Search Documents

By G. Apsey

Eutectic freeze crystallization (EFC) is a novel technique for the recovery of pure salt and pure water from hypersaline waste brines. It is therefore a promising technology for the treatment of industrial waste waters. The impurities caused by crystallizing salt out of multi-component brines by EFC have not yet been investigated, however. To these ends, the selenium impurity found in sodium sulphate, produced from the waste brine of a platinum operation, was investigated. It was believed that the similarity between sulphate and selenate ions allowed isomorphous substitution of selenate ions into the sodium sulphate crystals, which was the likely cause of impurity uptake. It was found that the presence of sodium chloride in the industrial brine promotes the uptake of selenium, while ionic strength of the brine and mass deposition rate of sodium sulphate did not have a significant effect on the selenium uptake. Isomorphous substitution is predicted to be the most significant mechanism by which all impurities will be taken up when applying EFC to other industrial waste brines.

Jan 1, 2013

By J. Fu

"Since it was first identified in 1817, selenium has received considerable interest. Native selenium and a few selenium minerals were discovered several decades later. With the increasing number of selenium minerals, the occurrence of selenium minerals became the focus of much research. A great number of selenium deposits were reported all over the world, although few independent selenium deposits were discovered. Selenium is obtained mainly as a byproduct of other metals, and is produced primarily from the anode mud of copper refineries. This paper presents a comprehensive review of selenium minerals, as well as the treatment of copper refinery anode slimes for the recovery of selenium. Our focus is on the selenium minerals, including their discovery and occurrence, and the distribution of selenium resources. In addition, the main methods of recovering selenium from copper anode slimes are summarized. IntroductionSelenium (Se) was first observed in 1817 in a laboratory (Greenwood et al., 1984). The discovery of selenium was made by the Swedish chemist J.J. Berzelius and J.G. Gahn, who isolated selenium from a red residue in sulphuric acid from pyrite mined at Fahlun, Sweden. Selenium was named from the Greek word selene (moon), since it resembled tellurium, which had been discovered a few years earlier and named from the Latin word tellus (Earth).After the first observation of selenium in the laboratory, selenium received considerable interest. In 1954, E.P. Kaiser pointed out that Se is enriched in sulphide ores and often associated with Bi, Co, Sn etc. (Kaiser 1954). In 1959, Hawley and Nichol investigated selenium in Canadian sulphide minerals, and presented the content of selenium in sulphide from several deposits of different types. They also proposed that Se is enriched in lowtemperature hydrothermal pyrite (Hawley and Nichol, 1959). The thermodynamic conditions for forming native selenium and selenium minerals in sedimentary rocks were discussed, as well as geochemical behaviour of selenium near the oxidation zones of sulphides in the 1970s (Howard III, 1977; Zhu et al., 2003). Zhu et al. examined the morphology, features, and genesis of native selenium from Yutangba, Enshi City, Hubei Province, China in 2004, and pointed out, from the different forms of native Se, that selenium can be activated,transformed, remobilized, and enriched at sites such as in the unsaturated subsurface zone or in the saturated zone (Zhu et al., 2005). The transport and deposition of selenium in felsic volcanic-hosted massive sulphide deposits of the Yukon Territory, Canada was studied and reported by Layton- Matthews et al. (2005)."

Jan 1, 2016

By Z. Levinson, R. Dimitrakopoulos

A mining complex is an engineering system where raw materials are extracted from several mines, processed, transported, and sold to the market. The uncertainty and local variability of material grades and their locations within the related mineral deposits are critical for determining the optimal life-of-mine extraction sequence, destination policy, operating modes, and capital investment decisions, which define the production schedule of a mining complex. Infill drilling is used to further characterise a mineral deposit and reveals information that changes the representation of the resource model and potentially the resulting optimal long-term production schedule. A self-learning reinforcement learning approach is proposed to determine the optimal drilling locations that maximise the net-present value of the long-term production schedule and the associated financial forecasts by adapting the schedule to additional information. A case study at a copper mining complex demonstrates a $70 M increase in project value by collecting drilling information with a $1 M budget.

