Search Documents

By A. Kijko, C. W. Funk

Methods for the analysis of seismic hazards in mines are reviewed as illustrations of the techniques that are being used in some South African mines. The classical parameters that describe a hazard are the seismic activity rate, ?, the Gutenberg-Richter value, b, and, occasionally, the maximum regional magnitude, mmax The activity rate is calculated readily owing to the inherent simplicity of its definition. The evaluation method presented for the Gutenberg-Richter b value takes into account the presence of mmax Three statistical procedures are described for the assessment of mmax which the maximum observed magnitude, Xmax a crucial role. Often, the configuration of mine seismic networks is changed, or the networks are improved, which inevitably gives rise to changes in the completeness of the seismic catalogues. The routine analysis of seismic hazards must account for these time dependent changes. A method for the evaluation of hazards is reviewed that accommodates varying levels of quality in the catalogues. Finally, the concept of the volume of ground motion (VGM) is presented. This is a technique that allows for most aspects of seismic hazards in mines. The advantage of the VGM is that a hazard can be described by one physically significant value: the volume of rock (cumulated over a time period) in which the ground motion exceeds some critical particle velocity. Data from the gold mining region in South Africa known as the Far West Rand is used in a demonstration of the discussed methods of hazard analysis.

Jan 1, 1994

By J. H. van Dalen, P. J. Brandt, F. W. Wessels

A maximum of ten process streams (Merrill barren solutions) can be monitored sequentially with this on-line analyser, and gold concentrations as Iow as 0,005 mg/I can be determined. The design is a further development of the Tell-tale analyser constructed by the Corner House Laboratories during the period 1965-69. The barren solution is preconcentrated automatically by solvent extraction, the solvent being a solution of I per cent Aliquat 336 in di-isobutyl ketone. An aqueous-to-solvent ratio of 40: I is maintained. The extracted gold in the organic phase is determined by flame atomic absorption, each analysis taking approximately II minutes. The long-term reproducibility of the absorbance readings over a 24-hour period of repetitive sampling of four simulated process streams varied from 6,9 to 4,1 per cent relative standard deviation for gold concentrations of 0,0 I to 0,05 mg/I.

Jan 1, 1980

By A. Mitchell

On 25 August 2011, Andrew Mitchell, Lucas Moalusi, and Matthew van der Want of Bell Dewar hosted a presentation on Mining and Communities in Mooinooi, in the North-West Province. The conference was attended by traditional leaders in the North-West Province, officials from the Department of Local Government and Traditional Affairs, and executives from the mining industry. The presentation concerned traditional governance in mining, communities? rights in terms of applicable legislation, and the corporatization of community affairs.

Jan 1, 2012

By Org de Wet

This paper summarises the strategy for selection between a two module coal plant incorporating large, but less equipment, and a three module coal plant with more but smaller equipment. The two options were evaluated in terms of three main categories: ? Size ? size of the equipment and the effect on the process efficiency as well as the difference in physical dimensions of the plant to accommodate the larger equipment; ? Cost ? capital savings between a two and a three module plant, processing the same ROM (run-of-mine) tons per hour (t/hr); and ? Practicality ? in terms of constructability of the plant, safety of using larger equipment and maintainability of the equipment. Decisions that were taken to reduce the risk associated with size, cost and practicality on the chosen option of a two module plant will be highlighted.

Jan 1, 2006

By A. A. Bradley, K. H. Stanton, P. J. D. Lloyd

A theory for the dynamic balancing of centrifugal mills is presented that takes account of the mass and shape of the charge in a gyrated grinding tube and the way in which the charge lags behind the centrifugal force vector. predicts that a corresponding lag in the angular position of the counterweight centres of mass is necessary, and that the fractional filling should be increased if the ratio of gyration diameter to tube diameter is decreased. A worked example is given for a I MW centrifugal mill that was balanced adequately by the methods described.

