Search Documents

By Leo A. Schrider

A prediction for oil recovery from a pilot waterflood in the Kane oil- field, located in Elk, Forest, and McKean Counties, Pa., was made and compared to actual field performance. Water-injection and production histories, well logs, other field data, and results from laboratory tests of core material were used in this analysis. Performance of the pilot waterflood, initiated in January 1963, was predicted using a modified Craig, Geffen, and Morse calculation technique. Maximum recovery from this low permeable, preferentially oil-wet formation was predicted to be about 22,500 barrels of oil after 300,000 barrels of water had been injected into the pilot waterflood area. After additional field data were collected it became necessary to reevaluate the pilot waterflood area. The gas saturation prior to the waterflood was estimated to have been 20 percent, based on an assumption regarding the required volume of water injected to initiate oil production. In view of the actual field performance, a gas saturation of 13 percent is indicated. When this gas saturation and the method originally proposed by Craig and others are used) the predicted results are more representative. In December 1965, field performance was further analyzed using a hyperbolic-decline curve as presented by Arps. Based upon this evaluation method, the pilot water flood in the Kane sand should produce 37,000 to 42,000 barrels of oil with the injection of 300,000 barrels of water into the pattern. By continuing this secondary-recovery project to a reasonable economic limit, ultimate oil recovery may be as much as 50,000 to 55,000 barrels, or 129 to 142 barrels per acre-foot from 36.5 acres.

Jan 1, 1967

By L. F. Heising

The Bureau of Mines evaluated 42 composite samples from selected Michigan-Wisconsin iron formations by reductive roasting-magnetic separation and flotation at minus 325 mesh. Samples having poor to marginal response on initial examination by conventional methods were reevaluated by finer grinding, by reagent suite modifications, and by selective flocculation-desliming techniques. Results ranged from excellent on Menominee Range samples to relatively on Gogebic Range ores. Marquette Range samples ranged from responsive to nonresponsive, depending upon grain size and mineral association.

Jan 1, 1967

By R. F. Waters

Laboratory-scale selective volatilization methods developed by the Bureau of Mines to recover germanium and gallium concentrates from coal fly ash and phosphorus furnace flue dust are summarized. In the better experiments between 85 and 98 percent of the germanium was recovered as the lower oxide and as sulfides, and between 75 and 97 percent of the gallium was recovered as the lower oxide and as the trichloride. Grades of the condensates were inconsistent and varied between a few tenths of a percent and 8 percent, depending on the method used. In the primary extractions of germanium alone the degree of enrichment surpassed 100 to 1, and for gallium the best ratio was 30 to 1. Upgrading of condensates by vaporization retreatment and by leaching and precipitation is discussed. An appreciable degree of mechanical preconcentration by attrition scrubbing and elutriation was possible on two fly ash samples.

Jan 1, 1967

By John E. Miller

A high accuracy Burnett apparatus for use at 12,000 psi and 0° to 65° C has been constructed at the Bureau of Mines Helium Research Center. The apparatus is patterned after Burnett's original apparatus, but the working pressure is much higher and elastic distortion can be essentially eliminated. An operating procedure to permit faster experimental measurements is suggested.

Jan 1, 1967

By R. L. Hopkins

Some typical thiacyclopentanes and thiacyclohexanes were synthesized to provide reference compounds needed for the identification of sulfur compounds in crude oils. Two general methods of synthesis were employed: (1) cleavage of 2-alkyltetrahydropyrans with hydrogen bromide followed by the reaction of the resulting dibromoalkanes with sodium sulfide and (2) the catlyzed reaction of cyclic ethers or 1)4-or 1)5-alkanediols with hydrogen sulfide. Both methods produced mixtures of 2-alkylthiacyclopentanes and 2-alkylthiacyclohexanes with 2-alkyltetrahydropyran as the starting material. The structures of the reaction products were established by analysis for sulfur; desulfurization; gas-liquid chromatography (GLC); mass, infrared, and nuclear magnetic resonance (NMR) spectra; and an alternate synthesis. The synthesis of the cyclic sulfides contributed substantially to the identification of 10 members of this class of sulfur compounds in crude oil.

