Search Documents

By Paul F. Gnirk, Ralph A. Wagner, Joe L. Ratigan

This thermomechanical analysis used the finite element method to investigate the behavior of crushed salt backfill in a waste disposal room situated in a salt dome repository. The first of two objectives was to determine the transient temperature rise and degree of thermomechanical consolidation that occur in the backfill as a function of drillhole depths. The second objective involved the evaluation of closure due to salt creep of unlined emplacement drillholes and the determination of pressure on steel sleeve liners in the drillholes should liners become necessary for canister retrieval. The retrievability period was considered to extend for 25 years after waste emplacement. The canisters were assumed to contain ten-year old high level waste with a thermal output of 4.3 kW at the time of emplacement.

Jan 1, 1981

By W. C. Patrick

The Spent Fuel Test-Climax (SFT-C) was con- ducted to evaluate the feasibility of retrievable deep geologic storage of commercially generated spent nuclear-reactor fuel assemblies. One of the primary aspects of the test was to measure the thermomechanical response of the rock mass to the extensive heating of a large volume of rock. Instrumentation was emplaced to measure stress changes, relative motion of the rock mass, and tunnel closures during three year of heating from thermally decaying heat sources, followed by a six month cooldown period. The calculations reported here were performed using the best available input parameters, thermal and mechanical properties, and power levels which were directly measured or inferred from measurements made during the test. This report documents the results of these calculations and compares the results with selected measurements made during heating and cooling of the SFT-C.

Jan 1, 1986

A thermomechanistic model was developed for the thermal decomposition of the enargite contained in a copper concentrate at 650° to 750°C in a fluidized bed with an inert atmosphere. At the particle level, the model permits one to predict the thermal profile inside the reacting enargite particles, as well as their thermal cycle. At the macroscopic level, a population-based model coupled to the bubbling-bed fluidized bed model allows one to predict the fractional conversion (dearsenification) of an enargite-bearing copper concentrate.

Jan 1, 2002

By H. Wu, V. Izaxon

Intensive ventilation is required during the excavation of a mine opening and the subsequent exploitation of the mineral resources. The exchange of heat between the ventilation air and the rock mass has a major influence on the thermal regime of a mine, especially in the initial segment of the airway. In frozen ground, heat flow into the rock mass from the ventilation air can result in the eventual thawing of the permafrost, which can result in roof-rock instability. This paper presents a mathematical analysis of the dispersion process of ventilation-induced heat by thermosyphons placed on the surface of the mine. The principal uses of thermosyphons in the Arctic are to reduce the ground temperature to prevent potentially unstable permafrost from thawing and to increase the bearing strength of the material. The mathematical model of the physical problem, generally known as "the Stephan problem," takes into account the varying thermo-physical properties of air and the frozen and thawed rock mass, the thermal properties of the freeing fluid in the thermosyphons and the phase change of water. Finite-difference techniques were employed to determine the temperature isotherms around the thermosyphons. It was found that two rows of thermosyphons on a 10- x 10-m grid provide an acceptable design spacing for reducing the ground temperature around the mine airway.

