Search Documents

By M. L. Skow

Large tonnages of the manganese ores found in Aroostook County, Maine, are refractory to conventional mineral-dressing techniques and to the common chemical- extraction procedures. The Maple Mountain-Hovey Mountain ores are typical of this type. Because the most promising method of recovering the manganese from these ores has been a chloridizing roast in which the ground ore is in contact with gaseous hydrogen chloride, preliminary batch tests were made with a fluidized bed. On the basis of these tests, it was concluded that fluidization, with careful control of operating conditions, could be employed for this cloridization and warrants further study. Selective volatilization of the iron at 600° C. was unsuccessful. An operating temperature of approximately 950° C. was necessary for a practicable rate of volatilization of manganese chloride. Hydrogen chloride contents of 10 to 100 percent of the fluidized gas gave essentially equivalent manganese recoveries with an 80- minute retention time, For shorter periods reaction was more complete with the higher hydrogen chloride concentrations. At the 80-minute retention period the lower hydrogen chloride concentrations volatilized somewhat less iron and also improved the physical operation of the process. Fluidization gave results superior to comparable tests on chloridization in a fixed bed.

Jan 1, 1956

By Lloyd Williams

1. Reserves have been estimated for three coal beds in Bledsoe County, Tenn.: Morgan Springs, Lantana, and Sewanee. The Richland and Nelson beds occur in Bledsoe County also, but there was not enough information on them for making an estimate of reserves. 2. Known measured and indicated reserves for all beds, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated at 43 million tons as of January 1, 1954. Of this total, 22 million tons represents coal 28 inches and more thick. Areas in the beds were omitted from the estimate because available data relative to the bed characteristics were insufficient for making an estimate conforming with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves deter-mined by this investigation.

Jan 1, 1956

By Ralph H. Whaite

To assist the anthracite industry obtain technical data on pneumatic packing, the Federal Bureau of Mines imported a pneumatic packing machine from Germany and installed it in a mine of a cooperating company in the Northern anthracite field of Pennsylvania. This report covers the second in a series of experiments in applying pneumatic packing for controlling strata movement (subsidence) above mine workings in the Pennsylvania anthracite region. The first experiment2/ was begun in January 1950, in a section of the mine where about 50 percent of the original coal remained in the form of pillars; since the company did not plan to mine the pillars in this particular area, pneumatic packing of the chamber voids was done for test purposes only. During this initial test the machine was operated on 204 shifts, and 652,400 cubic feet of breaker refuse material (22,834 tons) was packed into the voids of 16 chambers. The work was completed in December 1951.

Jan 1, 1956

By Carl Belser

This report on tungsten in Ouray, San Juan, and San Miguel Counties, Colo., is one of a series describing results of studies on the tungsten potentialities in Region III, Bureau of Mines. The San Juan tungsten deposits occur in an area of 250 square miles, centering near the common corner of Ouray, San Juan, and San Miguel Counties (fig. 1). Field work supporting these studies was done in May 1954. Bureau of Mines reports prepared from investigations made during World War II and under the Defense Production Act of 1950 were reviewed.

Jan 1, 1956

By K. K. Kershner

To meet an increasing demand for high-purity cobalt, the Bureau of Mines has conducted investigations for producing this metal. Cobalt having a purity of 99.95 percent or higher is needed to determine heats of formation, corrosion resistances, phase diagrams, and other basic properties of the element and its compounds. This grade of cobalt may be used for preparing radioactive metal. As a result of its investigations a detailed procedure, which is of practical significance to the production of high-purity cobalt, has been developed by the Bureau for purifying cobalt solutions and for electrolytic deposition of the metal. Cobalt metal, which had a purity of 99.99 percent with reference to metallic contaminations, was deposited electrolytically. Qualitative spectrographic analysis showed only traces of calcium, copper, iron, magnesium, nickel, and zinc.

Jan 1, 1956

By A. J. Barry

A method was developed for testing the anchorages obtained with 3/4-inch, expansion-type, headed bolt and shell assemblies. The apparatus is a modification of that used in testing -inch-diameter, slotted-type bolts. Four makes of expansion-type shells were used in 64 tests made in sandstone and shale roof. The results show that for 3 makes of shells the anchorage effectiveness is independent of the installed land, and for the fourth make of shell a better anchorage is obtained when instilled at a load of 8,000 pounds. The results also show that deformation of the expansion plug influences the majority of the anchorages obtained with two makes of shells. This deformation causes a larger increase in displacement for a given added increment of load. The data from 48 of the 64 tests were combined to establish a relationship between average displacement and increase in bolt load (above the installed load). This relationship can be used to evaluate the anchorage effectiveness of any 3/4-inch-diameter, expansion-type, headed bolt and shell assembly tested in the field.

