Search Documents

By William R. Yernberg

Santa Fe Pacific Gold, headquartered in Albuquerque, NM is expanding its operation at the Twin Creeks Mine in Nevada. The $250-million sulfide expansion project, including the Sage Mill, is under construction and is 80% complete. Also, additional mining equipment has been purchased to haul the sulfide ore to the mill. With the expansion, employment at Twin Creeks is expected to reach approximately 970 people by the end of 1996. Santa Fe Pacific Gold now owns and operates three gold mines in the United States and is involved in several other gold projects. The three currently operating mines are the Twin Creeks, Mesquite and Lone Tree mines. The Mesquite Mine is located in California’s Imperial Valley. Lone Tree is located 55 km (34 miles) southeast of Winnemucca, NV. The company’s total gold production from these operations is expected to be in the range of 26.3 to 26.6 t (845,000 to 855,000 oz) in 1996. This compares to a total production of about 124 kg (4,000 oz) for the company in 1989. Production costs range from $6.90to $7.25/g ($215 to $225/oz). At the end of 1995, the company reported proven and probable reserves of 556.7 t(17.9 million oz) of gold.

Jan 1, 1996

By J. A. Cole

The mill project at Lone Tree was commissioned in October, 1993, followed by the commissioning of the autoclave pressure oxidation circuit in February, 1994. Discussion of the first year of milling operations at Lone Tree is presented. The mill is currently operating above the design rate of 2,267 mt/d (2,500 st/d). Both phases of the start-up were essentially trouble free. The few problems that were encountered and the respective solutions are addressed.

Jan 1, 1995

By Lorenzo Pellegrini

The respect of EPB reference pressure during TBM advance and hyperbaric activities, the complete and effective filling of the annular gap between tunnel lining extrados and the excavation section and a well organized monitoring system, to control surface settlements and ground distortion, are items of utmost importance in EPB tunnelling process. The paper describes how these concepts have been applied while excavating in the difficult underground conditions found at Sao Paulo (Brazil) during the execution of the Sao Paulo Metro Line 4-Lot 1. In this project, the annular gap has been filled by two components type, cement grouting. The back feed of the extensive monitoring campaign carried out to check the surface settlements during the excavation and hyperbaric maintenance operations will also be described in the paper.

By Gilles Cachia, Foteini Vasilikou, Seth Pollak, Hannes Lagger

"INTRODUCTION The Shatin to Central Link (SCL) is a new rail line being constructed by the MTR Corporation for the Government of Hong Kong to cater for the growing passenger demand between the North-East New Territories and the urban areas of the city. Contract 1103, which will provide the 4 km of running tunnels between the new Hin Keng and Diamond Hill Stations, was tendered in a design-build framework and awarded to Vinci Construction Grands Projets (VCGP) in October 2012, with Arup as Vinci’s lead designer. One of the most challenging pieces of work on the contract involved the construction of 133m of SEM mined tunnel on the northern end of the project. The Northern Mined Section (NMS) is an undrained, twin-track, single bore profile, broken out through the southern pipe pile wall of the Hin Keng Station cut-and-cover box, Figure 1. The tunnel has maximum excavated dimensions of 14.5m span x 12m height, with track spacing of 6.175m. The general excavation sequence consisted of 3 stages; a 6m high top heading (73.1m2), followed by bench (27.3m2), and invert (26.7m2). A risk-based approach to the design was taken given the large variation in rock level, cover, and an active stream course above tunnel crown. Ultimately, six different temporary support types were utilized in order to optimize the construction process through continually changing ground while maintaining a safe and stable excavation. Three main support types were developed during the initial design phase, along with a “contingency” case, which utilized a partial heading excavation sequence and enhanced face support. The purpose of the contingency support type was to have a robust, engineered design available for immediate implementation should unexpected ground behavior develop, leading to the breaching of instrumentation trigger levels. This support type was never implemented on site. Drill- and-blast tunneling commenced once 6m of rock cover was verified through forward probing. A robust instrumentation and monitoring scheme provided valuable data throughout excavation and the means to carry out a geotechnical back-analysis of the ground behavior and support performance."

