU/MVS Volume IV: Sensitivity of Leakage and Friction Factors Volume V: Application of PSU/MVS to Ventilation Planning of a New Mine Volume VI: Application of PSU/MVS to the Analysis of Modifications to Existing Ventilation Systems

Jan 1, 1977

By M. Dattilo

The U.S. Bureau of Mines has been conducting research on the use of waste-derived zinc as a partial replacement for pure zinc in the electrogalvanizing process. The end product of this process is automotive sheet, which has enhanced cosmetic protection over previously used cold-rolled (CR) steel. In this study, primer-coated specimens of CR and electrogalvanized (EG) steel were subjected to the on-vehicle environment and monitored periodically by electrochemical impedance spectroscopy (EIS) during immersion in 1M NaCI solution. The results of these tests were compared with immersion-only conditions. Scanning electron microscope (SEM) and energy-dispersive X-ray (EDX) techniques were also used to evaluate the corrosion processes and compare them with atmospheric exposure specimens. EIS was found to measure the corrosion associated with on-vehicle exposure, thus providing an excellent screening technique for evaluation of the performance of EG automotive sheet steel.

Jan 1, 1990

By Jos. R. Guiteras

The present discussion first presents data to justify the fireproofing of mine shafts. This is followed by a brief outline of fireproofing methods with examples from practice. A summary of authoritative recommendations on fire prevention concludes the discussion. Acknowledgment is made to D. J. Parker, district engineer, Mine Safety Station, Salt Lake City, Utah, for his valuable criticism of the paper. Fireproofing a mine shaft implies lining the shaft with fireproof material or rendering fireproof the material already composing the shaft lining. A brief study of the part mine shafts and shaft stations have played in disastrous end tragic underground fires furnishes convincing evidence that every possible effort to make all mine shafts fireproof is amply justified. The fire hazard in coal minus obviously is much greater than in metal mines. In this discussion the point of views is mainly that of the metal miner; it is tine opinion of the writer that all fires in metal mines are preventable.

Jan 1, 1939

By R. Q. Shotts, H. J. Hager, A. C. Richardson, G. D. Coe

"INTRODUCTION In the State of Alabama few mines produce coal clean enough to be marketed directly without being washed. This is particularly true where the coal is to be used for the production of metallurgical coke. In washing plants where single-compartment jigs alone are used to treat a large range of sizes, it has been found that the washed coal finer than 1/4-inch contains a large proportion of free impurities and is much higher in ash content than are the coarser sizes. To reduce the ash content of this fine material with jigs usually entails a greet reduction in capacity and a loss of coarse coal in the refuse. This investigation, conducted by the Southern Experiment Station of the United States Bureau of Mines in cooperation with the University of Alabama and the Alabama By-Products Corporation, was undertaken to determine whether the fine washed coal from jigs could be economically re-treated on coal washing tables.COALS TESTEDThrough,the cooperation of the Alabama By-Products Corporation, samples of fine-sized washed coal were obtained from their washeries at Bradford and Gamma.The Bradford mine, on the Black Creek bed, yields a low-ash, medium-volatile coal with fairly good coking properties. This coal is blended with coal from the Mary Lee bed for coking purposes and compensates for the high ash content of the latter. The Black Creek bed is about 30 inches thick and seam analyses show an ash content of from 2.0 to 4.0 per cent. In the Bradford mine the undercut is about 6 inches high, so that a large proportion of fines is produced."

Apr 1, 1932

By E. J. Schneider

In view of the current interest in the constituents of low-temperature tar, the Synthesis of three known xylenols and their hydroxyacetic acid derivatives has been undertaken by the U. S. Bureau of Mines. One of these xylenols, the 1,3,2 derivative first reported by Steinkopf and Höpner,4 has been described by Brown and Branting.5 The other two derivatives, the 1,3,5 first reported by Schütz6 and the 1,2,3 reported by Steinkopf and Höpner, have now been studied in greater detail. In the present work the synthesis of 1,2,3-xylenol and 1,3,5-xylenol was repeated, with some improvements in the former. The hydroxyacetic acid derivatives were also prepared, and it was found that while the melting point of the 1,2,3 derivative agreed with that of Steinkopf and Höpner. that of the 1,3,5 derivative was found to be 111° instead of 85 to 86° as reported by Schütz, by Steinkopf, and later by Bruckner. The discrepancy between the melting-point figures is doubtless due to differences in the purity of the xylenols used in the synthesis of the acids. Schütz obtained his 1,3,5 acid by recrystallizing an impure sample obtained from a mixture of xylenols. The difficulty of obtaining a pure acid by starting with a mixture is demonstrated by Bruckner, who despite painstaking efforts was unable to obtain the pure 162.5° melting 1,2,4 isomer from a mixture that persistently melted at 138° C. Steinkopf did not repeat Schütz's work but merely used the latter's figures in compiling a table. Bruckner, on the other hand. apparently also made the acid (by an improved method), and it is difficult to explain his checking Schütz's figure, unless it is that he, too used a symmetrical xylenol obtained from a tar and not prepared synthetically, as was the one reported in this paper.

