Search Documents

By E. J. Magri, D. M. Hawkins

This paper deals with an experimental programme carried out with a gold analyser in the period June to September 1979 at Loraine Gold Mines. The results were found to be reproducible, with no overall or conditional bias when the measurements were compared with those obtained from chip samples. The standard error of estimation of a 3 m reef exposure, which was the sampling interval, can be reduced by a factor of 2,5 if the complete stretch is scanned, rather than the taking of one chip sample in its centre. Complete statistical and computational procedures were developed for the fitting of the normal-Iognormal model to observed analyser data and for the determination of the most likely gold grade for a particular analyser measurement. (This corection procedure is necessary since a significant number of negative analyser measurements can be observed.) Panel averages of uncorrected scans showed a small conditional bias relative to those of corrected scans. However, uncorrected panel averages can be used for on-the-spot decisions regarding whole panels. For standard calculations of ore reserves, use should be made of corrected scans. Under reasonable assumptions, the use of the detector in the selective mining of low-grade narrow reefs such as the Basal Reef at Loraine Gold Mines, when compared with the conventional chip-sampling method, can result in a saving of as high as R40 million in present-money terms over the life of a project. The difference could be even larger in a highly variable reef like the B Reef at Loraine Gold Mines.

Jan 1, 1987

By A. Galibois, A. Dubé, H. Monette, J. L. Collins

"The start of mining operations often raises serious financial problems. In marginal cases promoters frequently demand financial aid from governments.In the past, the financial assistance has taken the form of gifts, procurement contracts, etc., but aid in such form has been severely criticized. A new formula has been developed to provide a more equitable distribution of the revenues accruing to the government and to private capital.The benefits to these two parties have been evaluated in an hypothetical case and compared in terms of internal rates of return on their investment, their shares of the undiscounted cash flows and their primary profits.The method based on the non-zero sum game theory provides a means for suggesting the lowest feasible annual production and the optimal sum contributed by the government in the form of outright gift, equity capital and convertible bonds. Other financial hypotheses can also be optimized by the computerized analysis."

Jan 1, 2014

By H. Hearnden

Whereas in the past, ladles were simply a means of transferring molten products from furnace tapholes to points of discharge be they casting pans or waste dumps, the ladle is now becoming a more integral and versatile piece of equipment in the pyrometallurgical plant. The drive behind this development is the need for continuous improvement in performance where better, faster and cheaper means remaining competitive in the global market. This paper will explore the technologies available for the rendering of a costly and otherwise cumbersome piece of pyrometallurgical equipment more efficient and versatile in adding value to the final product. Essentially it all revolves around heat and more importantly the loss of it when tapping. The common practice is to move the molten product to its point of discharge quickly with the minimum of interruption to prevent skulling and hence the cost associated with clearing it. The advances in Oxy-fuel burners, AC or DC ladle furnaces, converters, gas purging and high velocity, bath injection systems has increased the versatility of processes and enhanced the potential for adding value to intermediate products through down stream practices such as granulation and atomisation.

Jan 1, 2004

By D. Limpitlaw

The origins of mine closure practice have influenced the way in which it is implemented by companies and regulators. Mine closure practices essentially started developing in the 1970s in countries with advanced economies and mature mining industries. In these settings, the emphasis was justifiably placed on restoration of the landscape and an attempt was made to return to the ?natural? pre-mining land cover. These practices continued to evolve and incorporated socio-economic and cultural aspects, especially after the Brundtland Report in 1987 and the subsequent Earth Summit in 1992. Today mining is increasingly occurring in remote parts of developing countries where there may be significant need for infrastructure such as roads, clinics, and schools. The costs of returning land to low (economic) value pre-mining use may be far greater than establishing a viable postmining land use that could potentially add value to the community and take pressure off sites for greenfield development elsewhere. Furthermore, natural resource limitations (such as topsoil availability) may limit the degree to which the historical land cover can be re-established. Establishing post-mining land uses may aid in mitigating the loss of employment that is inevitable when mines close. Stakeholder participation in establishing post-mining land cover and land use options is critical for long-term success. Similarly, third parties must be identified to support the development of the post-mining land use This paper draws on the experience of the authors in several developing countries and presents a case for maximizing re-use of mining infrastructure. The paper does not advocate the adoption of poor rehabilitation standards, nor or the wholesale destruction of land capability, but rather leaving key infrastructure in place for post-mining use that may support sustainable development.