Jan 1, 2016

By E. C. Ekedahl, R. J. Heath

Introduction Potassium, together with nitrogen and phosphorous, is an essential nutrient required for growth. Since all living things need potash, the major demand for potash - about 95% of the total - is as a fertilizer. Agricultural productivity has increased dramatically in recent times. This increase in crop yields requires substantial amounts of added nutrients to keep the soil fertile. It follows then that potash will always be in demand. There is no substitute. Other fertilizers that contain phosphorous (P) and nitrogen (N) are complementary and not competing products. Fireplace ashes (pot-ashes) have a relatively high potassium content. Their value as a fertilizer had been recognized for centuries. But today's potash industry did not begin until deposits of potassium-rich ore were discovered and exploited in Europe during the 19th century. Canadian potash development Potash in Saskatchewan was first recognized in 1943. It was discovered as a byproduct of an oil exploration program. But it was several years later before the existence of a major commercial deposit was acknowledged, and not until 1951 that the first attempt at development occurred. That attempt was unsuccessful. The shaft flooded and was abandoned. It did, however, demonstrate the need for new technology to penetrate the waterlogged Blairmore layer. This was eventually developed and the first mines were brought into production in the early 1960s. Once the technology was available, and the extent and quality of the potash beds became known, a number of companies proceeded to develop mines. By 1970, seven mines were in operation and three more were nearing completion. Combined, total capacity then was 7.6 Mt/a (8.4 mil¬lion stpy) K20. At that time, world potash consumption was about 15 Mt/a (16.5 million stpy). This increase in supply from Canada produced a large potential surplus that shattered the prevailing balance between supply and demand. Although world demand increased steadily throughout the 1960s and early 1970s, it was several years before world supply and demand were again in balance. Saskatchewan capacity has been expanded a number of times. It now stands at 10.7 Mt/a (11.7 million stpy) K20. Actual production has not approached this figure, however. Two new mines in New Brunswick have recently been built with a combined annual capacity of 1.2 Mt (1.3 million st) K20. Total Canadian capacity of about 12 Mt/a (13 million stpy) now amounts to 30% of world capacity. Central offshore marketing organization Canadian Potash Exports Ltd. (Canpotex) was created in 1970 as the offshore marketing organization for Canadian producers. Canpotex is owned by Saskatchewan producers and is their exclusive marketing organization for offshore business. Each company handles its own sales in Canada and the US, but all sales to other markets are handled through and by Canpotex. The Saskatchewan industry has an ore body of a size and consistency unmatched anywhere in the world. Large efficient mines have production costs that compare favorably with other producing countries. On the minus side, Saskatchewan is remote from most major markets. It therefore needs the ef¬ficiencies that stem from one organization that coordinates all offshore shipments and minimizes distribution costs. Agriculture guides potash market In the period following World War II, potash was a classic growth industry. World demand increased each year from 1945 to early 1970s. Since then, demand has been more erratic. Some years show substantial increases, but are followed by significant declines. For about the last decade, the pattern has been unclear and future demand has become correspondingly difficult to predict. North America and Europe together account for about 40% of the world potash consumption. In both areas, farming is characterized by surplus production, declining crop prices, and expensive government support programs. Under those circumstances, farmers respond by minimizing input costs. Fertilizer is one of the items they reduce. Potash is retained in the soil. It is possible to reduce potash application with no immediate deterioration in crop yield. The lower yields occur only when potash levels are depleted. So, farmers can econo-

Jan 12, 1987

Remote sensing methods have been used to evaluate vegetative growth patterns for many applications, though relatively little work has focused on tracking mine reclamation progress. For coal mines in Central Appalachia, reclamation approaches that include production of biofuel feedstocks are increasingly attractive, as these may yield significant post-mining land values and contribute to carbon-neutral energy supplies. To optimize productivity, the influence of reclamation parameters must be well understood ? which necessitates tracking biomass production over long time periods. Satellite-based estimations may offer low-cost alternatives to conventional biomass appraisals, and also the potential to provide critical input for carbon accounting at varied spatial scales. In this paper, we use biomass production experimental plots on reclaimed mine sites established by the Powell River Project (PRP) for a comparative study between satellite measurements of Normalized Difference Vegetation Index and inventory estimates of biomass under a variety of conditions. The PRP is a unique public-private partnership in the coalfields of southwestern Virginia dedicated to enhancing beneficial use and environmental protection of mined lands.