Jan 1, 1997

By Boleslav Taraba, Antonín Taufer

Thermovision monitoring of surface temperature has been examined for the purpose of detection of spontaneous combustion of early stage. Measurements were carried out in bituminous and subbituminous coal mines. It was found that surface temperature heterogenities can be considered as common phenomenon in mine openings. However, the most of the observed temperature heterogenities were not connected with coal spontaneous combustion of early stage. These, so called [non-spontaneous combustion] temperature heterogenities in surface of mine openings were found to be caused by: l. Different conditions of heat transfer between opening surface and air stream; 2. Low temperature (natural) oxidation of coal; 3. Dissipated heat loses of working machine. Sites of early stage spontaneous combustion of coal were characterized by: 1. More significant, local rise in surface temperature comparing with low temperature coal oxidation; 2. Evolution of carbon monoxide with local concentration near the surface of such site more than about 15 ppm (bituminous coals) or 30 ppm (subbituminous coals). INTRODUCTION Mine fires are a serious hazard to life and result in a considerable loss of coal reserves. Thus, great attention is paid to investigation of new methods enabling already early detection of self-heating of coal. The earlier a fire is observed, the easier would it be to deal with. Detection methods used in coal mines are mainly based on: 1. [Mine air analysis]. Changes in composition of mine air are examined. Products of spontaneous heating of coal, not being present in mine air under normal conditions, are considered as indicators of anomalous behaviour of coal (carbon monoxide, unsaturated hydrocarbons) (Mackenzie-Wood and Strang, 1990). 2. [Temperature measurements]. Sites of higher temperature level comparing surroundings are looking for underground using various direct or indirect methods of temperature measurements. This paper summarizes experience from thermovision monitoring, as one of the latest indirect temperature measurement technique, used for the purpose of early detection of self-heating of coal in mine openings. INFRARED THERMOVISION Infrared thermovision device of AGEMA Infrared systems AB (Sweden) was used for the in situ measurements. The constant value of emissivity factor, 0.95, was pre-set as the most probable level of emissivities of coal and rocks in mine conditions.

Jan 1, 1993

By D. P. Patil, B. K. Parekh

Water is the mainstay for beneficiation of fine size coal and minerals; however, it is also the least desirable constituent in the final product. The basic concept of the novel process described in this paper is based on the differential surface heat conduction/ absorption capacity of individual particles, which differs for different species of minerals. When a mixture of fine material is exposed to a radiant energy source, the various solids present in the mixture will absorb heat energy depending on their heat-conducting properties and there will be a difference in the surface temperature of the particles. When this differentially heated solid mixture is placed on a moving belt, which is coated with a low temperature melting resin, the hotter component of the mixture will stick to the belt and relatively cooler particles will stay free on the belt and fall off at the end of the belt run. Experiments were conducted with pyrite, coal, and quartz of 6 × 18 mesh particle size. The goal of the test program was to find the optimum conditions at which there exists a required temperature difference between minerals and coal particles by controlling the operating system variables. Preliminary tests results showed that there is a potential for separating mineral matter from coal using the thermo-adhesive separation technique.

Jan 6, 2022

By I. M. Eitani, M. Karmis

Ground control presents the most serious problem in underground thick seam mining. In addition to parameters such as depth thickness and inclination of the seam and nature of the coal and the immediate strata, the stress interactions caused by the mining sequence must be carefully evaluated and understood, if safety and productivity objectives are to be fulfilled. In this paper, the most widely-accepted thick seam coal mining methods are reviewed and suggestions are made for future work pertaining to ground control problems.

Jan 1, 1981

By J. B. Gwiazda

Introduction Thick seams constitute a considerable portion of Polish coal reserves. In producing mines and those under construction, the reserves where the height is more than 4.5 m (15 ft) total about 24v0 of all the hard coal reserves. The reserves that are under urban and industrial areas can be extracted using stowing methods for surface protection. About 50v0 of thick seam reserves can be extracted by caving methods. Thick seam mining methods Thick seams are usually extracted by multilift methods. There are some methods of thick seam mining that generally can be divided into caving and stowing methods. The stowing method is more expensive, but must be used when mining to protect surface features. The more known methods of thick seam mining include: • extraction of thick seam in ascending order with stowing; • thick seam mining in descending order with consolidated stowing; • thick seam mining with gob consolidation; • thick seam mining in descending order with roof caving; • sublevel caving thick seam mining system; and • thick seam mining system using an artificial roof. • Thick seam mining with introduction of an artificial roof The most advantageous method of thick seam mining is the method using an artificial roof. The artificial roof usually consists of wire mesh. Such wire mesh must be durable and must prevent small rock fragments from passing through. The mesh is usually made of steel properly protected against corrosion. The artificial roof is placed on the coal floor of the top slice (Fig. 1). Caving rock falls on the artificial roof and is thus separated from the coal. The next slice is extracted under the artificial roof. The producing face of the next slice must progress within 10 m (33 ft) behind the front of the first slice. As the second producing face progresses, the wire mesh moves down on the coal floor and may be used as an artificial roof for the next slice. Thus, one artificial roof allows the extraction of several consecutive slices. Application of the artificial roof allows for clean extraction and reduces coal losses. It also eliminates the hazard of spontaneous combustion. Introduction of the artificial roof has been limited due to a lack of artificial roof laying equipment. Manual laying of wire mesh is a labor-intensive operation, and it delays face progress, resulting in poor productivity. To eliminate these problems, artificial roof laying equipment was designed at the Polish Central Mining Institute. The support and the method of laying operation is covered by a patent. Artificial roof laying powered support To extract thick seams using an artificial roof; four-leg shield supports with lemniscate linkage were developed (Fig. 2). This shield is used in the first top

