Search Documents

By A. J. Jager, J. A. Ryder, M. U. Ozbay

This paper deals with procedures used for designing pillar systems in hard-rock tabular mines operating at shallow depths, typically less than 1000 m. A comprehensive review if current practice identifies four types if pillars, namely non-yield, yield, crush and barrier pillars, and the main principles for designing these pillars are outlined. It is shown that the current design methods for pillar systems in South Africa are mainly empirical, each mine developing its pillar-design methods based largely on practical experience. This results in varying pillar layouts, even between neighbouring mines, despite similarities in geology, and depth if mining. It is suggested that some current layouts may fall short if being the best as regards safety, the maximum safe extraction percentages, or flexibility in accommodating future mining scenarios in deeper or otherwise different geological conditions.

Jan 1, 1995

By R. W. O. Kersten

This paper describes the method used at Agnes Gold Mine in the calculation of pillar strengths, which involves a back-analysis type of approach. The results obtained there are comparable with those obtained by accepted formulae for pillar strength. It was found that a stress level of 70 MPa for the width of combined pillars (Le. crown and sill pillars) causes failure of the reef drives as well as the tops and bottoms of the stope side walls. As shrinkage stoping to depths of more than 650 m would result in very low percentage extractions, alternative methods of stoping will have to be investigated for these depths.

Jan 1, 1984

An evaluation was made of the wear and performance characteristics of liter bars, and the cost-life effectiveness of backing materials for rotary-mil liners. In a large run-of-mine mil in which the liter bars were mounted on grid liners of austenitic manganese steel (AMS), the liners had an average life that was five to six times that of equivalent unprotected liners. For a single mil, this is equivalent to annual savings in the cost of materials of up to R320 000, and to a downtime of 100 hours. Of the five materials tested in a large pebble mil grinding quartzitic ore, AMS grids and 'white iron' blocks performed best on a cost-life basis, with possibly improved performance from a real white cast iron. (The 'white iron' was shown by microstructural analysis to contain flake raphite and pearlite, being in reality a grey cast iron.) The high-chromium white iron had by far the longest predicted life, with mild steel a surprising second. Rubber was shown to last well in this type of mil. The wear rates of liners change during their lifetimes. The protective effect of liter bars was clearly illustrated by the reduction of over 40 per cent in the wear rates of the liners when the lifter bars were renewed to a height of 80 mm from a fully worn height of 35 mm.

Jan 1, 1991

By S. J. Bluhm

Recommendations are given for the design of multi-stage spray chambers in which air flows horizontally through water sprays. A detailed description is given of one such spray chamber at Hartebeestfontein gold mine that is used for bulk cooling of the incoming ventilation air, and that has been constructed according to these recommendations. A method for predicting the performance parameters of horizontal multi-stage spray chambers is given, and the method is illustrated with some examples. The method is equally applicable to spray chambers in which the water, rather than the air, is cooled.

Jan 1, 1979

By D. F. Malan

This paper gives an overview of the difficulties associated with determining the strength of hard-rock pillars. Although a number of pillar design tools are available, pillar collapses still occur. Recent examples of large-scale pillar collapses in South Africa suggest that these were caused by weak partings that traversed the pillars. Currently two different methods are used to determine the strength of pillars, namely, empirical equations derived from back analyses of failed and stable cases, and numerical modelling tools using appropriate failure criteria. The paper illustrates that both techniques have their limitations and additional work is required to obtain a better understanding of pillar strength. Empirical methods based on observations of pillar behaviour in a given geotechnical setting are popular and easy to use, but care should be exercised that the results are not inappropriately extrapolated beyond the environment in which they are established. An example is the Hedley and Grant formula (derived for the Canadian uranium mines), which has been used for many years in the South African platinum and chrome mines (albeit with some adaptation of the K-value). Very few collapses have been reported in South Africa for layouts designed using this formula, suggesting that in some cases it might yield estimates of pillar strength that are too conservative. As an alternative, some engineers strongly advocate the use of numerical techniques to determine pillar strength. A close examination unfortunately reveals that these techniques also rely on many assumptions. An area where numerical modelling is invaluable, however, is in determining pillar stresses accurately and for studying specific pillar failure mechanisms, such as the influence of weak partings on pillar strength. In conclusion, it appears that neither empirical techniques nor numerical modelling can be used solely to provide a solid basis for conducting pillar design. It is therefore recommended that both these techniques should be utilized to obtain the best possible insight into a given design problem. Owing to the uncertainties regarding pillar strength and loading stiffness, monitoring in trial mining sections and in established mining areas is also an essential tool to test the stability of pillar layouts in particular geotechnical areas.

