Search Documents

By R. Hansson

Zincite and spinel phases are present in the complex slag systems encountered in zinc/lead sintering and zinc smelting processes. These phases form extensive solid solutions and are stable over a wide range of compositions, temperatures and oxygen partial pressures. Accurate information on the stability of these phases is required in order to develop thermodynamic models of these slag systems. Phase equilibria in the Fe-Zn-O system have been experimentally studied for a range of conditions, between 900 and 1580°C and oxygen partial pressures (pO2) between air and metallic iron saturation, using equilibration and quenching techniques. The compositions of the phases were measured using Electron Probe X-ray Microanalysis (EPMA). The ferrous and ferric bulk iron concentrations were determined using a specially developed wet-chemical analysis procedure based on the use of ammonium metavanadate. XRD was used to confirm phase identification. A procedure was developed to overcome the problems associated with evaporation of zinc at lowpO2s and to ensure the achievement of equilibria. An isothermal section of the system FeO-Fe2O3-ZnO at high ZnO concentrations at 1200°C was constructed. The maximum solubilities of iron and zinc in zincite and spinel phases in equilibrium were determined at pO2=1*10-6atm at 1200and 1300°C. The morphology of the zincite crystals sharply changes in air between 1200 and 1300°C from rounded to plate-like. This is shown to be associated with significant increase in total iron concentration, the additional iron being principally in the form of ferric iron. Calculations performed by Fact Sage with a thermodynamically optimized database have been compared with the experimental results. Keywords: Phase Equilibria, Fe-Zn-O, Quenching, Wet-Chemistry, EPMA, XRD, ISP.

Jan 1, 2004

By M. Timucin

Phase relations within the condensed Cu-Cu2S-PbS-Pb region of the Cu-Pb-S ternary were investigated. The boundaries of the ternary liquid-miscibility gap were redrawn, and the directions of the tie-lines were established by the quenching of samples equilibrated in evacuated and sealed silica capsules at 1473 K. The activities of lead in sulphur-saturated Cu-Pb alloys along the boundary of the miscibility gap were measured by the dew-point technique at 1473 K. From the tie-line distributions, measured lead activities, known activities of the Cu2S-PbS join, and the ternary Gibbs-Duhem integration, consistent sets of activities for lead and copper and partial pressures of sulphur were obtained along the ternary miscibility gap at 1473 K.

Jan 1, 1989

By N. Hanief

This research involves the investigation of phase transformations in the platinum-chromium coated system. Single-layer 0.1 µm platinum coatings were deposited via electron beam deposition on 99.98 percent pure chromium substrates. Specimens were subjected to systematic heat treatment in a vacuum furnace at 900°C for up to 20 hours. Phase formation and the changes in surface morphology were investigated by X-ray diffraction (XRD) and scanning electron microscopy (SEM).Both CrPt and Cr3Pt phases are formed during heat treatment for different times at 900°C. Significant changes in the morphology of this coated system were detected after heat treatment at 900°C for 20 hours.

Jan 1, 2012

By N. Hanief

This research involves the investigation of phase transformations in the platinum-chromium coated system. Single-layer 0.1 µm platinum coatings were deposited via electron beam deposition on 99.98 percent pure chromium substrates. Specimens were subjected to systematic heat treatment in a vacuum furnace at 900°C for up to 20 hours. Phase formation and the changes in surface morphology were investigated by X-ray diffraction (XRD) and scanning electron microscopy (SEM).Both CrPt and Cr3Pt phases are formed during heat treatment for different times at 900°C. Significant changes in the morphology of this coated system were detected after heat treatment at 900°C for 20 hours.