Jan 1, 1988

By James M. Johnson, David Landriault, Frank Palkovits

The term “Paste Technology” was first used in the late 1980’s. It was used to describe a high fines (15 wt% or greater minus 20 microns), low water content backfill material that could be transported underground through a borehole/pipeline distribution system (4” to 8” dia.) at a yield stress similar to fresh concrete (100 to 400 centipoise). This “Paste Backfill”, unlike slurry transported backfills does not segregate into separate solid and liquid phases at low pipeline transport velocities or upon disposal into the underground stope. Paste backfills can consist solely of fine material, or can include fines plus sand and aggregate similar to a concrete mix. Pipeline transport of paste requires that sufficient fine material (minus 20 micron content) is contained within the mix to lubricate the pipeline walls to create a plug flow condition. For concrete, the fine material is supplied through the cement addition to achieve high compressive strength. For paste, the fine material is generally available in large quantities in the form of mill tailings. The paste tailings can be transported underground for use as backfill or discharged on the surface in a tailings management facility (TMF). This natural abundance of fine grained material is not exclusive to mine tailings but is common to many waste streams in many different industries. This makes the disposal of many waste materials very amenable to paste pipeline transport and placement as a non-segregating slurry. The potential use of paste technology for a wider group of waste materials was realized by these authors and others over two decades ago. Through the effort of this small group the use of paste technology has expanded over the years to become recognized as a low cost, environmentally superior, and technologically controllable method of transporting and placing specific material waste streams with a low water content and high placement density. The high yield stress nature of a paste also lends itself well to the blending of one or more coarse waste materials into the fine waste material paste stream. This allows all the waste materials to be transported by pipeline, increases their placement density; decreases the supernatant release/treatment, reduces contaminant mobilization, hydraulic conductivity and oxygen/water reactivity through encapsulation in the paste matrix. The following paper describes the present state-of-the-art use of paste technology in the world today. It also describes future uses of the technology that are under development and speculates on the overall use of the technology for waste management in the future.

Jan 1, 2005

By T. Wisdom, D. Romo, G. Seale, R. Jansen

Thickening remains relatively misunderstood since it is typically near the end of the process and not directly involved in metal recovery. When operating well, thickeners are ignored and left to run independently, the ‘out of sight, out of mind’ phenomena. However, when operating poorly, there is a lack of basic understanding and remedial actions to solve issues are reactionary rather than proactively addressing shortcomings. This series of papers breaks down in sequential order the stepped phases required to gain an appreciation and thorough understanding of the science behind thickeners, and key thickener components, and basic troubleshooting skills. This second paper starts with identifying the different approaches to thickener test work including static and dynamic settling tests followed by high-rate versus paste thickening. Complimentary to test work, the mechanisms surrounding coagulation and flocculation are presented and explained. The basic mechanisms for coagulation and flocculation are discussed to support the different test work approaches and provide the reader with the basic background.