Jan 1, 1983

By D. H. Diering

Definition of mineral resources and reserves forms the basis for effective mine planning and reliable public reporting of mineral assets. Historically the mineral resource and reserves declaration process has been the domain of the geology and surveying disciplines, with the declaration of the reserves by the surveyor being based on the application of modifying factors to the declared resources available for mining. As part of an ongoing process to improve efficiency, reliability, and reproducibility of results, this approach has been revised and enhanced through the introduction of a revised process and reconciliation tools. The revised approach to reserve definition is based on the definition of scheduled resources, at an appropriate confidence estimate in the context of an approved business plan, over the anticipated life of the mineral asset being applied to define reserves. This planning and scheduling is developed, during the annual business planning process, by the mine planning department using tools such as CADSMine?. The scheduled area together with the application of revised modifying factors is tabulated in the BME (basic mine equation) and reflects the mine production plan over time. Simplification of the modifying factors to dilution and losses underpins the simple yet robust approach to improved definition of reserves in this process and in the basic resource to reserve equation (BR2RE). Dilution intrinsically affects grade but not metal content, whereas the losses reflect both the efficiency of mining and planning and are reflected in metal losses, area losses, or both. Reconciliation of the derived ?resource converted to reserve? area, (which is based on the business plan from CADSMine?), versus the ?resource available for mining?, (which is derived from Datamine?), underpins the robustness and auditability of the reserves declaration. This R&R accounting and reconciliation approach is transparent and facilitates interrogation of the logic and rationale of long-term business planning and project strategy. These numbers are processed and reported in the logic of the basic resource equation (BRE), which also addresses aspects such as white areas (future and historic), tail management, and partial extraction (non-scheduled pillars, etc.) in compliance with SAMREC definitions. Areas that do not have the necessary confidence and data support to be declared as resources find their space as pre-resource (outside the domain of public reporting), outlining existing potential for future extraction and reporting. Use of the BRE leads ultimately to a complete, refined accounting and reconciliation-oriented approach for all production entities. The revised resource and reserve process includes the discipline of mine planning as intrinsic to the definition and declaration of resources and reserves. Subsequent to the change in process, the resources and reserves have truly become the domain of the mineral resource management discipline. This paper defines the logic of the basic resource equations and outlines their application in the definition and reconciliation of mineral resources and reserves at Anglo American Platinum Limited.

Jan 1, 2012

By D. H. Diering

Definition of mineral resources and reserves forms the basis for effective mine planning and reliable public reporting of mineral assets. Historically, the mineral resource and reserves declaration process has been the domain of the geology and surveying disciplines, with the declaration of the reserves by the surveyor being based on the application of modifying factors to the declared resources available for mining. As part of an ongoing process to improve efficiency, reliability, and reproducibility of results, this approach has been revised and enhanced through the introduction of a revised process and reconciliation tools. The revised approach to reserve definition is based on the definition of scheduled resources, at an appropriate confidence estimate in the context of an approved business plan, over the anticipated life of the mineral asset being applied to define reserves. This planning and scheduling is developed, during the annual business planning process, by the mine planning department using tools such as CADSMine?. The scheduled area together with the application of revised modifying factors is tabulated in the BME (basic mine equation) and reflects the mine production plan over time. Simplification of the modifying factors to dilution and losses underpins the simple yet robust approach to improved definition of reserves in this process and in the basic resource to reserve equation (BR2RE). Dilution intrinsically affects grade but not metal content, whereas the losses reflect both the efficiency of mining and planning and are reflected in metal losses, area losses, or both. Reconciliation of the derived 'resource converted to reserve' area (which is based on the business plan from CADSMine?) versus the 'resource available for mining' (which is derived from Datamine?) underpins the robustness and auditability of the reserves declaration. This R&R accounting and reconciliation approach is transparent and facilitates interrogation of the logic and rationale of long-term business planning and project strategy. These numbers are processed and reported in the logic of the basic resource equation (BRE), which also addresses aspects such as white areas (future and historic), tail management, and partial extraction (non-scheduled pillars, etc.) in compliance with SAMREC definitions. Areas that do not have the necessary confidence and data support to be declared as resources find their space as pre-resource (outside the domain of public reporting), outlining existing potential for future extraction and reporting. Use of the BRE leads ultimately to a complete, refined accounting and reconciliation-oriented approach for all production entities. The revised resource and reserve process includes the discipline of mine planning as intrinsic to the definition and declaration of resources and reserves. Subsequent to the change in process, the resources and reserves have truly become the domain of the mineral resource management discipline. This paper defines the logic of the basic resource equations and outlines their application in the definition and reconciliation of mineral resources and reserves at Anglo American Platinum Limited.