Feb 27, 2013

Remote sensing methods have been used to evaluate vegetative growth patterns for many applications, though relatively little work has focused on tracking mine reclamation progress. For coal mines in Central Appalachia, reclamation approaches that include production of biofuel feedstocks are increasingly attractive, as these may yield significant post-mining land values and contribute to carbon-neutral energy supplies. To optimize biomass productivity, the influence of reclamation practices on biomass production must be well understood, which necessitates tracking biomass production over long time periods. Satellite-based estimations may offer low-cost alternatives to conventional biomass estimations and, also, the potential to provide critical input for carbon accounting at varied spatial scales. In this paper, experimental biomass production plots on reclaimed mine sites established in Wise County, VA, are used for a comparative study of satellite spectral derivatives, which are evaluated against groundbased biomass estimates. Metrics based on four spectral derivatives, band ratios and spectral transforms were regressed against biomass measured in situ for different species. The results demonstrate that greenness and principal component 2 (PC2) were more efficient than the other spectral derivatives for monitoring the biomass of this reclaimed area. Also, it is shown that Landsat-5 TM has provided promising results for monitoring of the biomass changes occurring from 2008 to 2010 over the study area.

By K. Deaton

"INTRODUCTION A packaged cooling system is being developed for refuge alternatives (RAs) that meets MSHA qualification guidelines for deployment in coal mines. This system will allow full occupancy ratings of deployed Refuge Alternatives (RAs) to be maintained by keeping the apparent temperature inside the RA from exceeding 95°F. Research investigations sponsored by NIOSH have shown that heat buildup caused by occupants in mobile RAs will result in apparent temperatures that exceed the 95°F limit established in 30 CFR 7.504. Figure 1 shows the temperature rise in an inflatable RA having an occupancy rating of 23 people at an 81°F mine air temperature. This plot shows the need for either heat mitigation or occupancy derating in warmer mines. The RAECS will be designed to provide enough heat mitigation to eliminate occupancy derating due to heat buildup over the 96 hour refuge period.This paper describes testing of a prototype cooling system that uses proven vapor compression technology powered by batteries to keep the RA interior below the 95° limit for a minimum of 96 hours. Testing of this prototype cooling system was conducted in December of 2015 and January of 2016 at the NIOSH test mine in Bruceton, PA. December testing was conducted at the prevailing mine ambient temperature – approximately 60°F. The January testing was done with the mine ambient temperature in the immediate vicinity of the RA artificially elevated to 85°F. Realistic heat gain from RA occupants was provided by human simulators developed by NIOSH. These simulators add sensible heat corresponding to human metabolic processes and latent heat generated by respiration and perspiration. Heat generated by CO2 scrubbers was also added. Results of cooling system performance using these simulated loads at the two ambient conditions are described. A comparison of the apparent temperature in the RA using two different control techniques is also presented. This work documents the ability of the cooling system to meet the established apparent temperature limit at the full occupancy rating of a six person RA. A new cooling system intended for use with existing RA deployments and having greater cooling capacity is currently in development and will be described."

Jan 1, 2017

By W. E. Falck, A. Usubiaga, J. Spangenberg, P. Schepelmann, S. Šolar, D. Wittmer, F. Blanchard

The extraction and processing of mineral resources may be accompanied by environmental impacts. In spite of technological advancements, the enormous increase in production volumes within the last decades has induced sizeable environmental impacts along the life-cycle of products. Beside environmental impacts, social issues associated with mining need to be considered to ensure the social acceptability of mining activities. The project EO-MINERS aims at deploying Earth Observation (EO) tools to inform best practices in mining and to thus assist the global mineral resources industries in their transition to sustainable development. In order to facilitate the handling of complex sets of information requirements from a wide variety of stakeholders, a set of indicators was developed that will inform the process of EO tool and services development. The project strives to enable stakeholders outside the industry to meaningfully participate in decision-finding processes on mining-related issues by developing and providing EO products and services that fit the information requirements. The project has identified a wide range of such information requirements by stakeholders that could be potentially provided by EO tools. The applicability of the EO tools on the local level is tested on three mining sites.

