Search Documents

By Bernard Porter

The rate of the heterogeneous reaction between high-purity uranium metal and uranium tetrafluoride in molten lithium fluoride was measured. The apparent heat of activation for the reaction is 16.91 kilocalories per mole of UF4. A surface-controlled mechanism is suggested in which UF4 is adsorbed on the uranium metal surface. Additional UF4 reacts with the adsorbed species and the metal site to form an activated complex that decomposes to the product UF3. The reaction is an important source of metal loss in the electrowinning of uranium metal.

Jan 1, 1966

By Jr. Karr

The Bureau of Mines studied the influence of carbonization method, temperature, and carrier gas on the composition of eight different low-temperature tars produced from a Colorado subbituminous coal. A fluidized bed was compared with an entrained bed, temperature was varied from 500° C to 650° C, and external heating using recycle gas as the carrier gas was compared with internal heating using oxygen-containing gas. The entrained bed yielded significantly more m-cresol and m-ethylphenol, indicating that thermodynamic equilibrium was more nearly approached in the system. Increasing the temperature greatly increased the yield of benzenes and naphthalenes, while paraffins, olefins, and total tar acids were reduced. Using oxygen in the carrier gas decreased the yield of low-boiling phenols and increased that of paraffins and olefins at 650° C.

Jan 1, 1966

Major activities of the Bureau of Mines Explosives Research Center during fiscal year 1965 (July 1, 1964, to June 30, 1965) are reviewed briefly. Part 1 summarizes significant accomplishments of the projects that were active during the report period. Part 2 presents short abstracts of the publications that appeared in the Bureau series and in other media during fiscal year 1965. Publications issued after June 30, 1965 are noted where pertinent in footnotes but are not abstracted. ACKNOWLEDGMENTS The Bureau of Mines gratefully acknowledges the support given through cooperative agreements by the following organizations to investigations con¬ducted by the Explosives Research Center during fiscal year 1965: Dow Chemical Company Manufacturing Chemists' Association Monsanto Chemical Company The Sulphur Institute

Jan 1, 1966

By R. T. Sorensen

Research and testing in a small scale equivalent of a commercial flota-tion plant was completed on four low-grade, iron-bearing materials from the western Mesabi range. Closed circuit-flotation of calcium-activated silica with fatty acid collector developed data for comparison with the batch process and highlighted problems not evident from previous bench testing. The four ore samples contained from 27 to 39 percent Fe and were equally represented by nonmagnetic taconite and semitaconite type materials. Iron concentrates containing 6.0 percent, or less, SiO2 were made 5, all four samples. Of the two material types, the semitaconite was the ore amenable to treatment, yielding iron recoveries of about 90 percent as cc pared with 70 to 80 percent for the other. Pilot plant tests showed that concentrate grade made in batch tests could be duplicated in the closed circuit and demonstrated that the amount of recoverable middling iron varied considerably between ore samples. The continuous tests also showed that water temperature strongly influenced results in the treatment of one ore but apparently was of indifferent consequence in another. Progress in thickening and filtration of flotation concentrates was made through introduction of tapioca flour to serve the dual role of iron mineral depressant and flocculant.

Jan 1, 1966

By James S. Browning

Research by the Bureau of Mines demonstrated that organic heavy liquid adhering to or adsorbed on fine mineral particles can be effectively removed by a novel method embracing pulping or displacement washing with hot water alone or in combination with a detergent. Displacement washing with steam alone or in combination with a detergent also was effective for removing the heavy liquid. In tests of sized minus 48-plus 200-mesh mineral charges, both the hot water washing with detergents and detergent steaming effectively reduced the heavy liquid losses on the particles to about 0.2 pound per ton of mineral or less. Centrifuging of the wash solutions permitted an almost complete recovery of heavy liquid from the solution as a pure heavy liquid product.

Jan 1, 1966

By L. B. Pankratz

High-temperature heat contents were measured for two praseodymium oxides and three terbium oxides. There were: Pr2O3 (298° to 1,600° K), PrO1.833 (298° to 1,050° K), Tb2O3 (298° to 1,600° K), TbO1.719 (298° to 880° K), and TbO1.812 (298° to 850° K). With the exception of PrOl.833, all results were regular. PrO1.833 had a small thermal anomaly at 760° K with an extra absorption of 380 cal/mole. The measured heat content values, tabulated smooth heat contents, and entropy increments are reported. Heat content equations were derived.