Jan 1, 2012

By M. Natarajan, C. J. Cutler, E. Mponda

Keywords: Pyrometallurgy, furnace, KCM Nkana, Zambia The Nkana smelter was initially commissioned in 1931, with two reverberatory furnaces, two Peirce-Smith converters, and blister copper casting facilities. Reverberatory furnaces were the mainstay of production up until 1994, when an El Teniente Converter (CT) was installed to upgrade reverberatory furnace matte to white metal, prior to converting in conventional Peirce-Smith (PS) converters. In 2000, a decision was taken to increase the proportion of concentrate smelted in the CT by introduction of bone-dry concentrate injection through the tuyeres. A flash dryer with a nominal capacity of 1 200 metric tons per day of dry product, and associated tuyere injection system was commissioned in March 2004. Based on the projected concentrate arisings from the KCM mines into the future, as seen in 2004, it was decided to develop the CT to be the primary smelting vessel at Nkana, to handle a minimum of 1 250 tons per day of concentrate, and to operate only one reverberatory furnace in slag-cleaning mode pending a full evaluation of alternative slag-cleaning technologies. The anticipated cathode production from Nkana was to be in the range 140 to 150 000 tons per annum. This paper details the outcomes from trials that were carried out in August and September 2004, using two reverberatory furnaces for slag cleaning. The results of these trials, plus further work in October and November, provided confidence to move to one reverberatory furnace for slag cleaning in December 2004. With the advent of Vedanta as the majority shareholder in KCM at the end of 2004, the approach has been to maximize the available smelting capacity. Currently, two reverberatory furnaces and the CT are on-line, with the higher silica concentrates going to the reverberatory furnaces with an appropriate amount of pyrite, and the cleaner concentrates going to the CT. Expansion of the smelter is currently under investigation.

Jan 1, 2006

It is shown that, when a flat-bottomed indentor is pressed into the surface of a strong rock, the normal force necessary to cause failure of the rock is reduced substantially if a shear force is applied to the indentor. A mathematical analysis is described, which shows that higher stresses are induced in an elastic material close to the free surface of the material ahead of a punch when a shear force together with a normal force is applied to the punch. Therefore, failure of the material would occur with lower forces applied to the punch. Stress trajectories show that fractures develop in the rock along lines of maximum principal stresses.

Jan 1, 1978

By A. Nicotra, E. H. Roux, J. H. du Plooy, D. H. de Jagger, P. De Waal, G. J. van der Linde

This paper reviews the geology, history, current beneficiation practices, uses, marketing, and future outlook of phosphate in South Africa. The vastness of the reserves, and the industry's efficiency and competitiveness in world terms, are highlighted.

Jan 1, 1989

By Y. J. F. Haven, G. H. J. Kitson, D. G. Beadle

I have read this paper with considerable interest. By using an automatic instrument to assess the dust samples taken in South African collieries, the authors are ahead of the gold mining industry, which still uses the laborious method of microscopic assessment, with its limited accuracy, of the half-a-million dust samples taken each year. As the authors state, the result obtained from the photoelectric assessment of the samples is approximately proportional to the surface area of the respirable dust. However, modern theory is that, in assessing coal dust, it is the respirable mass which is important in determining the danger to health. Thus Table II of their paper is of considerable value in showing the relationship between the P.E.R. value and the mass concentration measurement. Unfortunately this table only gives the mean relationship. The important point is to know the scatter around this mean. If the scatter is small, then this mean value (for different operations) would have considerable value in converting from respirable surface area to respirable mass, but if the scatter is large, then such a conversion, using a fixed factor, will have little value. In the text the authors mention the range of values as being between 3 to 24, but without a statement on the number of samples used to determine this range and their distribution, this is a rather nebulous statement. I hope, in their reply, that the authors will give, in statistical terms, some statement on the overall correlation between these two parameters. I might add that at present a member of my staff is working on similar relationships for dust samples taken in gold mines. Another factor which may well be most important in determining the danger of dust levels in coal mines is the composition of the dust, specifically its quartz content. I understand that the authors have some information on this point, and to make their results of greater value in International comparisons of dust levels and the concomitant development of pneumoconiosis, it will be extremely useful if they could place this information on record. Even though, as I have said above, modern theory postulates that respirable mass is a better parameter to use than respirable surface area, the problem remains of how to measure this parameter with short time sampling, which, as the authors point out, is their preferred strategy for dust sampling and dust control. I know of no easily portable instrument, independent of external power supplies, which can, in 5 to 10 minutes, collect sufficient dust to enable it to be weighed accurately. Thus the authors' implied intention of continuing to sample by their present techniques and using their present parameter to report the results is, in my opinion, an entirely valid decision.