Jan 1, 2011

By Kenneth Deaton

"A packaged cooling system is being developed for refuge alternatives (RAs) that will meet U.S. Mine Safety and Health Administration (MSHA) qualification guidelines for deployment in coal mines. This system will allow full occupancy ratings of deployed refuge alternatives to be maintained by keeping the apparent temperature inside the RA from exceeding 35° C (95° F).Research investigations sponsored by the National Institute for Occupational Safety and Health (NIOSH) have shown that heat buildup caused by occupants in mobile RAs will result in apparent temperatures that exceed the 35° C (95°F) limit established in 30 CFR 7.504.Figure 1 shows the temperature rise in an inflatable RA having an occupancy rating of 23 people at an 27° C (81°F) mine air temperature. This plot shows the need for either heat mitigation or occupancy derating in warmer mines.The Refuge Alternative Environmental Control System (RAECS) will be designed to provide enough heat mitigation to eliminate occupancy derating due to heat buildup over the 96-hour refuge period.This article describes testing of a prototype cooling system that uses proven vapor compression technology powered by batteries to keep the RA interior below the 35° C (95° F) limit for a minimum of 96 hours. Testing of this prototype cooling system was conducted in December of 2015 and January of 2016 at the NIOSH test mine in Bruceton, PA. December testing was conducted at the prevailing mine ambient temperature — approximately 15.5° C (60° F). The January testing was done with the mine ambient temperature in the immediate vicinity of the RA artificially elevated to 29° C (85° F). Realistic heat gain from RA occupants was provided by human simulators developed by NIOSH. These simulators add sensible heat corresponding to human metabolic processes and latent heat generated by respiration and perspiration. Heat generated by CO2 scrubbers was also added. Results of cooling system performance using these simulated loads at the two ambient conditions are described. A comparison of the apparent temperature in the RA using two different control techniques is also presented. This work documents the ability of the cooling system to meet the established apparent temperature limit at the full occupancy rating of a six person RA. A new cooling system intended for use with existing RA deployments and having greater cooling capacity is currently in development and will be described.Expendable desiccant modules were also used to provide supplemental water vapor removal and their role in mitigating cooling load is addressed."

Dec 1, 2016

By W. F. McDermott

The transportation of solids by pipeline is not new. In 1891 a United States patent broadly covering a method of pumping coal with water was granted to W. C. Andrews. His pilot plant was constructed on what is now the site of the New York Public Library in Manhattan. His process was applied to pumping coal mine waste back into the worked out portion of coal mines. On October 26, 1967, the world's first long distance iron ore slurry line was put into service by Savage River Mines. The commissioning of this 5.0 million dollar installation climaxed three years of development, testing, and construction and proved the Company's faith in pioneering this unique transportation method for iron ore. This paper will discuss some of the more pertinent items in connection with that three- year period. Also to be discussed will be the operation of this line during the past eleven months.