Jan 1, 2014

By D. van Heerden, M. F. Breed

"Successful development of projects or life-of-mine strategies requires an understanding of the relative sensitivity of value drivers such as grade, tonnage, energy costs, direct operational costs, and recoveries. For example, the results could vary significantly depending on the grade strategy, given a specific orebody amenable to open pitting.Pit optimization is a very powerful tool widely used in the industry to determine the pit shell with the most attractive value potential. Based on the input parameters utilized, the pit optimization process determines the stripping ratio, mineable reserves, and pit shape, and effectively calculates a cut-off grade, assumed to be the optimal cut-off grade.Once the initial pit optimization process is completed, the need may arise to align the optimization results with the company strategy by further optimizing other criteria, such as maximizing short-term cash flow. This paper describes and discusses the selection of an alternative cutoff grade as a strategic intervention. It involves changing the cut-off grade, effectively increasing the head grade to gain a strategic advantage aligned with the company strategy, with a clear understanding of the financial value impact. With this knowledge, it is clear that pitoptimization establishes the basis for future analysis and refinement.IntroductionIt is common for companies to select the optimal pit shell defining the mineral reserve without much further consideration. However, companies may consider various strategies to optimize the long-term value of the project or to optimize the short-term cash flow. Analysis of the entire life-of-mine value estimation process shows that the selection of a cut-off grade and other parameters should be based on careful analysis. Determining the optimal cut-off grade of ore at a different period during the life of mine to maximize the value is often one of the most difficult challenges for a company.A cut-off grade is the lowest grade that mining activities will target. As a result the average mining grade, which drives the value of a project, will always be higher than the cutoff grade applied.According to Bascetin and Nieto (2007) cut-off optimization is still not widely practised. Cut-off grade optimization is an effort to maximize the value of a project by understanding the capacity constraints in the mine, mill, and the market. At any point during the life of mine, any or all of the limitations on tonnage mined, tonnage milled, and product sold may be constraining the system. To ensure cut-off optimization is done correctly, the capacity constraints must be independent of the cut-off grade."

Jan 1, 2016

By B. Friedrich, A. Birich

Gold has been a metal of special importance for mankind for several thousand years. Its outstanding chemical resistance is an important property of this noble metal, but becomes a disadvantage when it comes to gold recovery. The established processes are based on highly aggressive and toxic reagents. Different alternative leaching reagents with a significantly lower toxicity proved to be promising alternatives in the last decades. Major research activities in this field focused on gold ores, so that leaching of secondary resources were not described sufficiently. Based on literature research and extensive experimental investigations, a reagent assessment was conducted for hydrometallurgical gold recovery from electronic waste. It was found that besides thiourea and halides, thiosulfate in particular represents an alternative of major relevance. A variety of different electronic waste (e-waste) specimens were investigated to identify suitable leaching conditions. As a result, an almost complete and selective gold recovery in less than 48 hours from different electronic waste types and components was achieved by thiosulfate leaching. Within the experiments conducted, it was found that the leaching behaviour of cyanide alternative lixiviants differ strongly from leaching of primary ores. Keywords: Gold leaching, cyanide alternative, thiosulfate, electronic waste

Jan 1, 2020

By L. A. Thompson, A. J. Linington

"Copper–cobalt extraction is a reagent-intensive process resulting in acid consumption greatly contributing towards production costs, which in the current market conditions curtail profitability. Nanofiltration (NF) membranes have become an attractive approach in the mining and minerals industry for product concentration and reagent recovery based on the ability of the membrane to separate monovalent ions from divalent ions. NF membranes can selectively separate acids from metals and salts allowing acid to be recycled as well as the concentration and purification of product streams. Membrane technology in the field of copper–cobalt processing focusses on the concentration of Cu2+ and Co2+ in the pregnant leach solution, recovery of acid from waste streams to neutralization, recovery of valuable metals from waste ponds and process water recovery. This paper aims to provide insight into the potential applications of NF membranes in copper–cobalt processing circuits as well as a brief overview of the effects of process conditions on membrane performance and process development. INTRODUCTION The copper–cobalt industry commonly uses inorganic acids, such as sulfuric acid, in large quantities for primary leaching of copper–cobalt oxide ores and releaching during product purification (Stuurman et al., 2014). This results in numerous acidic intermediate streams containing high metal concentrations and acidic waste streams with low metal concentrations. Acid consumption typically accounts for 10–15% of the operating costs of mines in the Democratic Republic of Congo (DRC) and Zambia (Acid Plant Database, 2015). Due to remote mine locations, poorly maintained roads and cross-border conflict, the cost of sulphuric acid can range between USD 300 and 400 per ton. The pivotal role of acid in the copper–cobalt extraction process has driven many mines to build sulphuric acid plants on site to ensure a reliable acid supply, however elemental sulphur still needs to be imported which faces similar logistical challenges and contributes towards operating costs."

