Search Documents

By T. E. Gray

This report describes the preparation characteristics of the most significant coal beds in Wise County, Va. It is one in a series of reports planned to determine coals suitable for the production of metallurgical coke, either as mined or after beneficiation. Wise County produced approximately 6,600,000 tons of coal in 1955, of which about 2,110,000 tons was cleaned mechanically. The Federal Geological Survey has estimated that 1,341 million tons of measured and indicated coal reserves remained in the county as of January 1, 1951.

Jan 1, 1958

By R. D. Joseph

This report deals exclusively with roof-fall accidents that occurred during 1955 and 1956 in both anthracite and bituminous-coal mines throughout the United States. The report stems from a cooperative study conducted by the Bureau of Mines and the Roof-Control Committee of the Coal-Mining Section, National Safety Council. The study includes an analysis of individual accident reports, sets forth the measurable factors, and compares such factors with a representative sample of average data from 39 anthracite mines and 117 bituminous mines (appendixes A and B). Particular emphasis is placed on fatal roof-fall accidents with respect to their causes, locations, and the methods of support used at the point of occurrence. INTRODUCTION The purpose of the report is to classify all measurable details of the occurrences of roof-fall fatalities so that the material presented will assist those promoting safety and will serve as a manual for those whose principal duty is inspection of mines.

Jan 1, 1958

By James Westfield

Uranium activity has introduced a comparatively new hazard to United States mining. In addition to the hazards common to all mines, uranium mines have a complex health problem of radiation damage. Like many new processes, radiation and nuclear energy can be made to serve man in many useful ways when properly understood and handled; but, like fire, gases, and electricity, their potential dangers must be known and respected, and appropriate precautions must be taken or death may result. Since 1950 the Public Health Service has been conducting basic investigations on exposure to radon and its daughter products and the effect of exposure upon the health of miners in uranium mines of the Western States. The Bureau of Mines assisted in several of these investigations, especially in mines on Indian lands. The studies have shown that a serious health hazard exists from radioactive exposure that might cause lung cancer if continued over a number of years. The Public Health Service report, Control of Radon and Daughters in Uranium Mines and Calculations on Biologic Effects,6/ shows that 55 percent of the uranium mines employing 64 percent of the miners had atmospheric concentrations more than five times the working level now accepted as reasonably safe for industrial exposures. Extensive control measures are necessary to reduce these concentrations to the suggested working level of less than 300 micromicrocuries of total radon daughter products per liter of air.

Jan 1, 1958

By Roy F. Abernethy

All samples tested showed some loss of heating value for the 5-month period under all 4 storage conditions. The losses increased as the time of storage increased, with the pan-storage samples showing somewhat greater losses than those in cans. The individual daily analyses for the first 2 weeks and the analyses every other day for the third and fourth weeks of storage vary within the approximate tolerance of the test for heating value. During the first 2 months of storage the changes in heating values were not Significant for the samples from Pennsylvania, Indiana, and Colorado. The Ohio coal indicated some loss by the end of I month, which increased to a value measurable with certainty by the end of 2 months. These data show that (1) small changes may occur even to samples in closed cans and (2) the laboratory sample should be handled as expeditiously as is practical until the analysis is completed. The statement by the ASTM that "If the B.t.u. determination is an important consideration in the sale of coal, the time elapsed between sampling and analysis shall not exceed 30 days,"3/ is quite adequate for 3 of the 4 coals tested. The change in the Ohio coal stored for 30 days is merely indicated and could not be determined with certainty by the techniques normally employed. The data on free-swelling indexes determined on can samples, after 30° C. air drying, show that only the Indiana coal lost more than one unit in free-swelling index number in 120 days. No significant changes were observed with the samples from Pennsylvania, Ohio, and Colorado in the 5-month period.

Jan 1, 1958

By W. O. Philbrook

Reduced-scale models have long been used in hydrodynamics, aerodynamics, and heat transfer for studying fundamental flow relations or the performance of prototype designs under prescribed conditions. The pilot plant is a common tool of chemical engineering for investigating process variables and as an integral step in developing a new process. The metallurgical industry was rather slow to recognize the applicability of these techniques to some of its established and rather complex processes, but there has been a rapidly increasing number of applications of the principles of modeling in process metallurgy since World War II. Not only have pilot-scale operations been employed for developing methods of extracting metals that have recently achieved commercial importance, as well as new processes for some of the commoner metals, but models have also been used for engineering studies aimed at better understanding of the controlling, variables of time-honored conventional processes, It appears that the principles of similitude have become accepted as a useful tool, when properly applied, in metallurgy as in other fields of engineering. Much of the work of the Pyrometallurgical Laboratory, Region V, involves study of high-temperature smelting and refining processes for ferrous and related metals in pilot-scale equipment, such as the experimental blast furnace, converter, open-hearth, arc furnace, and rotary kiln. It was appropriate for the work of this laboratory that guiding principles for designing apparatus and interpreting results should be set down and that a bibliography of related work should be available for reference. A summary of the principles of model study and a brief review of some of the more noteworthy general papers have been published elsewhere.3/ Also, the Bureau of mines plans to publish a report of investigations describing its experimental work in this field. The bibliography is presented here as a service to others who may have use for it.

