Search Documents

The comments by Mr Chaston were constructive and much appreciated. Considering firstly the recovery of cassiterite from fine deslimed material. A size distribution analysis shows that 58 per cent of cassiterite in Union Tin flotation concentrate reports in the minus 15 micron (quartz) size range. This is achieved at a recovery of 67 per cent and concentrate grade of 42,6 per cent. It is of interest to note that at Altenberg in East Germany 85 per cent of the tin in deslimed minus 43 micron material is recovered into a 14 to 16 per cent Sn concentrate using para-tolyl arsonic acid as collector. Reconcentration of this material is then carried out using two shaking table stages which recover 53 per cent of the tin in a 50 per cent Sn concentrate. Flotation was resorted to after recovery rates of 35 per cent and concentrate grade of 30 per cent had been achieved in a 275 ton per day plant comprising 130 tables. Tests on tabling of deslimed minus 43 micron material have not been carried out at Union Tin. The cost of equipment actually associated with cassiterite flotation amounts to about R60 000. The

By M. R. Henzen, J. W. Funke, G. J. Stander

SYNOPSIS The adverse effect of acidic mine drainage derived from gold and coal mining operations on the quality of receiving waters is described, together with measures to be taken to counteract this pollution. The mineral load and the toxic effects from metallurgical and metal finishing industries are also considered. Attention is drawn to water conservation aspects.

The Institute was founded in 1894 as the Chemical and Metallurgical Society of South Africa. In 1904 it was reconstituted as the Chemical Metallurgical and Mining Society of South Africa and in 1956 it became the South African Institute of Mining and Metallurgy. The objects of the Institute are to advance the science and practice of mining and metallurgy, to afford opportunities for the interchange and recording of knowledge of mining and metallurgy and to ensure high standards of professional conduct and competence. Membership benefits include monthly issues of the Journal of the Institute, monthly General Meetings at which papers are read, symposia, excursions to mining and industrial concerns and the use of club facilities at Kelvin House. Technical journals received on an exchange basis are available to members at the Johannesburg Public Library. The current membership of the Institute is over 1,600. Membership applications are accepted from suitably qualified persons and the requirements for entrance to the various grades of membership are summarised below. Fellows shall not be less than 30 years of age, shall be university graduates in pure or applied science or shall produce evidence to the satisfaction of the Council that they have successfully completed a co-ordinated course of study in pure or applied science of at least three years' duration at an approved university or institution deemed by the Council to be of equivalent status. Members shall have been employed in senior technical positions in important mining or metallurgical undertakings for at least five years or they shall have practised as mining or metallurgical consultants for at least five years. They shall be practising their profession at the time of application. Entrance fee R10.00, Annual subscription R17.00. Letters of designation: F.S.A.I.M.M. Members shall be not less than 25 years of age and shall be university graduates in pure or applied science, or shall have successfully completed co-ordinated courses of study in pure or applied science of at least three years' duration. They shall have been engaged in work of an approved technical character in the mining or metallurgical industries, of which not less than two years shall have been in positions of responsibility. A candidate shall be practising his profession at the time of his application. Entrance fee R8.00, Annual subscription R15.00. Letters of designation: M.S.A.I.M.M. Associates shall be not less than twenty-five years of age, and shall have been engaged in positions of responsibility in, or associated with, the mining or metallurgical industries for periods of not less than three years. If, however, the candidate for admission to the higher grade of Associate, is at the time of his application, already a Student, he need satisfy the Council only that he is, at the time of his application, engaged in a position of responsibility in or associated with the mining or metallurgical industries. In all cases the applicants shall satisfy the Council that they are fit and proper persons to become Associates. Entrance fee R8.00, Annual subscription R15.00. Graduates shall be not less than 21 years of age and shall be university graduates in pure or applied science, or have completed co-ordinated courses of study in pure or applied science of at least three years' duration at an approved university or institution. They shall not remain Graduate members after attaining the age of 30 years without the permission of Council. Entrance fee R2.00, Annual subscription R10.00. Students shall be persons not less than 18 years of age who are being educated or trained in a manner approved by the Council, to occupy a technical position in or associated with the mining or metallurgical industries and who, furthermore, shall not have attained the qualification required for a higher grade of membership. They may remain Students until they have obtained the necessary qualifications for transfer to a higher grade of membership, but not after the end of the Institute's financial year in which they attain the age of 28 (twenty-eight) years. They shall then transfer to a higher grade to retain membership of the Institute. The Council may relax the provisions of this clause in such cases as it considers appropriate. Entrance fee nil; Annual subscription R3.00. Other. The Council has the power to elect to the grade of Fellow or Member, candidates who may not fulfil all the requirements for entrance to these grades but whose status, professional achievements and practical experience in mining or metallurgy justify such election. Applications. Requests for membership application forms should be addressed on the attached form to the Secretary, South African Institute of Mining and Metallurgy, P.O. Box 61019, Marshalltown, Transvaal.