Sep 1, 2021

By F. Agterberg

In his 1978 monograph ‘Lognormal-de Wijsian Geostatistics for Ore Evaluation’, Professor Danie Krige emphasized the scale-independence of gold and uranium determinations in the Witwatersrand goldfields. It was later established in nonlinear process theory that the original model of de Wijs used by Krige was the earliest example of a multifractal generated by a multiplicative cascade process. Its end product is an assemblage of chemical element concentration values for blocks that are both lognormally distributed and spatially correlated. Variants of de Wijsian geostatistics had already been used by Professor Georges Matheron to explain Krige’s original formula for the relationship between the block variances as well as permanence of frequency distributions for element concentration in blocks of different sizes. Further extensions of this basic approach are concerned with modelling the three-parameter lognormal distribution, the ‘sampling error’, as well as the ‘nugget effect’ and ‘range’ in variogram modelling. This paper is mainly a review of recent multifractal theory, which throws new light on the original findings by Professor Krige on self-similarity of gold and uranium patterns at different scales for blocks of ore by (a) generalizing the original model of de Wijs to account for random cuts; (b) using an accelerated dispersion model to explain the appearance of a third parameter in the lognormal distribution of Witwatersrand gold determinations; and (c) considering that Krige’s sampling error is caused by shape differences between single ore sections and reef areas.

Jan 1, 2015

By W. K. Brisden

The SAG Milling Seminar, which was held at Murdoch University in Perth on 30th November and 1st December, 1989, was a very successful technical seminar. Organizer Dr Norm Stockton reported a total attendance of 130, which was higher than the 70 expected: 20 delegates came from the eastern States and the remainder were from Western Australia.

Jan 1, 1990

By M. Stachowiak, M. Nowicki, K. Walas, A. Skoczylas, P. Stefaniak

In this paper the authors present a walking robot dedicated to the inspection of a belt conveyor’s transportation system in an underground mine. The developed robot can independently diagnose all of the key rotating elements of the belt conveyor (pulleys, bearings, drums, gears, engines) based on vibration and acoustic signals as well as typical RGB (red, green, blue) and thermal images. The article presents key diagnostic procedures applied to real industrial data obtained during robot testing.The work was developed as part of the ‘THING–subTerranean Haptic INvestiGator’ project. The authors presented the main assumptions of the research methodology developed for the needs of technical diagnostics of conveyor elements typical of inspection work performed by mining staff. Based on industrial data, the use of algorithms for elements such as rollers, drive stations, and the conveyor belt were shown. The main assumption of the research is to develop a robot adapted to the conditions of a deep mine, capable of carrying out an autonomous inspection of mining infrastructure. The conducted tests and the developed fault detection algorithms were aimed at preparing the robot for underground tests in the operating conditions of the mine.

Sep 1, 2021

By H. Ogasawara

To study the preparation process of an earthquake, we should get closer to the hypocentre. In co-operation with ISS International, we had an experimental field (~200 m x~200 m) without dykes and faults in a South African deep gold mine. We have monitored more than 20,000 seismic events (M<2) with borehole tri-axial accelerometers. We used a data acquisition system with 15 kHz sampling and 120-dB dynamic range. In a remnant area at a distance of 100?200 m, an earthquake sequence associated with an M~2 event occurred. Significant changes in seismic parameters such as stress drop, b-value, energy index were observed associated with the sequence. We installed Ishii?s borehole strain meters and could monitor as large a strain change as 10-4associated with mining. However, sampling was only 4 times per hour and 12 bit A/D. A distance from the M2 sequence was ~100 m, being not close enough. Therefore, we found another field with several crosscut tunnels excavated across a fault where an M=2-3 event is expected. We installed the strain meter within several metres of the fault to monitor both shear and normal strains on the fault. The strains are continuously digitized with a 24-bit 25-Hz A/D conversion. The Earth Tide (10-8)is clearly detected. Seismicity induced by longwall mining can be compared to earthquake swarm induced by fluid intrusion to vertical dykes. We also found a decrease in energy index in the source area of M>5events a few days before the major events. Keywords: seismic monitoring, strain monitoring, seismic parameters, preparation process of an earthquake, South African gold mine.