Jan 1, 1958

By F. W. Smith

To determine whether preheating coals before carbonization would improve the coking properties of the coals, particularly the weaker coking coals, 3 coals, 1 each from Illinois, Kentucky, and Pennsylvania, and a blend of the Illinois with a Pocahontas coal were preheated before testing for coking properties in the Bureau's BM-AGA pilot oven. The effects of preheating on the chemical and physical proper-ties of the coals and on the yields of carbonization products and strength of the coke produced from the preheated coals were determined, as were also the effects of bulk density, gaseous atmosphere, and residence time during preheating. Most benefit from preheating was found with weaker or oxidized coking coals, whereas the more strongly coking coals and blends showed little effect. Direct charging of preheated coal to the coke oven without cooling gave better coke, increased yield of tar, and decreased yield of gas. INTRODUCTION Although 94 percent of today's coal production comes from fields east of the Mississippi, the Eastern States have only about one-third of the Nation's recoverable reserves. West Virginia, which now produces more than any other State, has much smaller reserves than Utah, Colorado, and Wyoming.5/ However, the manufacture of iron and steel in Western States, which has increased greatly since World War I, is handicapped by the scarcity of high-grade coking coals, such as are plentiful in the Appalachian region. Unless a practical method of improving the cokemaking property of local coals is developed, ferrous metallurgical industries in the West must continue to use inferior coking coals and to pay high shipping charges for better coals.

Jan 1, 1958

By Oliver Bowles

The term "stone" in its broader sense includes not only the well-known limestone, marble, granite, sandstone, and slate but also precious and semi precious stones and many minerals and rocks not included in the principal groups. Stones have long been used for structural and ornamental purposes. To be so used, they must be cut to various shapes and sizes, and some must be polished to bring out their inherent attractiveness.

Jan 1, 1958

By W. H. Ode

In 1949 the Coal Committee of the Economic Commission for Europe, Geneva, Switzerland, established a Classification Working Party, to develop an international system for classifying coal. This project was necessitated by the increased trade in coal among various nations following World War II. Although national classification systems existed, they had been developed to cover the characteristics of domestic coals without reference to coals of other countries. Different terms for describing similar or identical coals in each nation caused confusion in evaluating coals shipped in international trade. Experts from Austria, Belgium, Bulgaria, Czechoslovakia, Denmark, the Federal Republic of Germany, France, Greece, Hungary, Italy, the Netherlands, Poland, Sweden, the Union of Soviet Socialist Republics, East Germany, the United Kingdom, the United States of America, and Yugoslavia participated in various stages of the classification work. Walter A. Selvig was appointed by the Bureau of Mines as the technical expert to represent the United States because of his experience in developing and standardizing methods of analyzing and classifying American coals. He served on the Classification Working Party until his retirement from the Bureau of Mines early in 1956. Extensive laboratory work was done in connection with the classification studies at the Pittsburgh Experiment Station of the Bureau of Mines.

Jan 1, 1958

By L. Nahai

In two decades Turkey has emerged from the debacle of the Ottoman Empire to become one of the most modern nations in the Middle East. The numerous achievements of this period were remarkable in that they affected human and social, as well as economic, fields. Most of this progress was achieved by Turkey's unaided efforts and the utilization of domestic resources; however, since 1948 various United States aid programs3/ have made significant contributions to increased agricultural and industrial output. Turkey's singleness of purpose in favor of a strong, independent, and prosperous republic has evoked universal admiration and encouraged the hope of stability in the Middle East. Much of the development of the Turkish economy to date has been fostered by the State; however, with growing strength the leaders in 1950 considered the time appro¬priate to relax the nationalistic economic policy and permit private enterprise to play a larger role in increasing domestic output and raising the tempo of industrialization. In pursuance! Of this policy, laws encouraging investment of foreign capital in Turkey and others stimulating development of mining and petroleum enterprises were enacted in 1954. This new legislation, plus the cooperative attitude of the Turkish Government, have encouraged wide interest in the mineral resources of the country.