By E. B. Viljoen

I. R. M. Chaston* As a gravity concentration man in the midst of so many eminent flotation experts I feel like Daniel. However, I would respectifully disagree with the opening remarks by Mr Viljoen. First, he suggested that gravity concentration of cassiterite was not effective in sizes below 30 microns. In a paper to the Institution of Mining and Metallurgy in 19621, I gave some figures for gravity concentration of deslimed material both for cassiterite and for wolfram which indicated that careful shaking table concentration of fine deslimed material could give recoveries of 75 to 90 percent in the size ranges above 13 micron. These were figures obtained from normal plant operation. It would be interesting to know if any tests were carried out on gravity concentration of the efficiently deslimed feed to this flotation plant to see what the recovery would be. Secondly, Mr Viljoen suggested that gravity concentration plants were expensive. He gives the cost of a flotation plant at R300 000 to treat a feed of 400 t.p.d. to the desliming section or 160 t.p.d. to the flotation cells. From his operating cost figures it would appear that the flotation cost is approximately R2 to R4 per ton of feed to flotation and the total operating cost about R2 per ton of feed. A table plant to treat this tonnage of deslimed feed would consist of about 30 tables and should cost considerably less to install and very much less to operate than the flotation plant. Third, Mr. Viljoen suggests that the concentrate grade from a gravity concentration operation would be unacceptably low. The paper quoted abovel showed that once a primary fine concentrate had been made, giving a suitably deslimed material, further gravity concentration could give concentrates of over 40 per cent Sn with high recoveries. Tailing from this dressing stage was naturally returned to the feed. To give these high grades, sulphides had been removed by flotation but this necessary flotation step is simple and cheap to operate and could be restricted to the final stage when the quantities involved are small. I would agree that flotation has a part to play in fine tin recovery but this role would only seem to become fully effective at sizes below 10 micron and would seem to require, as Mr. Viljoen has suggested, a mechanism for sizing which is effective down to, say, 1 micron. In the meantime it would be interesting to try tabling the flotation tailing to see if it was possible to recover the plus 20 micron cassiterite which is not recovered well by flotation. One point which has been made during discussion is the suggestion that cassiterite particles have a fully hydrated surface at normal pH. I wonder if this layer could materially affect the overall specific gravity of a very small cassiterite particle and, if so, whether gravity concentration of the very fine cassiterite would be improved if carried out in acid conditions, which would inhibit the formation of this hydrated surface. REFERENCES 1. CHASTON, I. R. M. 'Gravity concentration of fine cassiterite'. Trans. Inst. Min. and Met. Vol. 71, p. 4, 1961 and 1962, and discussion of this paper. Dr. R. P. King Mr Viljoen has drawn attention to the difficulties associated with the presence of very fine particles in the flotation pulp and he has indicated that, on the Union Tin plant, they must sacrifice 30 percent of the cassiterite in the minus 7 /Lm material which they separate and lose. He has also indicated that the rate of flotation of cassiterite remained high at these small sizes. The problem arises because the very small particles stabilize the froth making it impossible to handle. These stable froths cannot be easily broken and therefore cannot be pumped and processed. It seems that further fundamental research work on the properties of stabilized froths is urgently required. We have found another difficulty associated with the presence of very fine particles in phoscorite slurries; these particles can be easily floated but with very poor selectivity. We believe that it is possible that a purely physical mechanism such as entrainment is responsible for the collection of fine particles in the froth. We have also demonstrated that the presence of fine particles in the pulp adversely affects the rate of flotation of the larger particles. For esample, we have found an increase in recovery of + 100 um material from 2 percent to 17 percent in a standard laboratory batch flotation test on phoscorite when the - 37 um was removed from the feed. Such interactions between particles are not universally recognised as an important aspect of the complex flotation mechanism. They should appear in any quantitative formulation of the flotation rate process.

The June General Meeting of the Institute was held in Kelvin House, Johannesburg, on 18th June, 1969, at 4.30 p.m. Mr J. K. E. Douglas (Vice-President) was in the Chair. There were also present fourteen Members, Messrs R. J. Adamson, F. P. Bath, D. M. Jamieson, D. G. Maxwell, Dr J. T. McIntyre, and Mr P. W. J. van Rensburg (Council Members), Messrs B. F. Berry, A. F. Lee, J. E. van Leeuwen, G. G. Nicolson, N. F. Peverett, Dr A. G. Raper, Messrs E. R. Rudolph and H. R. Reid. Five Associate Members, Messrs T. D. Brown, M. R. Fuller-Good, J. S. Freer, Dr P. R. Jochens and Mr D. A. Viljoen. One Graduate, Mr P. G. Mrkusic. Five Students, Messrs N. A. Barcza, J. A. Cruise, R. P. W. Henrard, D. I. Ossin and J. C. M. Wethmar. Nine Visitors, Messrs M. Badenhorst, N. J. Bovey, H. H. Herold, Dr H. J. S. Kriek, Messrs M. S. Rennie, B. B. Segal, S. Selmer-Olsen, O. A. W. Strydom and B. Yates. Secretary, Mr D. C. Visser. Total present: Thirty-six. MINUTES The Vice-President: "May we confirm the minutes of the Monthly General Meetings held on 24th March, 16th April and 21st May, 1969 as published in the Journal?" Agreed. MEMBERSHIP The Vice-President: "I have much pleasure in announcing that the names of the undermentioned candidates having been published in accordance with By-Law 5.2.2, Council has elected them to membership of the Institute in the following grades: Members: Wilfred Desmond Morgan, Abraham Kriek. Associate Members: Rodger Neville Hampson, Robert Richard Booth Lodge. Graduates: Beverley Hugh Waiters, Gwynne Hugh Johnston. Students: Colin Edward Alvery, Peter Marthinus Haikes, Charles Aubrey Husband, John Nowell Randell, Frederick Johannes Jacobus Blaauw, Johannes Andries Breytenbach, Peter Vos, Frederik Hendrik Coetzee, Petrus Nicolaas Jacobus Smit, Patrick Alien Boardman, Robert Nelson Guest. "May I welcome the newly elected members to the Institute." (Applause.) ELECTION OF SCRUTINEERS FOR THE 1969-70 BALLOT FOR COUNCIL The Vice-President: "In terms of By-Law 9.4, I now call for nominations for scrutineers for the 1969-70 ballot for CounciL" P. W. J. van Rensborg: "I wish to nominate Messrs R. C. J. Goode, V. C. Robinson, J. K. E. Douglas, P. Lambooy, D. G. Maxwell, H. Britten and H. Simon as scrutineers."