Jan 1, 2002

By Q. G. Reynolds

DC arc furnaces are widely used for steel scrap melting, and are increasingly being used for smelting applications as well. The electrical resistivity of slags varies widely, from highly conductive slags in ilmenite smelting, to highly resistive slags in applications such as cobalt recovery from non-ferrous slags, and nickel laterite smelting. Models have been developed to predict the electrical behaviour of the DC open plasma arc and the molten slag bath. These models allow the voltage and current ranges of furnace power supplies to be specified.

Jan 1, 2004

A Seminar to discuss &apos;Reactivity of Line in Steel Making&apos; was held in the auditorium of Iscor&apos;s Headquarters Building in Pretoria on the 5th August, 1971. The Institute organised this Seminar on the occasion of the visit of Dr Obst of the Rheinische Kalkstein Werke GMBH, Wuelfrath, West Germany. The latter is one of the largest lime companies in the world and Dr Obst is in charge of their research laboratory. He and his co-workers have earned a reputation for their research into reactivity of lime in steel making. This work is also of great importance to the steel industry in this country, particularly with the changes which are occurring with the introduction of basic oxygen furnaces. Some 80 persons representing most of the major steel companies attended this Seminar. Dr Obst presented his most interesting paper which he illustrated with projector slides. This paper is printed in full in this journal. This was followed by several contributions and active discussions. The first contribution was made by Dr T. B. Beeton of the Research and Development Department, Iscor. He gave a brief summary of the studies on reactive lime carried out at Iscor since 1968. Their work was particularly related to the selection and definition of the various reactivity tests and the correlation of these with plant results. He demonstrated that the DIN methods, particularly the Din (40°) test, gave the best results and reported that good agreement had been reached between Iscor, Highveld and Northern Lime on future test procedures. Mr B. Lowther of The Northern Lime Company then dealt with problems associated with the production of high reactive lime. The rotary kilns at The Northern Lime plant at Lime Acres are particularly suitable for the production of high-reactive lime, because this type of kiln lends itself to accurate control of temperatures and retention times. Several problems, however, exist. Because of the long haul distances and the deterioration of reactive lime by absorption of CO2 and water, high reactive lime is not suitable for most customers. To constantly be changing kiln conditions to produce relatively small quantities of high-reactive lime, therefore, causes problems. Highveld Steel at present is the only company requiring high-reactive lime and a satisfactory product is now being produced at a cost because kiln capacity is reduced and fuel costs are higher. Dr P. R. Jochens, of the National Institute for Metallurgy then submitted data to show how the reactivity of soft burnt reactive lime deteriorated due to long railage hauls. Detailed sampling of trucks had been carried out leaving the lime works and on receipt at Highveld and it was demonstrated that there was deterioration in the top layers of the truck. This top layer protected the balance of the lime which is still in good condition on arrival at Highveld. Exposure to atmosphere by further handling and storage into the bunkers at Highveld, however, resulted in further severe deterioration in the lime reactivity and the lime when finally fed to the Basic Oxygen Furnace is reduced to one third to one quarter of the original reactivity value. The same deterioration does not occur with normal run of kiln lime, which is burnt harder, but still has a satisfactory reactivity for most purposes. Mr A. A. Hejja of the Department of Metallurgy, Witwatersrand University then made a contribution on the metallurgical aspects of the use of lime of different reactivities in the Basic Oxygen Furnace and the effect on desulphurization efficiencies. He gave a wealth of data on actual tests which had been carried out and came up with the surprising conclusion that the deterioration of high-reactive lime due to transport did not have as serious an effect on the efficiency of desulphurization as one would have expected. The efficiency was good provided high-reactive lime in the first instance had been produced, irrespective of whether it had deteriorated thereafter. Poor efficiency was obtained only when the lime in the first instance was produced in an unreactive form. The temperature rise in the Basic Oxygen Furnace also has a definite effect. If lime is introduced when the temperature is too high, soft burnt reactive lime becomes hard burnt and unreactive before it can dissolve in the slag. Use of ferromanganese slag assists dissolution of lime. There was a great deal of discussion following these contributions. Particular interest was expres8ed in the special lime described by Dr Obst. This consists of a mixture of fine lime which is premixed with fluxes and either briquetted or pelletised. The question of injecting finely ground lime as an alternative was also discussed. Both these systems eliminate the necessity for highly reactive lime. With smaller lime particles, larger surfaces are exposed thereby ensuring more rapid dissolution in the molten slag. The discussions generally were lively and informative and all present derived benefit from learning of the experiences of others. The valuable contribution made by our German visitor, Dr Obst, was particularly appreciated. The instantaneous English-German translation service which was provided, greatly facilitated discussions.

