Search Documents

By S. E. Phillipson

During the course of evaluations by the Mine Safety and Health Administration’s Roof Control Division, the controls on ground instability were investigated at surface and underground limestone mines throughout the eastern and southern United States. Structural geologic features, including joints and faults, were identified by basic geologic mapping as primary controls on highwall and back instability in surface and underground limestone mines. By comparing the spatial orientation of discontinuities and internal angle of friction with the orientation of highwalls on a stereonet, the potential for sliding, toppling, and raveling failures was evaluated in a semi-quantitative fashion. Structural geologic mapping identified faults and joints, which dismembered the back and were associated with ground instability, in underground mines. This paper documents the importance of recognizing structural geologic controls on ground stability in limestone mines, advocates basic geologic mapping as a critical component of ground control programs at surface and underground limestone mines, and provides examples of simple stability evaluations using the stereonet method.

Jan 1, 2006

By Raymond Sandiford, Taehyun Moon

"In 2012, Superstorm Sandy (Sandy) caused extensive flooding in many of the tunnels in New York City. The inundation resulted in two distinct stress changes to the tunnel structures. The first stress change was water pressure on the inside face of the tunnel lining. The second condition related to the change in buoyancy of the tunnels. In areas where the tunnels were supported on rock and an adjoining area supported on soft soil, overstress issues arose. Numerical analyses were performed to assess the structural impacts of the tunnel water inundation; especially stress changes due to internal pressure as well as changes resulting from the buoyancy effects. The paper will discuss the assessment process and its results; it will demonstrate that the change in internal pressure were of little consequence, however the change in buoyancy resulted in significant increases in bolt stresses. INTRODUCTION Superstorm Sandy caused tens of billions of dollars in damage in the NYC metropolitan area. It also caused significant disruption to the transportation system by flooding most of the under river tunnels servicing Manhattan from the outer boroughs and New Jersey. The rehabilitation of the tunnels was of paramount importance to the restoration of the NY and NJ economies. With this rapid restoration, it was essential to determine whether the flooding of these tunnels caused damage to tunnel structures. A series of analyses were undertaken to ascertain whether the change in the stress conditions and buoyancy of the tunnels, due to the flooding, was significant enough to cause damage or over-stressing of the tunnel components. The effects of this unforeseen loading condition was a concern to the agencies operating these tunnels and were thus analyzed to ascertain if there were any adverse impacts. This was a concern because the majority of under river tunnels in NYC was built earlier in the century and constructed using bolted cast-iron lining segments. The cast iron, although quite strong in compression, is much less so in tension. Also, after nearly a century of use, the bolts connecting these segments together have under gone varying degrees of corrosion. The stress changes in both the liner segments and the supporting bolts were estimated for conservative ground support conditions to provide confidence that the flooding had not caused permanent damage."

Jan 1, 2016

By Robert N. Evans, Delon Hampton

During construction of the Washington Metropolitan Area Transit System, the hand-mining of a mixed-face condition was anticipated on a portion of tunnel located in the downtown area of Washington, D.C. The Section, consisting of two circular tubes, extends from Station 12+80, heading in a westerly direction, traverses along a curve under Lafayette Square, and ends in a northwesterly direction at Station 37+62 (see Fig. 1a). It was near the northernmost portion of the section that the mixed-face condition was encountered. Decomposed rock was first encountered in the invert at Station 31+00. From this point the rock gradually increased in height until it intersected the springline at Station 37+62, the project limit. Summarized within this paper are measurements of the soil load on a horseshoe-shaped portion of tunnel located in the mixed face condition. These measured loads are compared to the soil load on tunnels as determined by current design methods. The paper also discusses rib and surface movements associated with the post loading process. Comments will be made on how the presence of a mixed face condition might help or hender the tunnel design and construction procedures.