Jan 1, 2015

By T. Groenewald

Potential applications of thiourea In the processing of gold by T. GROENEWALD, Ph.D. (Rand), D.I.C. (Imperial College) (Visitor) The aqueous chemistry of gold(l) that has found practical application is mainly the chemistry of the anionic complexes involving ligands such as cyanide. sulphite, and the halides. The one potential exception is the cationic gold(I)-thiourea ion. While many laboratory studies have been made during the past decade. the application of thiourea in the processing of gold is only now reaching the development stage. While thiourea is relatively inexpensive. recent interest has probably been spurred mainly by the novel technology that could arise out of the cationic properties of the gold-thiourea ion. This review outlines the chemistry of gold and thiourea. and discusses the possible use of thiourea in the processing of gold with respect to dissolution. solvent extraction. ion exchange, electrowinning. electroplating. electroless deposition. electro-etching, and electropolishing.

Jan 6, 1977

By J. Engelbrecht

Understanding the deportment of minerals in size fractions has already led to improvements in the flow sheets for platinum minerals beneficiation. There are, however, more potential changes in the flow sheets that may improve the recovery of platinum group metals or reduce the costs of beneficiation before refining. Based on known technology of pre-concentration, milling, gravity concentration, flotation, and magnetic separation a number of potential alterations or additions can be considered and motivated based on the mineral deportment in size fractions.

Jan 1, 2012

By J. Manchisi

Laboratory investigations were conducted to establish the feasibility of bioleaching a mixed copper oxide/sulphide rougher concentrate from Nchanga Mine on the Zambian Copperbelt. The objective was to determine the kinetics and extent of copper extraction for this material. Batch experiments were conducted under different solution conditions in stirred tank bioreactors. The progress of (bio)leaching was monitored through measurements of soluble ferrous and ferric iron, copper, pH, and redox potentials, while bacterial activity was monitored online through 02 and C02 gas utilization rates. About 20 per cent copper was solubilized within 2 hours in all cases of non-oxidative (abiotic), oxidative (abiotic), and bioleaching experiments. This was attributed to the dissolution of mainly copper oxides. Subsequently, bioleaching experiments resulted in an overall copper extraction of 93 per cent, with up to 8 g.L-1 copper after six leaching days, compared to 58 per cent copper extraction in the abiotic oxidative acid leaching experiments. However, there was little effect of time (i.e. poor dissolution kinetics) on copper recovery for abiotic non-oxidative acid leaching of the material. Hence, the rate of sulphide leaching increased due to the activity of bacteria. Thus, the material is potentially bioleachable under mesophilic conditions. However, more exhaustive test work needs to be conducted to establish the effect of bioleaching variables and heat requirement.

Jan 1, 2012

By N. C. Joughin

Potential for the mechanization of stoping in gold mines by N. C. JOUGHIN B.Sc. Eng., Ph.D. (Rand) (Member) The basic requirements for stoping machines are identified first by examination of the mining rates and productivities attained in conventional stoping, and then by examination of a series of problem areas associated with the shape of the reefs, rockbreaking, rockhandling, and the support and design of the machines. Some of the more important machines being developed are described briefly, and their principal features are compared with the basic requirements identified in the first part of the paper. An estimate of the potential demand for the different types of machines is given.

Jan 1, 1976

By N. Steven

Published parameters from the Mufulira copper in situ leach (ISL) in Zambia are used for order-of-magnitude flow-rate calculations for an envisaged gold ISL in back-filled Witwatersrand stopes. A successful leach operation requires that the porous medium, usually a sand, has a hydraulic conductivity in excess of 5 x10-7m/second (i.e. a permeability >50 millidarcies).Empirical evidence suggests that average linear velocities would be of the order of 60 m/day if the backfill has the grain size of a fine sand. The proposed gold lixiviant would probably be an alkaline or ammonium thiosulphate, not cyanide. The resultant sulphate-rich ground and drainage waters could probably be processed using existing purification techniques to produce gypsum and magnesium/calcium carbonate. Within the next 100 years it is inevitable that solution mining will find widespread application on the Witwatersrand, if not for gold extraction, then certainly for water remediation purposes.