By S. Escoffier, A. Giraud, K. Su, F. Homand, N. Hoteit

Abstract For the feasibility study of an underground waste disposal the characterization of the coupled behaviour of the host rock is required: Because of the very low permeability of these formations few experimental data are generally available. In this framework the uses of the sensitivity studies could orient the experimental efforts by highlighting the key parameters of the formation. This paper gives a first approach of the sensitivity studies performed with probabilistic methods in the geomechanical field. A one dimensional model which characterizes the thermohydromechanical response of an argillaceous rock to the excavation of a waste canister site and its setting up, is considered. Zusammenfassun Die Machbarkeitsstudie eines tiefliegenden Endlagers für radioaktive Abfälle beinhaltet die Untersuchung des gekoppelten Verhaltens des im Lagerbereich anstehenden Gesteins. Aufgrund der sehr geringen Wasserdurchlässigkeit dieser Formationen liegen häufig nur wenige experimentelle Angaben vor. Die Verwendung von Sensibilitätsstudien kann in diesem Zusammenhang als Hilfsmittel zur Entscheidungsfindung dienen. Dabei sollen die maßgeblichen Eigenschaften der Formation festgestellt werden, anhand derer der Umfang der experimentellen Erkundung festgelegt werden kann. Dieser Artikel stellt einen ersten Ansatz zur Durchführung von Sensibilitätsstudien mittels einer mechanisch-probablistischen Kopplung im Bereich der Geomechanik sowie die Vorteile gegenüber Parameterstudien vor. Zur Abbildung des thermohydromechanischen Stoffverhaltens von tonigem Fels während der Schachterstellung und der Einlagerung der Abfälle wird ein eindimensionales Model verwendet. Résumé L&apos;étude de faisabilité d&apos;un centre de stockage de déchets radioactifs en profondeur passe par la caractérisation du comportement couplé de la roche hôte. Du fait de la très faible perméabilité de ces formations, souvent peu de données expérimentales sont disponibles. Dans ce cadre l&apos;utilisation d&apos;études de sensibilité permettrait d&apos;orienter les efforts expérimentaux en faisant ressortir les caractéristiques primordiales de la formation. Cet article présente une première approche de la réalisation d&apos;études de sensibilités à l&apos;aide de couplages mécano-fiabilistes dans le domaine de la géomécanique. Un model unidimensionnel caractérisant la réponse thermohydromécanique d&apos;une roche argileuse au creusement d&apos;un puit de stockage et à la mise en place de conteneurs de déchets est considéré.

Jan 1, 2003

By B. E. Ydstie, B. F. Lund, K. R. Løvåsen, B. A. Foss

The paper presents sensitivity analysis for a dynamic model of submerged arc silicon furnaces. The model we study, called ?Simod?, was developed by Elkem in cooperation with NTNU and Sintef. It is today a much used tool in Elkem for operator training and analysis of the dynamic behaviour of the silicon production process. The aim of our work is to bring the simulator tool closer to industrial practice, and construct a mechanism to adapt the model to the behaviour of a running process, online. The paper presents the results of the sensitivity analysis that has been undertaken for important parameters in the Simod model. The parameters associated with the process inputs are electric power loss, loss of fixed C and reactivity of carbon. The output signals that have been investigated are fed quartz, tapped silicon and silica. The paper also interprets the results of the sensitivity analysis in a process operation context.