Mar 2, 2022

By R. J. Smith

Hornestake's Mclaughlin Mine is the first commercial application of pressure oxidation pretreatment of gold prior to cyanidation. Inherent to the autoclave process are several liquid/solid separations. Flocculant consumption represents a significant portion of the consumable reagent costs at McLaughlan. This paper focuses on the efforts of the Operating, Metallurgy and Engineering groups to improve thickener operation and minimize flocculant consumption. An operating philosophy incorporating feed solids control, increasing flocculant dilution water and minimizing flocculant solution shear has resulted in a reduction in 1986 flocculant costs of $0.054/t ($0.06 st) versus 1985 costs. Additional changes are projected to result in a further cost reduction of $0.20/t ($0.22/.st) in 1987.

Jan 1, 1988

By Thomas W. Healy, David V. Boger, Yee-Kwong Leong, Lee R. White, Peter J. Scales

The concentration of mineral slurries by conventional thickening devices is discussed. The role of additives on the compression of mineral slurries is also examined. Results for a range of flocculation conditions are presented. The compression of flocculated mineral slurries is found to be highly dependent on the fundamental particle-particle interaction forces and hence, the rheology of the particulate fluid. It is demonstrated that a detailed knowledge of the properties of both the mode of operation of the thickening device and of the solid/liquid interface is required for improvement in the rate and in particular, the extent of dewatering.

Jan 1, 1995

By H. Hamza

Oil sand tailings are disposed of in large ponds in which MFT (Mature Fine Tailings, a stable suspension of fine particles in water) forms after many years of settling. Long-term storage of large volumes of MFT is costly to maintain and also poses an environmental liability. The Advanced Separation Technologies laboratory at CANMET Western Research Centre has worked closely with oil sand companies to eliminate MFT generation by applying paste technology to oil sand tailings. In this process the fine tailings are flocculated to produce a thickened material that has the potential to consolidate to a dry landscape, while warm water is recovered and recycled for reuse in the extraction process. This paper presents some results of an extensive technical program involving bench-scale tests for flocculant selection and continuous thickener pilot tests.

Jan 1, 2002

By E. B. Fitch, D. A. Dahlstrom

Liquid-solids separation is common to practically all mineral and coal processing as the bulk of beneficiation plants employ water as the major processing vehicle. The growing usage of hydrometallurgy has increased the importance of liquid-solid separation as acidic and basic solutions result in greater amounts of colloidal solids, with their consequent greater difficulty of separation, the economic need for chemical recovery to minimize this operating cost, and the usual necessity of employing more costly construction materials. The three processing steps covered in this section have significant capital costs. Drying, particularly, has an important operating cost because of the obvious need for energy to evaporate the water or solvent. Several common factors influence all three liquid-solid separation steps. Particle Size and Size Distribution. In general, finer particles have slower settling and filtration rates. The specific surface area is increased, which means a lower solids concentration in the thickener underflow and discharged filter cake as well as a grater moisture content to be evaporated in the drying step. Therefore, overgrinding or excessive attrition should be avoided. Consideration should be given to optimum particle size consistent with entire plant operation performance and recovery. Solids Concentration. Increased feed solids concentration will generally minimize required equipment size and costs in all three liquid-solid separation steps. Most thickeners are designed on the basis of unit area required, expressed as square feet per short ton of dry solids per day (square meters per metric ton per day) which will usually decrease with increased feed solids concentration. Filtration rates also increase as the required flow through the capillaries of the filter cake decreases. Dryer capacity increases and less energy per ton of final product is required to evaporate the associated moisture. Particle Shape and Surface Characteristics. Generally, optimum shape is a spherical particle of zero porosity. As either of these factors degrade away from the desired state, difficulty increases. This is particularly true in drying, where porosity can decrease drying rate significantly if the moisture must first reach the particle surface by diffusion

Jan 1, 1985

By Edward M. Jacobs

In some ore grinding circuits it is desirable to make separations purely on size. The normal choice for this is vibrating screen equipment. Developments in screening process technology have led to improvements in the capacity and efficiency of vibrating screens, through the adoption "Thin Layer Wet Screening". This process can reduce recirculating loads and equipment requirements in the ore grinding circuit.