Jan 10, 1968

By G. Poropat, A. R. Guest, H. P. Grobler

At the De Beers Consolidates Mines operations it is common practices to perform Geotechnical mapping of the newly exposed faces in the waste and ore rock. The purpose of Geotechnical mapping is to quantify the in-situ fracturing of a rockmass that in turn is required during the planning and application of a mining method. Whether it is to determine slope angles, caveability, impact of blasting or support requirements. This mapping involved a cumbersome and time consuming procedure that requires individual examination and description of the natural inherent fractures exposed by mining. During highwall mapping in an open pit this can be a safety concern due to the duration of time spent below a highwall. The advantages gained through the recent introduction and application of SiroVision® allows safer mapping, an increase in statistical fracture population, archiving of rock faces and the more accurate reflection of the true mapping. This paper aims to describe in detail the application of the recently developed SiroVision®, photogrammetry software, to replace conventional face mapping. A De Beers Consolidated Mines, il est pratique courante de faire une cartographie géotechnique des tailles récemment exposées dans le rocher stérile ou minerai. Le but de la cartographie géotechnique est de quantifier la fracturation in-situ d’une masse rocheuse, qui sera nécessaire lors de la planification et application d’une méthode minière, que ce soit pour déterminer les angles des galeries inclinées, les possibilités de foudroyage, l’impact du dynamitage, ou les besoins en supports. Cette cartographie nécessitait une procédure longue et compliquée qui demande l’examen individuel et la description des fractures naturelles propres exposées par l’opération de mine. Pendant la cartographie de parois dans une exploitation à ciel ouvert, cette opération peut être dangereuse à cause du temps passé sous la paroi. Récemment, le lancement et application de Siro Vision apportent l’avantage d’une cartographie plus sûre, une augmentation des statistiques de population de fracture, l’archivage des tailles de roches, et le reflet plus précis de la cartographie. Le but de l’étude présente est de décrire en détail l’application du développement récent de Siro Vision, logiciel de photogrammétrie, pour remplacer la cartographie de taille conventionnelle. Bei den De Beers Consolidates Mines Operationen ist es gängige Praxis geotechnische Aufzeichungen des Taub- und Erzgesteins neu geöffneter Abbaustellen zu erstellen. Zweck dieser geotechnischen Aufzeichnungen ist die vor-Ort-Quantifizierung des Bruches der Gesteinsmasse, welche im Gegenzug während der Planung und der Anwendung einer Abbaumethode erforderlich ist, sei es um einen Neigungswinkel festzustellen, Abbaubarkeit, Auswirkung von Sprengungen oder Anforderungen an Unterstützungen. Die Aufzeichnungen waren mit umständlichen und zeitaufwendigen Prozeduren verbunden, die eine individuelle Prüfung und Beschreibung der durch den Abbau freigelegten natürlichen inhärenten Brüche, verlangten. Dies kann auf Grund des Zeitraumes der unterhalb einer Flözoberschicht verbringt wird zu einer Frage der Sicherheit werden wenn die Aufzeichnung einer Flözoberschicht im Tagbau erfolgt. Die Vorteile auf Grund der jüngst erfolgten Einführung und Anwendung der SiroVision® gestatten sichereres Aufzeichen, eine Zunahme in der statistischen Menge an Gesteinsbrüchen und eine akkuratere Reflektion der tatsächlichen Aufzeichnungen. Diese Arbeit hat zum Ziel im Detail die Anwendung der kürzlich entwickelten SiroVision®, eine photogrammetrische Software, die die konventionelle Abbauortaufzeichnung ersetzen soll zu beschreiben.