Jan 1, 1974

By Ingo Kaundinya

"INTRODUCTION Tunnels are important elements of the German federal road network which have to cope with an increasing traffic load especially of heavy goods vehicles. In order to ensure a high availability and safety level for these key infrastructures, big efforts are required by owners and operators in order to keep all infrastructures up to date. This mainly relates to current European regulations regarding tunnel safety (Directive 2004/54/EG) [1] and their national implementation, which must be fulfilled by many existing tunnels. In this context the German Federal Government spends more than 1.1 billion € for the structural and operational retrofitting of more than 120 existing road tunnels. As many of these projects have recently been finished or are still under progress, experiences and best practices could be reported. After the description of current requirements in national standards regarding structural fire protection, the paper gives an example for an upgrade of a tunnel’s fire protection by installing an additional fire protection system, which is a quite costly measure. Another possibility to fulfill current requirements regarding structural fire protection could be the numerical proof of sufficient bearing capacity of a structure. The influence of different fire loads and fire durations on the bearing capacity of typical road tunnel structures have been investigated in a research project funded by the German Federal Ministry of Transport (BMVI) and coordinated by the Federal Highway Research Institute (BASt). The results of this research project have been used to define a procedure how to investigate existing tunnels regarding structural fire protection. Finally, the research results have also been the basis for a current update of national standards for tunnel construction. REQUIREMENTS REGARDING STRUCTURAL FIRE PROTECTION The structural fire protection design of road tunnels is usually based on temperature-time curves of exposure to fire, for simplicity called ""fire curves"". The fire development after fire growth is illustrated with fire curves. Fire curves can be subdivided into a heating-up phase, a fully developed fire phase, and if applicable, into a cooling-off phase (cf. Figure 1). During the fully developed fire, the fire remains at a certain temperature level."

Jan 1, 2016

By R. Kneisley, D. Conover, K. Haramy, K. Hanna

INTRODUCTION Coal mine entry intersections are high-risk areas for roof falls due to inherently wide roof spans, excessive stress, and variable intersection shapes resulting from breakthrough misalignments. Statistics from underground coal mines reveal that a high percentage of injuries occurs from roof and rib falls in entry intersections (Peng, 1980). The U.S. Department of the Interior, Bureau of Mines, is conducting a field research project to investigate failure modes surrounding underground coal mine entry intersections. The research objectives are to (1) develop a method to determine failure modes and stress-displacement relations around coal mine intersections and (2) develop engineering guidelines and empirical relationships for use in designing safer coal mine entry intersections. The basic approach to achieve the objectives is to instrument and monitor intersections before, during, and after intersection development in order to determine contributing parameters, such as in situ stresses, stress changes, strata movement, geology, physical properties, and mining sequence, that may influence the short- and long-term stability of the intersection and adjacent entries. This paper describes a rock mechanics instrumentation program, data analyses, and a comparison of two case studies conducted at two underground mines, designated as "A" and "B", in the Illinois Coal Basin. The instrumentation plans and data collected during development and long-term monitoring of four-way intersections and adjoining entries are presented. Data analyses of pre- and post-mining roof stress, pillar loading, strata movement, roof bolt loading, and geologic features are included. INTERSECTION FAILURE MECHANISM The region surrounding an entry intersection is characterized by different failure criteria than the region surrounding a single entry. Stresses induced during intersection development may result in a high incidence of roof and rib failures. Various numerical modeling techniques have been used to evaluate the failure modes surrounding intersections (Gercek, 1982; Chugh et al., 1975). Numerical modeling techniques include problems associated with the analysis of post-failure behavior, provision for different horizontal stresses (i.e., 01 f 021, and determination of inputs required for any non-elastic behavior. It seems likely that more sophisticated failure criteria, based on actual field data, are needed. The Bureau of Mines has conducted an extensive instrumentation program to investigate actual intersection failure mechanisms and to provide an improved understanding of stresses and deflections using beam and plate theories. Beam theory is not applicable to analyzing intersections (Wright et al., 1964); however, it can be used to explain roof deflection and failure (shear and flexure) of adjacent entries and to provide an improved understanding of stress changes and displacements as the entries, crosscuts, and intersection are developed (Hanna et al., 1985). Beam theory may be used for entries when the roof length is twice the width. When the length is less than twice the width (as in intersections), the roof must be analyzed as a three-dimensional problem, and stress and deflection calculations are based on flat plate theory (Adler and Sun, 1976). The confined-core theory (Wilson, 1972) hypothesizes that within a typical pillar, two regions exist: a confined-core region where the horizontal confining pressure is uniform and approximately equal to the overburden pressure, and a yield zone where the vertical pressure increases from nearly zero at the rib to a pressure peak at the boundary of the yield zone. The strength of coal in the yield zone ranges from nearly zero at the rib to nearly full strength at the confined core. The vertical stress in the confined core decreases from maximum at the yield zone boundary to the overburden pressure some distance into the pillar. Excavation of the adjoining entries