Where is Your Advertisement

The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal. All papers must meet the standards set by the Council of the Institute, and for this purpose all papers are referred to at least two referees appointed by Council. STANDARDS FOR ACCEPTANCE To merit consideration papers should conform to the high standards which have been established for publication over many years. Papers on research should contain matter that is new, interpretations that are novel or of new significance and conclusions that cast a fresh light on old ideas. Descriptive papers should not be a repetition of well-known practices or ideas but should incorporate developments which would be of real interest to technical men and of benefit to the mining and metallurgical Industry. In some cases a well prepared review paper can be of value, and will be considered for publication. All papers and particularly research papers, no matter how technical the subject, should be written with the average reader of the Journal in mind, to ensure wide interest. The amount of textbook material included in a contribution should be the minimum essential to the argument. The length of a paper is not the criterion of its worth and it should be as brief and concise as possible, consistent with the lucid presentation of the subject. Only in very exceptional circumstances should a paper exceed 15 pages of the Journal (15 000 words, if there are no tables or diagrams). Six to ten pages is more normal. NOTE: Papers in the Journal are printed in 10 point type, which is larger than the 8 point type used on this page. For special publication Council may decide on page sizes smaller than A4 used for this Journal. The text should be typewritten, double-spaced, on one side only on A4 size paper, leaving a left-hand margin of 4 cm, and should be submitted in duplicate to facilitate the work of the referees and editors. Orthodox sequence Title and author's name, with author's degrees, titles, position. Synopsis. Index, only if paper is long and involved. Introduction, including a brief statement of conclusion. Development of the main substance. Conclusions, in more detail. Acknowledgements. References. Title: This should be as brief as possible, yet give a good idea of the subject and character of the paper. Style: Writing should conform to certain prescribed standards. The Institute is guided in its requirements by: Collins, F. H., Authors & Printers' Dictionary-Oxford University Press. Hart, H. Rules for Compositors and Readers. Humphrey Milford (familiarly known as the Oxford Rules). Fowler, H. W. & F. G. The King's English-Oxford University Press. General: A few well selected diagrams and illustrations are often more pertinent that an amorphous mass of text. Over-statement and dogmatism are jarring and have no place in technical writing. Avoid the use of the first person, be objective and do not include irrelevant or extraneous matter. Avoid unnecessary use of capitals and hyphens, while punctuation should be used sparingly and be governed by the needs of sense and diction. Sentences should be short, uninvolved and unambiguous. Paragraphs should also be short and serve to separate basic ideas into compact groups. Quotation marks should be of the 'single' type for quotations and "double" for quoted matter within quotations. Interpretations in the text should be marked off by parentheses ( ), whereas brackets [ ] are employed to enclose explanatory matter in the text. Words to be printed in italics should be underlined singly. For small capitals they are to be underlined DOUBLY and for large capitals TREBLY. Abbreviations and symbols are laid down in British Standard 1991. Abbreviations are the same for the singular and plural, e.g. cm for centimetre and centimetres, kg for kilogram and kilograms. Percentages are written in the text as per cent; the symbol % is restricted to tables. A full stop after an abbreviation is only used if there is likely to be confusion of meaning. Metric System: The Systemé International d'Unites (S.I.) is to be used for expressing quantities. This is a coherent system of metric units derived from six basic units (metre, kilogramme, second, ampere, kelvin, and candela), from which are derived all other units, e.g. the unit of force is the newton (N) for kilogramme metre per second per second (kg m/s2). Always use the standard metric abbreviations. Commas must not be used for separating groups of digits. For ease of reading digits should be grouped in threes counting from the decimal point towards the left and the right. Illustrations: Drawings and diagrams are to be in black India ink and should be about 18 cm wide. When submitting graphical representations avoid a fine grid if possible. Curves should be in heavy line to stand out. Lettering too should be bold as a reduction in size is often involved in the printing process. (A single column is 8.5 cm wide.) Numbering of tables should be in Roman numerals: I, 11, etc. and figures in Arabic numerals: Fig. 1, Fig. 2, etc. (Always use the abbreviation for figure.) Photographs should be black and white glossy prints. As a guide to the printer the author should indicate by means of notes in the typescript where tables and figures, etc. are to appear in the text. Paragraphs: A decimal system of numbering paragraphs may be used when the paper is long and complicated and there is a need for frequent reference to other parts of the paper. Proof correction: Galley proofs are sent to authors for the correction of printers' errors and not for the purpose of making alterations and additions which may be expensive. Should an author make alterations which are considered excessive, he may be required to pay for them. Standard symbols as laid down in British Standard 1219C should be used. SYNOPSIS It is most important that the synopsis should provide a clear outline of the contents of the paper, the results obtained and the author's conclusions. It should be written concisely and in normal rather than abbreviated English and should not exceed 250 words. While the emphasis is on brevity this should not be laboured to the extent of leaving out important matter or impairing intelligibility. Summaries simplify the task of abstractors and therefore should present a balanced and complete picture. It is preferable to use standard rather than proprietary terms. FOOTNOTES AND REFERENCES Footnotes should be used only when they are indispensable. In the typescript they should appear immediately below the line to which they refer and not at the foot of the page. References should be indicated by super-script, thus. . .1 . . .2. Do not use the word Bibliography. When authors cite publications of other societies or technical and trade journals, titles should be abbreviated in accordance with the standards adopted by this Journal. GENERAL The Council will consider the publication of technical notes taking up to three pages (maximum 3 000 words). Written contributions are invited to the discussion of all papers published in the Journal. The editors, however, are empowered by the Council to edit all contributions. Once a paper or a note has been submitted to the Institute, that document becomes the property of the Institute, which then holds the copyright when it is published. The Institute as a body is, however, not responsible for the statements made or opinions expressed in any of its publications. Reproduction from the Journal is permitted provided there is full acknowledgement of the source. These points should be borne in mind by authors who may submit their work to other organisations as well as to the Institute.

