Search Documents

By Ronald A. Munson

Samples of the naturally occurring zeolites phillipsite, clinoptilolite, erionite, and chabazite have been surveyed for their gas adsorption, ion exchange, and other characteristics. Chabazite and erionite, which are generally more stable, also have higher methane adsorption capacities than do the other natural zeolites. Both natural erionite and natural chabazite are classified as small-port zeolites on the basis of their inability to adsorb chlorotrifluoromethane. In the range of 8 to 100 mesh, the adsorptive capac-ity of natural zeolites is improved only slightly by a decrease in particle size. The capacity of natural clinoptilolite to adsorb methane is increased by cation replacement by the hydrogen ion and decreased by exchange with calcium ion. Natural phillipsite, which is easily decomposed by heat, adsorbed methane to a limited extent.

Jan 1, 1973

By B. V. Johnson

The Federal Bureau of Mines has conducted research in support of the National Aeronautical and Space Administration's (NASA) Apollo program to acquire fundamental scientific and engineering knowledge of lunar-mineral resources for NASA's Office of Advanced Research and Technology. Equipment and techniques were developed to conduct soil shear tests in a simulated lunar environment. Shear tests performed with this equipment in ultrahigh vacuum and controlled laboratory atmosphere showed that simulated lunar soil increased in strength in the simulated lunar environment.

Jan 1, 1973

By Floyd C. Bossard

Major air-cooling facilities have been installed and are operating underground in U.S. copper mines (at Butte, Montana and Superior, Arizona), South African gold mines, European coal mines, Zambian copper mines, Kolar gold mints in India, Coeur d'Alene mines of Idaho, plus other locations. Mining districts that utilize spot cooling and local air-cooling facilities would increase the above listing many times. The principal objectives of underground mine air cooling systems are to; 1. Extract heat and water vapor from the mine air and provide for their removal from the mine via (a) water pumped to surface or (b) discharged mine exhaust air. 2. Provide acceptable artificial ambient conditions for efficient working mine development and production areas. 3. Recondition used air, thus supplementing the limited mine ventilation balance. In deep South African gold mines, when rock temperatures exceed about 105°F, cooling of underground air becomes necessary for the poorly ventilated sections of the mine. By U.S. standards, air conditioning in poorly ventilated mines usually commences when the virgin rock temperature exceeds 100°F. On the other hand, well ventilated deep vein-type mines in the U.S. have been able to forego general cooling of mine air until the mines have been extended to such depths that the virgin wallrock temperatures have exceeded 115° - 120°F. It must be noted that spot-cooling of selected development headings may be required in many mines where rock temperatures exceed 100°F. Such local air-cooling practices permit the driving of long headings for exploration or extended development prior to holings which result in establishment of primary ventilation circuitry. The following summary reports on current practices of cooling and dehumidifying mine air. General system descriptions with important details will hopefully permit the reader to gain an understanding of the subject. A list of references is provided for this serious investigator who desires a more thorough knowledge-base and who is responsible for the design of a mine air-cooling system.

Jan 1, 1973

By F. Cherpereel, R. Gabillard, J. P. Dubus

We present an electromagnetic method taken from the well known radiogoniometer that allows us to locate at the surface of the ground the vertical axis of a magnetic antenna transmitter buried at a depth h in the earth. The method and the equipment achieved are called R. E. P. E. (Relevé Electromagnétique de Points Enterrés). They are daily used to accurately survey old quarries by using triangulation instruments at the surface of the earth rather than in galeries where the setting difficulties considerably reduce their accuracy and increase the work length. The results of several surveys allow us to give the optimum working conditions of the instruments and show that, when the transmitter is at a 20 meters depth, its position is known at the surface with an error lower than 1 centimeter. The power transmitter is of about 8 watts and we can find its location with an error smaller than 1 meter when buried at a depth of about 100 meters. This equipment may be successfully used for location of subsurface miners. The space surrounding the transmitter must then be free from ferromagnetic bodies.

Jan 1, 1973

By E. Aamland

Preparation of high-purity magnesium-yttrium alloys by electroreduction of Y2O3 dissolved in a YF3-LiF bath and the subsequent deposition of yttrium in a molten magnesium cathode was investigated in laboratory-scale apparatus. Parameters such as temperature, current density, and electrolyte density were studied. Electrolysis was conducted in a specially designed MgO diaphragm cell at temperatures ranging from 780° to 970° C. Alloys containing up to 55 weight-percent yttrium were prepared at cathode current efficiencies of 21 to 60 percent. Cell design and operation are described, and some of the limiting conditions pertaining to the method are discussed.