Jan 1, 2003

By A. Singh, R. R. Maclachlan

SYNOPSIS A back-analysis procedure based upon 35 mm photography was developed on a laboratory scale for the pur¬pose of determining the percentage of oversize particles known to be present in heaps of fragmented rock. Eight simple blends of crushed stone containing varying percentages of oversize on a 1:40 modelled scale were examined. Simulated test conditions for the following were subjected to the photographic study: (1) a bench heap, (2) the surface exposure of a partially excavated heap, (3) a gravity-sorted surface as occurs on an apron dump, and (4) four quadrant views of an incrementally built conical heap of rock fragments. The best back-analysis determinations were obtained from (4), the cone, over all eight blends of fragments. The mean error was within -0,16 per cent of the true value, with a range of ± 1,872. This was for oversize contents of 5 to 20 per cent where a minimum 25 per cent of the photograph area was processed by digitizer. The worst results were from the apron dump at - 1,462 per cent for a mean error of ± 4,174 per cent. The intermediate results were from the undisturbed bench at -0,186 per cent with a mean error of ±2,862 per cent.

Jan 1, 1989

By R. J. Gordon, N. J. Keys, N. F. Peverett

Photometric sorting of ore on a South African gold mine by N. J. KEYS. B.E. Met. (Queensland) (Visitor). R. J. GORDON. (Visitor). And N. F. PEVERETT. B.Sc. (Eng.) (Wits) (Fellow) This paper concerns the development and application of a high-throughput, multi-stream photometric sorting machine developed for the South African gold mines. It is now believed that this sorter and its progeny may be found suitable for a large proportion of all possible sorting applications. A laser-light source and sensitive photomultiplier are employed in a scanning system to detect light reflected from the surfaces of rocks passing through the sorting zone. Electronic circuitry then analyses the photomultiplier signal, which represents the varying intensity of the reflected light, and produces control signals to actuate the appropriate valves of an array of air-blast rejection devices to remove from the feed certain particles selected by the analysing process. Typical throughput per machine ranges from 50 t/h for a minus 60mm plus 30mm feed to 200 t/h for minus 150mm plus 70mm material.

Jan 9, 1974

By J. H. Cloete, S. M. Bradshaw, D. K. Chibwe

"The primary function of a tundish in the steelmaking industry is to serve as a buffer tank, accepting molten steel from the batch ladle process and allowing it to be cast continuously. However, modern steelmaking has more stringent demands for the quality of the steel product, requiring increased control over the properties of the molten steel before casting. For this reason tundishes have been developed as metallurgical reactors to serve as the final step in refining of the molten steel by removing non-metallic inclusions, preventing the formation of new inclusions, and promoting chemical and thermal homogeneity. In this study the flow behaviour in a four-strand tundish was investigated by means of a half-scale water model as well as numerical modelling. Both the numerical study and physical model were used to characterize residence time distribution (RTD) in the vessel and calculate properties pertaining to the tundish flow regime. Three different tundish configurations were investigated: a bare tundish with no flow control devices, a tundish with a turbulence inhibitor and a tundish with both a turbulence inhibitor and a dam.The physical and numerical models showed that a tundish without flow control devices was prone to significant short-circuiting. A tundish with a turbulence inhibitor was shown to be successful in preventing short-circuiting and provided surface-directed flow, which aids inclusion removal in the slag. Despite the benefits of the use of turbulence inhibitors, it was observed that the upward-directed flow increased the maximum turbulence kinetic energy near to the surface by approximately 120% compared with the bare tundish. Therefore the potential for slag entrainment should be considered during the design and operation of tundishes utilizing turbulence inhibitors."

Jan 1, 2014

By J. H. Cloete, S. M. Bradshaw, D. K. Chibwe

"Modern tundishes have evolved as vessels to serve as the final step in refining of molten steel by removing inclusions and promoting thermochemical homogeneity.In this study the flow behaviour in a four-strand tundish was investigated by means of a ½-scale water model as well as numerical modelling. The numerical and physical models were used to characterize residence time distribution and calculate properties pertaining to tundish flow regime. Three different tundish configurations were investigated: a bare tundish with no flow control devices, a tundish with a turbulence inhibitor, and a tundish with both a turbulence inhibitor and a dam.The physical and numerical models showed that a tundish without flow control devices is prone to significant short-circuiting. A tundish with a turbulence inhibitor was shown to be successful in preventing shortcircuiting and provided surface-directed flow that might assist the removal of inclusions from the melt. However, it was also observed that the upward-directed flow caused the maximum turbulence kinetic energy near the surface to increase dramatically. The potential for slag entrainment should therefore be considered during the design and operation of tundishes with turbulence inhibitors."

