Search Documents

By R. M. Williams

Introduction Ring roller mills are efficient size reduction machines embodying the following machine functions: 1) Size Reduction: from a feed size of 2 in. to various size products as fine as 400 mesh, or granulation from 2 in. to 6 mesh containing a minimum of fines. 2) Drying: fluid bed drying of wet feed materials. 3) Conveying: negative pressure air system results in dust-free conveying. 4) Beneficiation: liberation and removal of foreign materials from the auxiliary bottom discharge simultaneously while grinding. Operation Operation of the roller mill system, Figs. 78 and 79, is completely automatic. A feeder introduces raw material into the grinding chamber in the base of the roller mill at a rate determined by pressure variations within the roller mill as material is ground and air conveyed away. The feeder will be activated by the reduced static pressure and introduce unground material into the system, thereby maintaining a constant differential pressure. Plows located ahead of each grinding roll direct the material upward and between the grinding rolls and the bull ring where it is ground to size. The grinding rolls are free to swing out centrifugally, which forces them to bear upon and grind the raw material. Being free to pivot axially, the rolls automatically assume the proper position for grinding and need no adjustment to compensate for wear. Rotation of the rolls is by rolling contact. Once ground to size, material is swept out of the mill by the controlled air flow from the centrifugal main mill fan. Air suspended, the ground material passing through the adjustable spinner separator. In the separator, an accurate size classification is made which allows product-size material to be conveyed away from the roller mill while oversize material is returned internally for additional grinding. By varying the speed of the separator drive, more or less cyclonic action is achieved at this location, effectively controlling product size. Product sized material is removed from the airstream by the cyclone collector. Typically, a conveyor or product storage bin will be located to accept the product as it exits from the bottom of the cyclone collector.

Jan 1, 1985

By Wolfgang Pietsch

Roller presses were first invented in the middle of the 19th century, for the economical size enlargement of coal fines as fuels. Coal briquettes became quickly accepted for industrial and domestic use giving rise to a large and sucessful industry, particularly in Europe, Japan, and North America. When, towards the middle of the 20th century, coal was more and more replaced by other energy sources, such as electricity, gas, and oil, roller press manufacturers searched for alternate applications of this equipment. In addition to contemporary coal briquetting, in fields such as smokeless fuel and form-coke, it was found that redesigned and modernized roller presses, which are now capable of exerting high forces, are versatile machines for many tasks in mineral processing. Today they are used for: - the "classic" pressure agglomeration and - the "new" high pressure comminution. In pressure agglomeration, the characteristics of fine minerals are improved by forming briquettes or granulated products from compacts. During size enlargement with roller presses briquettes are directly obtained while granular materials are produced by crushing and sizing of compacted sheets. The processes are carried-out essentially dry and often do not require binders other than those inherently contained in the feed and "activated" by the high forces and/or elevated feed temperatures (e.g. hot briquetting). Therefore, no foreign materials (impurities) are added. Another advantage of the technology is, that wide particle size distributions are acceptable or desirable as feed materials, including millimeter or even centimeter sized particles. Plastic particles deform and brittle materials are crushed during pressure agglomeration. A relatively new application of roller presses in mineral processing is the utilization of the crushing effect when brittle materials pass the nip area between the rollers. It was found that this crushing mechanism is very efficient thus saving energy, particularly in grinding circuits handling large capacities. The paper introduces the fundamentals of the process and describes the design as well as applications of modern roller presses in mineral processing.

Jan 1, 1995

By R. S. Shepard

A quick glance at a-portion of the title of this discussion -'Rolling With The Punch" may immediately lead you to assume that I am about to expound on the so-called manly art of self-defense. So that you will not have been misled entirely we will devote our considerations to a far more important art and if I may, I should like to begin by quoting Vincent Van Gogh. According to a literal translation the artist in describing one of his famous paintings said "these peasants are eating their potatoes with those very hands that dug them from the earth' and put them in the dish". Vincent Van Gogh may not have realized at that time, that he could likewise have been describing what is probably one of the oldest of all arts - the art of Material Handling - an art that man with the aid of science has tried to improve since the beginning of time.