COUNCIL The following served on Council during the year under review: Office bearers: Messrs V. C. Robinson (President), Prof D. D. Howat and Dr J. P. Hugo (Vice-Presidents), J. K. E. Douglas (Immediate Past President) and D. G. Maxwell (Honorary Treasurer). Ordinary Members of Council: Dr M. G. Atmore, Dr J. M. Bereza, H. P. Carlisle, W. W. Malan, C. E. Mavrocordatos, Prof R. P. Plewman, Dr R. E. Robinson, Dr M. D. G. Salamon, P. W. J. van Rensburg, L. W. P. van den Bosch, P. A. von Wielligh. Branch Chairmen: J. Meintjes, J. M. Meyer (Acting), J. N. Saunders (Retired). Past Presidents serving on Council: R. J. Adamson, M. Barcza, H. Britten, R. C. J. Goode, P. Lambooy, Prof J. de V. Lambrechts, Dr J. T. Mclntyre, J. F. Reid, H. Simon. Ten Council meetings were held during the year with an average attendance of eighteen and the standing committees held forty-six meetings. FINANCE The annual accounts, which are attached to this report, show an excess of income over expenditure of R5 051 compared with an excess of expenditure over income last year of R4 608. This major reversal of fortunes is due in the first instance, of course, to the increased subscriptions. There were, however, other important contributors, particularly sales of the Proceedings of the Symposium on Open Pit Mining and profits on the operation of symposia and colloquia. It would appear from a study of the accounts that there has been a substantial drop in expenditure on secretarial fees. In actual fact, however, our total expenditure on secretarial fees was higher. A portion of this expenditure was charged against the administration of the Symposium on Open Pit Mining and, in addition, the charge against the Journal accounts for secretarial fees was increased. It will be recalled that in last year's annual report it was mentioned that subsequent to the new arrangement for publication of the Journal, the expected improvement in the finances of the Journal had been slow in materialising. After a total period of 18 months there was still no sign of improvement and it was accordingly decided to end the arrangement. As a result, the drain on the finances of the Institute was considerably lessened in the second half of the year. During the course of the year Council became concerned about the rapid depletion of our accumulated funds and gave careful and detailed attention to all aspects of the Institute's financial affairs. Particular attention was given to: 1. The fact that the Institute does not have a solid financial backing and must appeal for funds every time any special event such as a symposium is held. 2. The responsibilities of the Institute to the profession and the community, with particular reference to the desirability of establishing Institute bursaries and participating in other educational activities. 3. The rapidly rising cost of living. 4. The immediate financial position of the Institute. 5. The rapidly increasing cost of publishing the Journal due to the increasing number of papers available. In the meantime the immediate financial position of the Institute has improved but as this is due largely to non-recurring or irregular items of revenue, it should not be given undue weight. After careful consideration it was decided that an appeal should be made to industry for financial assistance, which would be used to cover the cost of symposia and other unusual expenditure and also, if possible, to build up the capital resources of the Institute so that there is a solid foundation for the future. Before appealing to industry, Council wished to be quite certain that there could be no criticism of the Institute for not having done our best in a personal capacity. Furthermore, Council examined many comparative statistics, including those circulated to members, which showed that, while expenditure per member has risen at an average annual rate of 7,5% over the last fifteen years, subscription revenue per member has risen at only 3,4% per annum. It was with this background that your Council decided to raise the subscriptions. Initial approaches have been made to the big mining groups and there has been a very generous response, although the details of how financial assistance will be provided have not yet been worked out. It seems likely that some form of affiliated company membership will be the most suitable method of achieving this. When these details have been fixed, it is the intention to extend the appeal to all corners of the mining industry as well as manufacturing and metallurgical industries. It is believed that these measures will ensure that the finances of the Institute are placed on a firm foundation on which the expanding activities can be planned. The MacArthur Forrest Memorial Fund shows an excess of income over expenditure of R73 and the total fund was, therefore, increased by this amount to R4 411. The balance sheet shows that the market value of quoted shares and debentures increased during the year fron R6 540 to R9 160. The market value is now almost exactly the same as the book value. Accumulated funds now amount to R23 010 compared with R17 959 a year ago.

ORANGE FREE STATE BRANCH Proceedings of the Annual General Meeting The Annual General Meeting of the Branch was held in the St. Helena Club on Tuesday, 3rd October, 1972 at 8.00 p.m. Mr J. M. Meyer was in the chair. METALLURGISTS AND COMPUTERS An address delivered at the Annual General Meeting of the O.F.S. Branch by Prof D. D. Howat. Most men who remain in mining and metallurgy like their jobs. There are many times when you say to yourself or to your wife - 'Anybody can have my job - if they want it'. You feel so fed up and frustrated everything that could go wrong has gone wrong.