Jan 1, 2013

By L. S. Belyayeva, A. S. Chumak, N. N. Boyko, A. V. Bondarenko

Analysis of results of many years concerned study of the fire hazard parameters of the material of the mine conveyor belts come in for use at the mines of the Ukraine in 1984-2002 that was carried out in the laboratories of the Scientific-Research Institute of Mine-Rescue Work is adduced in the paper. The basic tendencies on raising the fire safety of the conveyor belts that are retraced in their world production are shown.

Jan 1, 2003

By L. Nell

Bateman, like other engineering contractors, carries out or participates in many studies of potential projects in the Minerals Industry. This paper aims to explain the contracting approach to feasibility studies as practiced by Bateman, particularly where this differs from a traditional mining company approach. A brief description is provided of the usual phases of a project and the types of estimate needed to proceed from one phase to the next. Possible organizational structures involving different forms of association between owner, contractor and consultants are then outlined. The bulk of the paper then demonstrates that the cost estimates prepared stem directly from the mining plan, metallurgical process design and engineering design philosophy. The steps to be followed in order to prepare a credible estimate which accurately reflects the design constraints are described. The importance and the methodology of carrying out value engineering and of preparing contingency estimates based on a thorough risk analysis exercise are then discussed. Financial modelling techniques are described briefly. The paper concludes with short summary case studies of two recent investigations of potential projects in Africa.

Jan 1, 1999

By S. Kamalpour

It has been observed that the productivity of ferromanganese furnaces, and the stability of metal and slag compositions, vary considerably according to the type of coke used as reductant. However, the desired properties of coke for optimum furnace performance are not well understood. In this investigation, the behaviour of four cokes, which exhibited a wide range of performance in ferromanganese production, was investigated by means of laboratory simulations of reducing conditions in the furnace. The Stationary Charge in Controlled Environment (SCICE) technique was used to simulate the conditions in the furnace shaft. Batches of raw materials, mixed in the same proportions as used in practice, were heated at fixed rates to 900, 1100 and 1300°C then cooled. The mass loss was used as a measure of the degree of reduction. Conditions in the lower part of the furnace were simulated by means of melt-reduction experiments in which lumps of coke were drilled out to form crucibles in which enriched ferromanganese slags were reduced at 1500 and 1550°C then cooled. An examination of the raw materials and the cooled, reacted charges using a variety of analytical and characterization techniques enabled the sequence of reaction and changes in morphology of the raw materials to be followed. This enabled an understanding of the behaviour of the cokes during reduction to be developed, which was then used to explain the observed performance of the cokes in practice. By relating the observed behaviour of the cokes in the laboratory tests to measurable properties of the unreacted cokes and to their observed performance in practice, it was shown that to achieve high productivity and good furnace performance, cokes should be selected to have moderately high reactivity towards CO2 (Boudouard reactivity) relative to conventional iron blast furnace cokes.

Jan 1, 2004

A reliable laboratory method to characterize the response of free gold particles to flash flotation conditions has been developed. The test has been performed on free milling gold ores as well as synthetic ores, using either a gravity concentrate or gold powder as the gold source, to assess the floatability of gold particles. Trends in free gold flotation kinetics, as well as size and milling effects, were identified for gold recovery based on the different feed types, reagent dosages, and residence times. It was shown that the ultimate recoveries and kinetic trends of gold particles from the gravity concentrate could be enhanced with increased dosage of collector, potassium amyl xanthate. Interestingly, in comparison to gravity-recoverable gold, recovery from pure Au powders was better in collectorless flotation, and cumulative recovery decreased with higher levels of collector addition. Improved coarse particle recovery appeared linked to increased collector additions for both the gravity concentrate and the pure gold powders. In general, coarse gold particles demonstrated slower kinetic rates thaen the fine or intermediate components incomparable tests.