Jan 1, 1963

By Robert Stefanko

13.1-SUBSIDENCE AND GROUND MOVEMENT ROBERT STEFANKO 13.1.1-SUBSIDENCE AND FAILURE This treatment of subsidence and ground movement will be confined to subsidence control for limiting surface damage by assessing the significant parameters affecting ground movements during mining to optimize mining techniques. The material will be equally applicable to evaporite mining as well as coal but will not deal with block caving or similar systems where failure is deliberately induced and surface protection is not necessary or provided. When an underground opening is established, the original equilibrium is disturbed with resultant stress concentrations. While many factors are involved in opening stability, the span (W) undoubtedly is one of the most important factors in failure. Assuming it is relatively small, the overlying rock strata can bridge across the opening and little if any movement or convergence of top and bottom will occur. However, as the span increases, a point is reached where the stress in the overlying rock strata exceeds some strength value of the rock, and the top breaks. If the opening span is limited to some subcritical value (-We) and/or is at great depth (D), a pseudo-arch will form, achielring stability before rupture occurs to the surface. The boundary of this arch is thought to approximate an ellipse in form with the major axis vertical and equal to four times W, although there has been little field research to substantiate this theory. However, if the width of this opening is increased at this horizon to some critical value (W,) or the same span is created in a shallower seam, the overlying strata ill progressively rupture to the surface and the characteristic subsidence trough is formed (Fig. 13-1) The area of the surface affected is much greater than the area of the seam extracted, depending on the "angle of draw" (a), which is the angle between a vertical line from the edge of the opening and another line extended to a point at which subsidence tails out to zero. This angle has been found to be about 35° in Europe but is rather academic, being a function of instrument precision in detecting subsidence. Since the subsidence effect is so small at any point beyond n 25° angle, this latter may be considered the practical limit of subsidence. Further- more, indications are that the angle of draw varies with depth and nature of the strata.' In a field study over a 1,000-ft-deep potash mine in New Mexico, the maximum angle of draw was found to be 51.5°.2 So far, only a single opening has been considered. However, the width of the excavation applies to any complex mining system of entries, rooms and longwalls as long as the seam has been fully extracted and the width represents the distance from one solid rib to another. It will be noted that the amount of vertical displacement varies from point to point on the surface (s), but the maximum subsidence for a given trough occurs at the center (S). This latter value may not he equal to the maximum possible subsidence (Sm) which occurs only if a critical or super- critical (+W,) width has been exceeded (Fig. 13-1). Substantial surface damage can result when subsidence occurs. Factors affecting the amount and type of ground movement are: thickness and properties of the seam, angle of draw, width of excavation, depth and type of overburden, inclinations of strata and surface, and the amount of support left in the gob. In Europe,

Jan 1, 1973

By J. L. Ellenberger, T. Miller

"A limestone mine in Ohio has had roof instability problems that have led to massive roof falls extending to the surface. This paper describes a collaborative study of these events undertaken by the National Institute for Occupational Safety and Health and the mine owners. The study focuses on the roles that weak, moisture-sensitive floor and weak bands in pillars play in a general instability that led to roof falls at this mine. The NIOSH Stone Mine Pillar Design software (S-Pillar) does not include analysis for weak floor or weak bands and recommends that when such issues arise they should be investigated further using a more advanced analysis. It is important to recognize that without the impact of the floor or weak bands, the calculated inherent stability factor for these pillars is within the recommended design range. Therefore, to further investigate the observed instability occurring on a large scale at the Ohio mine, FLAC3D numerical models were employed to help determine the failure mechanism. Roof-to-floor extensometers were also installed in the areas predicted to have further instability. This case study will provide important information to limestone mine operators regarding the impact of weak floor causing the potential for roof collapse, pillar failure, and subsequent subsidence of the ground surface. This recent case demonstrates that weak floor can be a significant factor in pillar stability and should be assessed during the design stage of the mine.To an area-wide failure (Zipf, 2001). In that case, it appears that the pillars had actually remained intact. However, moisture-related yield of the weak floor caused deformations which passed through pillars and into the roof, triggering roof collapse around the intact pillars (Esterhuizen et al., 2011). This previous case and the case presented in this study, while not identical, both demonstrate that weak floor and/or bands within pillars can be a significant factor leading to instability."

