Search Documents

By P. B. Marchant

Bioleach testing and piloting was conducted on refractory gold sulphide concentrate from Austin Gold Venture in Nevada during 1988. The objective of the test programme was to determine the technical and commercial viability of bioleaching as a concentrate pretreatment step prior to gold extraction by cyanidation as an alternative to shipping concentrate to the smelter. Baseline CIL cyanidation typically resulted in < 20% gold extraction from the Austin concentrate. Bioleaching enhanced gold extraction up to 95% using conventional CIL techniques. This paper summarizes the bioleach test programme and results, including pilot plant studies onsite, and describes aspects of the commercial design for a possible retrofit of the Austin flotation tailings leach circuit to accommodate 20 tpd and 40 tpd capacity concentrate bioleach facilities.

Jan 1, 1989

By A. E. Torma

The efficiency of Thiobacillus ferrooxidans in the desulfurization of a high-sulfur content New Mexico coal was demonstrated. The optimum condition of process variables were found to be pH = 2.3, particle size = 38 µm, pulp density 14.1% (W/V) and temperature 33.9°C. Larger scale experiments carried out with these optimum conditions resulted in coal desulfurizations above 97%, while in sterile controls this was only about 10%.- The rate of desulfurization was described with an exponential expression with respect to the effects of coal particle size. The effect of pulp density on coal desulfurization was quantified by a Monod type equation. The apparent activation and deactivation energies, the frequency factor and temperature coefficient were derived from the effects of temperature to be ?aE - 11720 cal mol-1 and A = 30.44 mol dm-3s-lin the range of 20 - 35°C; ?Ed = 43930 cal mol-1 and A = 9.82 x 10-39 mol dm-3s-1 in the range of 35 - 45°C; and Q10 = 1.94 in the range of 20 - 30°C. The thermodynamic values [(?G+, ?H+ and ?S+)] of the activated complex were calculated. The generalized second order regression equation relating the degree of biodesulfurization of coal to the leach parameters was shown to adequately predict coal desulfurization within the range of process variables studied.

Jan 1, 1987

By Qiu Rongqing, Huang Kongxuan

This paper summarizes the results of treating arsenic­bearing refractory gold concentrates from six gold Mines of Chi­na by using bioleaching method and discusses the conditions of bioleaching processes. Results indicate that Thiobacillus fer­rooxidans T-3 Strain can intensely oxidize arsenopyrite, how­ever oxidation rate and degree differe considerably for different. During initial inoculation of 5 X 106 cell/ml. FeH contration generaly 4 -8 g/1. Sample size > 80 % - 3 20 mesh and pulp density 10 % ( w /v) and leaching time ,1 -- G clays, arsenic re­moval rate reached more than 80 % , Fe extraction ,10 - GO% desulfurization rate 30-45% after bacterial oxidation of 4-G days.

Jan 1, 1992

By E. Lee

The behavior of As bioleaching using Acidithiobacillus thiooxidans (A. thiooxidans) in mine tailings containing highly concentrated As contents (i.e., As=33877 mg/kg) was systematically evaluated according to the changes in temperature (25?40°C, pulp density=0.5%, pH=1.8), pulp density (0.5?4%, temp=30°C, pH=1.8), and initial pH(1.8?2.2, temp=30°C, pulp density=0.5%). The changes in temperature and pulp density affected the As leaching behavior more than the change in initial pH did. Based on the pH and oxidation-reduction potential (ORP) results, the As leaching was attributed to solution acidification. In particular, As leaching was accelerated with increasing sulfate production in the reacting solution. After bioleaching, surface of tailings examined that many pores which dissolved As were formed by a chemical reaction due to bacteria. The As bioleaching efficiency by A. thiooxidans was enhanced by the oxidation of both the added elemental sulfur and the sulfur compounds in the mine tailings. The As bioleaching efficiency was maximized at 50.5% under conditions of an initial pH of 2.2, reaction temperature of 30°C, and pulp density of 0.5%.