Jan 1, 2015

By M. U. Ozbay

This paper presents an overview of the research that has been carried out to improve the understanding of the fracture processes occurring in rock under high levels of stress. The onset and growth of fractures are studied by means of laboratory model testing, and the results obtained are used in the calibration and validation of the numerical model DIGS, which is based on displacement discontinuity. The results obtained so far have shown that, while there are overall similarities between the experimental results and the numerical simulations, improvements to the experimental procedures and the DIGS are required for a detailed mechanistic understanding of shear-band orientations and extension fractures.

Jan 1, 1996

By L. A. Vermeulen

Electronic circuits were developed and successfully utilized to record, store, and continuously transmit to a remote station physical information relating to the impacts of pebbles on the shell liners of an industrial pebble mill, and of electrical conduction in the mineral pulp. The information was obtained by the instrumentation of some of the bolts that are used to clamp the liner blocks and litter bars to the mill shell. The features associated with the impact and conduction signals have been interpreted, and it is shown that such signals can lead to continuous measurements of the volume of the load in an industrial mill. Information is given regarding the angular distribution of direct impacts of the pebbles onto the shell liners, the power required to promote impacts, the amount of material in flight, the impact velocity, and the average number of direct impacts with the shell liner that any given pebble undergoes in unit time in the given mill.

Jan 1, 1984

A physical modelling study has been carried out to simulate the slag-metal dispersion induced by a high-strength bottom gas injection. Water and kerosene were utilized to simulate metal and slag respectively. A water model of CLU (Creusot-Loire Uddeholm) vessel was used with three different nozzle orientations, namely, off-centre, triangular off-centre and centre. The gas flow rates changed from 0.00599m3/sec to 0.01081m3/sec. Height of heavy and light phases was kept fixed at 0.23 m and 0.02 m respectively. The dispersed phase holdup was determined at various axial and radial distances, gas flow rates, and tuyere configurations. The observations revealed that at a fixed gas injection rate, as the vertical distance increased in the centerline, straight off-centre orientation resulted in greater dispersed phase hold up values than those of the centre configuration and the triangular off-centre orientation. The dispersed phase holdup was found to increase with gas injection rate and decreased with axial distance. The variation of the dispersed phase hold up with the dimensionless axial distance and the gas injection rate was correlated by using the Modified Froude Number. The experimental values of the dispersed phase holdup were found to be in good agreement with the correlated values obtained from the modelling equations. The findings of the present study may be utilized in the ferroalloy refining vessels in terms of designing tuyere locations for optimum processing conditions.

Jan 1, 2004

A physical modelling study has been carried out to simulate the slag-metal dispersion induced by a high-strength bottom gas injection. Water and kerosene were utilized to simulate metal and slag respectively. A water model of CLU (Creusot-Loire Uddeholm)vessel was used with three different nozzle orientations, namely, off-centre, triangular off-centre and centre. The gas flow rates changed from 0.00599 m3/s to 0.01081 m3/s. Height of heavy and light phases was kept fixed at 0.23 m and 0.02 m respectively. The dispersed phase hold-up was determined at various axial and radial distances, gas flow rates, and tuyere configurations. The observations revealed that at a fixed gas injection rate, as the vertical distance increased in the centerline, straight off-centre orientation resulted in greater dispersed phase hold-up values than those of the centre configuration and the triangular off-centre orientation. The dispersed phase hold-up was found to increase with gas injection rate and decreased with axial distance. The variation of the dispersed phase hold-up with the dimensionless axial distance and the gas injection rate was correlated by using the modified Froude number. The experimental values of the dispersed phase hold-up were found to be in reasonable agreement with the correlated values obtained from the modelling equations. The findings of the present study may be utilized in the ferroalloy refining vessels in terms of designing tuyere locations for optimum processing conditions.