Jan 1, 2015

By J. L. Ellenberger, G. S. Esterhuizen, T. Miller, M. M. Murphy

A limestone mine in Ohio has had roof instability problems that have led to massive roof falls extending to the surface. This paper describes a collaborative study of these events undertaken by the National Institute for Occupational Safety and Health and the mine owners. The study focuses on the roles that weak, moisture-sensitive floor and weak bands in pillars play in a general instability that led to roof falls at this mine. The NIOSH Stone Mine Pillar Design software (S-Pillar) does not include analysis for weak floor or weak bands and recommends that when such issues arise they should be investigated further using a more advanced analysis. It is important to recognize that without the impact of the floor or weak bands, the calculated inherent stability factor for these pillars is within the recommended design range. Therefore, to further investigate the observed instability occurring on a large scale at the Ohio mine, FLAC3D numerical models were employed to help determine the failure mechanism. Roof-to-floor convergence monitors were also installed in the areas predicted to have further instability. This case study will provide important information to limestone mine operators regarding the impact of weak floor causing the potential for roof collapse, pillar failure, and subsequent subsidence of the ground surface. This recent case demonstrates that weak floor can be a significant factor in pillar stability and should be assessed during the design stage of the mine.

Jan 1, 2015

By C. Mark, D. M. Pappas

From 1999 through 2008, groundfall events resulted in 75 fatalities, 5,941 injuries and 13,774 noninjury roof falls in U.S. underground coal mines, according to the U.S. Mine Safety and Health Administration (MSHA). A comprehensive analysis of these events was conducted to better understand where and why these incidents occurred. The first segment of the study used the MSHA database to evaluate groundfall injury rate trends related to mining method, year, locality, seam thickness, mine size, coalbeds and seasonal effects. In the past decade, roof fall injury rates have dropped 50%, but rib fall injury rates have remained constant. Room-and-pillar mines had a roof fall injury rate that was nearly 2.5 times the longwall rate. High groundfall rates occurred in the Illinois Basin, a finding that correlates with other studies that have shown that roof rock in the Illinois Basin is weaker than that in the central Appalachian coalfields. Finally, noninjury roof fall rates in the eastern and central United States were found to be 50% higher from July through September, possibly because of the changes in humidity levels that may cause shale mine roofs to deteriorate. The second segment of the study evaluated the root causes of failure by reviewing all MSHA groundfall fatality reports for 1999-2008. Pillar recovery was the leading cause of groundfall fatalities (19%), followed by rib falls, roof skin falls and traveling under unsupported roof (16% each). Defining prominent ground control incident trends and hazards will identify areas where additional study is needed and where innovative solutions need to be developed to reduce these severe occupational hazards.

Jan 1, 2011

By A. T. Iannacchione

Unfortunately from 1991 through 1995, 44 miners were fatally injured in the stone industry. Of these 12 occurred at underground mines from a total work force of less than 2,000 miners. Nine of these 12 miners were fatally injured in falls of roof or rib. A safer environment for the miners can be achieved by evaluating the nature of the hazardous ground and by developing more efficient and effective ground control strategies. Roof and rib conditions in the underground stone industry were observed and assessed at 33 mines in Illinois, Indiana, Kentucky, Maryland, Missouri, Pennsylvania, and West Virginia (Figure 1). Hazard assessment indicated that those ground failures occurring under moderate to substantial overburden ( > 30 m [100 ft]) were caused by stress concentrations and geologic structures. Ground failures near the surface are caused by solution (water) processes. Selection of the mining horizon and mine layout decisions tremendously influence ground stability.