Jan 1, 1973

By G. P. Sturm

This work was undertaken by the Bureau of Mines in cooperation with the Environmental Protection Agency to determine photochemical specific reactivities of emissions from automobiles using leaded-premium-and regular-grade fuels and prototype lead-free fuels of comparable octane quality. Emissions were photoirradiated in a 100-ft3 environmental (smog) chamber constructed of aluminum and Pyrex glass at three sets of initial hydrocarbon (HC) and oxides of nitrogen (NOx) concentrations. Reactivity was measured and expressed in terms of rate-of-NO formation (RNo2) and dosages of oxidant, peroxyacetyl nitrate (PAN), peroiypropionyl nitrate (PPN), and formaldehyde (HCHO). The results indicate that the evaporative emission samples and the evaporative plus exhaust emissions samples from the lead-free fuels have, in general, higher reactivities per gram than those from the leaded fuels. For the samples containing only exhaust emissions, the only trend observed was the lower specific reactivity exhibited by the leaded premium fuel exhaust. These differences in specific reactivity are taken to reflect the differences in hydro-carbon composition of the fuels and their evaporative and exhaust emissions rather than any difference in lead content per se.

Jan 1, 1973

By B. J. Scheiner

Silver ores from the Candelaria District, Nevada, and Round Mountain District, Colorado, were investigated mineralogically and metallurgically. Silver minerals of four distinct groups were identified: (1) silver sulfide; (2) argentojarosite; (3) silver contained in the iron oxide; and (4) manganese carbonate-oxide minerals, Electrooxidation and acid-chloride leaching techniques were investigated as means of altering silver minerals, and their effects on subsequent silver extraction were determined. Application of the knowledge obtained from mineral leaching studies resulted in development of a sulfur dioxide-sodium chloride leaching sequence for extracting silver from these types of ores. Silver extractions of 80 to 85 percent were obtained by leaching the ores with a sulfurous acid-sodium chloride system. This was an increase of 9 to 61 percent silver extraction over that obtained by conventional cyanidation techniques.

Jan 1, 1973

By Jesse J. Brown

Over 60 simple; were prepared and forwarded to Dr, S. Z. Toma, TPO, PMSRC as a result of this project. Included among these samples were various low temperature forms of silica. Samples of quartz, cristobalite, and tridymite with iron, manganese, and titanium impurities present were prepared. In addition, a long series of samples both wet ground and dry ground for times from 1/2 to 8 hours were prepared. Numerous miscellaneous samples were submitted which included kaolinite, calcite, muscovite, illite, montmorillonite, Ba3(P04)2, and YPO4 among others, in response to special requests from the TPO. The silica rich portion of selected binary (CA 203-Si02, In 203-Si02, Li20-Si02) Na20-Si02, PbO-Si02, SnO2-Si02, Sn02-Si02 BaGa204-SiO2 and SrGa204-Si02) and ternary systems (Na20-Ga203-Si02 and Li20-Ga203-Si02) was investigated to determine the effects of solid solubility on the stabilization of the high temperature forms of tridymite. In addition to the determination of the extent of these crystalline solubilities, observations were made. on the mechanism of the transformation of silicic acid to tridymite and the rate of the reaction in the presence of foreign ions,

Jan 1, 1973

By G. C. Price

This study traces the development of the bucket-wheel excavator, points out the differences in the German- and American-type wheels, and gives the major design criteria and the advantages and disadvantages of bucket-wheel operations. A computer program, written in FORTRAN IV for use with an IBM 360 computer, simulates the operation of the digging components of a bucket-wheel excavator. By supplying certain mining dimensions, soil characteristics, and machine design specifications, this program will print out a time study of the various components of an operation, power calculations for the operation, and production data. This program, when combined with a truck, belt, or rail program, should be helpful in planning a complete mining system In material suitable for a bucket-wheel excavator operation.

Jan 1, 1973

By H. H. Fields, Stephen Krickovic, M. G. Zabetakis, Albert Sainato

The Bureau of Mines is in the process of degasifying a virgin area in northern West Virginia from the base of an 839-foot -deep vertical borehole. An in situ gas pressure hole 199 feet long, and seven degasification holes ranging in depth from 500 to 850 feet (average 618 feet) were drilled in an 8-foot-thick virgin Pittsburgh coalbed from the enlarged (14-foot-diameter) bottom of this borehole. The in situ pressure at the back end of the hole and the range of gas and water flows from degasification holes as they were completed and closed off were 203 psi, 79,000 to 257,000 cfd (average 160,000 cfd), and 5 to 8 gpm per hole (average 6.8 gpm), respectively. Twenty-four hours after the seven holes were connected through individual water traps to a common collector for natural venting of the gas through pipes to the atmosphere, the total gas and water flows and the in situ pressure dropped, respectively, to 971,000 cfd, 1.3 gpm, and 18 psi. Eighty days later the corresponding values dropped to 529,000 cfd, 0.50 gpm, and 13 psi. After 180 days of degasification, 91 million cubic feet of gas had been removed from the affected virgin area. This represents 60 to 70 percent of the gas calculated to be contained in the area of coal affected by the holes.