Feb 23, 2014

By Y. Lv, H. Ye, D. Du

Electrolytic manganese residue (EMR) is a kind of industrial solid waste with high silicon content that contains harmful metal elements such as chromium (Cr), copper (Cu), lead (Pb), cadmium (Cd), nickel (Ni) and cobalt (Co). Developing a highly effective and environmentally friendly process to treat EMR is important, both for the reutilization of metal resources and for environmental sustainability. In this study, the bioleaching of available silicon from EMR using silicate bacteria is investigated, with flask experiments conducted to optimize the parameters in the bioleaching system. For metal ions, the concentrations of manganese (Mn), Co, Ni and Pb in solution were measured to determine the environmental safety effects before and after bioleaching. The results show that the bioleaching rates of available silicon in the slag were mainly affected by the temperature, pH and pulp density. Under the optimal conditions of temperature of 30 °C, pH of 7.0, pulp density of 5 percent, shake flask rotational speed of approximately 210 rpm, particle size of approximately 0.150 mm and leaching time of 16 d, the concentrations of available silicon in the bioleaching system rose to approximately 110 to 140 mg/L. The metals remaining in the residues were mainly bonded in stable fractions, with concentrations lower in the leachate after bioleaching. This study demonstrates that silicate bacteria can be used to increase the contents of available silicon from EMR, and that bioleaching technology can realize the harmless resource utilization of EMR.

By Y. A. Attia

Auriferous sulfide ores often contain very finely disseminated gold and other precious metal particles inside the sulfide crystals. The encapsulation of precious metal particles gives rise to the refractory nature of such ores to current extraction methods. As a result, these fractions are frequently lost in the tailings. The purpose of this work was to investigate the feasibility of pretreating these refractory tailings with bioleaching before employing standard extraction techniques such as cyanidation. Leadville gold ore tailings containing auriferous pyrite were first concentrated by froth flotation. The pyrite concentrate was treated for different periods of time with 12 weeks adapted thiobacillus ferrooxidans before cyanide leaching. The bioleaching of the concentrate before cyanide leaching increased the gold extraction from 32% to 95% and that of silver from 48% to more than 98%.

Jan 1, 1987

By M. N. Herrera

The bioleaching of mineral sulfide pulps in a bench-scale rotating drum reactor has been studied. The reactor includes horizontal paddles in the inner wall for lifting of the mineral pulp. The performance of the reactor was tested in the bioleaching of a refractory pyritic gold concentrate in the presence of pure Thiobacillus ferrooxidans strain (ATCC 19859). The concentrate was efficiently bioleached at 50% pulp density with the drum operating at 0.5 -1.0 rpm Attempts of bioleaching the concentrate at the same pulp density in conventional stirred reactor showed severe inhibition of bacterial activity. The results demonstrated that the drum reactor allows to operate at much higher pulp densities than the conventional stirred tank reactor. This behavior is explained in terms of an improvement of the bacterial activity due to a better control of the attrition of the mineral particles.

Jan 1, 1997

By N. Parra, M. N. Herrera, T. Vargas, C. González, B. Escobar

The bioleaching of mineral sulfide pulps in a bench-scale rotating-drum reactor was studied. The reactor contained horizontal paddles on the inner wall for lifting the mineral pulp. The performance of the reactor was tested by bioleaching a refractory pyritic gold concentrate in the presence of pure Thiobacillus ferrooxidans (ATCC 19859). The concentrate was efficiently bioleached at a 50% pulp density with the drum operating at from 0.5 to 1.0 rpm. Attempts at bioleaching the concentrate at the same pulp density used in a conventional stirred reactor showed severe inhibition of bacterial activity. The results demonstrated that the drum reactor allows the process to operate at much higher pulp densities than conventional stirred-tank reactors. This results in improved bacterial activity because of better attrition control of the mineral particles.

