Search Documents

By Walter Kahn

Increasing consideration is being given to simplifying traditional methods of tracing pipelines and maintaining required temperatures of stored fluids. Because of their reduction in capital costs, virtual elimination of maintenance. ease of control and "cleanliness"; interest in electrical techniques has accelerated. 1,2 Resistance cable and other heaters have been given some attention. but less well known in the recent introduction of thermal conductive coatings. This paper is addressed to the use of thermal conductive coatings for heating fluid-transport piping and storage tanks. Emphasis will be given to the simplicity, efficiency, and versatility of design and application which their unique properties further contribute to the general economics of electrical heating.

Jan 1, 1965

By Dwight K. Smith

Fly ash as an additive for oil well cement was introduced to the oil industry by the Halliburton Company in 1949. Since its early usage in the Illinois area of the U. S., the total amount of fly ash pumped into wells has exceeded 30 million sacks, The advantages of using fly ash-portland cement mixtures in wells are fundamentally the same as for concrete except the conditions of placement and curing are variable and the nomenclature of properties are expressed somewhat differently. In some instances deep wells have been cemented with mixtures of fly ash and hydrated lime together with an activator which functions as a catalyst for setting. This fly ash-lime formula has many advantages for high temperature-pressure conditions found in wells.

Jan 1, 1968

By Joel L. Morrison

Wet bituminous coal fines from active and abandoned slurry impoundments are currently being examined as a recoverable feedstock for the production of coal water slurry fuel (CWSF). Preliminary analysis indicates that these coal fines can be converted into low solids, low viscosity CWSF with acceptable stability without the use of viscosity modifiers (dispersants) or stabilizers. Efforts are now underway to determine if the impounded coal fines can be economically cleaned by froth flotation to an ash level of < 12 wt. % and a total sulfur content of 1.2 wt. %.

Jan 1, 1995

By I. Gombköto, G. Földing, G. Mucsi, B. Csoke, J. Faitli, B. Kovács

This paper summarizes the main achievements of our previous project entitled "Development of a technological system producing quality guaranteed fly-ash based binder". Furthermore, this study deals with the laboratory experience of lignite fly ash utilization for two different goals. On the one hand the fly ash was tested as a binder; on the other hand it was investigated as an underground mine backfill material. Considering the first goal, the utilization of a mixture of mechanically activated fly ash and lime for producing an independent binding composition has been assessed involving determination of relationship between the degree of activation of fly ash and the strength of the obtained concrete. The results confirmed that this hydraulic binder is suitable for construction of stabilization and capping layers or base layer. Regarding the backfilling application, this paper presents laboratory experiments, their results including settling tests, hydraulic permeability and strength measurements and dense slurry technology related results.

Jan 1, 2011

By Huiqin Yao, Dongmei Liu

The study investigated the potential use of low activity circulating fluidized bed combustion (CFBC) ash and phosphate tailings for the production of a filling material based on the cement. The phosphate tailings were used as aggregate and consolidated by cement and CFBC ash. The results showed that the bleeding rate and fluidity of all mixtures decreased with the increasing the amount of CFBC ash. The fluidity of filling slurry is highly related to the experimental factors such as the content of sulfur solid ash, B/A ratio, and mass concentration. The replacement of CFBC ash ranging from 20 to 40% led to a significant decrease in setting time and an obvious increase in compressive strength, but the above effect was obviously weakened when reducing the mass concentration and B/A ratio. The hydrated calcium silicate gel and ettringite generated from the hydration of cement and CFBC ash were the main sources of strength for the filling materials. When the recommended proportion was 1/6 binder/phosphorus tailings ratio, 76% solid content, and 40% CFBC ash replacement, the filling material still met demands on working and mechanical properties; at the same time, the utilization of CFBC ash and phosphorus tailings was maximized.

Oct 11, 2021

By G. Petrakis

The selection of suitable species of plants for the rehabilitation of mining disturbed lands is one of the most crucial decisions to be made concerning the success of planting revegetation. Native plant species are best suited for use in the work of reintroducing vegetation in rehabilitated areas. By using such species an increase in the success rate of rehabilitation is attained not only as regards yield due to their better growth ability (they are adapted to local climatic conditions), but also because of a better adjustment to and better visual harmonization with the surrounding unspoiled areas.

