Search Documents

By R. L. Cosgriff

A commercial, battery-powered mine vehicle has been equipped for remote operation in coal mines. This vehicle is controlled by an operator from the remote station. Command signals originating at the remote station as well as video and data signals originating on board the vehicle are relayed between the remote station and vehicle using a single coaxial line. This coaxial line is normally 2,000 feet in length and is reeled in and out from a drum mounted aboard the vehicle The vehicle has a maximum speed of 6 ft/sec and a minimum speed of 4 ft/sec using 36-volt excitation of the traction motor. If this traction motor is excited by two of the three batteries, 24-volt excitation, the vehicle will travel at approximately 2 ft/sec. The speed can be reduced by the operator to 1 ft/sec. This vehicular system has been tested in coal mines. Presently, the major limitation of this system is associated with fatigue failure of the splices in the coaxial line and lack of mobility caused by its 3-wheel design.

Jan 1, 1974

This report provides the results of an industrial engineering study that assessed the safety and efficiency of underground ore handling in U.S. metal mines. One of the primary findings of the study was the improvement needed in controlling muck size in the ore handling stream. Oversize ore causes much additional labor, creating work stoppages and is a principal cause of accidents in metal mines. This report includes data on block caving, back cut and fill room and pillar, shrinkage stoping, and sublevel stoping.

Jan 1, 1974

By W. T. Abel

The Bureau of Mines tested 48 materials for their ability to absorb H2S from hot simulated producer gas (1,000°-1,500° F). The material found best from the standpoint of absorption capacity, durability, and amenability to regeneration was sintered pellets of 75 percent fly ash-25 percent Fe203. The performance of this absorbent under simulated and actual conditions is described. The effect of absorbent composition, absorbent temperature, steam content of the gas, and tar vapors and dust in producer gas is discussed.

Jan 1, 1974

By Gordon E. Fletcher

This Bureau of Mines report outlines the atomic absorption analysis of oilfield brines for barium, calcium, copper, iron, lead lithium, magnesium, manganese, potassium, sodium, strontium, and zinc, using the method of additions. The advantages of using atomic absorption are discussed. The method of additions was chosen to overcome large matrix interferences usually found in brines; techniques of overcoming chemical, ionization, and background interferences are also described. The method was used to analyze several hundred oilfield brines and found to be rapid and reasonably accurate. A solvent extraction method was used to concentrate lead, copper, zinc, and iron in low-level samples.

Jan 1, 1974

By Lewis V. Wade

This report provides background information concerning a mine roof simulator currently being considered by the Bureau of Mines. The simulator is a mechanical device with the ability to simulate the forces and displacements associated with mine roof over an area 20 by 20 feet. The topics covered in the report include a conceptual description of the system, definition of system capabilities, discussion of how such capabilities were decided upon, description of available control modes, and a comparison between the mine roof simulator facility and similar facilities existing elsewhere.

Jan 1, 1974

By J. M. Stuve

Low-temperature adiabatic heat-capacity determinations were made by the Bureau of Mines in the temperature range from 5 to 300 K for the two crystalline modifications of zinc sulfide, sphalerite (ß) and wurtzite (a). The entropy at 298.15 K of sphalerite was evaluated as l4.02±0.04 cal/deg mole and wurtzite, l4.06±0.04 cal/deg mole.

Jan 1, 1974

By R. V. Ramani, P. M. T. White, D. Sutton

Appendix I. Part 1: Description Of Geology & Reserves System Introduction The Ore Evaluation and Reserve programs have been developed to aid in the evaluation of coal deposits, both qualitatively and quantitatively. The "Weighted Moving Average" technique used provides considerable flexibility in dealing with diverse parameters with differing distribution characteristics. Determination of Model Constants "a" and "k" - Unit 1 The flexibility of the method in dealing with diverse value parameter distributions lies in its ability to cater to the individual characteristics of each. These characteristics are embodied in the values determined for constants "a" and "k", namely, local and regional variations in value distributions, respectively. The empirical method used attempts to optimize the "a" - "k" combination. Realistic values for "a" and "k" are entered into the program together with sample values for the required parameters and their respective coordinate location values. All the values within a specified radius from the point being evaluated are used to interpolate a value at that point. (Note, the interpolated point is the location of one of the boreholes, values of which are not used in the calcula¬tion.) 3n a similar manner, interpolated values are calculated for each borehole location and for each parameter. This is done for each possible combination of "a" and "k".