Jan 1, 2011

By A. H. Swart, M. F. Handley

Unplanned stope panel collapses occur on most near-surface and shallow mines in South Africa. Although these incidents often occur during blasting, they pose a major threat to the safety of underground workers and the economic extraction of orebodies. Most stope panel collapses occur due to excessive panel lengths that are not designed according to a systematic design procedure or methodology. Instead, panel lengths are often dictated by the equipment in use and by previous experience under similar conditions. Hence, a rock engineering design methodology for the design of stable stope panels between pillars is of vital importance for optimum safety and production in shallow mining operations. Using the proposed design methodology described in this paper, rock mechanics practitioners and mine planners should be able to identify and quantify the critical factors influencing the stability of stope panels. The critical factors should then be used as input to the design of stable stope panels that will provide the necessary safe environment for underground personnel working in stopes. The proposed design methodology is an iterative process, which includes aspects such as rock mass characterization, estimation of rock mass properties, identification of potential failure modes, consideration of appropriate stability analyses and other elements of the rock engineering design process. This process continues after implementation. During monitoring, new data should be included in the database and the design process repeated on a regular basis. Design approaches included in the proposed design methodology include empirical methods such as different rock mass classification methods, analytical methods such as elastic and Voussoir beam analyses, kinematic analyses, probabilistic analyses, and numerical analyses. Keywords: stability, stope panels, design methodology, hard rock mines, shallow mining operations

Jan 1, 2004

By A. H. Swart

Unplanned stope panel collapses occur on most near-surface and shallow mines in South Africa. Although these incidents often occur during blasting, they pose a major threat to the safety of underground workers and the economic extraction of orebodies. Most stope panel collapses occur due to excessive panel lengths (resulting in excessive stope spans) that are not designed according to a systematic design procedure or methodology. Instead, panel lengths are often dictated by the equipment in use and by previous experience under similar conditions. Hence, a rock engineering design methodology for the design of stable stope panels between pillars is of vital importance for optimum safety and production in shallow mining operations. Using the proposed design methodology described in this paper, rock mechanics practitioners and mine planners should be able to identify and quantify the critical factors influencing the stability of stope panels. The critical factors should then be used as input to the design of stable stope panels that will provide the necessary safe environment for underground personnel working in stopes. The proposed design methodology is an iterative process, which includes aspects such as rock mass characterization, estimation of rock mass properties, identification of potential failure modes, consideration of appropriate stability analyses and other elements of the rock engineering design process. This process continues after implementation. During monitoring, new data should be included in the database and the design process repeated on a regular basis. Design approaches included in the proposed design methodology include empirical methods such as different rock mass classification methods, analytical methods such as elastic and Voussoir beam analyses, kinematic analyses, probabilistic analyses, and numerical analyses. Keywords: stability, stope panels, design methodology, hardrock mines, shallow mining operations

Jan 1, 2005

By C. R. Speers

The induced elastic stresses in the sidewalls of gold-mining tunnels at a depth of 4000 m in the Witwatersrand exceed the peak compressive strength of even the best-quality quartzite rocks. Laboratory tests measuring post-yield stress versus strain response show that brittle fracture occurs, followed by a loss in strength associated with strain-softening behaviour. Numerical modeling based on an assumed Mohr-Coulomb criterion fitted to the test results shows that large ongoing deformations of the sidewall occur, leading to total tunnel failure without adequate support. A methodology is presented to enable a quick assessment to be made of support requirements in terms of ground characteristic curves for numerically derived pressure versus displacement. From these curves, estimates can be made of the force levels for cable bolting and of the thickness and strength requirements for shotcrete linings. As an example of its application, the methodology is used in a comparison of the relative stability efficiencies of a square-shaped tunnel and a horizontal ellipse-shaped tunnel.

Jan 1, 1996

By A. Whillier

Recommendations are given for the design of vertical cooling towers for use underground in mines and a method is given for predicting the entering and leaving water temperatures when a given amount of heat has to be dissipated.