Jan 1, 2015

By P. den Hoed, J. Nell

Tests were conducted on samples of rutile, titaniferous slag and ilmenite; each sample was mixed with coke and chlorinated in a bubbling fluidized bed at 1000°C. Profiles of the rates of chlorination of species were constructed from chemical compositions of the bed residues at different durations. From the start FeO and MnO are chlorinated quickly and all but entirely in a fraction of the time it takes to chlorinate all the TiO2. When the level of FeO is significant, as in slag and ilmenite, FeO is chlorinated faster than TiO2is. In these oxides, there is an inverse relationship between the rates of chlorination of FeO and TiO2during this first stage; the relationship, moreover, correlates linearly with the initial percentage of FeO in the oxide. We identify three stages in the chlorination process; a first, in slag and ilmenite, when FeO is being chlorinated; a second, when TiO2is most readily chlorinated; and a third, towards the end, when the levels of TiO2are reduced to those of other species. The rates at which individual species are chlorinated are analysed in terms of their appreciation or depreciation with respect toTiO2

Jan 1, 2003

By J. R. de Wet

The behaviour of mild steel in aqueous cyanide solutions similar to caustic cyanide elution solutions was investigated at high temperature in electrochemical experiments. The anodic polarization diagrams of mild steel indicated that steel may undergo active dissolution under these conditions. The rare occurrence of gold plating in practice is the result of the limiting of the anodic dissolution of the steel by the presence of a passive layer on the steel. This passive layer is stable only in a certain potential range, and the free corrosion potential attained determines whether the steel will be passive or active. For conditions typical of elution columns, several corrosion potentials are possible, depending primarily on the initial condition of the steel and the concentration of oxygen in the solution. If these conditions result in the formation of a passive layer on the steel, changes in concentration and temperature will not necessarily result in plating since the layer may exist in a metastable form.

Jan 1, 1993

By G. M. Bentel, G. E. Blight

The environmentally acceptable disposal of fine-particled mining and industrial wastes by the formation of hydraulic- fill slimes dams is becoming an increasingly important aspect of the total mining endeavour. Relatively little is known of the behaviour of waste slurries during deposition. This paper describes and analyses the following aspects of slurry behaviour: (i) the relationship between viscosity, shear strength, and water content, (ii) the slope assumed by a thickened slurry, (iii) particle-size sorting on a hydraulicfill beach, (iv) gradients of hydraulic-fill beaches, and (v) internal erosion during the deposition of slurry. v083n04p073.pdf

Jan 1, 1983

By A. J. Lynch, N. W. Johnson, D. J. McKee, G. C. Thorne

The behaviour of minerals in sulphide flotation processes, with reference to simulation and control. by A. J. LYNCH, Ph.D., N. W. JOHNSON, Ph.D., D. J. McKEE, Ph.D., and G. C. THORNE, B.Sc. (Hons.) (Visitors) In sulphide flotation processes, there are two mechanisms by which particles are transferred from the flotation pulp to the concentrate: adhesion to air bubbles and natural flotation, and entrainment in the froth. The entrainment mechanism is particularly important for particles of non-sulphide gangue, which do not absorb collector. The importance of controlling the recovery rate of water was illustrated in plant testwork in which selectivity between valuable sulphides and sulphide gangue, and between valuable sulphides and non-sulphide gangue, was altered by manipulation of variables affecting the water recovery rate. The two mechanisms should be recognized in the development of a control system. Most of the control schemes in operating plants have concentrated on reagent additions, which affect the natural flotation mechanism. Although control of the chemical environment is clearly of paramount importance in flotation, plant tests have shown that control of the variables affecting the entrainment mechanism is also important.