Jan 1, 1956

By J. D. McLenegan

The purpose of this investigation was to prepare a market survey of the refractories industry in California and Nevada (referred to in subsequent paragraphs as the region), and to determine the degree of self-sufficiency and the potential capacity for anticipated growth. The report includes estimates of the total annual refractories consumption, the quantity of refractories imported into the region, the tonnage of raw materials required for their manufacture, and the resources of fire clay and high-alumina minerals in the region.

Jan 1, 1956

By J. M. Riley

A fluorometric method using morin in an alkaline-buffered chelating solution has been developed by the Bureau of Mines for determining beryllium in ores and mill products. Apparatus for measuring fluorescence intensities of the beryllium-morin reaction is described. Preparation of the sample for analysis consists essentially of digestion with sulfuric, nitric, and hydrofluoric acids, fusion of the residue with sodium carbonate and sodium borate, Solution of the melt with sulfuric acid, and proper dilution. Chemical separation of other ions is usually unnecessary. The method rave reliable beryllium determinations on samples in the 0.01- to 0.37-percent BeO range. The method is particularly applicable to low-grade beryllium ores; however, semiquantitative beryllium determinations have been made on beryl containing 12.0 percent BeO.

Jan 1, 1956

By A. J. Kauffman

The alluvial deposits of the Pacific Northwest have been investigated and worked with varying degrees of intensity since about the middle of the 19th century. Earlier efforts, of course, were centered about the placer-gold content of the deposits; later, the Oregon beach sands were exploited for their chrome content, and, still more recently, deposits in Idaho were worked for their content of monazite, a rare-earth mineral which also contains significant quantities of thorium. The composition of alluvial deposits seems to depend mainly upon the nature of the source rock from which the detrital material was derived and upon the resistance of the individual mineral grains to the agencies of weathering and transportation. The processes of crushing and concentration used in ore dressing are applied in a leisurely but nonetheless effective manner when exposed rock masses are eroded by natural forces. Weathering effects a continuous disintegration and chemical decomposition, wherein resistant minerals are set free as individual grains and new minerals are formed. Erosion carries these detrital products down the slopes into natural waterways, where a mechanical separation of heavy particles from light is accomplished by the running water. The accumulation of such resistant, heavy particles through the ages has resulted in formation of the black-sand deposits. In addition to the associated gangue minerals, heavy sand deposits in the Pacific Northwest may contain the following constituents of possible economic value: Gold, platinum, chromite, ilmenite, magnetite, garnet, zircon, monazite, columbite-tantalite, and radioactive blacks.

Jan 1, 1956

By R. W. Barnes

This circular presents results of a survey conducted by the Bureau of Mines to ascertain the extent to which dust-control practices are employed in the coal-mining industry. This survey was initiated because of increasing realization of the possible harmful effects of the inhalation of dust upon the health of coal-mine workers and the advent, during recent years, of new types of mining machinery and new mining methods that may have a direct effect upon the extent of exposure to airborne dust experienced by persons mining coal. Anthracite Mines The survey covered 169 anthracite mines that were operating from November 1, 1953, to July 1, 1954. It showed that large mines employing more than 100 men were doing most to control dust produced during mining.

Jan 1, 1956

By W. A. Stickney

The Bureau of Mines conducted beneficiation and smelting studies on siliceous offgrade manganese samples to indicate effective methods of manufacturing silicomanganese from materials that cannot be economically beneficiated to meet General Services Administration (GSA) specifications for stockpiling. Laboratory and pilot-plant flotation tests were conducted on 2 samples, 1 from the waste-tailings dump of the Domestic Manganese & Development Co , Butte, Mont., and the other from the Nettie mine in the Butte-Philipsburg area. Smelting tests were made on the combined concentrates from the pilot-plant flotation tests and on part of the tailings sample The flotation scheme found to be adequate in laboratory tests and later in the pilot-plant tests consisted of flotation by a fuel oil-tall oil emulsion in an acid circuit (pH )-1-.8 to 5.0). The oil-emulsion reagent flocculated the manganese minerals and selectively floated them from the siliceous gangue, In the pilot-plant flotation test on Butte-mill tailings 90.1 percent of the manganese was recovered in a concentrate that analyzed 32.6 percent Mn, 4.8 percent Fe and 28.1 percent Si02. In the test on Nettie mine ore 90.8 percent of the manganese was recovered in a concentrate that analyzed 36 6 percent Mn, 5.5 percent Fe, and 26-4 percent Si02.

Jan 1, 1956

By R. J. Hundhausen

The Takilma-Waldo copper district in Josephine County, Oreg., was studied by the Bureau of Mines from September 1950 to April 1.951 and from December 1953 to April 1954. Funds for the investigation were provided by the Bureau of Mines and the California-Oregon Power Co., Medford, Oreg., on a cooperative basis. The copper mines in the district are credited with a total production of ore worth $1,700,000. Since 1933 the mines have been unproductive and, except for minor exploration, largely inactive. The history of the district indicates that the copper deposits were mined principally during periods of high metal prices.