Jan 1, 1974

By L. R. Herrmann

The research described in this report is the first phase of a comprehensive program for the development of a characterization for the structural properties of rock masses. The mathematical expression of the characterization is especial' tailored for use in conjunction with modern structural analysis procedures. The objective of the first phase of the project is to determine the feasibility of representing the structural properties of rock masses in terms of the analysis of an appropriate "representative volume" the results of this investigation are described in detail in the body of the report. The current state-of-the-art concerning the understanding and description of the fundamental mechanisms of rock behavior are determined from a survey of existing literature. The development of a representative volume that captures the most important of these mechanisms is described, In order not to unduly obscure the fundamental aspects of this development, the mathematical analysis of the representative volume is limited to plane strain conditions. A subroutine for the numerical evaluation of the proposed model (i.e., the analysis of the representative volume) is presented. The steps necessary for the incorporation of the subroutine directly into existing two-dimensional finite element structural analysis programs are described. Comparisons between the predictions of the proposed characterization and published results of simple laboratory tests are presented and discussed. Finally recommendations are given concerning suggested improvements of the model and the extension of it to the general three-dimensional case.

Jan 1, 1974

By Robert Stefanko

The growing demand for energy during the post World War I and World War II periods has prompted underground coal production to increase rapidly. This has been met primarily by mine mechanization, resulting in the development and application of new mining machine types. Correspondingly, the total connected horsepower of each machine as well as the number employed has enlarged rapidly since 1950. (2,3,9,14,16,17) Electrical consumption for each mine has also grown. In the early years of mining electrical applications, only d-c power was utilized underground. Yet, d-c machine limitations were soon realized, and many a-c systems were substituted to permit economic and efficient utilization of a-c distribution and motors. Due to the attractive torque characteristics, ease of distribution and speed control, several traction applications have continued to be powered by d-c motors. The result has been the now prevalent use of mixed a-c/d-c mine power. However, augmented electrical power employment seems to have added to underground coal mining electrical accidents.

Jan 1, 1974

By G. H. Bennett

A field experiment was performed in a production unit of an operating copper room and pillar mine to compare the support capabilities provided by resin and mechanical roof bolts. Resin and mechanical roof bolts were alternately installed in eight intersections in a single entry. Rock mechanics instrumentation was installed to measure roof sag, bed separation, convergence, bolt pullout, torque, and strain. Bolt cost and installation time are included. Two analyses of the test were made. The analysis of the rock mechanics data showed there was no definite difference between the two bolting systems. From a broader analysis on a mine-wide basis it was concluded that resin bolts gave better support. A critical view of the experiment is given in the appendix.

Jan 1, 1974

By Donald W. Scott

Chemical thermodynamic properties for the ideal gas state from 0 to 1500 K are tabulated for all of the alkane hydrocarbons through C10. These properties are based on correlations of the extant data for the entropy, vapor heat capacity, and enthalpy of formation of individual alkanes and the equilibrium constants of alkane isomerization reactions.

Jan 1, 1974

By W. K. Overbey

The Bureau of Mines conducted surface joint and stress measurements, airborne remote sensing imagery studies, compass-oriented borehole televiewer surveys, numerical simulation of fractured wells, and well productivity studies in a four-quadrangle study area of Ohio, to determine the effects of earth fracture systems on the deliverability of gas storage fields. The results of these studies indicate that much useful information about a gas storage reservoir can be obtained and put to practical use by studying--(1) oriented cores for fractures and directional permeability, (2) orientation of induced hydraulic fractures for alignment of well patterns, and (3) aerial photos and multispectral scanner imagery for general surface geology comparison and to determine if some, development patterns can be generated by such results. The absence of known tectonic elements associated with flat-lying sediments, such as faults or fracture zones that can be seen on the surface, indicates that the use of remote sensors such as radar or aerial photography is not likely to be useful in picking well locations for drilling. Studies similar to those discussed here should be conducted in gently folded and strongly folded sedimentary formation areas to determine if the increased knowledge of earth fracture systems under these conditions might be beneficial in gasfield and gas storage reservoir development.

Jan 1, 1974

By J. W. Adams

Two different techniques were wed to make measurements of the absolute value of electromagnetic noise in an operating hardrock mine, Grace Mine, located near Morgantown, Pennsylvania. Diesel-powered haulage equipment is used in this mine, and the electromagnetic noise environment it creates was measured to see how it differs from the environment created by electric-powered haulage equipment. One technique measures noise over the entire electromagnetic spectrum of interest for brief time periods. Data are recorded using broadband analog magnetic tape and are later transformed to give spectral plots. The other technique records noise amplitudes at several discrete frequencies for a sufficient amount of time to provide amplitude probability distributions. The specific measured results are given in a number of spectral plots and in amplitude probability distribution plots.