Jan 1, 1958

By Henry P. Chandler

COMBINED sales of abrasive materials in the United States during 1956 increased at about the same rate as the value of the Gross National Product in terms of 1954 dollars,3 which was nearly 3 percent. However, some segments of the industry did not follow the general pattern. Sales of abrasive grinding wheels increased 9 percent in value. Sales of surface-coated abrasives declined 5 percent in quantity hut increased 1 percent in value, Production of crude silicon carbide in the United States and Canada advanced both in tonnage and value, but that of abrasive-grade [ ]

Jan 1, 1958

By C. H. Riggs

THIS REPORT give's the results of a study of the central and south parts of the Cushing oilfield, including a description of the geology, a review of the production history, and estimates of oil reserves available by secondary-recovery methods. Each of the major producing zones of the field is treated separately. The report, which is one of a long series of field studies the Bureau of Mines has conducted over the past 40 years, was prepared to aid operators to increase oil recovery and to help prevent underground waste in the Cushing field, in the State of Oklahoma, and in the United States. The geology and production history are presented not as a review of past behavior of the Cushing field but rather to interpret the possibilities for increased oil recovery by future development of this and similar areas. The field, which is in the northwest corner of Creek County, Okla., was discovered in 1912 and developed during 1913 and 1914. For several years it, was one of the most important areas producing high-grade crude oil in Oklahoma. Although some oil has been recovered from each of 10 separate reservoirs, nearly 98 percent of the total recovery of oil in the area studied was from 4 major producing formations (table 1). Of these, only the Bartlesville [ ]

Jan 1, 1958

By S. H. Lorain

Tin mining on Seward Peninsula, Alaska, has been intermittently active since the early 1900's. Most of the recorded production (over 2,200 short tons of metallic tin) has been obtained from placer deposits, but recent production also has resulted from development of lode deposits associated with intrusive rocks occurring in the western part of the peninsula. Generally, the lode deposits containing tin minerals (principally cassiterite) are found in dikes, in granite masses, and in silicate zones in limestone overlying the granite. Both the placer and lode deposits have been of considerable strategic interest to the Government because of the almost total absence of a domestic supply of tin. The most important tin-lode deposit discovered to date is in the Cassiterite dike at the Lost River mine, on Cassiterite Creek about 85 miles northwest of Nome. This highly altered, rhyolite porphyry dike averages 12 feet in thickness, strikes N. 75° to 85° E., and dips steeply to the south; it can be traced on the surface for about 8,000 feet. Throughout its explored length of about 2,200 feet the dike everywhere contains some tin and tungsten in veinlets and disseminations; economic concentration of the are minerals, however, is confined to definite shoots. The ore minerals include cassiterite, stannite, hulsite, paigeite, wolframite, scheelite, and base-metal sulfides; gangue minerals include fluorite, boron silicates, and lithium-bearing minerals. Some ore minerals also occur in the numerous other dikes and in the granite and intruded limestone in and adjacent to the mine.

Jan 1, 1958

By E. P. Carman

1. CARMAN, EVERETT P., OPPERMAN, MARTHA, NISHIYANA, SALLY, AND RACOOSIN, LEE. Bibliography of Bureau of Mines Investigations of Coal and Its Products, 1945 to 1950. B. 528, 1954, 60 pp. 40 cents. 2. ROSE, HAROLD J. Industry-Sponsored Coal Research in the United States. Chap. in Proceedings: Fifth International Conference of Directors of Mine Safety Research. B. 489, 1950, pp. 9-12. $1.25. Minerals Yearbook 3. STRINER, HERBERT E., CARMAN, E. P., AND GOODING, RICHARD M. Review of the Mineral-Fuel Industries in 1952. Minerals Yearbook 1952, Fuels, vol. 2 (pub. 1954), pp. 1-28.

Jan 1, 1958

The original manuscript of section 2 of this series of miners' circulars devoted to accident prevention in bituminous-coal mines was completed in September 1944. At that time roof bolting had been tried with some success in the lead-mining district of south-eastern Missouri, but information on the subject was so fragmentary that it was not included as a method of roof support. References to roof support in bituminous-coal mines, therefore, were confined almost entirely to conventional timbering methods. In 1947 the Bureau instituted a research program and intensive study of the general problem of roof control, which emphasized roof-bolt application. The rapid increase in mechanized mining following the close of World War II provided the impetus for the Bureau's roof-control investigations, because the vertical supports used with conventional timber restricted the maneuverability of mechanical face equipment, and the industry wanted to explore every possible method of eliminating interference with the production cycle to gain full advantage of mechanized mining. Moreover, the accidental dislodgment of vertical supports greatly increased the roof-fall hazard. As roof falls have killed and seriously injured more mine workmen every year than any other cause or classification of injury since records have been kept, the Bureau assumed this investigative leadership with the prime objective of substantially reducing the annual toll from falls of roof, including falls of rib and face.