Jan 1, 1956

By J. J. Dowd

1. The Pittsburgh bed is the most important bed in Marshall County, and virtually the entire production of coal in the county comes from this bed. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of coal in place, were estimated at 3,158 million short tons as of January I, 1954. Of this total, 3,071 million short tons is in beds 28 inches and more thick. Areas in each bed except the Pittsburgh were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

A spectrochemical procedure applicable to the determination of iron, manganese, and magnesium in titanium metal and to the determination of alloying constituents in three types of titanium alloys is presented. Acid solutions of samples and standards are excited with a spark-type discharge and porous-cup electrode arrangement. The method is particularly applicable for analyzing samples for which a self-electrode method cannot be used. Calibrations are accomplished with synthetic standard solutions, resulting in a primary method that makes calibrations based upon results of other analytical methods unnecessary. Replicate determinations are reproduced to within 5 percent, and the average percentage deviations from reliable chemical values are less than 6 percent. The method can be extended readily to determine additional elements that are similarly soluble and have similar spectral sensitivities. It also can be used as a starting point to establish standards for a direct sparking procedure for analyzing titanium alloys. In view of the absence of established reliable analytical methods in the titanium industry, the spectrochemical method described here should prove to be a timely contribution.

Jan 1, 1956

By David Schlain

The galvanic corrosion properties of titanium and zirconium were investigated by the Bureau of Mines. The dissimilar metals involved in these experiments included magnesium, magnesium alloy FS1, aluminum alloys, zinc, steel, tin, lead, copper, Monel, nickel, and several stainless steels. Couples were immersed in synthetic ocean water, tap water, 5-percent ammonium sulfate solution, 5-1/2-percent sodium chloride solution, sodium hydroxide solution, 0.1 N hydrochloric acid, and various concentrations of sulfuric acid.

Jan 1, 1956

By F. L. Wideman

This paper is one of a series on mining methods being published by the Bureau of Mines. It describes briefly mining practices at the Sunrise iron mine of the Colorado Fuel & Iron Corp., Platte County, Wyo. The Sunrise mine is in the Hartville iron district in east-central Wyoming (fig. 1). The district covers part of the Hartville Mountains, a region of moderate relief in which erosional features have been formed by the dissection of a low plateau. Altitudes vary from 4,300 feet along the North Platte River to 6,000 feet in the uplift. The climate is semiarid, with hot summers and winter temperatures below zero for short periods. Grasses, cacti, yucca, and low desert shrubs grow at lower elevations. Cottonwood and boxelder trees and willows grow along permanent streams; juniper and coniferous trees are confined to the higher elevations.

Jan 1, 1956

By Russell R. Trengove

Core samples from an ore horizon 2,000 feet below the surface were successfully obtained by rotary drilling at the property of the Eureka Corp., Eureka, Nev. The ore was soft and friable; cores were not obtained previously with diamond drills. Whipstocking was used to get samples in a zone 200 feet from a vertical hole. A technique in shipstocking, by which the direction and deviation of the holes were controlled by means of nonfriction-type survey instruments, was successfully employed.

Jan 1, 1956

By A. B. Needham

This report describes the exploration work done in 1941 in connection with the search for strategic minerals as authorized by the Strategic Materials Act approved by the President on June 7, 1939. It deals with the various manganese deposits and showings in the Tombstone mining district of Cochise County, Ariz. The exploration project comprised a study of the geology, mapping of the areas, and exploration of various mines and deposits by sampling old drifts, crosscuts, and scopes, supplemented by diamond drilling from underground stations. The Federal Government's manganese-purchasing programs have revived interest in occurrences such as the scattered deposits near Tombstone. Because of this, the Bureau of Mines project report on the Tombstone district, prepared originally in 1941 but not published, has been revised and now is being made public.

Jan 1, 1956

By Robert E. Hershey

1. This investigation shows that the most important beds in Claiborne County, from the standpoint of present production and reserves, are the Coal Creek and Jellico. Together, they contain 69 percent of the known recoverable reserves in the county. Reserves in five other beds are tabulated in this report; in order of quantity of reserves, they are: Blue Gem, Lower Pioneer, Pewee, Big Mary, and Rex. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 60 million tons, as of January 1, 1953. Of this total, 55 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to permit making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

By William H. Tavenner

1. The 1952 Annual Report of the West Virginia Department of Mines lists nine beds that arc being mined in Logan County, of which the Cedar Grove and Chilton are the most important. The Cedar Grove group, No. 2 Gas, and Alma beds have the largest remaining reserves, in the order given. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 short tons per acre-foot of coal in place, are estimated at 5,411 million tons as of January 1, 1954. Of this total, 3,939 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics were too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimate reserves.

Jan 1, 1956