Jan 1, 1999

By N. Parra, M. N. Herrera, T. Vargas, B. Escobar, C. Gonzalez

originally published May 1998, Vol. 15, No. 2, pp. 15-1 9 Discussion by G. Rossi, University of Cagliari Reply by T. Vargas, University of Chili

Jan 1, 2000

By Pierre Ollivier, Dominique Morin

A general study of gold refractory arsenopyrite pyrite concentrate bioleaching has been carried out including two continuous bioleach testworks at different sizes, namely one at a laboratory scale with a 100 1 unit at a 2 kg/d dry solid flowrate and the other at a pilot scale at a 100 kg/d dry solid flowrate. Both tests show a 80% bioleaching of arsenopyrite in about four days of treatment and with the same kinetic. Pyrrhotite is attacked at the earlier stage of the bioleaching but pyrite remains unaffected. The weak potential of oxidation associated with the decomposition of arsenopyrite and the abundance of arsenite leads to a high grade of elemental sulfur in the bioresidue which consumes the major part of the cyanide during the gold recovery, furthermore, the arsenite and ferrous produced in solution have to he oxidized to obtain a stable precipitate in the waste products and as outlined in previous works of other authors on this subject the addition of iron to obtain a Fe/As molar ratio at least above 3 is necessary. The agitation equipment used in the pilot unit allowed an optimisation study calculation for scaling-up the design and power requirements of an industrial installation, For the pretreatment of a gold refractory As high-graded concentrate the reagent cost has the greatest part in the operating cost of the biooxidation step due to the necessary retreatment of the biosolution, In that conditions the power cost is quite marginal, actually it is significant for the treatment of pure pyrite.

Jan 1, 1990

By Kevork Chouzadjian, Gary Davis, Nicholas Katsikaros, Bruce Kelley, Mellie Mavatoi

A process has been developed to recover gold and copper from two waste materials at the Bougainville Copper Limited mine in Papua New Guinea. It involves the bioleaching, in reactors, of a pyrite concentrate to liberate refractory gold and generate sulphuric acid, ferric sulphate and biomass for bacterial leaching of a chalcopyritic waste rock dump. Gold is to be recovered by cyanide leaching and copper by solvent extraction/electrowinning. The reactor bioleaching was developed in continuously operated reactors of 1 m3 capacity by CRA Advanced Technical Development at Cockle Creek, while the dump leaching was developed in 750 kg columns on site at Bougainville Copper Limited. The process was to be piloted on site.