Jan 1, 2002

By Edward L. Vickers

When I was originally asked to give this talk, I had certain preconceived ideas of the mining industry&apos;s reaction to Operations Research. It seemed at the time to be a rather simple task to collect these ideas for presentation here today. Jotting down these notions, I became concerned that overexposure to this activity called OR perhaps had clouded my outlook on what was actually being done on a nation-wide scale. I felt, to have a better cross section, a questionnaire of current industrial activity was in order. I solicited the response of some 75 mining companies varying in sizes and operating characteristics, and I am pleased to report that the response was good. I received answers from 51. The questionnaire was intended to measure the degree to which their concerns were actually engaged in OR efforts. With all due respect to the people who were so gracious as to answer the questionnaire, I feel that there is a tremendous misconception as to the designed purpose of OR. This is not to imply that there are no active OR groups in the mining industry. But by in large, the majority of the companies sampled appear to be somewhat confused as to what OR really is.

Jan 1, 1962

By S. Shrivastava, R. G. Reddy

Spent potliner is generated in the electrolytic process of reducing alumina to make aluminum metal using molten fluoride electrolytes. Spent potliner (SPL), obtained at the end of the pots life contains a small amount of cyanide and fluoride which present environmental problems. SPL became a listed hazardous waste under RCRA (KO88) in July, 1990. One of the possible uses of spent potliner is as a substitute for Calcium Fluoride (CaF2) as a fluidizer in iron- and steelmaking and in the glass industry. A low viscosity and a low melting point are prime requirements for accomplishing the above. In the present study, viscosity measurements were performed. Effect of various additives, such as sand, limestone, dicalcium silicate dust, and MgO baghouse dust on the viscosity of SPL was studied. The results showed that with the addition of sand and limestone, very high fluidity of SPL melt can be obtained at significantly low temperatures. The results suggest that spent potliner mixed with additives could potentially be used as a substitute fluidizer.

Jan 1, 1999

By R. G. Reddy

Spent potliner is generated in the electrolytic process of reducing alumina to make aluminum metal using molten fluoride electrolytes. Spent potliner (SPL), obtained at the end of the pots life contains a small amount of cyanide and fluoride which present environmental problems. SPL became a listed hazardous waste under RCRA (K088) in July, 1990. One of the possible uses of spent potliner is as a substitute for Calcium Fluoride (CaF2) as a fluidizer in iron-and steel making and in the glass industry. A low viscosity and a low melting point are prime requirements for accomplishing the above. In the present study, viscosity measurements were performed. Effect of various additives, such as sand, limestone, dicalcium silicate dust, and MgO baghouse dust on the viscosity of SPL was studied. The results showed that with the addition of sand and limestone, very high fluidity of SPL melt can be obtained at significantly low temperatures. The results suggest that spent potliner mixed with additives could potentially be used as a substitute fluidizer.

Jan 1, 1999

By R. G. Reddy

Spent potliner is generated in the electrolytic process of reducing alumina to make aluminum metal using molten fluoride electrolytes. Spent potliner (SPL), obtained at the end of the pots life contains a small amount of cyanide and fluoride which present environmental problems. SPL became a listed hazardous waste under RCRA (K088) in July, 1990. One of the possible uses of spent potliner is as a substitute for Calcium Fluoride (CaF2) as a fluidizer in iron-and steel making and in the glass industry. A low viscosity and a low melting point are prime requirements for accomplishing the above. In the present study, viscosity measurements were performed. Effect of various additives, such as sand, limestone, dicalcium silicate dust, and MgO baghouse dust on the viscosity of SPL was studied. The results showed that with the addition of sand and limestone, very high fluidity of SPL melt can be obtained at significantly low temperatures. The results suggest that spent potliner mixed with additives could potentially be used as a substitute fluidizer.

Jan 1, 1999

By J. Armstrong, J. Bourgeois, S. Warren

The application of statistical analysis software programs has proven useful for investigation of rockfall runout distance along a designed slope. Rockfall modeling programs are continually being upgraded with more sophisticated analysis tools, such as the use of the rigid body versus lump mass models. Engineers at mine sites utilizing the software may have varied experience related to these models, their associated input parameters, and how to interpret the generated results. To address this concern, researchers at the Spokane Mining Research Division (SMRD) of the U.S. National Institute for Occupational Safety and Health (NIOSH) investigated the influence of slope height, slope angle, slope material, and rock size for both rigid body and lump mass models in a 2-D statistical analysis program. Based on a literature search and industry input, specific ranges common to that of an open pit mining environment were chosen for each of the input parameters to determine 90% rock runout distance as well as their sensitivity to change. Data collected from this numerical analysis and simulation will be compared to empirical rockfall data gathered through the duration of the Highwall Safety project conducted by NIOSH from 2022–2026.