Jan 1, 1986

By Keshavan Nair

In connection with Project Payette, which is concerned with the detection of underground nuclear explosions, it was necessary to determine the technical feasibility of constructing and maintaining a large (approximately 315 feet in diameter) unsupported underground cavity at a depth of approximately 2700 feet in the Tatum Salt Dome in Mississippi. The dimensions and the location of the cavity in the salt dome were governed by criteria laid down by the Atomic Energy Commission. Within the framework of the specified criteria, cavities of various shapes and dimensions could be utilized. One aspect of the feasibility study was to investigate the structural stability of various cavity shapes and to recommend a preferred shape. This paper summarizes the studies that were conducted to evaluate the structural stability of various proposed cavities.(l)

Jan 1, 1968

By W. Blake, J. K. Whyatt, B. G. White

In situ stress on the scale of a tunnel or mine may be distorted by geologic structures. The resulting variations in in situ stress have a direct bearing on the potential for mining-induced seismicity. New evidence collected from the Lucky Friday mine by US Bureau of Mines researchers, as well as a review of previous case studies, demonstrated that in situ stress variations affect the [spatial] distribution of mining-induced seismicity. Although overcore stress measurements have been useful in these studies. they are too expensive and, depending, on conditions, may be too difficult to collect. However, information on borehole and raise breakouts: deformation of mine openings: and patterns of seismicity, ground-control problems and rock-burst damage can be used to build a stress database. In conjunction with maps of mine structure and geology and models of rockmass behavior, this database can then be used to build a map of in situ stress variations. Such a map could provide a means of anticipating patterns of mining-induced seismicity and. Thus, could be the basis for planning appropriate measures to ameliorate rock-burst hazards.

Jan 1, 1997

By J. K. Whyatt

In situ stress on the scale of a tunnel or mine may be distorted by geologic structures. The resulting variations of in situ stress have a direct bearing on the potential for mining-induced seismicity. New evidence from the Lucky Friday Mine collected by U.S. Bureau of Mines researchers, as well as a review of case studies, demonstrates that in situ stress variations affect the spatial distribution of mining-induced seismicity. Although overcore stress measurements have been useful in these studies, they are too expensive and, depending on conditions, may be too difficult, to use routinely in mapping stress variations. However, information from borehole and raisebore breakouts; deformation of mine openings; and patterns of seismicity, ground control problems, and rock burst damage can be used to build a stress database. This database can then be used in con-junction with maps of mine structure and geology and models of rock mass behavior to build a map of in situ stress variations. Such a map provides a means to anticipate patterns of mining-induced seismicity that are likely to be encountered and, hence, provide a means for planning appropriate measures to ameliorate rock-burst hazards.

Jan 1, 1995

By John Murray, Ryan Smith, Daniel Ebin, Robert Gould, Thomas Hennings

The Atlanta Plane Train Tunnel West Extension was excavated at Hartsfield-Jackson Atlanta International Airport using Sequential Excavation Methods (SEM). At its shallowest point, tunnel cover to bottom of Domestic Terminal footings was limited to 6 feet in soft ground. To mitigate risk of excessive building movement due to tunneling-related activities, the columns near the alignment were directly underpinned. Underpinning was accomplished using a combination of grouted mini-piles, installed under low headroom conditions, that supported steel framing spanning over the tunnel excavations. This paper focuses on design and construction of the underpinning system used to mitigate risk from tunneling.

