Search Documents

By E. G. King

Many of the existing thermodynamic values for the titanium halides are estimates, including all the entropies and high-temperature heat contents of their crystalline and liquid phases. This report contains the results of low-temperature heat capacity measurents (which lead to entropy values at 298.15° K,) and high-temperature heat-content measurements of four halides - trichloride, tribromide, tetrabromide, and tetraiodide. The new data are combined with selected heat-of-formation values at 298.15° K. to obtain improved values of the heats and free energies of formation of these halides at high temperatures, thus supplementing the previous data of Kelley and Mah.5/ ACKNOWLEDGEMENTS This investigation was conducted under a cooperative arrangement between the Federal Bureau of Mines and the Department of the Navy, Office of Naval Research. The work was done by Bureau of Mines personnel using Bureau of Mines calorimetric equipment. The Office-of Naval Research supplied the supporting funds and arranged for procuring the samples of the titanium halides. The samples were prepared and analyzed by the Inorganic Chemistry Section, Division of Chemistry, National Bureau of Standards.

Jan 1, 1961

By Dale W. Richardson

Ductile hafnium was not obtained consistently by the conventional Kroll process. The bimetal reduction modification produced a more ductile hafnium by lowering the impurities, especially oxygen, in the sponge metal. Hafnium oxide was chlorinated in the presence of carbon to form anhydrous hafnium tetrachloride, which was reduced by sodium and magnesium in an inert atmosphere to produce sponge hafnium metal. After vacuum distillation to remove the byproducts, the sponge was arc-melted into ingot and rolled into strip. Metallic impurities were decreased by evaporating the hafnium tetrachloride from a fused salt. An excessive amount (over 1,200 parts per million (p.p.m.)) of aluminum was contained in some of the hafnium oxide, much of which remained as aluminum chloride in the hafnium tetrachloride during chlorination. Evaporation of the hafnium tetrachloride from a fused NaCI-KCI mixture during the Mg-Na reduction greatly lowered its aluminum content, as most of the aluminum and some of the other metallic impurities were retained by the fused salt.

Jan 1, 1961

By H. S. Caldwell

Molten zinc, condensed from zinc vapor, was used by the Federal Bureau of Mines to leach aluminum from an aluminum-silicon alloy made by carbothermic reduction of silicious aluminum ores. Zinc requirements were minimized by re-fluxing condensed zinc in a low-pressure, Soxhlet-type distillation unit. The minimum ratio of zinc used to aluminum in the crude alloy was approximately 2:1. When the system pressure was reduced from atmospheric pressure to 100 microns or less, the rate of aluminum extraction increased by a factor of 20. Leaching rates were much higher when the zinc vapor was condensed directly on the crude alloy than when molten zinc was passed over the alloy in the absence of appreciable zinc vapors. Observations indicated higher extraction efficiencies from crude alloys containing greater amounts of iron. Complete extraction was obtained with negligible loss of zinc. Assuming complete removal of zinc, the aluminum products will contain 1 to 6 percent silicon and about 0.5 percent iron plus titanium. The leached crude-alloy residue is a highly friable spongelike material containing about 80 percent silicon, several percent iron and titanium, with the remainder aluminum. This extraction method has been patented (Patent 2,810,637) and assigned to the Government. Research and development investigations are continuing at the College Park Metallurgy Research Center.

Jan 1, 1961

By Frank Parrish

THIS REPORT by the Federal Bureau of Mines presents data on water-supply wells used by waterflood operators in North Texas and shows the distribution of permeable source sediments. Averages of well characteristics, including static fluid levels, working fluid levels, net thicknesses, producing rates, and depths, are presented and discussed. Essentially all water used in waterflooding is mineralized water from consolidated sediments. This study is concerned with the geology and distribution of these mineralized source sediments, whereas previous work in this area was predominantly a study of shallow sources of potable water. Tables, isopachous maps, and electric-log cross sections are included to describe the several source aquifers. In general, water-producing capacity increases with depth of the sediments. Wells completed in Cretaceous sediments 82 to 600 feet deep yield 50 to 600 barrels of water daily, whereas those completed in Pennsylvanian sediments 360 to 4,110 feet deep yield 100 to 7,000 barrels daily. Although deeper formations are used where oil and water are produced conjunctively and where large withdrawal rates are required, insufficient well data prevented mapping of deeper formations.