Mar 2, 2022

By Jorge Armstrong, Sean Warren, JOSEF BOURGEOIS

The paper investigates the influence of slope height, slope angle, slope material, and rock size on rockfall runout distance in openpit mines. Using statistical analysis and simulation, the study aims to improve rockfall hazard assessment and catch bench design by identifying key variables affecting rockfall behavior.

Oct 1, 2023

By Brad Murray

Evaluating the performance of a shielded tunnel boring machine (TBM) can be difficult because the ground cannot be observed directly and in relation to the TBM attitude within the excavation. It is difficult to determine whether performance problems are caused by ground loading, steering issues, fine muck packing against the shield, or migration of annular grout around the shield. The Arrowhead Tunnels Project in Southern California uses strain gauges on its shielded hard rock TBMs to detect shield strains early and correlate them with tunneling conditions, thereby increasing the chances that problems will be correctly diagnosed and addressed to optimize TBM performance. The frequent automatic measurement of shield strain has also been valuable by confirming whether remedial methods used to free the machine after stoppages are effective. This paper discusses the qualitative interpretation of characteristic strain patterns on the Arrowhead Tunnels TBM shields and discusses installation details and special considerations for setting up a strain measurement system.

Jan 1, 2008

By Joel K. Witt, Jackson G. Jenkins, Wendy M. Gort, Brent A. Whitman

A major concern for operators of leaching/SX-EW plants is a phenomenon known as gunk or crud. The build up of gunk is typically the result of fine particulates which are transported via the leach operation to the solvent extraction plant. The particulates develop into a solid layer that concentrates at the aqueous/organic interface. This can cause phase separation problems which can result in entrainment and other deleterious operating conditions. Most operations physically remove the gunk from the SX settlers and process it via a centrifuge or coalescer to remove valuable organic. While both methods have served for many years, Magma is currently evaluating the use of a chemical surfactant which induces a definitive separation of particulates from organic.

Jan 1, 1994

By G. Triantafillou

The aim of this paper is to present the progress of the plan of the Greek Public Power Corporation S.A. (PPC S.A.) at the Lignite Centre of Megalopolis in Peloponnesus (southern Greece) to manage impacts on local communities in areas affected by its activities during the lignite mining operation and post-closure. The reclamation works in the waste dump areas of the mines that constitute the Megalopolis Lignite Centre, concerning the utilization of waste dumps for infrastructure community projects constructions are discussed. Moreover, selected environmental indicators concerning land use and closure and rehabilitation are presented.

Jan 1, 2008

By Alan H. Goode

Of the 15 million tons of glass discarded in municipal wastes annually, about 2 million tons pass through incinerators and can be recovered by ore processing techniques. Although the primary use for this recovered waste glass would be as cullet in the manufacture of new glass containers, this approach is not always practical because of long shipping distances, high freight costs, and high purity requirements. Alternatives to the use of waste glass as cullet would be either as landfill or in secondary products. Although glass is considered a good landfill material, it is still wasteful of potentially valuable raw materials. Secondary products that can be made from waste glass1 include a variety of industrial and construction items. As part of the Bureau of Mines&apos; program in secondary materials recovery, the Tuscaloosa Metallurgy Research Laboratory has conducted research concerned with the development of ceramic building products from waste glass. Materials employed in this research were obtained from municipal incinerator residues fractionated in the Bureau&apos;s continuous residue processing plant, College Park Metallurgy Research center.&apos; The studies reported herein3,4 present research results using waste glass in the formulation and production of clay bricks, not only to produce improved products, but to reduce production costs, conserve natural raw materials, and most important, to reduce manufacturing energy requirements.

Jan 1, 1974

By J. C. Ashby

Electric utility response to certain amendments of the Clean Air Act has resulted in a production of several types of alkaline coal combustion byproducts. Alkaline combustion byproducts are gaining increasing usage for acid mine drainage mitigation as research leads to a better understanding of their beneficial applications. Since January of 1997, Mettiki Coal Corporation has been injecting alkaline flue gas desulfurization material from Virginia Power&apos;s Mt. Storm Unit #3 wet limestone scrubber into abandoned portions of the active Mettiki mine. This paper provides an overview of the key design, transportation, regulatory, and environmental issues faced in the project.