Jan 1, 1985

By R. B. Dunn

Whilst coalmining in the United Kingdom has been synonymous with longwall mining practice there have been changes in recent times which have enabled not only an extension in the length of the face to be worked but also in the ability to extract both thick and thinner seams. Additionally the industry has taken a positive view in the extension of retreat methods of extraction applied for different reasons both to particularly thick and specially thin seams. To permit development of a flexible programme to meet these diverse needs, it has been necessary to design machinery along with mining systems specially suited to these requirements. In reviewing current UK thinking special emphasis is made on the extraction of thinner seams generally of higher quality coal at moderate depths with a commentary on some recent results.

Jan 1, 1979

By Michel L. Van Sint Jan, Gabriel Fernandez-Delgado, Edward J. Cording, James W. Mahar

INTRODUCTION Shotcrete behavior observed in subway tunnel construction in the U. S. has been primarily in blocky or blocky and seamy rock in which rock loads develop from the self weight of individual rock blocks that tend to loosen from the wall and roof of the opening. Such conditions can be classed as loosening ground, in contrast to squeezing ground in which high pressures are generated on the tunnel lining with time as the ground creeps under the natural ground stresses. In the philosophy often associated with the New Austrian Tunneling method, emphasis is placed on the use of shotcrete and other support elements in squeezing, highly stressed ground, in which the support system is designed to allow controlled movements so that high lining stresses do not develop. In contrast to these conditions, the concern in loosening ground is to provide support soon enough to minimize loosen-

Jan 1, 1979

By John Marsden, John Mansanti, Jim Arnold, Mike Gleason

DOUG HALBE: We're not quite to the end of our session, but we're close. We've had a lot of fun with some of these spill ideas. But these are serious problems, and I think we might be able to benefit by continuing to compile these. Several years ago, the metallurgists at the various operations of Gold Fields Mining Company had a newsletter that came out every two months for several years. This publication consisted of short articles by the staff at the various operations, plus a few others, on problems they'd had and how they solved them. One very useful article, "Things We'd Have Done Differently at Chimney Creek," was written shortly after start-up. John Marsden was the editor and John Mansanti contributed to it, as did Jim Arnold (our distinguished co-chair) and Mike Gleason. I would be interested, with the permission of the audience, in editing that article to make it a little bit less abrasive and putting it into the record here. I think it's a useful SME function to maintain a list of things we've done wrong in plant design, things we don't want to do again. If we have another open session in the future, would others be willing, even anonymously, to contribute, bring slides, and say "Hey, look at the goofs we made?" [laughter, followed by support from the audience] Okay, we'll plan on that. And we'll try to include the Chimney Creek list in the transcript of this session-perhaps edited a bit.

Jan 1, 1998

By B. Anderson, P. Churak, S. Dewar, A. Johnson, P. Eger

Although vegetation can be successfully established on fine taconite tailings, innovative approaches are needed to reclaim the coarse tailings used for dam construction. Through a series of cooperative projects with various government agencies and industries, EVTAC has been able to develop a unique closure plan. This plan will not only meet current reclamation standards, but also provide mitigation for a disturbed wetland and possibly create a tree plantation in the interior of the basin. By using waste products and exchanging materials, reclamation of the entire basin will be accomplised in a cost effective manner.

Jan 1, 2002

By P. K. Sharma

The acidophilic and chemolithotrophic Thiobacillus ferrooxidans bacteria grown in the presence of soluble ferrous ions and solid substrates (sulfur, pyrite and chalcopyrite) as their energy source have been used in the investigations. The cell surfaces are characterised by zeta-potential, contact angle, FT-IR and FT-Raman studies. The adsorption isotherms of the cells on pyrite and chalcopyrite indicate that the adsorption begins on pyrite at a much lower equilibrium cell population than on chalcopyrite. The isotherms tend to level off at a cell adsorption density corresponding to a horizontal monolayer coverage when the geometrical dimensions of the cells are considered. In the presence of cells, the xanthate flotation of pyrite completely depressed, whereas chalcopyrite flotation is unaffected. The results suggest that chalcopyrite can be selectively floated from pyrite, also at a neutral pH region, in the presence of T. ferrooxidans cells.

Jan 1, 1999