By J. J. leR. Cilliers

ABSTRACT The recently introduced concept of negative taxation complicates estimation of the distributable profit of certain South African gold mines, and an assisted mine could operate at a working loss and yet produce an overall profit for distribution amongst its shareholders. A simple diagram is presented from which the approximate working profit or loss, taxation payable or tax credit received, and the distributable profit of an assisted mine can be estimated directly for any combination of the four main variable operational factors: tonnage milled, recovery grade, unit cost and capital expenditure. INTRODUCTION The effects on the working profits of South African Gold mines caused by changes in unit working costs, recovery grade, tonnage milled and capital expenditure are readily estimated. For normal tax- and lease-paying mines the distributable profit is related to the working profit and the latter is a commonly accepted comparative measure of the profitability of an operation. However, the recently introduced concept of State assistance in the form of negative taxation1, i.e. a tax credit, for mines with a life of less than eight years complicates such estimates. A requirement of State assistance is that an assisted mine must lower its normal pay limit by 16 to 20 per cent, and it will be possible for a mine to operate at a working loss and yet produce an overall profit for distribution amongst its shareholders. In the case of an assisted mine it is therefore necessary for management to judge the effects of changes in unit costs, grade, etc., in terms of distributable profit instead of working profit. This will require repeated calculation of tax to be paid or tax credits that will be received under the numerous possible combinations of the four main variable factors. However, with the aid of the diagram illustrated in Fig. 1, it is possible to assess at a glance the practical effect of these variables on the distributable profit of an operation not subject to tax on the normal formula, or small mine formula, with sufficient accuracy to decide whether a detailed analysis is required. USE OF THE DIAGRAM From the central point 'X' in Fig. 1, a range of tonnages milled per annum has been plotted along the north-bearing axis, a series of costs per ton milled in the northwestern quadrant, recovery grades in the northeastern quadrant, and capital expenditures in the southwestern quadrant. Starting from the tonnage milled per annum, a line is drawn east and west across the two northern quadrants up to the points where it reaches the desired cost- and grade-lines. From these points two north-south lines are drawn into the southern quadrants. A further line is drawn to the east from the point where the western north-south line crosses the desired capital expenditure. Distributable profit is read off in the southeastern quadrant where this line intersects the eastern north-south line. Every possible combination of

The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal. STANDARDS FOR ACCEPTANCE To merit consideration papers should be of sufficient high standard and contain matter that is new, interpretations that are novel or of new significance and conclusions that cast a fresh light on old ideas. Their publication should be of real interest to technical men and of benefit to mining and industry. Authors must realize that because a mine shaft is new or the mine itself is newly established, this in itself does not justify a paper unless significantly new techniques or processes were involved in the opening-up procedure. A few well selected diagrams and illustrations are often more pertinent than an amorphous mass of less well chosen material. Over-statement and dogmatism are jarring and have no place in technical writing. The amount of textbook material included in a contribution should be the minimum essential to the argument. The length of a paper is not the criterion of its worth and it should be as brief and concise as possible, consistent with the lucid presentation of the subject. Avoid the use of the first person, be objective and do not include irrelevant or extraneous matter. Papers should be submitted at least three months prior to the intended date of presentation. The text should be typewritten, double-spaced, on one side only of foolscap paper, leaving a left-hand margin of 11-inches, and should be submitted in duplicate to facilitate the work of the referees and editors. Galley proofs are sent to the authors for the correction of printers' errors and not for the purpose of making alterations and additions which may be expensive. Should an author make alterations which are considered excessive, he may be required to pay for them. ORTHODOX SEQUENCE Title and author's name together with author's degrees, titles and position Summary, abstract or synopsis Introduction Development of the main substance Conclusions References. Title: This should be as brief as possible, yet give a good idea of the subject and character of the paper. Style: Writing should conform to certain prescribed standards. The Institute is guided in its requirements by: Collins, F. H. Authors' & Printers' Dictionary-Oxford University Press. Hart, H. Rulesfor Compositors and Readers. Humphrey Milford (familiarily known as the Oxford Rules). Fowler, H. W. & F. G. The King's English-Oxford University Press. Generally: Avoid unnecessary use of capitals and hyphens, while punctuation should be used sparingly and be governed by the needs of sense and diction. Sentences should be short, uninvolved and unamiguous. Paragraphs should also be short and serve to separate basic ideas into compact groups. Quotation marks should be of the 'single' type for quotations and "double" for quoted matter within quotations. Interpretations in the text should be marked off by parenthesis ( ), whereas brackets [ ] are employed to enclose explanatory matter in the text. Words to be printed in italics should be underlined singly. For small capitals they are to be underlined DOUBLY and for large capitals TREBLY. Abbreviations and symbols are laid down in British Standard 1991 and proof correction symbols in British Standard 1219C. Abbreviations are the same for the singular and plural, e.g. ft for foot and feet, lb for pound and pounds. Percentages are written in the text as per cent; the symbol % is restricted to tables. Likewise ft and in. should be used, x' y" only being permissible in diagrams and plans. Drawings and diagrams are to be in black India ink and should be about 6 in. wide. Numbering of tables should be in Roman numerals: I, II, etc. and figures in Arabic numerals: Fig. 1, Fig. 2, etc. Photographs should be black and white glossy prints. As a guide to the printer the author should indicate by means of notes in the margin of the typescript where drawings and diagrams, etc. are to appear in the text. When submitting graphical representations avoid a fine grid if possible. Curves should be in heavy line to stand out. Lettering too should be bold as a reduction in size is often involved in the printing process. SUMMARY ABSTRACT OR SYNOPSIS It is most important that the summary should provide a clear outline of the contents of the paper, the results obtained and the author's conclusions. It should be written concisely and in normal rather than abbreviated English and should not exceed 250 words. While the emphasis is on brevity this should not be laboured to the extent of leaving out important matter or impairing intelligibility. Summaries simplify the task of abstractors and therefore should present a balanced and complete picture. It is preferable to use standard rather than proprietary terms. FOOTNOTESAND REFERENCES Footnotes should be resorted to only when they are indispensable. In the typescript they should appear immediately below the line to which they refer and not at the foot of the page. References should be indicated by super-script, thus . . .1 . . . 2. Do not use the word Bibliography. When authors cite publications of other societies or technical and trade journals, titles should be abbreviated in accordance with the standards adopted by this Journal.