Jan 1, 1968

By W. J. Kennedy, John D. Gardner

Introduction During the past 10 years, energy costs in mining have risen from about 4% to as much as 25% of total production cost. When combined with declining ore grades, these costs exert inordinate stress on mine productivity. Industrial engineering techniques have traditionally been aimed at improving manufacturing facilities productivity, but they have been applied to mining as pressure for productivity improvement has increased. These techniques can perform four useful functions for mining operations by improving methods, equipment selection procedures, energy use through scheduling, and managing energy costs rather than being managed by them. This article discusses some of the standard techniques for productivity improvement, and how they can be adapted to perform these four functions. Pre-Production The best time to seek high productivity is when a mine is being planned. During pre-production, when most options are still open, an optimum mine design is achievable. At this time, major equipment selections are made, the layout, material handling systems, and processes are designed, and critical energy source decisions are made. By including explicit energy cost projections, decisions can be made that will save significant amounts of money per ton of ore over the life of the mine. Attention can also be given to often overlooked details such as lighting. Some of the same tools used in new mine planning are applicable to productivity improvements at an existing plant. These tools are the charting and modeling methods that have been developed by industrial engineers over the past 75 years. Energy Consumption Before any analysis of energy consumption can be performed, preliminary work is necessary to find the kind of energy used, how much it costs the plant, and when electrical peaks occur. Past bills should be examined to determine the monthly consumption rate and the cost of each energy type. These data should be adjusted to remove effects caused by production fluctuations or weather. Knowing when electrical peak demands occur is necessary because these determine either the electrical capacity needed or the amount that must be bought. At $500-$800 per kW for construction or $5-$15 per kW per month for purchase, they represent a significant cost. By the time these data are collected, planners should be aware of the importance of energy in the total cost of mine operation, and should have the most crucial time data for electrical peak demand. Flow Process Chart Reducing costs can be accomplished by a thorough look at mine systems and how altering one system causes changes in others. By developing and exercising models of production processes outward to the transportation of the final product, otherwise obscured weaknesses may become apparent. There are tools available for analyzing the mine and its associated systems; one of the most useful is the flow process chart. The flow process chart gives a system analysis of a production procedure by classifying all actions into one of five types: operations, inspections, transportation, delays without paperwork, and delays with paperwork. Operation: In an operation, the nature of something is changed. Examples are blasting, washing coal, and processing matter. Denoted by 0. Inspection: Examining an object for identification or to measure some attribute. Examples are determining whether a drill hole is deep enough, deciding how far to cut under an unsupported roof when operating a continuous miner, or checking the lubricant level on a truck. Denoted bye. Transportation: Moving an object from one place to another. Examples are transporting overburden, moving coal on a conveyor belt, and pumping water. Denoted by =>. Delay without paperwork: A delay that is an inherent part of the system. Examples include idle time of a continuous miner while waiting for shuttle cars or for roof bolting, crushed ore in a storage area waiting for grinding and flotation, and people from one craft waiting for another craft to finish. Denoted by D. Delay with paperwork: A delay that can be terminated only by some written authorization. Examples are coal that cannot be removed until authorized by a bill of sale and transportation orders, personnel records, maintenance, or spare parts. Denoted by V. In practice, the flow process chart is completed after data collection and a detailed examination of the process. Data collection is needed to answer questions on distance, quantity, and time for each of the operations. As the analysis is being performed, each step of the process is subjected to these questions: • Why is the step necessary? • What is being moved? • When does the step take place, and why?

Jan 11, 1983

By D. N. Thompson, R. L. Sayer, K. S. Noah

Economical remediation of acid rock drainage (ARD) at secluded high-altitude western ore mines is difficult given the current treatment technology. Several passive-engineered systems that are based on wetland technology were tested in the laboratory with three western ore mine ARDs (Co, Cu and Fe mines) and with a copper leachate effluent. These systems used well-weathered lodgepole pine sawdust as the sole carbon source and mud from a pond at one of the mine sites as the source of sulfate-reducing bacteria (SRB). Simple one-pass flow-through systems removed 44% to 99% of the vari¬ous heavy metals front the Co and Cu mine ARDs and increased the pH from 3 to 7 after 28 days of SRB acclimation with a five-day residence time. Carbohydrate utilization rates were generally low, except for one 437-day run, which consumed 25%, 30% and 21 % of the cellulose, hemicellulose and lignin, respectively. Initial pH, amounts of toxic heavy metals and the degree of predegradation of the sawdust were found to significantly affect both remediation potential and acclimation time. Engineered SRB systems, alone or in combination with other passive technologies, offer promise for the economical remediation of western US ore mine ARDs.

Jan 1, 2000

By Jason Swartz, Gerardo Gomez, Henry Leighton

San Antonio has experienced sustained growth for decades, putting increased pressure on existing wastewater infrastructure. In June 2013, San Antonio Water System (SAWS) reached a Consent Decree agreement that requires significant improvements to the wastewater system over a 10-year period to reduce Sanitary Sewer Overflows. One of the critical projects was the W-6 Upper Segment Tunnel project to reduce sanitary sewer overflows on an existing sewer main running through Lackland Airforce Base. The replacement project consisted of a new tunnel nearly 29,000 LF of primarily 104" FRP. The project also includes nine shafts and multiple trenchless crossings to make near surface connections to the new works.

Jun 23, 2024

By Brian K. Failon

Scale formation is a problem that affects many mineral processing systems because the processes require the use of large volumes of water. Scale composition may vary from circuit to circuit, but the scale deposition mechanisms and needs for prevention are often somewhat similar. Likewise, there is a degree of commonality in the prediction, detection, and elimination of scaling conditions in various water systems. This paper briefly reviews some of the conditions which lead to scale formation, as well as some of the common problems associated with unchecked scale growth. The primary focus of the paper is on the variety of chemical scale inhibitors available for use in mineral processing circuits, and the actions of each type. The means of predicting and detecting scaling tendencies are also addressed, and include both direct and indirect methods, i-e., stability index determination and chemical analysis of deposits.