Jan 1, 1973

A study was conducted by the Bureau of Mines to evaluate natural gas as an automotive fuel and to provide guidelines for optimum engine adjustments for low exhaust emissions. The study was conducted using a single-cylinder engine, a multicylinder engine, and a total of eight vehicles. Results from single-cylinder engine tests showed that the light-load, lean-limit misfire region for natural gas begins at an air-fuel ratio between 150 and 160 pct of stoichiometric. Changes in ignition timing significantly influenced emissions of nitrogen oxides and hydrocarbons, but had little effect on carbon monoxide emission. Low emissions can be achieved with current-design engines by adjustment of engine parameters, but only with heavy penalty to engine performance. Emissions from vehicles fueled with natural gas are virtually unaffected by ambient temperature change within the range 20° to 100° F. The organic emissions from engines fueled with natural gas were estimated to be 22 to 25 pct as reactive as the emissions produced using gasoline. Levels of exhaust emissions from vehicles fueled with natural gas were unchanged over 10,000 miles of normal driving.

Jan 1, 1973

By John W. Adams

The present status of the National Bureau of Standards program is that many magnetic tapes of analog data have been recorded in four major mines. Each mine uses different types of equipment. In addition, some surface measurements of noise have been made at two additional mines. Two types of recordings have been made: (1) broadband measurements for spectral plots and (2) narrowband measurements for amplitude probability density (APD) plots. Only data from one mine (Robena #4) has been processed and was, presented at this workshop. The short-term goals are: (1) finish processing data from the other mines, (2) establish or reduce measurement system uncertainties, (3) put Robella report into final form for distribution, and (4) hold a review to determine what has been done, to distribute and to interpret the preliminary data, and to determine what still needs to be done. Long-term goals are: (1) complete final reports on each of the mine trips, (2) establish techniques for predicting noise in mines already visited and establish uncertainty bounds for these predictions, and (3) establish techniques for predicting noise in mines that have not been visited (but that use similar equipment to those visited) and also establish uncertainty bounds for these predictions. Specific factors or formats to be presented include: (A) For underground broadband measurements: 1. 300 Hz to 100 kHz spectral plots 2. 300 Hz to 384 kHz spectral plots 3. 300 Hz to 192 kHz spectral plots 4. 300 Hz to 6kHz (subject to change to 3 or 12 kHz) spectral plots (B) For surface broadband measurements: 1. 300 Hz to 6 kHz (or 12 kHz) spectral plots 2. 300 Hz to 3 kHz spectral plots (C) For underground narrowband measurements : 1. APD plots at 12 frequencies from 10 kHz to 32 mHz of magnetic field strength 2. R. M.S. and average values will be calculated based on time averaging for these plots (D) Sample spectral measurements of: 1. Roof-bolt voltages 2. Trolley wire-to-rail voltages 3. Phone line currents

Jan 1, 1973

By W. D. Kaiser

Recent legislation and expected future legislation is aimed at reducing the dust levels developed in underground coal mines. Several techniques for reducing dust levels are being evaluated. One of these is the modification of cutting parameters such as feed rates, cutting speeds, and pick configurations in order to reduce the amount of dust generated. In order to evaluate the feasibility of modifying cutting parameters to reduce dust, the Bureau of Mines commissioned Battelle to construct a small scale mining machine which could be used for evaluating the effects of those changes in cutting parameters. Specific features of this machine were that it should be highly instrumented to measure various cutting parameters, should have a wide range of feed and speed controls, and it should be possible to vary the pick configurations and geometries on the machine. In addition, it was desired that this machine should have cutting capabilities which greatly exceed present coal mining practice and also that the unit should be small enough and portable enough that it could be taken into and out of operating coal mines with a minimum of interference with the normal coal mine operations. The first step in constructing a machine to meet these requirements was to determine the cutting forces and approximate sizes of components which would be required to cut at the speeds and feeds specified by the Bureau of Mines. Initial calculations using; published data on cutting forces indicated that cutting forces in the neighborhood of 5,000 lbs and power levels of approximately 30 horsepower would be adequate for the application. However, further data developed during the course of the project indicated that when low efficiency picks are used, cutting forces and powers can be two to three times as high as these initially estimated values. After several design iterations, a design was chosen in which the cutting head was driven by four hydraulic motors which were part of a hydrostatic transmission which, in turn,