The Institute was founded in 1894 as the Chemical and Metallurgical Society of South Africa. In 1904 it was reconstituted as the Chemical Metallurgical and Mining Society of South Africa and in 1956 it became the South African Institute of Mining and Metallurgy. The objects of the Institute are to advance the science and practice of mining and metallurgy, to afford opportunities for the interchange and recording of knowledge of mining and metallurgy and to ensure high standards of professional conduct and competence. Membership benefits include monthly issues of the Journal of the Institute, General Meetings at which papers are read, symposia, excursions to mining and industrial concerns and the use of club facilities at Kelvin House. Technical journals received on an exchange basis are available to members at the Johannesburg Public Library. The current membership of the Institute is over 1 600. Membership applications are accepted from suitably qualified persons and the requirements for entrance to the various grades of membership are summarised below. Fellows shall not be less than 30 years of age, shall be university graduates in pure or applied science or shall produce evidence to the satisfaction of the Council that they have successfully completed a co-ordinated course of study in pure or applied science of at least three years' duration at an approved university or institution deemed by the Council to be of equivalent status. Members shall have been employed in senior technical positions in important mining or metallurgical undertakings for at least five years or they shall have practised as mining or metallurgical consultants for at least five years. They shall be practising their profession at the time of application. Entrance fee R10,00, Annual subscription R20,00. Letters of designation: F.S.A.I.M.M. Members shall be not less than 25 years of age and shall be university graduates in pure or applied science, or shall have successfully completed co-ordinated courses of study in pure or applied science of at least three years' duration. They shall have been engaged in work of an approved technical character in the mining or metallurgical industries, of which not less than two years shall have been in positions of responsibility. A candidate shall be practising his profession at the time of his application. Entrance fee R8,00, Annual subscription R18,00. Letters of designation: M.S.A.I.M.M. Associates shall be not less than twenty-five years of age, and shall have been engaged in positions of responsibility in, or associated with, the mining or metallurgical industries for periods of not less than three years. If, however, the candidate for admission to the higher grade of Associate, is at the time of his application, already a Student, he need satisfy the Council only that he is, at the time of his application, engaged in a position of responsibility in or associated with the mining or metallurgical industries. In all cases the applicants shall satisfy the Council that they are fit and proper persons to become Associates. Entrance fee R8,00, Annual subscription R18,00. Graduates shall be not less than 21 years of age and shall be university graduates in pure or applied science, or have completed co-ordinated courses of study in pure or applied science of at least three years' duration at an approved university or institution. They shall not remain Graduate members after attaining the age of 30 years without the permission of Council. Entrance fee R2,00, Annual subscription R12,00. Students shall be persons not less than 18 years of age who are being educated or trained in a manner approved by the Councils to occupy a technical position in or associated with the mining or metallurgical industries and who, furthermore, shall not have attained the qualification required for a higher grade of membership. They may remain Students until they have obtained the necessary qualifications for transfer to a higher grade of membership, but not after the end of the Institute's financial year in which they attain the age of 28 (twenty-eight) years. They shall then transfer to a higher grade to retain membership of the Institute. The Council may relax the provisions of this clause in such cases as it considers appropriate. Entrance fee nil; Annual subscription R5,00. Other. The Council has the power to elect to the grade of Fellow or Member, candidates who may not fulfil all the requirements for entrance to these grades but whose status, professional achievements and practical experience in mining or metallurgy justify such election. Applications. Requests for membership application form should be addressed on the attached form to the Secretaries South African Institute of Mining and Metallurgy, P.O. Box 61019, Marshalltown, Transvaal.

By H. J. E. Hamel

Some aspects of the deformation behaviour and temperature rise during instantaneous compression loading of high purity aluminium By H. J. E. HAMEL The influence of deformation speed on the deformation behaviour of high purity aluminium was investigated. By varying the initial height-to-diameter ratio a considerable influence on the deformation behaviour could be noticed. Lubrication of the specimen end faces was found to have an influence on the flow behaviour and on the roughness of the specimen interface at pressing platens. The results of temperature measurements during deformation agree with work-hardening behaviour of the specimens. Flow curves calculated with the measured temperature rises do not agree with results obtained at lower strains by other workers. The possible reasons are discussed.

By D. J. Bosman

Rapid fouling of condenser tubes in underground refrigeration plants is a frequent occurrence. It leads to low heat transfer efficiencies, with consequent serious reduction in capacity and increase in the horse-power requirement of the units. High pressures develop in the condensers, and frequent cleaning of the tube bundles is required. The cleaning operation takes up to 8 hours and in some cases results in significant loss of production. One of the possible causes of fouling is deposition of scale, but this can be readily overcome by controlling the concentration of the water. When water evaporates, the dissolved solids remain behind; thus evaporation increases the amount of dissolved solids per unit volume. If half the original volume evaporates, the concentration of the dissolved solids is doubled and the water is said to have a 'concentration' of two. Concentration may be controlled by regulating the amount of water allowed to bleed from the system. The actual concentration value required is a function of the chemical analysis of the circulating cooling water. In one instance, where the problem of scale formation had been eliminated, fouling still persisted, and the possibility of excessive quantities of dust in the re-circulating water was investigated. A dispersing reagent was added to the condenser cooling water as a means of preventing sludge deposition in the condenser tubes. As shown by curve A in Fig. 1 the reagent addition did not decrease the rate of fouling.