Jan 1, 1961

By H. Kenworthy

The purpose of the study described in this publication is to develop methods for recovering simple master alloys or single metal components from discarded and scrapped S-816 alloy, The Bureau of Mines started this investigation late in 1955 after the need became apparent for a method of reclaiming high-temperature alloys from an ever-increasing accumulation of rejected and wornout jet engine turbine buckets. Laboratory studies showed the following: (1) Pyrometallurgical separations are not selective enough, (2) several methods can be used for effective chemical dissolution of the major constituents of the alloy, (3) a master alloy or complex salts of cobalt and nickel can be separated, (4) chromium, contaminated by several other metals, may be segregated, and (5) more time and effort need to be expended in separating the minor constituents and improving the purity of the major metals removed. Difficult and incomplete chemical separations were attributed to the complexity of alloy composition, as were the long tedious chemical analyses o' products. For determination of several of the metallic components, standard methods of separation and routine analytical procedures had to be considerably modified to achieve satisfactory results. The overall technical problems involved in separating S-816 components do not appear to be insurmountable; however, refinement of several of the methods used in this investigation is desirable.

Jan 1, 1961

By Thomas C. Atchison

The experimental work described in this report is part of a continuing study by the Federal Bureau of Mines of the fundamental physical processes involved in breaking rock with explosives. Six explosives were tested for their strain-producing abilities in a dolomitic marble. The explosives selected for testing had a tenfold variation in detonation pressure and a fivefold variation in characteristic impedance (product of loading density and rate of detonation). Strain pulses produced by the detonation of small charges of the explosives were recorded at distances of 5 to 130 feet. Peak strain, ?, was found to decrease with distance, R, in accordance with an exponential propagation law previously determined for other rock types, namely ? = (K/R)e ?aR The absorption constant, a, did not vary significantly with the explosive and was of the same order of magnitude as that for other rock types. The different explosives produced a fivefold variation in the value of the intercept constant, K.

Jan 1, 1961

By Maurice J. Peterson

The applications of optical spectrochemical methods of analysis for determining trace impurities in metals are described, and the need for developing analytical procedures capable of accurately determining fractional parts per million of impurity elements in metals is stressed. Factors which determine sensitivity of detection and means to extend sensitivity levels in spectrochemical methods are discussed. Examples from the current literature illustrate the diversity of spectrochemical techniques that have been applied to the analyses of varied sample types, Many of the methods use preconcentration procedures to increase sensitivity limits. A bibliography containing abstracts of recent methods in included. Optical spectrochemical analysis is based upon the measurement of radiant energy emitted by atoms of the elements to be determined when a sample is subjected to a suitable source of excitation. The behavior of the valence electrons during excitation, usually by an arc, spark, or flame, produces radiant energy of specific wavelengths. This is recorded as spectral line images on a photographic film or plate by the spectrograph; for direct-reading instruments, the spectral lines are detected with photomultiplier tubes. The spectral lines result from the excitation of atoms in the sample. Each variety of atom produces its own characteristic set of lines, thus serving to identify the elements in the sample. Increased concentrations of elements in the excited sample results in increased blackening of the spectral line images.

Jan 1, 1961

By M. I. Copeland

The investigation of the zirconium-gadolinium equilibrium diagram was part of a program to investigate rare:earth alloys for use as nuclear reactor control materials. Investigation of the zirconium-gadolinium equilibrium diagram revealed a eutectic system with limited terminal solubilities and one peritectoid reaction. The eutectic composition occurs at about 82 percent gadolinium, and the eutectic isotherm, which occurs at 1,220 ±5° C., extends from about 12 to 99+ percent gadolinium. A peritectoid isotherm occurs at 890 ±5° C. and extends from about 2 to 99+ percent gadolinium. The solubility of gadolinium in beta zirconium decreases from about 12 percent at 1,220 ±5° C. to about 2 percent at 890 ±5° C. The solubility of gadolinium in alpha zirconium decreases from approximately 5 percent at 890 ±5° C. to between 2 and 3 percent at 600° C. Vary little solubility of zirconium in gadolinium was indicated. An allotropic transformation of gadolinium was observed at 1,260 ±5° C. A change of the gadolinium transformation temperature on alloying with zirconium was not observed.