Jan 1, 2009

By I. Mihajlovic

This paper investigates a potential method for arsenic removal from copper concentrates using hypochlorite leaching. The problems concerning pyrometallurgical processing of copper concentrates with high arsenic contents are discussed. A possible solution to the problem by leaching of natural enargite crystals with sodium hypochlorite under alkaline oxidizing conditions, with enargite converted into crystalline CuO and the soluble arsenic forming AsO43-, was experimentally investigated and results are presented. Kinetic parameters were calculated for enargite leaching, using a model-free approach. Advanced isoconversional methods were used to investigate the dependence of activation energy (Ea) on reaction rate (a). Keywords Enargite, copper concentrate, isoconversional method, kinetics, activation energy.

Jan 1, 2011

By C. Chingwaru, W. Chingwaru, J. Vidmar

"Zimbabwe is endowed with rich deposits of minerals such as diamonds, platinum, coal, uranium, lithium, gold, antimony, iron, and chrome. Bioleaching has been implemented as an efficient and low-cost method to extract metals such as copper, cobalt, and gold from sulphide and/or ironcontaining ores and mineral concentrates in a number of countries around the globe. Zimbabwe, despite being a world leader in mineral wealth, has gone through years of economic stagnation which have brought with them energy shortages. Bioleaching is an innovative way to recover minerals from ores using relatively low-capital-cost and non-polluting technology. Principally, iron- and sulphur-oxidizing bacteria can be used to oxidize iron and sulphide to ferric iron and sulphuric acid, respectively, and the ferric iron oxidizes the insoluble metal sulphides to soluble metal sulphates that can be readily recovered from solution. Although some minerals such as gold are inert to biological reactions, they can be liberated using bacteria that act on certain types of ores and other minerals that co-occur with these minerals. The geology of the mineralized areas in Zimbabwe, rich in chalcopyrite / pyrite, allows a number of microorganisms to be used for the extraction of minerals by bio-oxidation. This paper reviews the potential of bioleaching in the country. IntroductionZimbabwe has rich deposits of minerals including diamonds, platinum, coal, uranium, lithium, gold, antimony, iron, and chrome. Bioleaching is defined as the use of microorganisms to facilitate the extraction of metals from sulphide or iron-containing ores or concentrates (Rawlings, 2004, 1997). Bioleaching has been shown to be an efficient (Blowes, Ptacek, and Jurjovec, 2003; Nordstrom and Southam, 1997; Schippers, 2004) and low-cost (Schippers et al., 2010) method to extract minerals in many countries around the globe. For example, aerobic Fe(II)- and sulphur-oxidizing bacteria have been shown to be up to two orders of magnitude more efficient in the oxidation of pyrite than the chemical processes (Blowes, Ptacek, and Jurjovec, 2003; Nordstrom and Southam, 1997; Schippers, 2004). Additionally, bioleaching can be used to extract minerals from low-grade ores, sulphidic waste rock dumps, and tailings efficiently (Schippers et al., 2010)."

Jan 1, 2017

This paper considers the probability of the occurrence of potential rockfals in deep-level gold mines where there is point support (props, pipesticks, and timber sticks). The investigation described gave rise to the following implications: natural joints subparalel to the direction of strike have a controlling influence on the potential occurrence of rockfals; with discrete types of support such as props at typical sparings, there is a significant probability of the occurence of potential rockfals; the use of headboards oriented in the direction of strike reduces the probability; and loss of support from a prop increases the probability.

Jan 1, 1989

"Coal seam gas problems can adversely affect the safety and productivity of underground coal mines, leading to fatalities and financial losses. Conventional gas management technologies using ventilation and gas drainage are unable to deal with the high and irregular gas emissions associated with high-production longwall mining. New technologies need to be developed to supplement the traditional gas management techniques to minimize the hazard of coal seam gas. Thin spray-on liners (TSLs) have gained some success for rock surface support since their introduction to the mining industry. Due to their relatively low permeability and appropriate mechanical properties, TSLs also show potential to be used as a gas management tool in underground coal mines.In this paper we review the current gas management challenges and discuss the potential use of TSLs as a gas management tool in underground coal mines. This may involve reducing gas migration into the excavations/roadways, enhancing in-seam gas drainage, and preventing spontaneous combustion. Some potential areas for future research work are identified. IntroductionWhen a coal seam is influenced by mining activities, gas stored inside is liberated into the underground ventilation system. Gas emissions have created serious difficulties for the coal mining industry around the world. Therefore, coal mines have to develop effective strategies to control the gas concentration below the threshold value to meet statutory requirements. Ventilation has been the first solution in gas management for underground coal mining. When the emitted gas cannot be effectively diluted by ventilated air, gas drainage using pre- and/or post-drainage has to be introduced. However, even with ventilation and gas drainage, irregular gas emissions usually increase the gas concentration in roadways and slow down the development rate, thus causing significant economic loss to the coal mining industry (Thakur, 2006). Therefore, new technologies need to be developed to address this issue and mitigate the explosion risk."