Jan 1, 1958

By Avery H. Reed

RECORD production of cement, clays, salt, sand and gravel, and stone highlighted the mineral industry of the State in 1956. Coal and iron-ore production declined owing to increased imports of foreign iron ore and decreased demand for metallurgical coke. Alabama ranked second in production of bauxite and of native asphalt, and third in output of iron ore. New developments in the State included the Citronelle oilfield and its 97 wells, which more than doubled the total production of petroleum compared with 1955. There is no question about the impetus that field has given to the oil and gas industry in Alabama, now 13 years old. The State's 4 oilfields are in southwest Alabama and its 1 gasfield is in Marion County, in the Warrior coal basin.

Jan 1, 1958

By Eleanor Abshire

This bibliography is the second in a series that covers the current technical literature relating to the metallurgy of zirconium. The rapid advance in zirconium technology makes it mandatory that abstracts be prepared and compiled as soon as possible to have maximum value; therefore, the information in this volume is not arranged chronologically. As a service to research and production groups, succeeding bibliographies will be issued as new acquisitions accumulate in the Zirconium Information Center sponsored by the Department of the Navy, Bureau of Ships and the Bureau of Mines at the Bureau's Northwest Electrodevelopment Laboratory, Albany, Oreg. The initial volume, Information Circular 7771, Bibliography of Zirconium, covering 969 abstracted reports and 645 United States and foreign patents, was published in April 1957.

Jan 1, 1958

By Alvin Kaufman

Increased exploration in Alaska has resulted in many requests to the Bureau of Mines for facts about the mineral resources and mining conditions in the Territory. This report presents information about the minerals of Southeastern Alaska and the factors that affect development of a mining industry in that area. Southeastern Alaska is a narrow coastal strip of rugged mountains and many islands. The climate is mild, with an average annual temperature of 40° and heavy rainfall. Geologically, the region is favorable for deposition of ore; geographic-ally, it is difficult to prospect and to develop, except along areas immediately adjacent to the coastline.

Jan 1, 1958

By E. W. Parsons

Permanent support of the back is an important economic factor in maintaining a tunnel or other underground opening in condition to render the service for which it was driven. Timber has been most commonly used for support in tunneling and drifting because of its strength and ease of installation. Even when treated for decay, however, timber is subject to deterioration and, over a long period of time, should not be considered a permanent support. Concrete support or lining is permanent and has been used in tunnels of every size for many years but has been almost exclusively cast in place, a difficult, costly process. This report deals with the design and installation of precast concrete supports to combine the best features of both methods.

Jan 1, 1958

By Irving Hartmann, John Nagy, Donald Mitchell

"SUMMARY AND CONCLUSIONThe test data indicate that water infusion of the Pittsburgh coal seam does not reduce the amount of fine dust produced during mining operations to the extent reported elsewhere. Wide variations in the amounts of dust collected in the air current were noted in duplicate samples and repetitive tests. Changes in depth and location of the infusion holes and amount of water injected and addition of a wetting agent to the water had little effect on the amount of dust liberated.Water was forced readily into the coal. Some water flowed out along the cleats, but an appreciable amount remained in the seam. Little or no water pene¬trated the coal seam above the upper infusion holes.The average dust concentration (with and without infusion) in the return air, 40 feet outby the working face, was 25 million particles per cubic foot during undercutting, 20 million during drilling, 75 million during shot firing, and 20 million during hand loading. At the working face the average concentration was 3 to 6 times higher. The concentrations were measured at an airflow of 1,600 cubic feet per minute (c.f.m.) at the face.On the basis of this short investigation, no final conclusions can be made on the effectiveness of water infusion in reducing the amount of fine dust liberated during mining in the Pittsburgh coal seam. However, the data indicate that dust reduction resulting from infusion would be small.INTRODUCTIONThe production of fine coal dust is an inherent part of nearly every phase of mining. The use of large, high-speed continuous-mining machines and other mechanical equipment has increased dust production. In addition, in coal seams that have been subjected to high pressures for a long period, and particularly in dry and friable seams, some very fine dust is in the seam before mining. Much effort has been devoted to allaying and collecting at its source the fine coal dust released during mining. One of the comparatively recent techniques that has been developed for this purpose is infusion of water or other liquids into the coal seam. This method consists of injecting water under pressure into a coal seam to neutralize the fine dust released during mining. The water generally is introduced through bore holes in the face before undercutting."

Jul 1, 1957

By Sidney Katell, JOHN H. FABER, BRYCE L. MADDOX

The information abstracted from the various publications appeared in the magazines under such headings as Business and Industry , Chemical Engineering Developments , Companies in the News , Headlines of the Month , Industrial News , Industry , Refining and Gas - Processing News , Refining News , What's Happening , and others . Although most items are related to chemical and petroleum plants , a few pertain to related fields , such as markets , drilling costs for petroleum , and field prices of crude oil . Certain articles discuss various aspects of cost -estimating procedures or description of processes . Cost bibliographies prepared by other groups are discussed in items 70 and 271. The two references can be considered as supplemental to this report , since the amount of overlap in the contents is insignificant .

Jun 15, 1957