By J. L. Taylor, E. B. Viljoen, W. M. Craig, A. M. McIntosh

The Chemwes uranium plant treats old gold-plant residues from the Sttifontein and Buffelsfontein Gold Mines by acid leaching, belt filtration, countercurrent ion exchange (ClX), and Bufflex solvent extraction (SX). The uranium is recovered by precipitation as ammonium diuranate. Absorption and elution in the CIX section are achieved in four NIMCIX columns operating as two parallel streams. Each loading column is 4,85 m in diameter and contains 12 absorption stages. The elution columns are 3 m in diameter and contain 8 stages. The eluant used is 10 per cent sulphuric acid at ambient temperature. During the commissioning and initial operating periods reported here, the plant yielded an average barren solution of 1,6 p.p.m. of U3O8 from a feed with a mean U3O8 concentration of 132 p.p.m. The U3O8 concentrations in the barren solution were better than 2 p.p.m. some 85 per cent of the time, and better than I p.p.m.73 per cent of the time. Investigations are underway to institute an automatic control system that will result in the U3O8 values on the resin and in the barren solution being maintained at or near the target values in spite of changes in the concentration of uranium in the feed solution.

Jan 1, 1982

By A. J. Van Rensburg, N. B. Strydom, C. H. Van Graan

The design, construction, and use of a practical ice-jacket for miners by N. B. STRYDOM, Ph.D. (Illinois) (Fellow), D. MITCHELL, Ph.D. (Rand) (Member), A. J. VAN RENSBURG, M.Sc (Poteh) (Visitor), and C. H. VAN GRAAN, M.Sc (Pretoria) (Visitor) Microclimate suits have been shown to be very effective in decreasing physiological strain in hot, wet environments, thus enabling men to work without risk in areas that would normally carry a high risk of heat stroke. In this paper, some design considerations in the development of the frozen jacket are described. Water complied with most of the desirable properties required of a coolant material for use In a microclimate suit. The Human Sciences Laboratory has developed a jacket in which ice is used as the coolant and which is designed according to the most acceptable anthropometrical characteristics. The jacket consists of an inner poncho-type waistcoat containing 28 water compartments. Over this is worn an insulating jacket, which minimizes warming of the coolant by the environment. Suitable refrigeration units have been developed to freeze the jackets underground. Laboratory tests have shown that these jackets are effective for about 2,5 hours, Irrespective of the wet-bulb environment, when men are working at a moderate rate. Jackets should, however, be used only in environments in which the wet-bulb temperature is in the range of 32,S0 to 35,S °C.

Jan 9, 1974

By B. G. Meyburgh

SYNOPSIS As a result of a test programme over a period of approximately ten years and a decision to extend the uranium plant, it was decided to design and erect the first full-scale Purlex Plant in the Republic of South Africa. The plant at Buffelsfontein G.M. Co. Ltd. was commissioned in August, 1968, and to date has produced results superior to those predicted in the original estimates. The capital expenditure was R678 000 for a plant capable of treating 1 600 gallons per minute of pregnant solution. Compared with the conventional resin ion exchange process, it has been found that the saving in production costs is 21 cents per pound U3O8 produced. The amine loss is 10 parts per million, which is equivalent to a total organic loss of 250 parts per million. The uranium loss in the raffinate is less than 0.001 g/l U3O8. The final product is of a high quality and it is probable that it is pure enough to convert to the fluoride directly.

By B. G. Meyburgh

E. H. D. Carman: The results achieved at Buffelsfontein Gold Mining Company Limited are very encouraging and it seems certain that as far as the conventional uranium recovery process is concerned solvent extraction must entirely supplant the old resin ion exchange process. The operational costs given by Mr Meyburgh indicate that the chief cost items in solvent extraction are reagents. In other words 38.4 per cent of the operational cost at Buffelsfontein is due to the replacement of the organics lost from the plant. It is reported from a wide field of experience that loss, particularly of amine, is a direct function both of the quantity and nature of finely divided suspended solids in the pregnant solution and the extent to which the design of the mixers causes the formation of secondary dispersions which do not easily separate in the settler. There is in addition the unavoidable loss of amine due to its solubility in the aqueous solution which is thought to be about 4 p.p.m. In order to minimise solvent losses therefore, efficient clarification at the head of the solvent extraction plant would appear to be a most important requirement. For this reason the newly erected plant at West Driefontein Gold Mining Company Limited has two Funda Pressure Filters each with a filtering area of 540 sq. ft. which are together designed to handle up to 440 g.p.m. of filtrate. This plant has not yet been commissioned but preliminary testing indicates that suspended solids in the sub micron size range which do not settle even on protracted standing of the solution, will rapidly blind the clarifiers. This should not affect solution clarity but frequent backwashing adds to the cost of precoating. The difficulty was countered in the laboratory with continuous additions of filter aid in addition to the precoat but, as Table 11shows, cost of filter aid is high and its use will have to be optimized against organic losses due to less efficient clarification. This will need much careful observation over a relatively long period of time. Costs shown in Table 11 are based on Mr Meyburgh's figures adjusted to probable conditions at West Driefontein Gold Mining Company Limited. The assumption based on small scale testing is that it will cost 5.2c/ton in filter aid to clarify filtrate to a level of about 5 p.p.m. of suspended solids, in order to restrict the amine loss to 10 p.p.m. which is likely to be equivalent to an entrained organic loss worth approximately only 2.6 cents per ton. Of course poor clarification as mentioned earlier is only one of two or even more causes of organic losses and it seems obvious on the above basis that the operation and economics of pressure clarification will need close investigation. A second important consideration at West Driefontein has been the design of the pump-mixers which must perform the dual function of phase mixing and providing the necessary hydraulic gradient for counter current flow of the two phases. The arrangement is shown in Fig. 1.