Jan 1, 1990

By D. Kidd, T. Tucker, L. M. Indergard, S. Davis

"INTRODUCTION The Lisbon Valley Mining Co LLC (LVMC) operates the Lisbon Valley Mine located in SE Utah. The mine includes 3 open pits, 150-acre heap leach pad, and solvent extraction electro winning plant (SX/EW). Approximately 25MM tons of ore has been mined since 2005. The ore is stacked on the leach pad to an average height of 55 feet and occurs as a blend of crushed material (minus 2”) and run-of-mine (minus 24”). The host rocks include Dakota and Burro Canyon Sandstones. Copper occurs finely disseminated in this material at an average grade of 0.46%. Minerology is 63% sulfide, 27% oxide, and 10% insoluble. Total inventory mined through 2016 is approximately 230 MM lbs. METALLURGICAL CONSTRAINTS Copper production is constrained by areas of low permeability ore and geochemical issues, including acid consumption. The intrinsic permeability the ore ranges from 10-2 to 1 Darcy. This permeability does not permit sufficient aeration by natural convection, therefore oxygen transport is largely limited to the mass of oxygen that can remain dissolved in leachates. As a result, greater than 50MM lbs of copper remains in inventory and occurs secondary sulfides, including chalcocite, covellite, and bornite. BIOLEACHING FUNDAMENTALS Due to the higher activation energies of secondary sulfides, notably covellite and bornite, a strong oxidant is needed to remove an electron from the metal-sulfide lattice and release the copper cation into the sulfate solution. This process occurs most efficiently using the strong oxidant ferric iron (Fe3+). Ferrous iron can be oxidized to ferric iron by oxygen via chemical oxidation or biologically; which was measured to occur 500,000 times faster when using microbes versus oxygen.1 The microbes that oxidize ferrous iron (Fe2+) to ferric iron are naturally abundant and will develop biomass when appropriate conditions and nutrients present themselves. Most nutrients are provided by the ore/irrigation (P,N,Mg, Ca & Fe2+) while the others (O2 and CO2) are provided by air. In most cases, oxygen transfer is the rate limiting step during copper sulfide leaching. 1 Lacey & Lawson 1970 FORCED AERATION SYSTEM DESIGN This paper describes LVMC’s efforts to bioleach the remaining inventory by forced aeration. Two basic aeration systems were installed and tested including vertical wells and horizontal piping. Vertical System The vertical system was installed using the mine’s blast hole drilling rig. Wells were constructed using 4” high-density polyethylene (HDPE) connected to 4” polyvinyl chloride (PVC) screens similar to conventional bioventing wells. Ore samples were collected at each well location to characterize the spatial distribution of the remaining inventory along with fines (minus 200 sieve), pH (acid consumption), and iron. A block model of each analyte was developed and mapped in 3D."

Jan 1, 2017

By B. E. Dindsale, P. B. Altringer, R. H. Lien

The Bureau cf Mines, U.S. Department of the Intericr, is investigating biolcgical and chemical deccntaminaticn of cyanide- containing leachates and residues. Biolcgical cyanide cxidaticn, using bacteria isolated from a precious metals tailings pond, destroyed >85 pct of the cyanide in several prccessing solutions containing up tc 280 ppm CN. Reaction time varied from about 4.5 hr in a trickling reactor using quartz as a bacterial substrate to 2 mo in unagitated, covered flasks. Chemical techniques were used to destroy the remaining complexed cyanide down to 1 ppm. Exploratory tests were also conducted using spent ore from heap leach operations as the bacterial substrate to determine if biological cyanide oxidation could be used to destroy the residual cyanide in spent heaps.

Jan 1, 1991

By K. R. Gardner, P. B. Altringer, R. H. Lien

The Bureau of Mines, U. S. Department of the Interior, is investigating biological and chemical reduction of selenate and selenite from waste waters. A mixed bacterial culture, isolated from agricultural waters, removed selenium from four oxidized cyanide solutions from precious metals operations containing 0.6 to 30 ppm Se and 13 ppm CN. Up to 85% selenium removal was attained using bacteria under controlled batch conditions in a 3-L stirred tank reactor and in small-scale continuous tests conducted in a rotating biological contactor (RBC). Fe(OH), reduction of the selenium reduced the effluent concentration to 0.02 ppm Se; however, the reagent costs were prohibitive. A final processing scheme may involve a combination of biological and chemical treatments.

Jan 1, 1991

By D. L. Lampshire

Biological leaching using native heterotrophic bacteria was studied by the U.S. Bureau of Mines as a means of extracting manganese from a domestic low-grade wad ore. Column heap leaching simulation techniques were employed using molasses as the nutrient source for the bacteria. These column studies were designed to investigate the effects of molasses medium flow rate, concentration, and replacement interval on the extent and rate of manganese extraction. .Results showed that flow rates between 0.41 and 8.1 L/min/m2 had little impact on manganese extraction. The total amount of molasses used did have a direct effect on the extent and rate of manganese extraction. Manganese extractions over 90-pct were obtained in 12 weeks of bioleaching with 2-week medium replacement cycles.