Jan 1, 1961

By David M. Gullikson

As part of its program of petroleum production research the Federal Bureau of Mines has long been engaged in the study and development of systems of analysis of oilfield waters (8, 12, 20, 21, 22, 27, 30).21 However, many of the early chemical procedures developed by the Bureau and widely adopted by the petroleum industry are time consuming, and some are unreliable for determining certain constituents found in California oilfield waters. Because of the need for more rapid and more accurate methods having greater sensitivity with low concentrations of some constituents, a study has been made by the Bureau's Petroleum Research Laboratory at San Francisco, in developing new techniques and modifying previously published techniques for analyzing oilfield waters by flame spectrophotometric, potentiometric, and colorimetric methods. Test solutions were synthesized for testing the suitability and accuracy of the procedures, and the effect of interfering ions. These solutions contained known quantities of characteristic constituents of oilfield waters including sodium, magnesium, potassium, calcium, lithium, strontium, barium, sulfate, chloride, bromide, iodide, carbonate, bicarbonate and borates in a wide range of concentrations. The compositions of these synthetic brines are listed in table 22. Many California oilfield waters contain salts of petroleum-derived organic acids and several synthetic oilfield waters also were prepared to which large quantities of naphthenates or salts of petroleum acids were added.

Jan 1, 1961

By J. P. Capp

The Federal Bureau of Mines and the Alabama Power Company conducted an experiment in underground gasification of coal at Gorgas, Ala. involving the use of hydraulic fracturing to increase the air acceptance of a coalbed for the introduction of combustion air and removal of product gases. Air acceptance is defined as the flow rate of air which can be injected into the coalbed at 65 p.s.i.g. This was the second time the hydraulic-fracturing technique was used at Gorgas. Sand suspended in a heavy oil served as the fracturing fluid in the first experiment; in the second the sand was two to six times larger and was suspended in a water-starch gel. In addition to providing further tests of the underground-gasification process, the purpose of the second experiment was to determine the effects of the larger sand and greater volumes of a water-base fluid on (1) the extent of the fractured area, (2) the air acceptance of the coal, and (3) the rate at which a gasification path could be carbonized (linked) through the coal, and to compare these results with those of the first experiment. The coal was fractured by injecting 11,000 lb. of sand and 33,580 gal. of water and water-gel at 200 to 600 g.p.m. and 900 to 1,000 p.s.i. The fluid fractured the coal and the sand served as a propping agent to hold the cracks and crevices open. Pressures during the fracturing operation at test boreholes indicated that the fracturing fluid extended only about 150 ft. from borehole H, the point of application of the fracture. Injection of air revealed that the air acceptance of the coalbed within this e t was materially increased. On the other hand, increased air acceptance also was noted at boreholes up to 280 ft. from borehole H and at the electrolinking area 300 to 400 ft. away, indicating that the fracture effects extended considerably farther than was evident from observation. Similar effects were noted at approximately the same distances after the first hydraulic fracture.

Jan 1, 1961

By Murray Jacobson

Data obtained by the Federal Bureau of Mines on the dust explosion hazard in air are presented for 220 samples of agricultural products. Information is given on ignition temperature of dust clouds and layers, minimum explosive concentration, minimum electrical energy for ignition, explosion pressure and rates of pressure rise, amount of inert dust required to prevent flame propagation, and, in a few instances, the permissible oxygen concentration in an atmosphere to prevent ignition by spark and by heated surface. The effects of particle size and source of sample on explosibility are shown. The relative ignition sensitivity, severity of explosion, and overall explosibility of the materials are characterized by empirical indexes. This report contains Ma obtained by the Bureau in laboratory studies on the explosion hazards of agricultural dusts. Recognition of the dangers will encourage adoption of adequate measures to prevent ignition and explosion during preparation, processing, and utilization of the materials. Agricultural products constitute one of the largest groups of materials used in America. More than 260 million tons of various grains, much of which now exists in dust form, was grown in 1958.6/ Over 600,000 tons of the annual production of 200

Jan 1, 1961

By W. L. Hunter

The research on this report was conducted to obtain information on the feasibility of producing ferro chromium of varying silicon and carbon contents from domestic chromite. Concentrates from the Mouat deposit were chosen because they typify the chromite found in the Stillwater complex, the largest domestic reserve, and are similar in composition to other extensive North American and foreign deposits. Batch-smelting tests designed to produce high-, medium-, and low-carbon ferrochromium were made in single phase and three-phase, electric-arc, steelmaking furnaces. Agglomeration studies were made in a rotary kiln. Continuous smelting tests were made to yield data on the production of high-carbon ferro chromium and low-carbon ferrochromium-silicon. The carbon content of high-carbon ferrochromium was lowered to the medium-carbon range by oxygen injection. Mouat stockpile concentrates were nodulized in a gas-fired rotary kiln using quartz, limestone, and fluorspar additions in the proportion necessary to flux the slag. The nodules were smelted in a continuous test using coal, coal char, and mixtures of the two consecutively as reductants.