Jan 1, 2016

By Willem Le Roux

1.1 Section 47(1) of the Mine Health and Safety Act, 29 of 1996 (?the MHSA?) establishes a Mine Health and Safety Inspectorate which is administered by the Chief Inspector of Mines. The Mine Health and Safety Inspectorate is part of the Department of Mineral Resources. The Chief Inspector is appointed by the Minister of Mineral Resources (see section 48(1) of the MHSA). 1.2 The Chief Inspector must, amongst other things, ensure that the provisions of the MHSA are complied with and enforced, and that all the duties imposed upon the Chief Inspector and the other Inspectors of Mines in terms of the MHSA and any other law are performed. The Chief Inspector of Mines must appoint Principal Inspectors of Mines and Inspectors of Mines to assist him/her to discharge his/her duties (see section 49(1)(a) and (c) of the MHSA).

Jan 1, 2011

By D. J. Mourant

Day-to-day operations on the Broken Hill mine of the Black Mountain Mineral Development (BMMD) Company require a detailed knowledge of the distribution of the ore minerals within the orebody. The data are acquired by systematic underground diamond drilling of the orebody and subsequent geological and analytical borehole logging. These data are then captured onto a database, available for further analysis. Before mining commences in a mining block, copper, lead, zinc, silver and bismuth assay values, and the specific gravity of each sample, are extracted from the database. 3-dimensional variogram and kriging calculations are performed for each geological zone; for all the metals of interest. A computer representation of the mining block in the form of an ore model is then built using these kriged data. From these ore models information is extracted as required by the Geology Department on the mine, and used in numerous operations. These include: daily grade control to supply optimum feed grades to the treatment plant; the compilation of short, medium and long term production schedules; orebody outline definitions for the detailed planning of mining operations; ore resource calculations. The system has been modified and updated since its inception and provides timely information in a production environment.

Jan 1, 1987

By M. E. Rossi

All large-scale applications of conditional simulations intend to benefit from the ‘correct’ (or’ accurate’) characterization of uncertainty, adequately describing the variability observed from the data and its impact on the final objective. This paper discusses a number of relevant issues that highlight the extent to which, in reality, a model of uncertainty is dependent on the random function model chosen. Often in the presence of large number of conditioning data most available random function models will provide similar models of uncertainty. When conditioning is scarce, the resulting models of uncertainty will vary more widely, since the final output will depend mostly on the underlying assumptions of the model chosen. The application described in this paper is taken from a large porphyry Cu operation in northern Chile, and it demonstrates the impact of several variables on the resulting models of uncertainty. In particular, some of the decisions involved include the number of conditioning data and the underlying Random Function model used (Gaussian or indicator-based). Also, implementation-specific parameters must be decided upon, such as grid size used, random number generator, simple or ordinary kriging, multiple-grid simulation, and simulation of irregular three-dimensional bodies (as opposed to regular grids). Some practical guidelines are proposed to deal with these decisions.

Jan 1, 2003

The excavation of ramps and tunnels often requires high-speed development with (or without) the use of high-energy mining equipment such as loaders, dump trucks, TBMs and roadheaders. This high-speed development creates a challenge in terms of providing a safe and productive working environment. For example, heat from continuously exposed surrounding rock, heat from broken rock, heat generated by mining equipment, potential in flows of hot ground water, pollution from associated diesel equipment and the distance of the advancing face from fresh through-ventilation all have to be taken into account when designing ventilation systems for high-speed ramp and tunnel developments. This paper discusses methods of achieving acceptable environments at the face and along the length of the tunnel. The methodology has been successfully implemented in the development of long (up to 20 km) TBM drives in the Lesotho Highlands Project and in mining projects in hot rock using drill and blast methods as well as mechanized methods using continuous miners and roadheaders. The determination of heat loads includes calculation of the heat flow within the surrounding rock, evaluation of the operating cycle of the equipment and the contribution to the overall heat load of the broken rock as it travels out of the tunnel. The determination of heat loads from surrounding rock in new tunnels required a modification of the algorithms generally used for established excavations. The paper also examines the use of, for example, mobile duct and fan systems to ensure that fresh air is delivered to the specific areas where workers are located.

Jan 1, 2000