Jun 13, 2023

By K. Sharman

Quintette Coal Limited (managed and 50% owned by Denison Mines Limited) operates an open pit coal mine located in northeastern British Columbia, in the foothills of the Rocky Mountains. (See Fig. l). Mining commenced in 1982. The mine currently produces 4.75 million tonnes of medium volatile bituminous coal per year from three pits (Mesa, Wolverine and Shikano), using a truck/ shovel operation. (See Fig. 2). Conveyors and trucks transport run-of-mine coal to the heavy media/froth flotation process plan t, where it is cleaned and loaded into rail cars for delivery to the Ridley Island port at Prince Rupert, British Columbia. All coal is sold to the Japanese steel industry under a long term contract. The coal seams mined at Quintette are contained in the Lower Cretaceous Gates Formation. Mineable seam thicknesses vary from 0.6 m to 10 m. The regional structure of the area is typical of foreland fold and thrust belts, with open to tight folds and imbricate thrust faulting. The range of structural features found in the three pits, and their effect on mining, forms the subject of this paper.

Jan 1, 1991

By R. L. Atwood

The structure, properties, and composition of commercial chelating-type copper extractants are examined. Characterization of these extractants was accomplished using organic separation techniques and analytical tools such as NMR and IR. Results indicate that only the trans isomer of the diphenylhydroxyoxime (LIX (R) 64N) is capable of copper chelation. The effect of the structural modification of the extractants on the extraction and stripping reactions are discussed.

Jan 1, 1972

According to the Balandin's (1) "multiplet theory of catalysis", adsorption can occur only if atoms of the reactant molecules are congruent with surface atoms of the catalyst. Such a condition calls for certain definite geometrical relationships between the reactant molecules and the atoms at the surface of the catalyst. If such a match or geometrical 'fit' is not provided, the surface reaction will not take place. An appropriate analogy to this may be the lock and key theory that enzymes should fit a substrate just as a key fits a lock. Similar geometrical considerations in adsorption studies were made in connection with the flotation of minerals. Gaudin(2) and Gaudin and Preller (3) proposed that if the dimensions of collector ions are in registry with the mineral lattice, an ordered layer of adsorbed species is formed. They explained that the structural fit is one reason for good flotation of galena with xanthate. In another study, Bachmann (4) attributed the selective flotation of KC1 from NaCl with amine to the fact that the lattice parameter of the amine collector is closer to that of KC1. Schubert(5) investigated the flotation of various nonmetallic minerals with amine and pyridine, and related the dimensions of the collector ions with the anion distances of the mineral surface. He concluded that good flotation is obtained when the tolerance is within 20%. The geometrical theory has also been used by Groszek (6) to explain the preferential adsorption of n-paraffin onto the basal plane of graphite. The geometrical theory has thus been found useful in explaining adsorptive properties of an adsorbate relative to the substrate structure. The purpose of the present work is to examine the possibilities of a geometrical fit between sodium dodecyl sulfate and Cu(OH)2 surface, and to construct a crystallographic model of the surface compound.