Jan 1, 2004

By H. Hamma, R. Fehrmann, M. Gaune-Escard, G. Hatem, S. B. Rasmussen, K. M. Eriksen

The molten salts M2S2O7and MHSO4, the binary molten salt systems M2S2O7-MHSO4and the molten salt-gas systems M2S2O7-V2O5and M2S2O7-M2SO4-V2O5(M = Na, K, Rb, Cs) in O2, SO2and Ar atmospheres have been investigated by thermal methods like calorimetry, Differential Enthalpic Analysis (DEA) and Differential Scanning Calorimetry (DSC). Fundamental thermodynamic data like temperatures and molar heats of solid-solid transition and fusion, phase diagrams, heat capacities of solids and liquids, heat of mixing, and heats of complex formation have been obtained and are reviewed here. Also EPR spectroscopic evidence of V(IV) complexes and their structure are reported and the results are discussed in relation to the mechanism of SO2oxidation by V2O5based industrial catalysts. Keywords: Alkali pyrosulfates, alkali hydrogen sulfates, vanadium pentoxide, EPR spectroscopy, complex formation

Jan 1, 2004

By E. Pothas, P. R. Jochens, L. B. McRae, D. D. Howat

SYNOPSIS The phase equilibria, viscosities and sulphur capacities of titaniferous slags were determined in the composition range of CaO = 30 to 0 per cent, MgO = 0 to 30 per cent, SiO2 = 19.69 per cent, AI.O. = 13.12 per cent and TiO2 = 37.19 per cent. The phase equilibria were determined by high temperature microscopy, the viscosities were measured using a rotating outer cylinder viscometer and the sulphur capacities were evaluated from the results obtained by equilibrating the slag in a gas stream of CO, CO2 and SO2. The behaviour of these titaniferous slags under reducing conditions was examined. Possible use of the slags for aggregate, or slag-cement, and the possibility of extracting the TiO2 are discussed. CONTENTS INTRODUCTION PHASE EQUILIBRIA VISCOSITIES DISCUSSION OF THE PHASE EQUILlBRIA AND THE VISCOSITY VALUES EFFECT OF REDUCING CONDITIONS SULPHUR CAPACITY DISCUSSION OF THE SULPHUR CAPACITY VALUES POSSIBLE USES CONCLUSIONS ACKNOWLEDGEMENTS REFERENCES INTRODUCTION The latest phase in the exploitation of the mineral wealth of the Bushveld Igneous Complex is the erection of a plant by the Highveld Steel and Vanadium Corporation Limited near Witbank to produce steel and vanadium-rich slag from the titaniferous magnetites occurring in this rock formation. These titaniferous magnetites occur as segregations in the gabbro body and the TiO2 is mainly present within the structure of other constituent minerals but also occurs in smaller amounts as ilmenite and ulvospinel. The vanadium is thought to be present in the iron oxide phase due to isomorphous replacement of the iron. Until very recently, it was feared that the high titania content of these titaniferous magnetites would militate against their value as useful iron ores. However, the design of an integrated plant to produce both steel and vanadium-rich slag, and in which the iron-making process is conducted in submerged arc furnaces instead of in