Jan 1, 1997

By L. J. Prosser, A. T. Iannacchione

From 1991 through 1995, 44 miners out of a total workforce of less than 2,000 were fatally injured in the stone industry. Of these, 12 occurred at underground mining operations with nine deaths resulting from roof or rib falls. A safer environment can be achieved by evaluating the nature of the hazardous ground and by developing more efficient and effective ground-control strategies. Roof and rib conditions were observed and assessed in 33 underground stone mines in Illinois, Indiana, Kentucky, Maryland, Missouri, Pennsylvania and West Virginia (Fig. 1). Hazard assessment indicated that the ground failures that occurred under moderate to substantial overburden, i.e., >30 m (100 ft), were caused by stress concentrations and geologic structures. Ground failures near the surface are caused by solution (water) processes. Selection of the mining horizon and mine-layout decisions

Jan 1, 1999

By L. J. Prosser, A. T. Iannacchione

Unfortunately from 1991 through 1995, 44 miners were fatally injured in the stone industry. Of these 12 occurred at underground mines from a total work force of less than 2,000 miners. Nine of these 12 miners were fatally injured in falls of roof or rib. A safer environment for the miners can be achieved by evaluating the nature of the hazardous ground and by developing more efficient and effective ground control strategies. Roof and rib conditions in the underground stone industry were observed and assessed at 33 mines in Illinois, Indiana, Kentucky, Maryland, Missouri, Pennsylvania, and West Virginia [(Figure 1)]. Hazard assessment indicated that those ground failures occurring under moderate to substantial overburden (> 30 m [l00 ft]) were caused by stress concentrations and geologic structures. Ground failures near the surface are caused by solution (water) processes. Selection of the mining horizon and mine layout decisions tremendously influence ground stability.

Feb 24, 1997

By E. M. Frizzell

An ongoing research program at the Spokane Research Center of the U.S. Bureau of Mines is directed toward investigating drilling parameters (thrust, torque, penetration rate, and drill revolutions) during the drilling of roof bolt holes. A system that measures these drilling parameters calculates the specific energy of drilling, and determines drill bit position has been developed by the Bureau and mounted on a roof bolting/drilling machine, through the use of a microcomputer, critical drilling parameters can be immediately interpreted and analyzed. This makes it possible to inform the operator of hazardous roof conditions. Initial results of this program are presented here.

Jan 1, 1990

By M. R. Shahan, W. R. Reed, P. Zhang, J. P. Rider

Roof bolter operators may be exposed to high respirable dust concentrations on continuous miner sections with blowing face ventilation when bolting is performed downwind of the continuous miner. One solution to reduce the high respirable dust concentrations is to use a canopy air curtain (CAC) to deliver clean air from a filtered blower fan directly to the bolter operators under the canopies. The influence of CAC installation in the airflow and dust dispersion around the location of the roof bolter operator can be evaluated by using computational fluid dynamics (CFD). This study, performed by the National Institute for Occupational Safety and Health (NIOSH), considers two scenarios: (1) a roof bolting machine in the center of the entry for installation of the fifth row of bolts from the face, and (2) a roof bolting machine positioned close to the face for the installation of the last row of bolts. In both scenarios, the bolting machine is placed in an environment which contains 6.0 mg/m3 of respirable dust and is ventilated by a blowing curtain with 3,000 cfm (1.42 m3/s) of air. This environment is used to simulate the roof bolter machine operating downstream of a continuous mining machine. Two operation positions are simulated at the same bolting location: dual drill heads in the inward position for two inside bolts; and dual drill heads in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3/s). INTRODUCTION Roof bolting machines are used to drill bolt holes into the roof of an underground mine at specified patterns and to install roof bolts to secure the roof from falling. At times, the roof bolting machine is also used to install rib bolts; however, only the roof bolting operation was considered in this simulation. Though the roof bolting operation drastically improved the safety of miners from roof falls, some roof bolter operators are experiencing health problems associated with respirable dust. Based on recent statistics [1], following a low point in the late 1990s where the prevalence of coal workers’ pneumoconiosis (CWP) in miners with 25 years or more tenure was approximately 5%, CWP now exceeds 10% for miners with 25 years or more of tenure. In central Appalachia (Kentucky, Virginia, West Virginia), 20.6% of long-tenured miners have CWP and 4.5% have progressive massive fibrosis, the most severe form of CWP. CWP, also known as black lung, is an occupational respiratory disease that has no cure and can ultimately be fatal. The only way to prevent the incidence of black lung is to eliminate miners’ exposure to respirable coal mine dust. Current U.S. regulations require that the overall respirable dust concentration to be 1.5 mg/m3 or less for a full-shift sampling if respirable quartz is not present; otherwise, the standard is 10 divided by the percent quartz (not to exceed the 1.5 mg/m3 respirable dust standard) [2, 3].