Jan 1, 2004

By M. J. Kanda, T. R. Stacey

Thin spray-on liners (TSLs) have been used as sealants and rock support in tunnels for over 25 years. Laboratory tests have indicated satisfactory properties that can provide adequate strength, adhesion, toughness, and elasticity as part of rock support systems in mining excavations. These characteristics are, however, not always demonstrated in practice, when mine environmental conditions do not correspond with laboratory environmental conditions. The shortcomings of TSLs experienced in the mining industry have raised concerns, resulting in scepticism from some operators regarding their utilization. The research described in this paper aims to investigate TSL performance in environmental conditions similar to those experienced in mines. Brazilian indirect tensile (BIT) specimens were prepared from precast shotcrete and coated with TSLs. The specimens were then exposed to different environmental conditions for up to 112 days before BIT testing under various conditions: laboratory room temperature and humidity; saturated room temperature; and combined saturated and high temperature (50°C). Additional uncoated shotcrete and TSL BIT specimens were prepared for comparison purposes. The results of the BIT tests showed that environmental conditions have a significant influence on the tensile strength enhancement of shotcrete by TSLs. Water-based TSLs are most likely to be suitable for high humidity environments, although their performance decreases at higher temperatures. Numerical modelling of TSL-coated BIT samples confirms the potential limitations of designing TSL support based only on laboratory testing carried out under room conditions.

Jul 1, 2021

By C. J. Van Niekerk

The study comprised of the investigation into the sensitization characteristics of AISI 409 titanium stabilized ferritic stainless steel during low heat input welding. AISI 409 is a fully ferritic stainless steel used in catalytic converters and tubing for automotive exhaust systems due to the supposition that sensitization does not occur during low heat input welding. Two plates of 2 and 4 mm were tested for sensitization during low heat input welding. The study confirmed that chromium carbide (M23C6) precipitation occurs on the grain boundaries in the heat-affected zone with consequent depletion of Cr adjacent to the grain boundaries during welding. In the 2 mm plate sensitization occurred in the heat input range of 0.1 kJ/mm to above 0.25 kJ/mm and in the 4 mm plate sensitization occurred in the heat input range of 0.2 to 0.9 kJ/mm. Ti stabilization is ineffective at the heat inputs used in this investigation due to the rapid cooling rate through the temperature region where TiC precipitates. The presence of N was found to be detrimental since it consumes Ti on cooling, forming TiN, effectively lowering the amount of Ti available for TiC formation during rapid cooling after welding. Annealing for 5 minutes at 725°C does not improve the sensitization characteristics of the welded plate. There is a linear increase in grain size as heat input increases. The resistance to pitting corrosion decreases in the sensitized, welded plate in theheat-affected zone adjacent to the fusion line of welding. Keywords AISI 409 ferritic stainless steel, sensitization, grain growth, resistance to pitting corrosion, low heat input welding.

Jan 1, 2011

The possibility that type 430 stainless steel can become sensitized during annealing after hot-rolling was studied by simulated cycles of continuous-annealing heat treatments, and by calculation of the carbon solubility. It was found that the lower-carbon steel could be sensitized at lower annealing temperatures than the higher-carbon steel, which is in line with plant experience. The difference in sensitization behaviour is ascribed to the lower rate of recovery of the lower-carbon steel during cooling, since recovery is sensitive to the grain size. At practical heat-treatment temperatures, austenite formation does not play a role.

Jan 1, 1996

By C. Bergmann, V. Ross

The concept of underground ore processing, in which valuable ore and waste are separated at a coarse particle size to improve the economics of operations and minimise the environmental impact, seems attractive from a sustainability perspective. Perceived benefits of such an operation include energy and cost savings due to a reduced hoisting load, a reduced footprint of surface operations, and using material for backfill that has not been contaminated by process chemicals. Progress in the South African mining industry in this area has however been below expectation, and opportunities for underground processing in deep, narrow reef operations were therefore explored by an Excel-based simulation with sensor-based sorting (SBS) as concentration technology. Various PGM mining scenarios incorporating factors such as the mining rate, depth of operation, and effects of dilution and particle size on the metallurgical efficiency, were compared. Whilst these initial results can be regarded as indicative only, they have shown that the economics of such an operation are driven by selective mining at significantly higher rates than achievable with conventional methods. Also, the cost of preparing, conveying and placing rock backfill will need to be lower than that of hoisting waste and depositing it on a surface dump. Another aspect to be addressed is whether ore sorting machines would be able to operate under harsh conditions underground and what provision would need to be made to ensure their efficient operation. Further investigations should focus on refining costs, incorporating environmental considerations in the modelling of economics and sustainability, and compare greenfields with brownfield scenarios. Keywords: Ore sorting, hoisting, backfill, mining rate, economics simulation