By E. Pothas, P. R. Jochens, L. B. McRae, D. D. Howat

Discussion H. J. S. Kriek*: During 1956 Iscor became interested in the acid smelting in a blast furnace of siliceous ores containing 15 per cent silica. This interest was as a result of the successful acid smelting in Germany at a CaO/SiO2-ratio of between 0.4 and 0.8. Acid smelting can become an economic proposition due to a reduction in slag volume accompanied by a lowering of the coke rate. Paschke and Hannel1 found that a free flowing slag (i.e. viscosities of less than two poise) would not be obtained at C/S-ratios lower than 0.82 and that the addition of 3 to 4 per cent alkalies became necessary. In titanium bearing slags it was established that maximum fluidity is obtained with 10 per cent TiO2. Acid smelting resulted in increased sulphur pickup with decreasing O/S-ratio and desulphurization with soda-ash outside the blast furnace was necessary. At Iscor Mr B. B. Segal established that, for slags with (CaO+MgO)/SiO2-ratios of 0.5, 0.6 and 0.7, the addition of alkalies and TiO2 resulted in a substantial decrease in melting point and also of viscosity. At a (CaO+ MgO)/ ratio of 0.53 the addition of 10 per cent TiO2 is as effective as the addition of 3.75 per cent alkalies. This means that a blast furnace can be run without the addition of alkalies and consequently the detrimental effect of alkalies on the lining can be avoided; also that fluid slags with 5 to 15 per cent MgO and 8 to 10 per cent Al203 can be obtained with 10 per cent TiO present. (CaO+ MgO)/SiO2-ratios smaller than 0.5 the addition of titania resulted in a decrease in melting point and also in an increase in viscosity. In ceramic crucibles the slag did not become more viscous with time but thickened appreciably when held in graphite crucibles. No titanium carbonitride could be detected and only Ti20a was found. Prof Howat also did not obtain the TiC-TiN solid solution and therefore it appears that the thickening of the slag is not solely due to the formation of the titanium carbonitrides. This is in agreement with the work of Michailov and Belyakova2 who found that TiO2 decreased the viscosity of acid slags and increased the viscosity of basic slags; that titanium sesquioxide (Ti203) and titanium monoxide (TiO) increased the viscosity of both acid and basic slags and that titanium carbide, which is found in larger amounts in basic slags than in acid slags, considerably increases the viscosity of both acid and basic slags. Patzak et al3 describes the following oxygen deficient titanias, viz Ti2O, TiO, Ti203, Ti3O5, Ti4O7, Ti5O9, Ti6O11- Ti10O9,Ti7O13,Ti8O15 and Ti9O17. Until about 1959 a fair amount of data was available on the viscosity of normal slags to which titania was added2, 4, 5, 6, 7, 8, 9. At Iscor an electromagnetic viscometer based on the viscometer developed by Bockris10 was built. Progress was very slow as our main attention was centred around problems associated with the operation of the Rotor process. During 1962 and 1963 two papers containing fundamental work on the viscosities of slags in the systems CaO-SiO2-TiO211 and CaO-SiO2-TiO2 at 0 per cent A1203, 10 per cent Al203 and 20 per cent Al20312 appeared. The work of Ross and Ohno obviated the necessity of any further work by Iscor on the viscosity of blast furnace slags containing titania. Ross gave the following optimum compositions for blast furnace slags containing titania. Titania % Lime % Silica % Lime/Silica-ratio 20 30-42 38-50 0.6-1.10 30 27-36 34-43 0.63-1.06 40 24-32 28-36 0.66-1.14 The optimum temperature is 1,500°C because at this temperature the largest workable composition range exists. Higher temperatures result in narrower optimum composition ranges and in increased rates of thickening. The factors affecting the rate of thickening were also investigated by Ross and Ohno, as the main problem with slags containing titania is not finding compositions which are fluid at operating temperatures but the thickening due to a lack of oxygen. With these slags when there is insufficient oxygen to co-ordinate each silicon atom with its own individual shell of four oxygen ions, some sharing of oxygen ions must occur, resulting in the formation of large silicate ions and a rise in viscosity. The formation of oxygen deficient titania can be prevented as long as iron oxide or manganese oxide remain in the liquid slag. Iwase13 and also Viens, Camp bell and Rogers14 obtained in the experimental smelting of ilmenite ores fluid slags with more than 3 to 5 per cent manganese oxide and ferrous oxide in the slags. It appears that titaniferous ores can be smelted in blast furnaces under the following conditions: (1) Acid slag operation, i.e. at C/S-ratios from O.6-1.0. (2) Dolomite can be used as a flux as MgO is a network modifier. (3) The Al2O3-content must be less than 15 per cent as alumina promotes thickening of the slag and decreases the optimum composition range. (4) The hearth temperature must not exceed 1,500°C. According to Ross a definite amount of energy is required for each ton of iron produced and in order to increase production an increase in heat

Jan 6, 1969