Jan 1, 2019

By B. T. Mirabile, D. Tang, Y. Luo, S. S. Peng, C. T. Holland

Knowledge of local coal mine roof geology is critical to the design of a safe and suitable mine structure. An automated drill control and data collection system has been designed for a J.H. Fletcher twin-head roof bolter. Drilling parameters collected during the drilling process can be used to interpret geologic features intercepted in the mine roof. The drill and data collection system have been tested in both laboratory and underground settings. Visualization of certain drilling data has shown good correlation with geology drilled. A quantitative prediction model was developed using drilling parameters examined with data visualization. The quantitative model was tested using laboratory drilling data.

Jan 1, 2004

By Arnold Hammons

Automated temporary roof support (ATRS) systems have been incorporated into roof bolters since the 1970?s. During roof bolting, many injuries have occurred from large pieces of draw rock falling inby the ATRS beam and tipping back into the operator?s area. Other injuries have occurred due to smaller, sharp rocks falling onto the operator?s hand and arm during initiation of roof bolt drilling. These injuries are attributed to weak immediate roof, sometimes called roof skin failure. Even though ATRS systems support the roof and provide a measure of protection against roof skin failure, additional hazards sometimes do exist immediately inby and outby the supported roof. Design innovations such as the ATRS mounted rocker pad deflector systems have been designed to improve the roof bolter operator safety. This paper will inform the reader of the hazards, machine evolution through different design solutions, and the current state of the art in preventing roof skin failure injuries when roof bolting.

Jan 1, 2009

By J. H. Adkins

The goal of the project reported in this paper was to make recommendations for changes in roof bolting procedures and bolter design that would reduce roof bolter accident rates. To that end the project identified the major hazards associated with each task a roof bolter operator per-forms, normalized task accident frequencies. by the time spent on each task, reviewed equipment design features and operating procedures related to the identified hazards and developed recommendations for equipment and procedural changes that would reduce, if not eliminate, the hazards. The research steps completed during the project were: a. A review of related literature and re-search including roof bolting time studies b. The collection and analysis of 1975 accident data pertaining to roof bolter activities c. The normalization of the accident frequency data on the basis of time/task data d. A review of roof bolting equipment e. The development of a field data collection instrument f. The selection of mines for bolter observations g. The collection of field data h. Data analysis and problem specification i. The development of recommendations for corrective measures

Jan 1, 1978

By George K. Martin

This paper deals primarily with roof bolting in Kentucky coal mines from January 1, 1949, through December 31, 1954, a six year period. The Consolidation Coal Co? (Ky.), a division of the Pittsburgh Consolidation Coal Co., began systemmatic roof bolting in November 1948 in Mine #204, Elkhorn #3 Seam, at Jenkins, Kentucky, After the efficiency of roof bolting had been proven by the Consolidation Coal Co., this procedure was adopted by other companies throughout the state. In December 1954, approximately 46.4 percent of Kentucky's total production of coal from underground mines was obtained from roof-bolted areas. Statistics in this report will show the progress made in roof bolting during the six years, in addition to the roof bolting being done as of December 31, 1955. Significant progress has been made in the coal mines of Kentucky in reducing the roof-fall fatality, rates, during the past several years by adopting systemmatic roof bolting. The ground work by the Consolidation Coal Co, (Ky.) in cooperation with the Federal Bureau of Mines was based upon the previous experience of the St. Joseph Lead. Cc, in its Southeastern Missouri Mines and The Tennessee Coal and Iron Division of the United States Steel Corporation. The author gratefully acknowledges the cooperation and assistance given by officials of the various mining firms using roof bolts, the Kentucky Department of Mines and Minerals, and the Federal Bureau of Mines in furnishing photographs and information.