Jan 1, 1961

By Eugene T. Sheridan

The Bureau of Mines annually canvasses the fuel-briquet and packaged-fuel producers in the United States and publishes economic data on these industries, based upon reports submitted voluntarily by producers. This publication lists all producers that reported commercial production to the Bureau for 1960 and presents data on individual plants. The companies named herein represent virtually all producers of processed minerals fuels. A few small plants may not have been canvassed or failed to respond to the survey because some of the smaller plants operate intermittently and the survey is voluntary. All plants that reported commercial production were included; regardless of size. Specifically excluded were plants that manufactured briquets from wood charcoal. Fuel briquets and packaged fuel are manufactured solid fuels, produced by mixing fine-sized mineral fuels with binding materials and compressing into small individual shapes, Briquets are produced in pillow-shaped and cylindrical form, are 2 to 4 inches long, and weigh 2 to 4 ounces. Packaged fuel consists of 3- or 4-inch cubes; 6 or 8 of which are wrapped together in heavy kraft paper to form a package weighing 10 to 15 pounds, Briquets are durable and may be stored and handled as bulk fuel; packaged fuel breaks easily and must be stored indoors to prevent it from deteriorating. Whereas briquets are consumed in many areas as a general residential fuel, packaged fuel is more of a specialty item, used at times to supplement other fuels. Packaged fuel is burned without re-moving the paper and is referred to as the "white glove" fuel.

Jan 1, 1961

By F. W. Wessel

Manganiferous carbonate slates of the Cuyuna range, which are part of the unoxidized thin-budded iron formation, represent a large potential source of manganese. This report details recent bench-scale research by the Federal Bureau of Mines in applying mineral-dressing techniques to these materials in order to investigate their potential uses. Work outlined in the report was directed toward the production of concentrates usable as iron-blast furnace feed, but an equally important objective might have been to furnish an enriched feed for extractive processes for recovering manganese. Flotation concentrates were prepared that contained 11.1 percent manganese, 27.8 percent iron, and 12.2 percent silica, with recoveries of 73 percent of the manganese and 48 percent of the iron. Calculated analysis for a simulated sinter suggests a product containing 16.0 percent manganese, 40.2 percent iron, and 17.6 percent silica, with 31 percent recovery of the dry weight of the ore. The silica in the flotation concentrates was due to quartz and iron silicates. Substantial quantities of the iron silicates (stilpnomelane and smaller amounts of minnesotaite) were present in the slate, and the need to reject these minerals limited the recovery of iron. The sintered flotation concentrate would be usable as ferruginous manganese ore for iron blast-furnace feed because of its favorable manganese silica ratio. The unsintered flotation concentrates, representing 45 percent of the feed weight and containing manganese enriched in the ratio of 1.6 : 1, also could be used as feed to processes for extracting manganese.

Jan 1, 1961

By W. M. Deaton

The Keyes Helium Plant of the Federal Bureau of Mines was constructed under an expedited schedule, to supply the urgent and growing demand for helium in atomic energy, missiles, aerology, space exploration, shielded-arc welding, and low-temperature research. Construction began in December 1958 and ended in August 1959. The plant, near Keyes, Okla., processes 2 percent helium-bearing natural gas from the Keyes gasfield. In 1960 the plant produced and shipped 263 million cubic feet of helium (equivalent to an annual rate of 290 million cubic feet). Production cost was $9.11 a thousand cubic feet of helium. A low-temperature process involving two steps is used; the first separates a crude-helium product from the natural gas at about -250° F. and 225 pounds per square inch gage (p.s.i.g.); and the second purifies the crude helium to a high-purity product (Grade-A helium, 99.995 percent helium) at about -320° F. and 2,750 p.s.i.g.