Jan 1, 1973

By Joseph Grumer

In addition to nine powder and gaseous extinguishants of propagating Pittsburgh seam coal dust-air explosions earlier evaluated,6 10 other powders have similarly been evaluated under like conditions such that wall quenching of the coal dust-air flames was virtually absent and the dust concentration was temporally and spatially uniform to within about ±5 percent. None of the newly examined extinguishants was better than Purple-K (potassium bicarbonate); the 10 of this report are anhydrite (calcium sulfate), monobasic (4 types) and dibasic ammonium phosphate, natural and synthetic cryolite (sodium fluoalumi-nate), sodium sulfate, and tricalcium phosphate. Except for anhydrite, sodium sulfate, tricalcium phosphate, and the cryolites, these materials were about equally effective, when present in relatively low concentrations (weight-percent of the coal dust-extinguishant mixture). The maximum oxygen concentration for the extinguishment of otherwise uninhibited coal dust explosions and the influence of coal dust particle size and the volatile content of the coal were also explored. For the present, the choice of the inhibitor among the good ones evaluated is not as critical as the system to be used to deploy the extinguishant against a coal dust explosion.

Jan 1, 1973

By L. A. Schutz

Personnel of the Bureau of Mines have conducted investigations in the principal asbestos mines and mills in the United States, to determine the concentration of airborne asbestos fibers in the workplace, and to establish the exposure of workers to such fibers. 'The surveys were conducted using the sampling and evaluation method recommended by the National Institute for Occupational Safety and Health. The method consists of collecting the air-borne sample on filters and, after appropriate sample preparation, counting the fibers utilizing phase contrast microscopy. The results of the investigation show that fiber concentrations are low in the asbestos mines but high in the asbestos mills, ranging well above 5 fibers/ml of air based on a count of fibers greater than 5 urn in length.

Jan 1, 1973

Underground coal mine tracked vehicles have been studied to determine the state of the art and how brakes might be added to the coal haulage cars. Specific areas of interest are: brake sys terns, couplers, car trucks and car handling procedures. Problems related to adding brakes to the haulage cars appear to be: the limited amount of room to mount the brakes on the cars, brake line connection between rotary dump cars, achieving desirable braking characteristics without over complicating the system and keeping the installation cost to a reasonable figure. This document combines the information contained in the first issue of the "State-of -the-Art of Underground Coal Mine Tracked Vehicle Brake Systems," BRL Report No. 6080, with that contained in a subsequent monthly report.

Jan 1, 1973

By Bruce I. Thomas

The Fairbanks mining district forms an arc 40 miles long and 8 miles wide on the north side of the Tanana Valley in central Alaska. This is a region of broad valleys and rounded hills that range in elevation from 600 to 2,600 feet Lode-gold production started in 1910 and has continued sporadically to the present, but the largest single mine produced only 40 tons per 24-hour day. Total recorded lode-gold production of the district is 241,000 fine troy ounces of gold from ore that averaged 1.32 fine ounces per ton. The ore was mined chiefly from narrow veins and veinlets alined along anticlinal folds at Ester Dome and the Pedro Dome-Cleary area. The only proven reserves are reported to be at the Ryan Lode at Ester Dome and at the Keystone Mines, Inc., holdings in the Pedro Dome-Cleary area. An inferred lode-gold resource for the district of approximately 4,000,000 ounces is considered to indicate only the order of magnitude of the lode-gold potential because of the absence of detailed data needed to evaluate the numerous deposits.

Jan 1, 1973

By B. Demoulin, J. Fontaine, R. Gabillard, P. Degauque

To realize a radiowave communication along mine galleries a few kilometers long without repeater, we show that it is possible to use a coaxial cable bearing an important surface transfer impedance like a transmission line with an inductive coupling to the transmitter and the receiver. We determine the electrical and geometrical constants of the cable and the optimal frequency.

Jan 1, 1973

By Allen Q. Howard

An approximate solution to the electromagnetic boundary value problem consisting of a horizontal cylindrical conductor buried in a lossy half-space and excited by an arbitrarily oriented magnetic dipole is found using an iterative perturbation technique in a double Fourier transform space. This model is used to gain insight into the anomalous fields due to strong scatterers such as pipes or tracks which would be in close proximity to an EM mine rescue operation. The novel, three-dimensional aspect of the problem (i.e., the source) imposes the complexity that the current in the cylinder is not uniform. The field expressions are ideally suited to evaluation using FFT algorithm.

Jan 1, 1973

By Foster Fraas

This report describes the application of pulsed magnetic fields derived from alternating and intermittent magnetizing currents. Application of such pulsed magnetic fields to the matrix-type separator permits (1) the complete discharge of the magnetic fraction with wet feeds and (2) the dry separation at particle sizes down to 325 mesh. At smaller particle s indications are that frequencies above 60 hertz will be required. Applications of intermittent magnetizing current to the cross-belt separator give the cross-belt-separator an advantage over the conventional constant-field cross-belt and induced roll separators; the intermittent current enables the cross-belt separator to separate matted fibrous and magnetically coagulating feeds, a type of feed that occasionally occurs with mineral, industrial, and secondary materials.

Jan 1, 1973