Jan 1, 1958

By Syd S. Peng

According to accident statistics (l, 2), roof fall accidents occur quite frequently at the intersections of underground? openings and account for up to 30% of the roof fall fatalities. But this figure will certainly go up considerably if roof falls not associated with any fatal accident are included in the analysis. Unfortunately, nonfatal roof falls are seldom documented. In the underground coal mines, there are two types of entry intersections. One is the three-way (V type) and the other is the four-way (T type) intersections. A three-way intersection occurs whenever the mainline track haulageway turns at an angle into a section haulageway. The four-way intersections by far the most common type in the U.S. under-ground coal mines are formed by the intersections of two entries which are oriented perpendicular to each other or by the intersections of entries and crosscuts. However, crosscuts are frequently driven at an angle to the entry to facilitate machine movements. The four-way intersections formed by this method of crosscut development are angled. At the intersection of two underground openings, the diagonal roof span is wider than the width of each individual opening. This is one of the major reasons why roof falls occur more likely at the intersections than in the entry between pillars. Consequently, special intersection support plans are usually employed (Figs. 1 and 2) for intersections. The most popular practices are to decrease roof bolt spacing 1 ft. less than or to increase roof bolt length 1 to 2 ft. longer than those employed in the entry between pillars (3). The increase in bolt length or decrease in bolt spacing can be applied to all of the bolts in the intersection or employed only for the strategically located bolts depending on the individual mine practices. These rather generalized practices seems to be adequate for some areas but in many cases inadequate for others. Occasionally, the neighboring two lines of chain pillars are staggered such that the crosscuts in one row of chain pillars face the centers of the chain pillars in the neigh-boring rows. This layout forms T-type three-way intersections which are also inadequate for most weak roofs (3, 4). A study was therefore initiated to develop special techniques for intersection supports. The first phase of the study was the analysis of the stress fields for the underground entry intersections. A three-dimensional stress analysis was necessary for this purpose. Unfortunately, the three-dimensional problems of complicated boundary conditions are beyond the existing analytical methods. The three-dimensional finite element method (FEM) was therefore employed in this study. In the analysis, square pillars of 40 feet wide and an entry height of 8 feet were assumed while entry widths varied at 14, 20 and 26 feet. This model was selected to simulate the mine where roof falls data were collected. The second phase of the study was the collection of field data. The sizes of the roof falls including heights, lengths and widths were collected and analyzed. In the third phase study, the results of the first and second phases were compared and discussed. The analysis of field data revealed an arching zone within which roof falls occurred. The arching zone above an entry obtained empirically was compared with the calculated stress contours. Assuming that the bolts must be anchored in the rock strata outside the arching zone, the preferable systems of bolting were proposed. Also the amount of pretension required to inhibit sliding between layers was discussed.

Jan 1, 1978

By Syd S. Peng

Popular concepts of resin and conventional roof bolting The conventional roof bolt with shell anchor was first introduced for coal mine entry support in the late 1940s. The general concept of a reinforcement mechanism for this type of bolt is suspension. This means the shell anchor must be anchored well inside a competent rock stratum (such as sandstone, limestone or firm shale) so the bolt suspends the underlying weaker strata. This concept has and will continue to dominate the use of conventional roof bolts. Under this concept, the conventional roof bolt is not suitable for the stratigraphic sequences in which a strong, firm stratum is not available within the economic anchorage horizons.