Jan 1, 2020

By D. van der Westhuizen, H. Krieg, M. Kruger

In the field of Fischer-Tropsch synthesis catalysts, cobalt, platinum, and aluminium are the primary metal constituents of the conventionally used cobalt catalyst. While platinum recovery remains a focal point in this field, a recent endeavour by a South African company emerged, which aimed to recover cobalt and aluminium from spent Fischer-Tropsch synthesis catalysts for potential use in the agricultural sector. This study aimed to optimally separate cobalt and aluminium from spent Fischer-Tropsch synthesis catalyst for this purpose. It further leverages the OLI database to predict metal speciation during solvent extraction to aid with experimental planning. Shake-out tests were conducted to determine optimal separation. conditions, which were validated using three distinct methods: (i) evaluating the experimental error, (ii) comparing results with similar research, and (iii) validating results against the OLI database. The investigation revealed the pivotal role of the aqueous pH yielding effective separation at pH 3.13 ([H2SO4] = 2.5 × 10−4 M) when using 20 vol.% CYANEX 272 and 50 mol.% pre-neutralisation. Effective cobalt scrubbing was achieved with 50 g/L Al at pH 2.8, while successful stripping required 1 M H2SO4. Competitive interactions between complexing aluminium and cobalt species were observed when contacting with CYANEX 272 at a pH < 4. Equipment design analysis for a targeted separation efficiency of 87% dictated the necessity of two mixer stages and a settler measuring 1.5 m × 1.5 m × 6.0 m (height × width × length). This settler would ensure sufficient residence time for gravity separation at a flow rate of 10 m3/h.

May 27, 2025

By R. J. Kriek, J. J. Cruywagen, W. J. Engelbrecht

Selective photo reduction, using the semiconductor TiO2 under UV irradiation, has been investigated as a possible recovery and/or separation method for the PGM&apos;s rhodium, palladium and platinum. The effect of pH value and concentration of the sacrificial reducing agent (ethanol) on the rate of reduction of Rh (III), Pd (II) and Pt(IV) ions have been determined separately for these ions as well as for some mixtures. Conditions favourable for the reduction and adsorption (or precipitation) on TiO2 have been established. It has been found that already deposited Pt or Pd metal promotes reduction of Rh (III) ions at a pH value where it would not otherwise be reduced. A method for the separation of a mixture comprising Rh (III), Pd(II) and Pt (IV), based on photo reduction and adsorption on the TiO2, is proposed.

Jan 1, 1995

By N. Moemise, M. B. Shongwe, P. A. Olubambi, M. M. Ramakokovhu

"Near-infrared (NIR) spectroscopy sorting technology is incorporated in an automated optical mineral sorter that can discriminate between materials using the differences in characteristics when exposed to near-infrared radiation. During September 2014 to April 2015, a pilot plant that utilized NIR technology to discriminate between kimberlite and waste materials was commissioned to determine the viability of including this technology in the diamond winning process flow sheet at Cullinan Diamond Mine. The plant was used to minimize the waste content in the size fraction -70+35 mm that reports to the crushing section and then to the dense media separation process. This paper describes the initial test work, conducted at Mintek, that led to the decision to conduct a pilot-scale study. The mineralogical characterization of the feed and product streams to establish the sorting criteria and the operational data obtained during the pilot plant campaign are described. The results indicated a good possibility of discriminating between the kimberlite and waste material using NIR technology. However, the consistency of discrimination was not good enough to avoid the risk of potential diamond loss. Furthermore, a lower than expected availability of the machine reduced the throughput capabilities. IntroductionUsing near-infrared spectroscopy (NIRS) technology for ore sorting is a new concept for the mineral processing and mining industry. NIRS has been used for decades in the laboratory for the identification of pure minerals, and has its roots in the recycling, food, and pharmaceutical industries (Salter and Wyatt, 1991; Robben et al., 2009). Ore sorting in itself is not a new concept; it was introduced during the Stone Age with handsorting being the first method to separate valuable materials from gangue (Wills and Napier-Munn, 2006; Sassos, 1985). However, over the years the scale of mining has increased and hand-sorting has become challenging to implement (Joensson, 2014).Sensor-based sorting is an advanced technology that can help overcome problems such as ore dilution experienced in mineral processing operations. The benefits are lower energy and water costs, reduced ore dilution, lower environmental impact, and improved profit margin (Mathew, 1974; Jonsson, 2014; Salter and Wyatt, 2009; Death et al., 2009). In sensor-based sorting, materials are mechanically sorted based on certain physical properties that are detected by a sensor (Dalm, 2013). Research has found that with NIR scanners it is possible to obtain a ‘fingerprint’ of a sample that is directly related to its mineralogical composition. According to Woutruba et al. (2009), molecules absorb NIR radiation by means of electronic and vibrational transitions. Nowadays, there are many sensors available in the market that utilize different material properties; the choice of a sensor is dependent on the mineralogy of the ore."