Jan 1, 1974

By Fred D. Wright

The objectives of this research were: 1. to determine the stability relationships of coal mine roof rocks which are cut by fractures or intersecting joints with and without roof bolts, under various sets of conditions including horizontal formation pressures, inclination and coefficient of friction of joints, bolt loads, roof spans and rock properties; and 2. to develop criteria for the design of roof bolt sys terns for such roofs. The problem was studied by mathematical finite element models and by laboratory models. From the results of the mathematical and laboratory models, equations were derived to express the relationships listed above for cracked, single-layered roof beams and design tables for such beams are included. The analysis was then extended to include multi-layered cracked beams reinforced by roof bolts and a method for analyzing and designing bolting patterns for such roof rocks is presented.

Jan 1, 1974

By Barry L. Warner

This program involves the evaluation of means for suppressing fires on underground coal mine conveyor belts. Full scale conveyor belt fire tests were conducted to determine the requirements of automatically actuated water sprinkler, high expansion foam, and multi-purpose dry powder extinguishing systems, and of various fire detection devices, necessary to adequately protect underground belt heads. The program included the development of a suitable MI scale conveyor belt test fire, conducting of fire tests in which extinguishing and detection systems and equipment were evaluated, and testing to evaluate the effects of the coal mine environment on detection equipment. Preliminary testing conducted to develop a suitable test fire revealed that fire can propagate on some conveyor belting classified as fire-resistant. New fire-resistant PVC and new non-fire resistant rubber belts were used in the full scale fire tests. These tests indicated that a single branch line sprinkler system with relatively low water pressure provides adequate belt head protection. High expansion foam and multi-"purpose dry powder extinguishing systems as presently specified by regulation were found to be suitable for belt head protection, although care is required with powder systems to assure adequate distribution. Thermal type detection devices were found to be most practical for conveyor belt protection, with combustion products and optical detection methods having serious disadvantages.

Jan 1, 1974

This report presents the results of a study of mill tailings disposal practices and potential tailings dam stability problems. Recognizing the long period of time that would be required to develop the technology and practices necessary to significantly improve refuse disposal safety, the Bureau initiated this research effort as a first step in that development. Volume 1 includes a summary of conclusions and recommendations resulting from the overall research effort; discussions of disposal systems and methods, geology, seismicity, hydrology, and materials characteristics; evaluations of investigational techniques; discussions of usable interim generalized investigational, analytical and inspection procedures; discussion of general principles and presentation of a tailings technology manual outline; and discussion of needed future research am recommended programs.

Jan 1, 1974

Volume 2 presents the results of studies of Phelps Dodge Corporation's tailings embankments numbers 1West and 2 West, at Morenci, Ariz. The work involved compilation and description of pertinent factors relating to the physical features and operational characteristics of the facility, including information on embankment construction practices; investigation and research of the general geologic and seismicity characteristics of the site and vicinity; limited field exploration and materials sampling and testing at the site; installation and limited monitoring of piezometers, surface movement markers, and slope indicator casing; limited laboratory testing of materials to evaluate the basic index and engineering properties of the embankment and tailings materials; selected engineering analyses of the embankment for various types of potential "failure" conditions; and includes appendices.

Jan 1, 1974

Three complete connector assemblies and six separate contacts were submitted to a series of tests to establish the connectors permissibility and compliance with U. S. Bureau of Mines research Contract #H 0110423 D.C. portion. Test Procedure TPC-0118 was coordinated, and the test plan approved by the Bureau as fully complying with the intent of the contract for the direct current connectors. The components and connector assemblies have been demonstrated in testing that they meet or exceed all the requirements of the test procedure.

Jan 1, 1974

By Richard A. Busch

Inadequate engineering design criteria for coal refuse embankments has allowed hazardous impoundment structures in coal mining areas to be created. A necessary first step to develop adequate design criteria is the determina¬tion of basic, respresentative physical property data on the materials that constitute typical refuse embankments. An extensive field and laboratory program was undertaken by the Federal Bureau of Mines. Much physical property data was generated. Additonal petrographic analysis and large scale triaxial compression testing was performed by others. The data presented here should aid in establishing design parameters for coal refuse embankments

Jan 1, 1974

By R. Stefanko

This study concerns itself with the effects of diesel exhaust on mine ventilation systems. The approach here consisted of the development of mathematical models for emissions, dilution, and dispersion of gaseous pollutants from diesels. The general scheme was to use partial differential equations to predict concentration growths. Specifically, the following situations were modeled: 1. A single stationary diesel engine working in a single roadway. 2. A single diesel engine moving with uniform velocity in a single roadway. 3. Multiple diesel engines moving continuously in a cycle in a roadway with appreciable leakage. 4 Multiple diesel engines moving continuously in a cycle in a roadway with little or no leakage. 5. Multiple diesel engines moving randomly in a roadway with uniform air velocity.

Jan 1, 1974