Jan 1, 1966

By Joseph A. DeCarlo

Coal is one of our basic sources of energy (heat, power, light) and an essential raw material for most metallurgical processing. More than two-thirds of the electricity currently produced by thermal powerplants in the United States is generated by coal, and it is expected that coal will continue to be the major fuel used for this application at least through the 1970's. Coke produced from bituminous coking coal is the principal fuel of iron blast furnaces, and unless ironmaking methods change greatly, coal will continue to maintain a dominant role in iron-ore processing and steel manufacturing for many years. Export markets are expected to increase also, adding to the overall increased demand for coal. Accompanying the increased total requirement, however, will be an ever-increasing demand for higher quality coals, specifically, coals of low sulfur content. Except for special-purpose coals such as those used for the production if coke and ceramics where impurities in the fuel contaminate the end product, the amount of sulfur in coal has been only a minor consideration in the selection of a particular coal for fuel. Major considerations, particularly for the coals used to generate electric power, have been availability and cost. An increased national concern for control of air pollution, however, particularly that resulting from the emission of sulfur oxides in stack gases to the atmosphere, has led to more rigid specifications on coal quality, and the sulfur content of coals will become increasingly more important in the future.

Jan 1, 1966

By H. M. Smith

Data from the Bureau of Mines routine method for the analysis of crude petroleum are used to characterize crude oils. Some data are used directly while other data are used to calculate the aromatic) naphthene) and paraffin contents of the distillation fractions and the correlation index of the paraffin-naphthene portion of the fractions. The calculated properties show significant differences in composition between crude oils. The methods of calculation and interpretation of data are explained and illustrated.

Jan 1, 1966

By P. C. Good

Work was done to determine conditions necessary for efficient electrodeposition of aluminum from fused chloride electrolytes. Aluminum was deposited from a molten chloride salt electrolyte over a temperature range of 150° to 750° C. At lower temperatures in a heat-resistant glass cell, aluminum was deposited on stainless steel and on aluminum cathodes. The deposit was recovered in the form of light, feathery dendrites that could not be consolidated. At 750° C, molten aluminum was deposited at cathode current efficiencies as high as 90 to 100 percent on titanium diboride cathodes and in molten aluminum cathodes. Nitride-bonded silicon carbide was the best cell material, although porcelain was also used. The electrolyte consisted of a mixture of sodium and potassium chlorides in 1 to 1 mole ratio, containing aluminum chloride in concentrations ranging from 2 to 30 weight-percent in cells holding up to 1,000 grams of electrolyte. Generally favorable results were attained in studies made at temperatures greater than the melting point of aluminum.

Jan 1, 1966

By N. H. Coates

The Bureau of Mines determined average film coefficients of heat transfer for helium flowing through smooth, water-cooled tubes at Reynolds numbers of 5,000 to 25,000, helium inlet temperatures of 1,600° to 2,600° F, average temperature difference across the helium film of 800° to 1,300° F, and heat flux to 215,000 Btu/(hr)(sq ft). Since helium was the only gas used, the ranges of values for physical properties of the fluid are limited--thermal conductivity from 0.15 to 0.20 Btu/(hr)(sq ft)(O F/ft), viscosity from 0.082 to 0.104 lb/(ft)(hr), and Prandtl number from 0.63 to 0.68. Four equations, three of them dimensionless, correlate these coefficients with other properties of the helium--bulk temperature, film temperature, dimensionless parameters based on temperature, and the ratio of wall temperature to bulk temperature.