Jan 1, 1967

By Charles B. Kenahan

The effects of ultrasonic radiation on the electrodeposition of copper-zinc, copper-cadmium, and copper-tin alloys from cyanide baths were investigated by the Bureau of Mines at frequencies of 18.5 and 38 kilocycles per second, and at acoustic intensities up to 0.5 watt per cm3. Significant changes occurred in the composition of the deposited alloys; some of these deposits were brighter, harder, more adherent, or of finer grain size than nonirradiated deposits. The irradiated deposits were also smoother and less porous, and they afforded better corrosion protection for the substrate metal in sodium chloride solution. The limiting current densities of the cyanide baths were increased by the application of ultrasonics. Anode and cathode current efficiencies also were increased, and cell voltages were lowered; the relationship of these effects to current density is discussed. Electrode potential measurements showed significant depolarization effects at both electrodes during ultrasonic irradiation. The resulting decrease in cell voltage was due chiefly to depolarization at the anode, and the anode became less passive.

Jan 1, 1967

By F. L. Wideman

Materials handled at metal and non-metal mines in the United States increased 10 percent compared with those of 1965 as a result of expansions in output at existing mines and development of others to meet increasing demands for mineral products. The tonnage of commercial materials mined or quarried increased as did the quantity of waste handled. Crude material from which metal or nonmetal products were derived comprised 71 percent (75 percent in 1964) of the total materials handled. Great strides were made in mining technology and there were indications that, in the future, earth moving by the mining industry will involve materials-handling systems of increasing size and complexity. Materials Handled.-Output of ore and waste at metal and nonmetal mines and quarries in the United States in 1966 totaled 3,518 million tons (3.213 million tons in 1965). The quantity of materials handled has increased at an average annual rate of 5 percent since 1962. Ore production increased 4 percent over that of 1965, also comparable to the average annual rate of increase in the last 5 years. Waste removal in 1966 increased 25 percent over that of the previous year.

Jan 1, 1967

By Robert C. Ellman

Stockpiles containing 2.3 million tons of lignite constructed in the period 1948-56 in conjunction with the construction of Garrison Dam on the Missouri River demonstrate successful stable long-term storage of lignite. Uniform and thorough compaction of each of the I-foot-thick layers by which the piles were constructed produced a bulk density of 70 Ib/cu ft. Air penetration into the stockpiles was restricted to a degree that prevents spontaneous heating or deterioration of the stored lignite, A continuing record of observations beginning with stockpiling operations in 1948 has been accumulated, This includes periodic fuel analysis, analysis of pile gases, and measurement of pile temperatures on the first large stock-pile, pile 5. This report describes the stockpiling method, the changes in heating value, pile gas composition, and pile temperature and summarizes observations from 1953 to 1964, Data accumulated attest to the stability of the stored lignite. The variation of the average heating value of periodic pile-depth samples is only 160 Btu/lb (11,990 to 11,830) on the moisture" and ash-free (maf) basis during almost 10 years of storage. Temperature levels of the pile interior are progressively decreasing. At pile surface, cyclic variations occur with the season. The only problem encountered with the large stockpiles is wind and water erosion of the pile surface. The partially successful control measures used are described.

Jan 1, 1967

By C. C. Shale

Current-voltage relationships for air at high temperature in negative corona are compared with relationships predicted by theory. Deviations are discussed. Eased on the latest theoretical concept of electron detachment from negative ions and recent findings in basic research on free electron gases, results of applied research show the existence of free electrons in air at high temperature and high field strength-to-pressure ratios.

Jan 1, 1967

By Hillary W. St. Clair

The reduction zone of the iron blast furnace is represented by a mathematical model of the chemical reactions and heat transfer that occurs between gas and solids during the deoxidation of iron oxide. The model consists of a set of equations and an algorithm whereby the equations may be solved to give the temperature and composition of gas and solids at any position in the reaction zone and at any time after a specified initial state. The model is applied to the special case in which ferric oxide is reduced by graphitic carbon and carbon monoxide produced by burning carbon in dry air. The rate of reduction, carbon consumption and maximum temperature are shown as functions of the temperature and rate of flow of the incoming reducing gas and external heat loss. The model of the reduction zone is the essential part of a general mathematical model for simulation of the iron blast furnace. The simulation model will serve as a research tool to be used in conjunction with an experimental or operating furnace. After the simulation model has been correlated with the real furnace, it is proposed that further experimentation be done mostly with the model. The real furnace will then be operated primarily to test and confirm the model.