Jan 1, 1961

By James S. Browning

The purpose of this investigation was to develop a dependable and economic method for recovering spodumene and mica from pegmatites of the type found in Gaston County, N. C. Laboratory batch tests and continuous flotation tests were made by the Federal Bureau of Mines to determine the feasibility of treating the ore by flotation to recover high-grade spodumene and mica concentrates. The spodumene flotation circuit yielded concentrates containing 6.50 percent lithia (Li20), with an overall recovery of 81.8 percent of the lithia in the ore, The mica circuit yielded concentrates containing 97.5 percent mica, with a recovery of 82.5 percent of the mica in the spodumene tailing.

Jan 1, 1961

By J. D. Ramsdell

The object of this investigation by the Federal Bureau of Mines was to evaluate the workability, recrystallization characteristics, and mechanical and physical properties of high-purity electrorefined vanadium. The low level of interstitially soluble elements in electrorefined vanadium results in a soft ductile metal which responds readily to cold working by rolling, swaging, and press-forging. Hardness, strength, and resistivity increased with an increase in impurity content, but thermal expansion was independent of impurity content. The work-hardening of vanadium occurs rapidly. Most of the hardness increase occurs in the first 15 pct. of reduction in area. When vanadium is annealed, its hardness increases to a maximum when the annealing temperature is between 200° to 400° C. A sharp decrease in hardness develops as the annealing temperature is increased. An anomaly in the hardness versus annealing temperature curve is present in the 600° to 800° C. range, while all evidence of cold-work is removed at annealing temperatures above 900° C.

Jan 1, 1961

By Scott W. Hazen

In recent years many mining companies have recognized that their chance for continued economic survival depends on the adaptation of technological advances in their operations. Increased productivity through new developments in mining methods and improvements in equipment has made mining and processing of lower grade ores possible. Cost analysis has produced accurate data on the costs for development, production, and processing of ore. All of these changes and cost studies have shown the necessity for increased accuracy in determining the grade of ore. Methods of estimating grade in a mineral deposit have not kept pace with the technological advances in the other areas. The same methods are in use today as in the past. Experience and judgment are major criteria of accuracy and the results are highly subjective. In 1953, as part of its research program to develop a better understanding of fundamentals of mining technology, the Federal Bureau of Mines began a sampling method research project at its Denver Mining Research Center. The basic objective of the project is to investigate sampling methods and to study the adaptation of the techniques of statistical analysis to mine sampling.

Jan 1, 1961

By R. M. Becker

As part of the Bureau of Mines program for examining the Nation's iron and titanium resources, magnetic, gravity, and geologic surveys were made to permit an estimate of the extent and magnitude of the Iron Mountain, Colorado, titaniferous magnetite deposit. Gabbro is the dominant rock type of the area. Within the gabbro are lenses of titaniferous magnetite, 5 to 25 feet wide and as much as several hundred feet long. These lenses comprise a zone which has scattered occurrences of magnetite for 2,200 feet. To the west, the gabbro grades into a strip of pyroxenite that in turn borders a large monzonite mass. A wedgelike broadening of the pyroxenite with depth accompanied by little or no increase in the titaniferous magnetite is considered a reasonable interpretation of the field data. The iron deposits appear to be limited and discontinuous.

Jan 1, 1961

By J. W. Town

This report summarizes the results of laboratory investigations conducted by the Federal Bureau of Mines to obtain hydrometallurgical information on the dissolution of mercury sulfides from ores, flotation concentrates, and pure mercuric sulfides. Statistical methods were used to design the experiments and evaluate the resulting data. Studies demonstrated that cinnabar is readily soluble in sodium sulfide, partly soluble in potassium sulfide, and essentially insoluble in ammonium sulfide. Additions of sodium hydroxide or potassium hydroxide to sodium sulfide solutions increased mercury extraction slightly; when either was added to potassium sulfide or ammonium sulfide solutions, mercury extraction was equal to that of sodium sulfide. Tests at the Albany Metallurgy Research Center showed that sodium sulfide would completely dissolve chemically pure mercuric sulfide, more than 95 percent of the cinnabar in 5-percent mercury flotation concentrates, and 60 to 90 percent of the cinnabar in low-grade ores. The double-leach tests showed that potassium sulfide would dissolve over 90 percent of the arsenic in mercury-arsenic products and 1 to 10 percent of the mercury; then sodium sulfide-hydroxide solutions would dissolve 80 to 90 percent of the remaining mercury and 5 to 10 percent of the arsenic.

Jan 1, 1961