Jan 1, 1974

By Joseph A. Kantor

Several wall rock porphyry or pyrometascmatic copper deposits occur within the metamorphosed Paleozoic formations along the northern and eastern flanks of the Little Dragoon Mountains. Rocks ranging in age from Precambrian to Recent occur in the area. The Tertiary age Texas Canyon Quartz Monzonite intruded the sedimentary section in the eastern half of the range metamorphosing the Paleozoic carbonate units to tactites composed of garnet, diopside, and tremolite. Copper, zinc, and molybdenum minerals deposited in sites which are structurally controlled and stratigraphically favorable. Because the deposits are covered by alluvium, the information on structure, alteration, and mineralization is based upon a study of the diamond drilling programs. The mineralized district can be divided into four areas: 1) The Johnson Camp copper-zinc deposits; 2) The Dragoon copper deposit; 3) The I-10 copper-molybdenum deposit; 4) The Strong & Harris copper-zinc deposit. On the southwest end of the range beneath alluvial cover, the Cretaceous Bisbee Group was thrust over Precambrian and Paleozoic formations. The Tertiary Texas Canyon Quartz Monzonite intruded and metamorphosed them. In the upper plate, the Cretaceous sediments near the intrusive were metamorphosed to metaquartzite and andalusite and sillimanite schists. In the lower plate the Martin and Horquilla formations were marbleized. The lower Abrigo was metamorphosed to epidote rich calc-silicate tactites and biotite hornfels. A composite geologic cross section, based upon diamond drilling,, through the Dragoon copper deposit is shown in Fig. 1. The geologic events which formed this deposit are: 1. A faulted section of Precambrian Pioneer formation and diabase and Cambrian Bolsa and Abrigo formations was thrust over Pennsylvanian Horquilla formation. The Dripping Spring quartzite if present, has not

Jan 1, 1977

By D. R. Nagaraj

Depression of copper sulfides followed by MoS2 flotation is the most commonly practiced technique for Cu-MO separation. Although numerous organic depressants have been developed in the past, a majority of the currently used copper depressants are inorganic compounds (ex. NaHS, Nokes reagent, etc.). A unique advantage of organic depressants over the inorganic compounds is the potential versatility for design of the organic molecule to suit many requirements. The present study was initiated to systematically investigate the structure- activity relationships for a large number of organic complexing agents in comparison with the commonly used inorganic depressants that are often inefficient and hazardous. The results obtained in this study are discussed in light of the useful correlation obtained between practical solution redox potential and depressant activity. Several requirements, such as the presence of an active -SH and hydrophilic -OH or -COOH in the organic molecule, are identified for a reagent to be a satisfactory depressant. Some preliminary results on the desorbability (or destruction) of collector coating on the sulfide surfaces in the non-xanthate collector systems are also discussed.

Jan 1, 1983

By R. W. Smith

Though generally rather non-selective in nature long chain collectors nevertheless function in different ways in accordance with their own particular physical characteristics. Altering various parts of their structures such as chain length, type of chain, etc. can therefore substantially alter the adsorptive behavior of the collectors in a set environment. The effect of such structural differences of the collectors on physical parameters such as solubility, critical micelle concentration, acid or base strength, tendency to be expelled from the aqueous phase is discussed, as is also the effect of these parameters on flotation behavior.

Jan 1, 1989

By T. L. Heidrick

Late Cretaceous-early Tertiary Cordilleran porphyry Cu-Mo districts and their consanguineous Zn-Pb-Ag-Au-W vein and replacement deposits of the Rocky Mountain region comprise one of the largest, best studied, diverse, complex, puzzling, and richest compound metallogenic provinces on earth. A concise space-time definition of intermineral plate, regional and local structure-tectonic frameworks is crucial to deciphering their diachronous metallogeny and enhancing the explorationist's odds of future discovery.