Jan 1, 1967

By J. W. Town

Studies were made by the Bureau of Mines to determine the influence of textural features on the beneficiation of phosphate minerals (pellets) from selected bed and composite samples representing different rock types of the Western Phosphoria Formation. The particle size of the samples was reduced by attrition grinding to minus 20-, 28-, or 48-mesh depending on ore grade and gangue matrix. Sizing of the ground material showed that the phosphate pellets would concentrate in the plus 200-, 270-, or 325-mesh size fractions sufficiently so that the phosphate content was above the 31.5 :cent P2O5 required for acidulation. The phosphate content of essentially pure phosphate pellets was shown to range from 33 to 39 percent P2O5. Microscopic identification of the particles in each size fraction showed that the phosphate was either in the pellet form and readily liberated or so intimately associated with the gangue matrix that size reduction necessary Co obtain liberation was impractical.

Jan 1, 1967

By P. C. Tully

The vapor pressure-temperature relationships for saturated pure liquid nitrogen are calculated by the Strobridge equation using a digital computer. This information is presented in two tables: first) in pressure increments of 0.1 psi from 1.8 to 492.9 psia) and second) in temperature increments of 0.1° from 63.15° to 126.26° K. These tables should facilitate the calibration of temperature-measuring devices over this temperature range.

Jan 1, 1967

By Warren E. Morrison

The continuing high-level performance of the domestic mineral and mineral fuels industries during 1966 was sustained by the longest business upturn in the Nation's history. Spurred by consumer demand at home and the defense production requirements of the Viet-Nam war, the rising trend of economic activity during the year was reflected in the upward movements of the major economic indicators. At yearend the gross national product (GNP), representing the value of all goods and services produced, stood at $740 billion, $58 billion greater than in 1965. Corrected for price changes, the real value of GNP in terms of 1958 dollars was $648 billion and represented an annual increase in economic activity of 5.4 percent. Some 74 million persons were employed during the year out of a total population of 196.8 million, while unemployment fell below 4 percent. The Federal Reserve Index of Industrial Production averaged 156 for 1966, up 13 points from the previous year. However a jarring note in the 1966 expansion, and one which affected the mineral industries in particular, was the increasing pressure on prices and the threat of inflation. From 1961-65 economic growth was facilitated by relatively stable wages and prices and only mild inflation. During the period average wholesale prices hardly moved while average consumer prices rose only about I percent per year. But this long run of relative price stability ended during 1966 when consumer prices rose 2.9 percent and wholesale prices were up 3.2 percent from the previous year.

Jan 1, 1967

By C. J. Chindgren

The Bureau of Mines investigated the technical problems involved in recovering commercial-grade vanadium products from alkaline solutions of low vanadium content. Conditions were defined for precipitating calcium vanadates from sodium vanadate solutions with calcium chloride and calcium hydroxide and for dissolving the precipitates with acid, sodium carbonate, and sodium bicarbonate to obtain vanadium-enriched solutions from which either red cake or ammonium metavanadate was recovered. Calcium vanadates with CaO:V205 mole ratios of 2, 3, and 4 were produced with recoveries of 93 to 100 percent. Optimum recovery of the low-lime variety of calcium vanadate was obtained by employing excess calcium chloride and adjusting the pH to a range of 8.0 to 8.5. High vanadium extractions were obtained in concentrated solutions by dissolving the calcium vanadate precipitates with any of the reagents tested. The resulting extracts contained 25 to 125 grams V205 per liter. Conventional procedures used to precipitate either red cake or ammonium metavanadate from the enriched solutions gave excellent vanadium recoveries.

Jan 1, 1967

By W. S. Sanner

Seven samples were analyzed from the major reserves of the Bottom Red Ash bed, Northern anthracite field. The data show variations in thickness and geo-logic structure and in the amount of coal that can be recovered. Recovery of market-grade (less than 17 percent ash) coal is high for all samples, ranging from 76 tp 95 percent in the 3-1/4-by 9/16-inch sizes. The occurrence of coal containing less than 5 percent ash varies from 19.5 to as much as 57.5 percent. Crushing the coarse sizes to minus 9/16 inch increased recovery of market-grade coal in six of seven bed samples. Crushing released sufficient impurities to cause substantial increases in yield of coal containing less than 5 percent ash for all samples. Analyses of the float coal indicate that the quality of coal is comparable for all samples.