By M. H. Kirchner

Trackless mining at Thabazimbi Mine by M. H. KIRCHNER. Pr. Eng.. B.Sc.. B.Sc. (Elec. Eng.)(Stellenbosch). Dip. Mining (Pta.) Certain aspects of the' methods used in the exploitation, by sub-level caving, of a wide, tabular, steeply dipping orebody are described, reference being made to the use of modern mechanized equipment. Statistics relating to production and labour, as well as some geological details, are given.

By W. K. C. Boemer, G. A. Davies

Vanadium slag production in the shaking ladles started in April 1968, steelmaking was begun in July 1968 and the first continuously cast blocks were produced soon after on the 29th July, 1968. Nominal monthly production of over 20 000 tons was reached in seven months and by December 1970 about 12 000 heats were cast and a monthly production of 35000 tons has been achieved.

By A. C. Lawrence

A new approach to the -study of human factors in stope productivity by A. C. LAWRENCE B. Econ., D. Com. (S.A.) (Member) The extent of the improvement in mean performance which could be achieved by reducing the variance between stoping gangs is examined, and it is shown that a worthwhile gain would result if variance were reduced by as little as 5 to 15 per cent. The problem of identifying human factors which contributed towards variance in gang performance was examined in one gold mine. A total of 342 'observations' on 49 stoping gangs were gathered, each observation consisting of a set of figures for 36 variables for one gang for one week. The variables included 'stope factors' such as face length, 'gang factors' such as the ethnic composition of the gang, and 'supervisory factors' such as the experience of the miner. These variables were related to 'tons trammed per week' as a measure of work performance. The findings showed that certain of the predictor variables accounted for 66 per cent of the variance in gang performance and about two thirds of this could be attributed to gang and supervisory factors, that is to the 'human factors'. The method suggests a basis for a new approach to the identification of human factors and is a promising step towards optimizing gang performance.

By E. Pothas, P. R. Jochens, L. B. McRae, D. D. Howat

SYNOPSIS The phase equilibria, viscosities and sulphur capacities of titaniferous slags were determined in the composition range of CaO = 30 to 0 per cent, MgO = 0 to 30 per cent, SiO2 = 19.69 per cent, AI.O. = 13.12 per cent and TiO2 = 37.19 per cent. The phase equilibria were determined by high temperature microscopy, the viscosities were measured using a rotating outer cylinder viscometer and the sulphur capacities were evaluated from the results obtained by equilibrating the slag in a gas stream of CO, CO2 and SO2. The behaviour of these titaniferous slags under reducing conditions was examined. Possible use of the slags for aggregate, or slag-cement, and the possibility of extracting the TiO2 are discussed. CONTENTS INTRODUCTION PHASE EQUILIBRIA VISCOSITIES DISCUSSION OF THE PHASE EQUILlBRIA AND THE VISCOSITY VALUES EFFECT OF REDUCING CONDITIONS SULPHUR CAPACITY DISCUSSION OF THE SULPHUR CAPACITY VALUES POSSIBLE USES CONCLUSIONS ACKNOWLEDGEMENTS REFERENCES INTRODUCTION The latest phase in the exploitation of the mineral wealth of the Bushveld Igneous Complex is the erection of a plant by the Highveld Steel and Vanadium Corporation Limited near Witbank to produce steel and vanadium-rich slag from the titaniferous magnetites occurring in this rock formation. These titaniferous magnetites occur as segregations in the gabbro body and the TiO2 is mainly present within the structure of other constituent minerals but also occurs in smaller amounts as ilmenite and ulvospinel. The vanadium is thought to be present in the iron oxide phase due to isomorphous replacement of the iron. Until very recently, it was feared that the high titania content of these titaniferous magnetites would militate against their value as useful iron ores. However, the design of an integrated plant to produce both steel and vanadium-rich slag, and in which the iron-making process is conducted in submerged arc furnaces instead of in