Jan 1, 1966

By R. O. Dannenberg

This Bureau of Mines report describes the results of research to develop a process for recovering additional beryllium from a commercial mill waste product, fluoferrate leach residue. Forty-five percent of the total beryllium in the leach residue was recovered in a beryllia product assaying over 98 pct Be0 by a process comprising (1) leaching with 1 N sulfuric acid, (2) adjusting the acidity of the leach liquor to pH 2, (3) extracting the beryllium with di-2-ethylhexyl phosphoric acid (EHPA), (4) stripping the loaded extract with sodium hydroxide solution, (5) boiling the sodium beryllate strip solution to precipitate beryllium hydroxide, and (6) calcining the beryllium hydroxide. Calculated reagent requirements per pound of Be° recovered by a proposed flowsheet were 28.1 lb sulfuric acid, 0.04 lb flocculent, 0.15 lb EHPA, 0.06 lb isodecanol (IDA), 0.22 gal kerosine, and 6.3 lb sodium hydroxide.

Jan 1, 1966

By Mary S. Esfandiary

This is a revision of a directory of coal research organizations throughout the world that was first published in 1961 as Bureau of Mines Information Circular 8008. Because of the wide acceptance of the first edition, a revision which would supply up-to-date information on coal research and which would facilitate communication among organizations of similar interest seemed important. This compilation includes the names and activities of organizations of various types-government, university, private, and industry. The areas of investigation that each organization is engaged in are indicated in broad terms: Analysis and constitution, mining and geology, preparation, briquetting, combustion, high- and low-temperature carbonization, gasification, conversion to solid and liquid fuels, and health and safety. Publications issued by and describing the work of each organization are cited; almost all of the organizations also publish results of their investigations in the technical press. Selected technical and trade publications that publish information on the science and technology of coal and are not published directly by any of the organizations listed are cited in the pages following the list of organizations in each country.

Jan 1, 1966

By Jr. Norman

The Bureau of Mines investigated the thermoelectric properties of yttrium selenides and tellurides from room temperature to 900° C. X-ray crystallographic data were determined for the yttrium-selenium and yttrium-tellurium compounds that were orthorhombic with a cubic substructure. The yttrium selenides and tellurides exhibited semimetallic to insulator conduction properties with figures of merit of 10-9 to 10-4 °C-1. The mono-selenide and monotelluride behavior was partially degenerate; unsatisfied bonds were the source of the large number of charge carriers. The higher stoichiometry selenide compounds were intrinsic semiconductors) but with high electrical resistivities. A critical defect or impurity ionization energy for carrier activation appeared to exist in the majority of telluride compounds. Mobility and energy band determinations are required to interpret completely the observed effects in most of the compounds studied.

Jan 1, 1966

By F. R. Lee

THE Bureau of Mines was established in July 1910 to conduct research and to establish standards for mining equipment and practices which would conserve human life, natural resources, and property in the mineral industries. Several lists of equipment approved by the Bureau as permissible for use in gassy coal mines have been issued since then. The lists covering all approved equipment except breathing apparatus and explosives have born consolidated into two publications: Bulletin 343. Permissible Equipment Approved to January 1, 1953, and Information Circular 8220, Permissible Mina Equipment Approved By The Bureau of Mines During 1953-62. The, purpose of this publication is to supplement Bulletin 343 and Information Circular 8220 with a listing of permissible equipment approved during 1963 and 1964. The schedule, (standards) under which equipment listed herein have been approved are, as follows (cities and dates of approval and revision are, given in footnotes) : Schedule 2F,3 schedule 6D,4 schedule 7C,5 schedule 8C,6 schedule 9B,7 schedule 10C,8 schedule 12D,9 schedule 22,10 schedule 24,11 schedule 25B,12 schedule 25B,13 schedule 29A,14 schedule 30,15 and schedule 31.16

Jan 1, 1966

By G. E. Johnson

Batch tests of coals and coal-derived materials were made by the Bureau of Mines to determine their effectiveness in removing organic contaminants (COD or chemical oxygen demand, comprising those organic compounds that can be chemically oxidized, and ABS or alkylbenzene sulfonate, common household detergents) from the final effluent of secondary-treated waste waters. The adsorptive capacities of flyashes, coals, including at least one sample of each rank found in this country, pretreated coals, and miscellaneous materials including commercial chars and coke, were determined and compared with that of granular activated carbon. The coals, though not as effective as activated carbon, possess an economic advantage--they are relatively inexpensive, and they can still be burned as fuel without any loss of fuel value after use in waste¬water treatment. A hvcb coal was found to be one of the best, having about one-fourth the capacity of activated carbon for COD, adsorbing about 4 percent of its weight before it became saturated. Several coals contained constituents that added to the COD content of the treated water. Thus knowledge of the performance of the coal is necessary to insure selection of a proper coal as adsorbent.