Jan 10, 1970

By P. E. Venteer

The Grootegeluk coal-processing plant treats 3 kt of raw coal per hour to produce a middlings fuel coal and a coking coal fraction with ash contents of 35 and 10 per cent respectively. The plus 0,5 mm fraction is treated by heavy-medium processes, the final top size of the coal being 15 mm. About 400 t of minus 0,5 mm coal per hour is subjected to froth flotation. The routes originally considered for the processing of this fine coal were froth flotation, shaking tables, heavy-medium cyclones, and water only cyclones in combination with froth flotation. The results from tests on the fines arising from a small-trial open-cast mine are discussed. When the froth flotation route was decided upon, further tests were conducted on the selection of the equipment most suited to the particular requirements of this coal and the rest of the plant. Tests using different types of flotation cells and dewatering equipment are discussed. During the commissioning, several operational problems were encountered, and the work done to find the best solutions is discussed.

Jan 1, 1984

This is a sampling of the papers presented at the conference, the proceedings can be bought from the SAIMM The technique reported here involves measuring the air pressures generated within sealed boreholes located behind blasts. Results from twelve free face blasts in competent rock environments a represented. There were no instances of high pressure gas penetration, even at distances corresponding to less than one blast burden. Rapidly generated underpressures were measured in most holes, with the magnitudes of the peak pressures decreasing with distance behind the blasts. It has been proposed that the under pressures are the result of new volume created due to crack formation and overall rock mass dilation. The experimental evidence is consistent with this, including a correspondence of the onset times of the peak underpressures with the nominal firing times of the nearest blastholes. New post-blast cracks were observed when using borehole video cameras in the monitoring holes. A calculation of new volume produced within the monitoring holes is proposed as an indicator of damage. While the data exhibit considerable scatter, there is a power function dependence on scaled distance, which resembles that of typical vibration data. The data also lie within the normally quoted vibration regimes for rock damage and are consistent with measured extents of damage. It is concluded that this technique may provide an inexpensive and practical comparative measure of near-field rock damage due to blasting. It is further concluded that gas penetration is not a common phenomenon. Damage appears to be mainly attributable to the nearest blastholes and the control of charge mass in perimeter blastholes is emphasized for damage minimization.

Jan 1, 2000

By M. B. Algeo, R. H. A. Plaistowe

A method of forecasting the haulage trucks required for a large open-pit operation is described. Emphasis is placed on the effects of changes in planning and on the complexities of a mining operation that involves many benches and dumping areas.

Jan 1, 1979

By S. M. Graham, G. Mellis

"The determination of the oxidation state(s) of an element present in a solid sample may be required for a number of reasons, including the assessment of the degree of reduction which has taken place during a multi-step production of a metal. In addition, possible flaws in a metal may result from small amounts of oxides included in the solid. The analyte of interest may be present as a major component of a sample of interest, or as a minor impurity - beneficial or requiring removal - in another matrix.Numerous methods have been established for the analysis of species in solution samples - for example, Fe2+ and Fe3+ by titration, Cr6+ by colourimetric means, etc. With appropriate knowledge of the solution being analysed, many of these methods are fairly straightforward, extremely reproducible and accurate. In those instances where the analyte in a solution is known to be in only one form, the analysis is even more straightforward, since it can be achieved instrumentally (by AAS, rCP-OES or rCP-MS, for example).However, the situation with respect to the analysis of solids is not as simple. Various techniques - such as X-ray diffraction - are routinely used by our mineralogists to obtain information about the various minerals present in solid samples, and thus about the oxidation states of the analyte elements present. However, these techniques usually give results that are qualitative, or semi-quantitative at best. They are also usually time-consuming and expensive. One of our colleagues at Mintek, Deshenthree Chetty, has done extensive work in developing a method for the quantification of manganese species in solids using mineralogical methods, and this is no small achievement."