Jan 1, 1994

By S. L. Bessinger

Introduction Extensive testing in the past ten years has shown that where a uniform natural gamma background is present in the strata bordering a seam, the thickness of the boundary coal left in place after mining can be determined by measuring the attenuation of that radiation (Nelson and Bessinger, 1989). Measurements made by the authors in underground mines in Pennsylvania, West Virginia, Ohio, Illinois and Kentucky and by others in Wyoming and New Mexico have shown the presence of such a gamma background (Nelson. 1989). Natural gamma coal-thickness sensors of several configurations have been tested in mines owned and operated by the Consolidation Coal Company (Consol) in Pennsylvania and West Virginia (Nelson and Bessinger, 1988). This paper describes the installation of a natural gamma coal-thickness sensor on an operating continuous miner. Previous tests had shown that the NGB-1000 coal-thickness sensor manufactured by American Mining Electronics, Inc., of Huntsville. AL, is an accurate, mine-worthy instrument. This large gamma detector consists of a sensing head and a control panel. The sensing head contains thallium-doped, sodium iodide scintillating crystal, which is coupled to a photomultiplier tube. The control panel contains the electronic components required for calibration, count conversion and display to the operator. Methods Conditions at a Consol mine in northern West Virginia require that 10 to 15 cm (4 to 6 in.) of coal be left at the roof boundary of continuous miner development sections. This roof coal is required because the shale of the immediate roof is friable and unstable. In the past, operators have used a dirt band that is usually visible near the top of the seam as a guide in maintaining the proper cutting horizon. However, this is not always reliable. Earlier observation showed that the actual thickness of the coal left on the roof varied widely; further, it was noted that occasional, accidental excursions into the immediate roof required supplementary roof control measures, such as installation of planks or center bolts. Thus, it was concluded that operators needed a better source of guidance for control of the cutting horizon, and a roof-coal thickness sensor was scheduled for installation. The NGB-1000 sensor was installed on a Joy 12CM10 continuous miner in June 1988. The sensing head was mounted on the cutter boom of the miner, and the control panel was mounted in the operator's cab. Power for the sensor was initially derived from an intrinsically safe battery power supply. Initial measurements with the sensor showed that the calibration was the same as that used in earlier tests at two other mines, indicating the uniformity of the natural gamma background above the Pittsburgh seam. Operating personnel were initially skeptical of the instrument's accuracy, and were hesitant to use its readings as a guide in maintaining a proper cutting horizon. Because gamma attenuation, the instrument's operating principle, is somewhat abstract, attempts to demonstrate the instrument's accuracy by explaining that principle were generally ineffective. It was found, however, that an operator could usually be convinced of the usefulness of the instrument by placing a large piece of coal of fairly uniform thickness over the instrument's sensing head and allowing the operator to see that the instrument reading increased by an amount very near his estimate of the thickness of the piece. The mine was provided with seven battery power supplies and a charging station. The charging station was kept in the lampman's office, and the mechanic on each shift was instructed that he was responsible for two battery power supplies each day: a freshly charged one to be taken in at the beginning of his shift and a depleted one to be brought out at the end. This system worked well for a few weeks, but eventually some battery power supplies were left in use so long that their batteries were discharged too deeply to allow recharging. In addition, transport and recharging of the batteries represented an additional task for the mechanics, who were already very busy. Consequently, a request was filed with MSHA to allow the sensor to be powered through intrinsic safety barriers by an electronic power supply connected to machine power. The permit was granted, and the sensor was connected to machine power. After the sensor was connected to machine power, the only operating problem experienced was occasional failure of cables. A supply of the required cables was made and delivered to the mine so damaged cables could be quickly replaced. Much of the cable damage could be eliminated by slight modifications to the miner during a rebuild, so that cables could be installed in more protected locations. After the sensor had been in operation for about two months, a survey was made to determine its effect on continuous miner operations. In previous research, coal thickness measurements made in 88 locations by the natural gamma method were compared to measurements made in the same locations by observing drill cuttings and by inspections of drill holes with a borescope. That research showed that the gamma method is at least as accurate as the other two methods (Nelson and Bessinger, 1989) and is also much easier to use. The object of the survey described here was not to assess the accuracy of the natural gamma measurements. but rather to determine the effectiveness of the sensor output as a guide for the operator in maintaining control of the cutting horizon. Thus a smaller, hand-held gamma detector

Jan 1, 1992

Extensive testing in the past ten years has shown that where a uniform natural gamma background is present in the strata bordering the seam, the thickness of the boundary coal left in place after mining can be determined by measuring the attenuation of that radiation (Nelson and Bessinger, 1989). Measurements made by the authors in underground mines in Pennsylvania, West Virginia, Ohio, Illinois, and Kentucky, and by others in Wyoming and New Mexico, have shown the presence of such a gamma background (Nelson, 1989). Natural gamma coal thickness sensors of several configurations have been tested in mines owned and operated by the Consolidation Coal Company in Pennsylvania and west Virginia (Nelson and Bessinger, 1988).

Jan 1, 1990