Jan 1, 2013

By J. M. Applegate, C. L. Morgan

Introduction In the same way that a blueprint communicates informa¬tion about a structure, a systems architecture should provide information that guides the construction and implementation of a computing system. Taking the blueprint analogy a step further, a plot plan can also show where, in the "bigger picture," a particular design fits (if in fact it does) and what a builder needs to know about the environment in which he or she will operate. In the context of business systems, a meaningful architecture should convey the following: • the primary purpose of computer-based systems rela¬tive to particular tasks or operations, • the relationship of the systems to each other and an indication of their interaction and dependencies, • the relationship of the systems relative to the organiza¬tion and its objectives, • indications of where IS/IT resources can best be allo¬cated to support the organization and • the overall context in which new systems and technolo¬gies can be assessed for both their impacts on current systems and on the organization itself. In theory, a well-designed systems architecture should allow an organization to focus its resources on those aspects of its business that matter most, thus, leveraging investments in information technology to a competitive advantage. In addition, the way that a computing systems architecture is represented should be un¬derstandable to non-IT staff, and it should be eas¬ily recognized by the people it supports. This pa¬per attempts to show that a meaningful systems model exists and that its applica¬tion to mining can achieve the desired results. The following discus¬sion is based on the au¬thors interpretation of a concept referred to as the computer integrated manu¬acturing (CIM) model, as developed by Allen-Bradley. An inherent strength of the CIM approach is that the model combines aspects of business-reporting structures with the manufacturing process itself. What results is a systems frame¬work that is aligned with relevant business processes and is, therefore, easier for non-IS/IT personnel to interpret. The successful application of the CIM model can be seen in a large number of both discrete and process-manufacturing facilities throughout the United States. This paper provides a brief overview of the CIM model and then describes how the model can be applied at a conceptual level to the mining industry. Finally, this paper proposes an extension to the CIM model that the authors believe will make it easier to understand and apply. CIM model As shown on Fig. 1, the CIM model begins with the most detailed levels of process equipment and works its way up to the highest level of consolidated financial reporting. Systems at each level are characterized by common attributes, users, time frames, etc., providing a clear picture of their interac¬tion. Further analysis of the relationships between systems and between levels provides insight into the opportunities for integration. Regardless of the industry or processes involved, the CIM model provides a framework in which the characteristics of systems and the data they manage can be predicted based on the nature of the business function they support. In general, as data moves upward from the lower rungs of the CIM model, it changes from de¬scribing the physical na¬ture of a process to describ¬ing its financial aspects (e.g., from productivity to cost). The time frame to which data applies also transitions from a very short duration, perhaps only milliseconds, to financial or regulatory reporting time frames that may span years. In a simi¬

Jan 1, 2000

By C. West

Structured or embossed HDPE and LLDPE geomembranes have been available to mine owners and designers for over ten (10) years. As many owners and designers discover and demand the consistent high quality characteristics of this type of geomembrane due to the unique manufacturing process, the use of these materials in new mines, mine expansions and final closure designs has steadily increased. Structured liner materials are available for double lined and final cover systems and are revolutionizing the way ponds, pads and final closures are constructed. This paper will discuss the structured or embossed geomembrane concept and manufacturing process. Additionally, the paper will present comparative testing illustrating the major advantages of using this type of product in these types of applications. Both technical and economic advantages are illustrated. The cost savings include lower installation costs, less material used, and third party inspection times not to mention better performance. These new systems will be presented.

Jan 1, 2011

By Lim Thi Duong, Du Duy Bui, Thuat Ngoc Pham, Chuc Ngoc Pham, Que Anh Nguyen, Hoa Anh Bui, Chi Thi Ha Nguyen, Hoan Thanh Nguyen, Bac Quang Nguyen, Kien Trung Nguyen, Dung Trung Doan, Nhiem Ngoc Dao

The microstructures and kinetics of a rich iron ore ( TFe = 65.84%) of Na Rua mine, Vietnam, used for the iron production were investigated in this study. Thermal behaviors of iron ores were well-examined by heating microscopy, thermogravimetric analysis, and differential thermal analysis. After being pelletized and then oxidatively fired at 500–1200 °C for 2 h, the pellets fired at 1200 °C (P1200) displayed a hard and dense structure with a decent compressive strength of 317.9 kg/pellet whereas those fired at 500 °C (P500) had a soft and spongy structure. The reduction of iron pellets conducted in a flow of a 60–100% CO2/ Ar gas mixture at 900–1100 °C showed significantly higher efficiency than the reduction using coal. The spongy pellets showed superior performance for the reduction in the CO/Ar gas mixture compared to the dense ones, compatible with the production of sponge iron. When mixed with an amount of coal, P1200 designed for iron production in the blast furnace demonstrated an impressive reduction activity compared to P500 and previous studies. The kinetics of pellet reduction was determined by the diffusion of substances through the solid product layers having the mathematical model of 1 − 2 3 f − (1 − f )2∕3 = kt . The microstructures of pellets during the oxidative firing and reduction were also examined by X-ray diffractometry; scanning electronic microscopy; energy-dispersive X-ray spectroscopy; and Brunauer, Emmet, and Teller method.