Jan 1, 1966

By L. B. Pankratzt

The heat capacity of dimo1ybdenum carbide (Mo2C) was measured from 51° to 298° K, and the entropy at 298.15° K was evaluated. Heat content measurements above 298.15° It were conducted for dimolybdenum carbide (M0caY) and monotantalum carbide (TaC). The results were combined with known heats of formation and the 298.15° K entropy for TaC to obtain values of the heat and free energy of formation from 298.15° K to 1,400° K for MoaC and from 298.15°K to 1,800° K for TaC.

Jan 1, 1966

By Walter Kawa

Coals of various rank were reacted by the Bureau of Nines in plasma jets generated from argon and argon-hydrogen mixtures containing up to 33 volume-percent hydrogen. Average plasma temperatures ranged from about 3,400° to 12,000° C. Products were a solid residue and a gas containing hydrogen, methane, acetylene, diacetylene, and oxides of carbon. The highest yield of acetylene obtained with argon plasmas was 15 percent by weight of moisture- and ash-free coal. The data indicated that acetylene yields of 40 percent or higher can be obtained from the reaction of coal in argon-hydrogen plasmas, although results from these experiments could not be correlated with operating variables because of low recoveries plasma contained sufficient energy to heat the coal to temperatures as high 9,000 or 10,000° C, but complete devolatilization did not occur in any experiment.

Jan 1, 1966

By Donald R. Corson

The Bureau of Mines is conducting research on the effects of various established and potential soil-stabilization additives to hydraulic backfill. This initial phase is an evaluation of the effect of inclusion of varying amounts of Portland cement and combinations of cement and a dispersant on the bearing strength of backfill. Results of unconfined compression tests are given for over 200 sample cylinders incorporating a fill material with cement or cement and dispersant. Inclusion of a minor amount of dispersant (0.2 percent by weight) is found to yield a significant increase in strength for 20-to-1 and leaner sand-cement mixes. An apparent optimum concentration of dispersant exists beyond which no further increase in strength is achieved. A dispersant-cement ratio of l.8- to-1 yielded a strength increase of 515 percent over the strength of untreated 40-to-l sand-cement mixes.

Jan 1, 1966

By James F. Devine

The radial, vertical, and transverse components of particle velocity were recorded by Bureau of Mines investigators along gage arrays extending in one or two directions for 145 to 3,170 feet at five quarries. Of the 39 quarry blasts, 12 were instantaneous blasts, 5 were of the one hole per delay type, using millisecond delayed caps, and 22 were multiple hole per delay type employing millisecond delay detonating fuse connectors. Charge weight per hole ranged from 8 to 1,500 pounds, and the charge weight per delay interval, including the instantaneous blasts, ranged from 25 to 4,620 pounds.

Jan 1, 1966

By Martin H. Stanezyk

The Bureau of Mines investigated leaching of selected copper sulfide minerals and a composite of impure flotation concentrates at elevated temperatures and pressures with ammoniacal solutions. Copper 1 (tractions of 96 percent were obtained by leaching chalcopyrite at 75° C under oxidizing conditions for 60 minutes. An extraction of 99 percent of the copper contained in the composite concentrate was obtained by leaching the product for 90 minutes at 75° C. In tests of bornite, chalcocite, and covellite, 90 to 97 percent of the copper was extracted at 20° C provided an 8-hour reaction period was used. At 75° C essentially complete dissolution of the copper from these three minerals was accomplished in 60 minutes. Additions of ammonium sulfate to the leach solutions were required to obtain high-percentage extractions of the copper from bornite, chalcocite, and covellite. Although ammonium sulfate was not required when digesting chalcopyrite, copper extraction was enhanced and less free ammonia was required when ammonium sulfate was added to the leach pulps. The chemistry of leaching copper minerals was studied. It was C, termined that chalcocite altered to covellite as one step in the dissolution When leaching iron-bearing copper sulfides, hydrated iron oxide formed on the mineral surfaces, indicating that a diffusion process prevailed. No evidence of covellite was detected.

Jan 1, 1966