Jan 1, 2016

By A. C. du Preez

The separation of nickel and cobalt from calcium, magnesium and manganese by solvent extraction using synergistic mixtures of carboxylic acids was studied. Addition of certain viable synergists to commercially available tertiary branched carboxylic acids, such as Versatic 10 (Shell) or Neodecanoic acid (Exxon), produced large synergistic shifts (?pH50) in the pH50values for nickel, and small antagonistic shifts (negative ?pH50values) in the extraction of calcium. Under the initial test conditions used (0.50 M each of Neodecanoic acid and the Mintek synergist, in xylene) a large separation (pH50Ca? pH50Ni= 3.09 pH units) between nickel and calcium in their extraction from 1.00 M sodium nitrate solutions was obtained, compared with only 1.11 pH units in the absence of the synergist. The selectivity series for the extraction of divalent base metals from 0.333 M sodium sulphate solutions by 0.50 M Neodecanoic acid and 0.25 M of the Mintek synergist in C12-C13aliphatic diluent was found to lie in the order (with pH50values in parentheses): Cu(3.42) > Ni (5.08) > Zn (5.58) > Co (5.73) > Mn (6.62) > Ca (7.48) >Mg (8.25). In batch counter current experiments, a simulated leach liquor containing (in gL-1): Ni 5, Mg 5, Mn 2, Co 0.5, Ca 0.5, Cu 0.1and Zn 0.1 was contacted with the mixed extractant in three stages at unit phase ratio and an equilibrium pH of 5.9. The recovery of nickel was 99.9 per cent and that of cobalt was 84.7 per cent, whilst the co-extractions of manganese, calcium and magnesium were 2.7,1.5 and 0.04 per cent, respectively. The recovery of cobalt can be enhanced by employing a slightly higher pH, although this will also increase the extraction of manganese, calcium and magnesium somewhat. Nearly quantitative stripping (99 per cent) of nickel from the loaded organic phase was achieved in a single contact at an organic-to-aqueous phase ratio of 4 using a simulated spent electrolyte containing 39 gL-1sulphuric acid and 33 gL-1nickel,thereby producing an ?advance electrolyte? containing 57 gL-1nickelat pH 3.5. Loading of acid into the organic phase was very slight, amounting to only 0.002 M H+in contact with the above-mentioned spent electrolyte. Keywords: solvent extraction; synergism; nickel; calcium; carboxylic acids.

Jan 1, 2004

By J. He

The separation performance of a raw coal sample from South Africa based on the dense gas-solid fluidized bed beneficiation technique was investigated. Analysis showed that the raw coal sample distributes mainly in the -50+6 mm size range with the -1.6 g/cm3 density fraction accounting for 78.20% of the cumulative mass distribution. A flow sheet of the sequential coal beneficiation technique was introduced. The experimental and simulation results of the hydromechanical and density distribution stability indicate that the dense gas-solid fluidized bed could provide a stable separation environment with uniform density fluctuations under suitable operating conditions. With the application of this technique on the raw coal sample, the separation results show that three products, consisting of 73.25% clean coal with an ash content of 9.59%, 11.31% middlings, and 15.44% gangue were effectively separated at two different densities of 1.82 g/cm3 and 1.57 g/cm3. This study provides an effective flow sheet for achieving the high-efficiency separation performance on raw coal from arid areas. Keywords dense gas-solid fluidized bed, dry coal beneficiation, density distribution, separation efficiency.

Jul 1, 2013