Jun 7, 2022

By K. -A. Björkstedt

INTRODUCTION Strassa lies in the central part of Bergslagen, a tradi¬tional mining district, on the eastern side of the Stora Valley at an elevation of about 200 m above sea level. A railway siding runs between the mine and the Stora railway station from which there are railway connections to the shipping port and iron and steel works in Oxelosund, about 224 km away. The distance to the provin¬cial capital Orebro is about 60 km. The climate is typi¬cal for this part of central Sweden and is illustrated by the diagram of monthly precipitation and temperatures for the years 1968-1975 (Fig. 1). HISTORY There is no certain information as to when the Strassa mine was first worked, but it is known from sur¬viving accounts of mine inspectors that there were smelt¬ing works in operation in nearby villages in the 12th century. An example is the Gusselhytta ore smelting works, 10 km south of Strassa, which dates from this period. Around the year 1540 there were two smelting works in Strassa, the Upper Karberg and Lower Karberg works. Ore for these smelters was probably taken from Strassa and from the adjacent Blanka mine. In the year 1624 Strassa is mentioned by the painter Jons Nils Krook in an account of the iron mines in the Linde mining district (Linde Bergslags Jarngruvor). Several mines were listed in the area, the deepest being about 30 m. An impressive power installation is mentioned in 1639, including a piston system of lashed poles for transmit¬ting power from the Stora River to the Strassa fields. Its length was 2670 m. Common ground comprising about 20.2 km2 (5000 acres) of forest was allocated in 1689 for the furtherance of mining operations. Until the beginning of this century only the rich cen¬tral parts of the ore body were mined and these yielded, after handpicking, lump ore suitable for smelter feed. An example of the ore grades from these early times is an analysis of ore from the "Big Mine" (Storgruvan) from the year 1873: 48.5% Fe, 0.008% P, and 0.06% S. This same year a total of about 18 000 t was ex¬tracted from the Strassa mine. OWNERSHIP The mine was owned and run until 1874 by a min¬ing association made up of 119 so-called "bergsman," who were homesteaders often engaged in agriculture and timber-cutting as well. In that year the Strossa Grufvebolag (Mining Co.) was founded. In 1906 it was con¬verted into a joint stock company, the Strossa Gruveaktiebolag. This was acquired in 1907 by Metallurgiska AB for the implementation of Gustav Grondal's beneficiating and briquetting methods, for which the Strassa ore was well suited. The same year saw the completion of a new ore dressing plant with an annual production of 46 000 t of ore concentrate. In 1911 the mine passed to new hands, and in 1913 it was purchased by an Austrian company. Extensive new installations were made and in 1915 a new dressing and briquetting plant was completed with twice the capacity of the old one. In 1917 the Strassa mine was acquired by Granges. Be¬cause of unfavorable business trends and technical diffi¬culties, mining operations were brought to a close in 1923. Pumping kept the mine free of water until 1933 but it was completely filled ten years later. Up to 1950 the surface buildings and installations remained intact but the large dressing and briquetting plant burned to the ground in that year. Today only the machine shop re¬mains from this earlier period of operation, now housing parts of the Mineral Processing Laboratory. The decision to take up mining operations again was made in 1955 and construction work began the follow¬ing year. Of the old installation, only the "southern shaft" could be used for some development drifting after it had been completed with a new headframe. Other¬wise, all the buildings and installations required for the operations had to be rebuilt. New installations ready by 1960 were office and personnel facilities, a new shaft and headframe, a sorting and concentrating plant, a macadam plant, settling basins, pump stations, and a railway and yard with transport equipment. The instal¬lation was completed with two plants

Jan 1, 1982