Jan 4, 1974

By S. L. Chen

Keywords: copper, concentrate drying, steam dryer, dryers By placing additional demands on energy and gas flow, the moisture content of a copper concentrate has an adverse effect on the smelting process. Different drying technologies, such as directly heated rotary dryers, flash dryers, and steam dryers, are available to solve this problem. The energy requirements of and off-gas generated from different dryer types are compared. The performance of the steam dryer was found to be superior to that of the others. In particular, the rotary steam dryer and its benefits are discussed. Structural properties confer an advantage on the rotary steam dryer, for wear on tube elements is eliminated, and drying efficiency is improved. If steam is available, the rotary steam dryer is an excellent choice for drying copper concentrates.

Jan 1, 2006

By P. J. van der Walt, P. J. F. Fourie, L. M. Falcon

Various methods for the beneficiation of minus 0,5 mm coal are examined briefly, and tests are described on a cyclone of 150 mm diameter operating with magnetite as the medium. It was found that, for sharp separations, at least 50 per cent of the magnetite should be finer than 1Oµm. At that size, the ash content of the product was about 7 per cent at yields of 59 to 64 per cent, and the loss of medium was reasonable (about I kg per ton of fines treated).

Jan 1, 1980

By M. J. Little

Potgietersrust Platinums Ltd is Anglo Platinum?s only open pit operation and annually extracts 57 million tonnes of rock from 2 open pits. Over the past 3 years ~220 km of exploration drilling has been done, ~1000 km of rock face have been exposed for face mapping and over 7000 laboratory and field tests have been conducted. This has produced large amounts of geotechnical data to be utilised for feasibility studies, initial slope design and ongoing slope optimisation. It was necessary therefore to develop geotechnical databases to manage the vast amounts of data collected. SABLE and MineMapper 3D databases were created for logging and mapping respectively, with rock testing data incorporated into both. A pit inspections database was developed in MS Access and the existing groundwater and slope monitoring database was improved. The databases were linked to AutoCAD and Datamine to ensure that the latest geotechnical data is used for planning, draughting and modelling. The use of geotechnical databases ensures that no data is lost, standards are maintained and analysis can be easily performed. This increases the confidence of the analysis and allows the geotechnical engineers to optimise slope designs and blast designs on a regular basis. This reduces the risk of slope failure thus making the open pits more economical and safe.

Jan 1, 2006

By T. B. S. Giddy

The advantages to be gained from the use of a high-density ion-exchange resin in a uranium recovery circuit are shown. It is concluded that, in existing fluidized-bed plants, the throughput of solution can be increased by up to 40 per cent at the same uranium recovery. Alternatively, the values in the barren solution can be improved at the same flow-rate of solution.

Jan 1, 1980

By M. J. Kahn

A new Scramble has hit the African continent. This Scramble has many drivers: the 1978 Deng Xiao Ping liberalizations in China; the 1989 collapse of the Soviet empire; the ICT revolution; the ease of global communications. The underlying dynamic is the end of the bipolar world of the Cold War and its replacement with multipolarity. According to HSBC (2011), in 2050 China will be the world?s largest economy, with India number 3 and Brazil number 7. Russia will be 15th (below its old rival, Turkey). South Africa maybe ranked 30th, yet has been invited to join the exclusive (BRIC) club. One has to ask, why? It is sad to note how low South Africa is assessed to be?currently it is around number 24 in the world; the reason for the fall is that the HSBC model includes population growth, and it is in this domain that South Africa is a loser, being constrained by the impact of HIV/AIDS on its life expectancy. The original four BRIC nations include the factory of the world (China), the garden of the world (Brazil), the gas station of the world (Russia), and the back office of the world (India). South Africa comes to the club both as jeweller of the world and as gatekeeper. China, Brazil, and Russia all have considerable expertise in mining exploration, extraction, and processing.

Jan 1, 2011