Jan 1, 1929

By Paul M. Tyler

One by one new metals come to share the burden of modern industry. Long before the Christian era potters and glass workers employed fine and costly blue pigments that contained cobalt. Cobalt blue class has been found in the tombs of the Egyptians and in the ruins of Troy, and many of the colors used by the ancient Greeks and Romans contained cobalt. The ancients, however, were apparently unaware that the colors they used were caused by cobalt, and it was not until late in the 17th century that the existence of the element was recognized, Writers in the Middle Ages referred to "cobalos" as an evil spirit that haunted mines and caused trouble to the miners. Subsequently the German worms "Kobold," meaning goblin, came to be applied to any baffling mineral and particularly to minerals that resembled ores but failed to yield metal when smelted. Even to-day there is something of an air of mystery about cobalt, and a medieval cloak of secrecy still surrounds many of the metallurgical processes employed in its production. "Zaffre" was mentioned about the middle of the sixteenth century by Biringuccio, and in 1735 the metal war, first prepared by G. Brandt. To preparation of cobalt compounds, however, must have been carried on in at least a small way ever since the opening of the silver-cobalt deposits of Schneeberg in 1470. By 1790 there were 25 works engaged in the industry, rust of them located in Saxony, but the total output of these works probably did not exceed 300 tone of cobalt annually, mostly in the fore of smalt. The smalt which contained approximately 6 per cent cobalt was sold in Venice in 1520 at about 16 cents a pound. A few refineries in Holland supplied the Irish linen trade, contributed a farce amount to the Dutch linen industries, and alto provided smaller quantities for the manufactuer of litmus in Holland. A complete description of the early [histor,] of the cobalt industry in Saxony, is given by Mickle in the Deport of the Bureau of Mines of Ontario, vol. 19, 1913, pt. 2, pp. 234-251.

Jan 1, 1930

Detect fires in or near mine shafts, isolate smoke filled areas, and remotely extinguish fire. Approach A system (of sensors, automatic alarms, an aboveground control console, remotely operated ventilation doors, and sprinklers) has been built from off the-shelf components, and fire, tested in two mines. How It Works The system uses three different kinds of sensors that can detect the heat or smoke of a fire and automatically actuate alarms. When the alarm sounds in the control center on the surface, water sprays in the mine shaft and shaft station areas can be remotely turned on to deluge both the inside and the outside of the mine shaft's wooden support structure. To protect miners from toxic fumes, smoke control doors can be closed or opened, either remotely from the control center or directly by miners using the manual or electrical actuators at the door locations. Man doors built into each ventilation door allow persons to pass without opening the main door.

Jan 1, 1977

By Jürgen F. Brune, Liming Yuan, Alex C. Smith

To provide insights and assistances for the optimization of ventilation systems for U. S. under-ground coal mines facing both methane control and spontaneous combustion issues, a computational fluid dynamics (CFD) study is being conducted to investigate the effect of the ventilation scheme on the prevention of spontaneous combustion in longwall gob areas. This report focuses on the flow patterns within the gob under three different ventilation systems; one-entry and two-entry bleederless systems as well as a three-entry bleeder system. The gas flow in the caved gob area is simulated as a laminar flow through porous media while the gas flow in ventilation airways is simulated as a fully developed turbulent flow. The air flow patterns are visualized using flow path lines. Air velocity contours and vector data are also obtained. The possible location of critical velocity zones where the gob is most liable to spontaneous heating is discussed.

By T. J. Batchler, T. M. Barczak

The Code of Federal Regulations (CFR) requires that the transverse load capacity of stoppings be equal to or greater than traditionally accepted in mine controls, which for block stoppings is generally accepted as 39 psf as referenced in the preamble to the CFR standard. This measure is based on physical testing of a freestanding wall in accordance with ASTM E 72 specifications, where our past research has shown that the dominant parameter is the tensile strength of the sealant. A new protocol based on rigid arch loading of the structure is proposed to determine the true transverse load capacity of block stoppings. Arching is achieved by the restraint of the stopping against the mine roof and floor, whereby compressive forces are developed within the wall. A laboratory procedure using the NIOSH Mine Roof Simulator (MRS) to simulate rigid arching of block stoppings was developed and results verified through full-scale in-mine tests. The rigid arch tests have demonstrated transverse load capacities more than an order of magnitude higher than the ASTM E 72 evaluation method from which the 39-psf requirement is derived. More importantly, the rigid arch tests have shown that the load capability is dependent on the physical properties of the block and geometric properties of the wall and not the sealant.

By J. W. Horne

The United States Bureau of Mines in cooperation with the State of Colorado at the University of Colorado has conducted experiments to determine the amount and composition of the non-condensable gases evolved when crude shale oil is distilled under pressure. Hydrogen sulphide is one of the components found in the complex mixture of Gases produced by the distillation of shale oil under pressure. This paper deals with the apparatus and method used in determining the amount of hydrogen sulphide evolved in the laboratory experimental cracking stills. The study required a complete extraction of all the hydrogen sulphide from the gas stream after it left the water-cooled distillate condensers and before the gas stream entered the charcoal absorber for removing the light naphtha. In devising the method it was necessary to take into account a constant variation of velocity, pressure, and percentage of sulphide in the total gas stream coming from the still. Ordinarily, the quantitative determination of hydrogen sulphide in gas is made by analyzing small samples taken at regular intervals. This estimation can be accomplished by use of the Bunts gas burette as modified by Tutriler, or by a similar method. In the industries where the flow of gas is constant and of uniform composition, this practice is sufficiently accurate for plant control. For experimental work where many variables have to be taken into consideration, as in the case at band; these methods are not applicable.

Jan 1, 1931

By C. L. Karr

The U.S. Bureau of Mines is currently investigating the use of genetic algorithms (GA's) for solving optimization problems. This computer search technique, based on the mechanics of natural genetics, was used to perform simple least squares curve fitting. Three examples are presented in which a GA manipulates binary coded strings to produce near-optimal solutions to least squares curve-fitting problems after having viewed only a small portion of the search space. The examples include fitting data to the equation of a line, the equation of a parabola, and the Ree-Eyring equation.

Jan 1, 1991