Jan 1, 2014

Ground control problems in the form of large dome or wedge collapses have been experienced at Tau Lekoa Mine since production began. Crush pillars in various configurations have been used and through a process of trial and error the current pillar layout has been derived. A strike pillar layout is used and additional mid-panel pillars are left spaced a maximum of 10m or 16m apart, depending on conditions and mining direction. Pillar spacing is based on an empirical relationship between fallout height and pillar spans. Analysis of the spatial distribution of large falls of ground indicates that there may be several geotechnical relationships contributing to stable pillar spans. The current focus is to define the relationship between geotechnical areas and hangingwall stability so that area specific support strategies can be formulated that could result in increased production efficiencies. Depuis le début de la production, la mine Tau Lekoa a connu des problèmes de contrôle au sol, sous la forme d’effondrements de grands dômes ou coins. Des piliers d’écrasement, dans des configurations variées, ont été utilisés et une série d’essais a résulté en la disposition de piliers en cours. Une configuration de piliers de direction est utilisée, et des piliers mi-panneau supplémentaires sont laissés, espacés d’un maximum de 10m ou 16m, selon les conditions et la direction de la mine. L’espacement des piliers est établi sur une relation empirique entre la hauteur des retombées et les intervalles entre piliers. L’analyse de la distribution spatiale de grandes tombées de terrain indique qu’il peut y avoir plusieurs relations géotechniques qui contribuent à des intervalles de piliers stables. L’intérêt présent est de définir la relation entre les zones géotechniques et la stabilité du toit, pour pouvoir formuler des stratégies de support spécifiques à un endroit, ce qui entraînerait des accroissements de production. Bodenkontrollprobleme traten seit Produktionsbeginn in Form von grossen Keil oder Dachhaubenbrüchen in der Tau Lekoa Mine auf. Bruchpfeiler in verschiedensten Konfigurationen wurden verwendet und auf Grund empirischer Fakten wurde das gegenwärtige Pfeilerlayout abgeleitet. Ein Layout für Strukturpfeiler wird verwendet und zusätzliche mittig situierte Pfeiler in einem Maximalabstand von 10m bis 16m installiert, abhängig von den Konditionen und der Vortriebsrichtung.Der Pfeilerabstand basiert auf dem empirischen Verhältnis Fallhöhe und Pfeilerspannweite. Die Analyse der räumlichen Verteilung großer Bodenabsenkungen deutet an, daß es einige geotechnische Verhältnisse geben kann, die zu stabilen Pfostenspannweiten beitragen. Der gegenwärtige Fokus soll das Verhältnis zwischen geotechnischen Bereichen und Stollendeckenstabilität definieren, damit bereichspezifische Unterstützungsstrategien formuliert werden können, welche in erhöhter Produktionsleistung resultieren könnten.

Jan 1, 2003

By A. L. Hinde, A. A. Bradley, P. J. Lloyd

The results of slow crushing tests in a stiff testing machine for both small and large step reductions of particle size are given. The energy consumption required to produce a given weight of minus 74 um material was determined when both single-crystal quartz and Witwatersrand reef were crushed. For comparison the two materials tested were also comminuted in a ball mill under optimum conditions. There are indications that slow crushing under stiff conditions is the most efficient method of breakage that can be devised. The comparison with ball milling results thus yields a value for the efficiency of ball milling of approximately 80 per cent. These results confirm that the best current estimates of milling efficiency, which are based on the free boundary surface energy of the material being milled, are probably too low by at least one order of magnitude.

By D. P. Roberts

This paper reviews the use of crush pillars on mines in the Bushveld Complex and the Witwatersrand Supergroup. Stress measurements were undertaken in order to determine the residual strength of these crush pillars. The results from these stress measurements are compared with previous attempts to determine the residual strength of crush pillars using back analysis. It is concluded that the residual strength of such crush pillars lies in a band between 13 MPa and 25MPa. Using the data from the stress measurements, as well as published and unpublished data, a stress-strain curve for a crush pillar with a width-to-height ratio of 2:1 is proposed. Where further work is required, this is indicated in the text.

Jan 1, 2005