The May General Meeting of the Institute was held in Kelvin House, Johannesburg on 20th May, at 4.30 p.m. Mr V. C. Robinson (Vice-President) was in the Chair in the absence, overseas, of the President, Mr J. K. E. Douglas. There were also present 16 Fellows: Messrs J. A. Adamson, R. S. J. du Toit, J. A. Drummond, D. F. A. Grave, T. L. Gibbs, G. H. Grange, D. V. Howat, P. H. Kitto, Dr P. J. LIoyd, Messrs B. H. L. Leach, J. de V. Lambrechts, Dr J. T. McIntyre, Messrs C. S. MacPhail, P. W. van Rensburg, S. G. Taussig, W. S. Rapson. Six Members: Messrs E. L. Atkinson, R. Hemp, Dr J. Martinson, Messrs A. H. Munro, G. J. van Jaarsveld and J. H. Qwilliam. Two Associate Members: Messrs B. H. van Rensburg and H. Triiter. Four Visitors: Prof J. E. Kerrich, Dr G. K. Sluis-Cremer, Messrs D. Kisbey-Green and L. W. Isserow. For Secretariat: Mrs S. de Gersigny. Total present: 27. OBITUARY The Vice-President: "It is my sad duty to announce the death of Stephen Ring, a member who joined the Institute in ]961, and passed away on the 31st of December, 1969. I would ask you all to rise and observe a moment's silence. Thank you." MINUTES The Vice-President: "May we confirm the minutes of the Special General Meeting and Monthly General Meeting, held on 20th February, 1970, as published in the April issue of the Journal?" MEMBERSHIP The Vice-President: "I have much pleasure in announcing that the names of the undermentioned candidates, having been published in accordance with By-Law 5 2.2, Council has elected them to membership of the Institute in the following grades: Fellows: Denis Ian Field, Arthur Cecil Waiter Comyn, John Hall, Leon VercueiI. Members: Jan McLellan Vosloo, Jan van Velze. Graduates: Richard Darnley Beck, John Edward Andrews, Roderick Nowell Randell. Associates: Alexander Duncan Ross, Ian James Terrill. Students: Hendrik Jacobus Oostenwald Prins Smith, Graham Peter Gooding, Rudannes Raath Homan. "I welcome the newly, elected members to the Institute." GENERAL BUSINESS The Vice-President: "Are there any matters which you wish to raise under 'General'? There being no matters to raise under 'General', we will proceed to the next item on the Agenda." PAPER FOR PRESENTATION The Vice-President: "It is my pleasant duty to call on Dr du Toit to deliver his paper, entitled, 'The functional relationship between dust hazard and the rate of collecting funds to pay compensation for pneumoconiosis'." After the presentation of the paper (published in the March Journal) the Vice-President said: "This paper is a very important addition to the considerable volume of work applications on this subject of pneumoconiosis. The disease, in all its various forms, has received attention from many, many great men, both in the medical world, and engineers. The fact that there is this big volume of publications of literature on it still doesn't mean that we can get anywhere beyond the old, simple injunction, that the prevention of pneumoconiosis does not depend on compensation, levies or anything else. It simply depends on allaying dust as quickly as possible. "This paper, however, is another scientific landmark and I think, in a cold and dispassionate way, it sets out some important points in this whole subject of the relationship of the levy - the money of compensation to the dust which causes it. "I have, personally, very little to criticise in this paper but when I listened to Dr du Toit's final conclusions, I wondered whether the words, 'Within the data available', aren't the key to this whole situation. I agree that he has demonstrated a workable relationship between the current industries for levy and dustiness, but among the factors which he lists as being important, I know that there is one which is missing. This is extremely difficult to evaluate. It's a factor which has destroyed, on so many occasions, the work which has been done by so many genuine, intent, honest people working in this field, and this is this unknown factor, this hidden factor of political opportunism, which has so often played a very important part in pneumoconiosis compensation. "How many of us have seen the grubby, grasping fingers of power-mad demagogues, and I can name them for you - but I won't - and also the blatant vote-catching of certain politicians interfering in this field. How, at the end of all that, the poor scientist, the poor dedicated man in the Mines' Department, who has to write the law of compensation, can operate, I do not know. "From this picture the ordinary layman recoils in horror. Among the casualties in this particular war, which has been fought over so many years, I am perfectly certain, are some of the criteria of certification, especially in '56/,57, when that extraordinary condition, known as 'pulmonary disability' was introduced. I am sure there were casualties then, in the criteria of certification. "Nevertheless, this paper is a worthy addition to the long list of scientific work done on this so-important

A. H. Mokken: I am pleased to have been given this opportunity to make a contribution to Dr Muller's paper tonight. The reason for this is that, at one stage in our careers, we were associates in the same undertaking. Dr Muller, then fresh from University, with a degree in pure science, had just stepped onto the first rung of the ladder, which, it was then thought, would lead him to a career in gold extractive metallurgy. However, endowed with an enquiring mind and conscious of a lack of fundamental training in general metallurgy and engineering, he felt a need for further academic study. To meet this need and, more importantly, to meet the necessary finances, he found his opportunity in steel. Armed with a bursary, he bade farewell to gold and proceeded overseas, to the University of Sheffield, to train as a steel metallurgist. The outcome of these academic efforts, which were followed by assignments in the steel industry and a further period at Sheffield, is the man we have listened to tonight-a highly qualified metallurgist who has displayed a sound knowledge of his subject. In choosing Sheffield, Dr Muller became associated with a steelmaking centre of world renown, a centre usually credited with the first systematic production of alloy steels, as far back as the 18th century. Since that time, great advances have been made in the production of alloy steels and this is especially so in the last decade or two, when major developments in civil, mechanical, electrical, aeronautical and nuclear engineering have been made possible by the development of steels with improved properties. In spite of spectacular advances in the technology of non-ferrous alloys, plastics and other materials of construction, steel has maintained its role as a pre-eminent material for engineering use. With the gradual accumulation of data on the properties of steels, and the use of thin film electron microscopy, to study the behaviour and characteristics of such phenomena as dislocations in metals and other microstructural features, the physical metallurgist appears to be approaching the stage of an exact understanding of such phenomena as strength, ductility and brittleness-a knowledge which could lead to close control of such properties and, therefore, to the attainment of the highest goals. An interesting example, illustrating the use of fundamental principles, based on physico-metallurgical research, is the development of the maraging steels developed by Bieber at the International Nickel Company. These steels have met the extreme technological requirements of the space age by providing the material for the cases of large rockets in which qualities, such as high tensile strength, toughness, workability and weldability are most important. Attractive as they might appear to be in considerations of savings of weight, cost of erection, transport of materials and foundations, the use of high strength steels has been accompanied by special problems such as brittle fracture, hydrogen embrittlement, notch-toughness and fatigue. It has been found that high strength steels, which performed acceptably in conventional tension tests, were found to undergo failure, in a brittle manner, in service. Hydrogen embrittlement has caused spectacular failures at a fraction of the normal ultimate tensile strength, and a lack of correlation between fatigue and tensile strengths has diminished the advantages to be obtained from the use of high strength steel in some applications. A new approach to the selection of materials for engineering design has resulted from a consideration of these phenomena in which strength, as such, is no longer as significant as it was previously. Parallel with the development of high strength steel has been the need for suitable techniques for joining component parts and here welding has played an