Jan 1, 1998

By Connor Meinke, Shaihroz Khan, Kevin Erwin, Rajiv Chandramohan, Muhammad Usman Siddiqui

High-quality sample selection for metallurgical test work is essential to a geometallurgy study, but the large multidimensional dataset makes sample selection a daunting task, as classifying the dataset while respecting its heterogeneity is difficult. This paper presents a streamlined approach for sample selection, utilizing custom-built tools in Python to standardize the methodology, saving time and costs. This approach uses the cumulative sum method, principal component analysis, and k-means clustering method to elegantly cluster the data and select representative samples. A case study is used to demonstrate the effectiveness of the methodology by selecting 40 samples for flotation test work.

Feb 1, 2024

By Jiang Su, Alan Bloodworth

"Composite sprayed concrete lining (SCL), consisting of two layers of permanent sprayed concrete separated by a layer of spray-applied waterproofing membrane, represents the latest development in SCL tunneling, but presents several challenges to designers. This paper aims to address the following issues: (1) how to simulate composite action, (2) behavior of a composite SCL tunnel, and (3) how to utilize composite action to achieve lining thickness efficiency. It firstly sets out the background to the composite SCL concept, and then presents a strategy for numerical investigation. The main part of the paper is the presentation and discussion of the simulation results, focusing on the lining deformation, load sharing and the safety margin of both linings. Interface stresses are also examined. It is found that significant secondary lining thickness reduction may be achieved by utilizing composite action. Challenges for the design of composite SCL tunnels are briefly discussed at the end. INTRODUCTION Sprayed concrete lined (SCL) tunnelling has seen rapid development over the last twenty years in the UK (Su 2013). One of these developments has been the replacement of traditional sheet membrane and cast in situ secondary lining with innovative spray applied waterproofing membrane and sprayed secondary lining system, which has been adopted in recent major projects, such as Crossrail (Pickett 2013), and brings many benefits to the construction (Dimmock et al. 2013). The combination of sprayed primary lining, spray applied waterproofing membrane and sprayed secondary lining is perceived to provide a structurally efficient lining system that outperforms the traditional lining system, which consists of sacrificial primary lining, sheet waterproofing membrane and cast in situ secondary lining. The claimed benefits in structural performance arises from the composite action between the sprayed primary and secondary linings via the spray applied waterproofing membrane, which produces a much stiffer cross-section and therefore a more efficient use of materials. Early investigations on the design of composite SCL tunnels were carried out without (1) definite and reliable long-term interface parameters, (2) a verified numerical modelling technique, or (3) consideration of different stress histories between primary and secondary linings (Thomas and Pickett 2011, Marcher et al. 2011). This paper reports the findings from a numerical parametric study on a typical composite SCL tunnel with varied secondary lining thickness. The results show that the true benefit of composite lining arises from the optimisation of the lining thickness (stiffness) ratio between the primary and secondary linings to achieve secondary lining safety and thickness efficiency at the same time."

Jan 1, 2016

By M. A. Georgiana

The Emerald Mine No. 1, located in southwestern Pennsylvania is presently owned and operated by Cyprus Minerals of Englewood, Colorado. High volatile bituminous coal is produced from the Pittsburgh No. 8 seam by both longwall and continuous mining methods. The coal is then mechanically cleaned on site utilizing a combination of heavy media separation and froth flotation methods prior to shipment to both the metallurgical and steam coal markets. The Emerald Mine is presently producing 2.8 million raw tons per year, while liberating approximately 6.5 million ft per day of methane. In light of the methane liberation rate, ventilation requirements have been significant and have always received utmost priority and consideration. Figure 1 shows the locations of the current and proposed shafts. Emerald utilizes two Joy (Model M120-58-880) axial vane fans on shafts No. 1, No. 2R, No. 3R. (one operational, one stand-by) The use of computer simulation of various ventilation networks was initially employed during the design stages (1975-1977) and has been utilized through the present. Obviously, the initial planning, under the ownership of Lykes Resources, was strictly theoretical. All the quantities were proposed and the resistances were based on prior simulations of other mines and mathematical formulas. However, once the mine was moderately developed, actual values were recorded and utilized. This procedure consists of: a) layout pressure and quantity points b) measure all air quantities where an air course splits

Jan 1, 1986