Jan 1, 1967

By W. P. Haynes

To evaluate the potential use of battery-powered vehicles, the Bureau of Mines studied the performance of a battery-powered truck propelled by a 9.6 kw dc motor in considerable detail under various driving conditions. Some of the factors investigated were: Gear ratios, payload (1,468 lb maximum), road grade, stops made per mile, and charging time. With the exception of some difficulty with brush wear, operation and maintenance of the truck was generally trouble-free. On range tests carrying an 868-lb payload a distance of about 50 miles at an average speed of about 19 mph in normal driving, the Bureau's battery-powered truck averaged 1.6 to 1.9 miles per ac kwhr input. Stop-and-go tests indicated that prospects for the use of battery-powered trucks in house delivery service within city limits are good; performance of the Bureau truck was sufficiently high for that type of service. The estimated power cost of 2.65 cents per mile while making 10 stops per mile was attractively low from the standpoint of fuel costs.

Jan 1, 1967

By Murray Weintraub

The Bureau of Mines investigated the aerodynamic factors that control the functioning of the blowcase devices used in pneumatic processes for dispersing solids. Alumina powder of 8-micron mass-mean diameter was placed in 0.75- inch-diameter by 10-inch-long cylinders} and a blowcase technique was employed. It was determined that dimensions and gas rates for discharging the powder from the cylinder by a stream of gas may be calculated by assuming a fluidization mechanism and extrapolating residues to a desired finite quantity or to zero at the terminal velocity. The state of agglomeration of a powder at discharge may be determined from measurements of the velocity required for zero residue.

Jan 1, 1967

By D. R. Mathews

The Bureau of Mines investigated the effects of tungsten and chromium, separately and combined, on improving the mechanical properties and oxidation resistance of vanadium. Binary and ternary vanadium-base alloys were prepared and tested for oxidation resistance and tensile strength. Softening occurred with less than 1 weight-percent of either tungsten or chromium, followed by strengthening with higher alloying contents. Vanadium alloys containing up to 9.8 weight-percent chromium or 14.1 weight-percent tungsten were more resistant to oxidation in air at 600° C than unalloyed vanadium. For the alloys with 12.20 weight-percent chromium or 14.56 weight-percent: tungsten, the maximum concentrations used, the lower yield strengths were about twice that of 38,600 psi for the unalloyed vanadium. Recrystallization temperatures for these alloys were 100 and 150° C higher, respectively. Alloys containing both chromium and tungsten had properties similar to those of the vanadium-tungsten alloys.

Jan 1, 1967

By James A. West

Near East region countries continued to supply a large share of the world's energy requirements in 1965. The area accounted for nearly 27 percent of estimated total world crude oil output and for about 60 percent of world exports of this commodity. Also, it was the source of more than 40 percent of the world's petroleum refinery products exports. Although other mineral industry activities remained relatively in? significant in comparison with petroleum, regional production and export of certain metallic and nonmetallic mineral commodities were of world significance. Of these commodities, chief in importance were chromium, copper, mercury, antimony, boron, potash, and phosphate Tack. The Near East region contains the largest and most productive oil resources in the world. Petroleum exploration and development operations during 1965 resulted in crude oil reserve additions of almost 8 billion barrels to increase proved reserves to 219 billion barrels at yearend, an amount equal to nearly 68.5 percent of the world's proved oil reserves. Near East countries' production of crude oil averaged a record 8.337,575 barrels per day in 1965, an increase of nearly 11 percent over that of 1964. On an annual basis, Kuwait continued as the leading oil producer in the Near East; however, Saudi Ayabia was a close second and its rate of production in late 1965 exceeded that of Kuwait. The major oil producing nations and their percentage of total area crude oil output was Kuwait, 26.0; Saudi Arabia 24.3; Iran, 22.3; and Iraq 15.9.

Jan 1, 1967

Table 1.-Aden: Production of mineral commodities [ ]

Jan 1, 1967