Jan 1, 1986

By Michael N. Allenby

One of the least discussed areas in the ever-improving technologies of gold recovery from ore bodies and tailings is the chemistry of the waters used in the plants. Carbon-in­ pulp, carbon-in-leach, heap/dump leaching and iological oxidation processes are all affected by water quality. The remoteness of a lot of the plants means that the large water requirements can often only be met by a ground water source. The chemistry of waters from different sources poses different problems, but generally a lot of these waters are scale forming. Scale-forming tendencies can be described by calcium, magnesium, barium and strontium assays. They can be notated by Langelier and Ryznar indices. They can be plotted by computer programmes that print out scaling indices at different conditions. The propensity to scale can -be readily determined. The prevention of scaling -or at worst minimisation of scaling -is the ambition of the suppliers of scale inhibition programmes. This prevention/minimisation technology is discussed below.

Jan 1, 1993

By J. S. Roti

Calcium-based scale precipitation is a common problem in mill reclaim waters. An accumulation of these adherent deposits can result in a rapid reduction in water flow, loss of pump efficiency and eventual interruption in ore production. Heap leach applications can also experience the added problems of plugged sprinkler heads, blinded leach pads and fouled carbon columns when scale control is not maintained. The primary cause of scaling in precious metal recovery is the relative insolubility of calcium carbonate. The presence of the calcium ion and bicarbonate alkalinity is common in almost every water source. If the temperature or pH of the water is allowed to increase, the bicarbonate breaks down to carbonate and combines with calcium by the following reaction: Ca +2 +2HCO3 ? CaCO3 + H2 + CO2

Jan 1, 1986

By James Y. Oldshue, Paul M. Kubera

Most coillillercial processing applications employing mixers in various types of slurry systems are continuous flow. These applications may also be multiple stage, with the stage number varying anywhere from two or three to ten or more. Two questions that usually come up at the beginning of any proposed pilot plant study are (1) can the pilot plant unit be operated batch-wise, and the results extrapolated both on the basis of scale and fluid motion to the full-scale tank which will be continuous-flow (and probably multi-stage), or (2) does the pilot plant need to be operated in a continuous-flow fashion, and if so, does the exact number of tanks/stages that are proposed for the plant need to be used in the pilot plant? We will consider these possibilities in sequence and present the principles involved in running some of the various pilot-plant arrangements.

Jan 1, 1992

By Gerd Oberheuser, Hans Kellerwessel

Comminution with high compression roller mills finds rising interst in ore and minerals industry. Energy saving and upgrading of existing grinding facilities is one of the main reasons. Beside these possibilities other positive effects on the downstream units operations require also intense testwork. Basic interdependencies of the operational parameters gained at the testwork and their influence on the upscaling procedure are described.

Jan 1, 1995

By M. J. Friedel

The scale-dependent hydraulic properties in a fractured porphyry copper oxide deposit are investigated for relevance to In Situ Leach Mining (ISLM) design. In most well field designs, mine operators assume that hydraulic properties represent a continuous spatial function, or continuum. The problem, however, is that the representative elemental volume, the volume over which hydraulic properties are described as a continuum, is a domain (if it exists) that occurs between end members representing varying degrees of heterogeneity. At the Cyprus Casa Grande mine, transmissivity fluctuations are spatially correlated. This suggests that, at the scale of ISLM, the hydraulic process is heterogeneous, and a typical continuum representation is inappropriate for design. Alternatively, a conditional stochastic approach using the Simulated Annealing (SA) technique is deemed useful for the imaging of heterogeneous hydraulic properties. Specifically, SA preserves transmissivity extremes and spatial complexity, both necessary for accurate conditioning of a flow simulator. Also, the stochastic continuum approach provides an avenue whereby uncertainty (or risk) may be addressed. Currently, the SA weaknesses are that it is computationally time consuming and that uncertainty may increase when simulating under conditions of statistical isotropy. Recognizing that ISLM exerts a dynamic influence on hydraulic properties with time, the mine design should be re-evaluated at intervals throughout the evolution of the leaching process.

Jan 1, 1994