Jan 1, 1993

By T. Maniatis, T. Pickett, B. Wahlquist

Biological destruction of cyanide in mining waters has been demonstrated effective in the lab and in the field. Applied Biosciences Corp.’s ABMet water treatment technology is used in the mining and other industries for the removal of various inorganic contaminants including metals and nitrate. An aerobic ABMet-CN process has shown great promise in efficiently and effectively removing cyanide from even very cold waters. Bench and pilot data will be presented.

Jan 1, 2004

By Robert H. Poppe

The Regional Copper-Nickel Study examined the potential impacts of copper-nickel sulfide mining, concentrating and smelting operations in northeastern Minnesota and gathered extensive monitoring data on the ecological characteristics of the region&apos;s aquatic and terrestrial biota. Because of the many development options possible, the diversity of the region&apos;s ecology, and the uncertainty of future environmental regulatory requirements, the Study did not attempt to measure the magnitude of environmental impacts on specific biological communities from a specific development proposal. The Study provides a broad base of environmental resource and impact information that hopefully will assist mining developers and environmental regulators when assessing specific proposals in the future. The following discussion is not a description of what will happen if copper-nickel development occurs in northeastern Minnesota but an exploration of why certain potential aspects of such development should be carefully considered and adequately understood before unnecessary or irreversible decisions are made.

Jan 1, 1980

By Leslie C. Thompson

The heap leach process used for recovering gold from oxide and sulfide ores is operated as a closed circuit system in which the cyanide process solutions are continuously recy­cled. In a well-designed operation there is little or no dis­charge of cyanide to the environment. Spent leached ore residues are water washed to remove most of the trace cyan­ides and precious metals remaining after completion of cyan­ide leaching. After the washing step, small amounts of cyanide, metal-cyanide complexes and nitrates remain in the residue. Most of the cyanide and nitrate residue constituents exist in the pore water of the spent ore rather than in the solid mineral fraction. More than 90% of the complexed cyanides in a freshly washed ore residue are present as free cyanide or weakly complexed metal-cyanides. Natural volatilization and decom­position rapidly remove most of these easily dissociable cyanides from the spent ore. Only the stable, strongly com­plexed metal-cyanides, such as gold, cobalt or the ferrocyan­ides and other constituents such as nitrates have a long term persistence in the spent ore residue (Towill et al). Despite washing and natural removal mechanisms, spent ore has the potential to act as a point source of com­plexed cyanides and nitrates for soil and groundwater con­tamination if inadequately contained (Huiatt et al). The groundwater contamination is caused by the leaching of the soluble cyanide compounds and nitrates from the pore water of the residue.

Jan 1, 1990

By E. G. Noble

Microbial leaching is being investigated as a method for recovering the metal values from a domestic low-grade manganese wad ore. Early work showed that heterotrophic microorganisms present in the ore solubilized manganese when cultured in a glucose-mineral salts medium. More recent shake-flask tests using molasses as the sole nutrient source extracted 97 pct of the manganese from minus 300- µm ore in 4 weeks. Column bioleaching with the molasses medium solubilized 99 pct of the manganese from minus 6.3-mm ore in 50 weeks. The results of flask, column, and lab-scale heap bioleaching studies are presented.

Jan 1, 1991

By J. David Gunn, Richard W. Lawrence

Gold and silver often occur finely disseminated in sulphide minerals such as pyrite. The use of biological leaching to dissolve pyrite and liberate gold has been extensively studied for a concentrate from the Porgera deposit, Papua New Guinea. The successful operation of a continuous bioleach circuit has been demonstrated. Bioleach residues were cyanide leached to extract gold and silver, and unreacted pyrite recovered for recycle to the bioleach. A 26 day steady state continuous bioleach test on a concentrate assaying 14.3 g/tonne Au and 87.0 g/tonne Ag produced residues with an average 73.5% weight loss and a pyrite oxidation of 88%. Cyanidation and recovery of pyrite from the cyanide residues for recycle gave overall recoveries of 92.1% gold and 74.6% silver. A proportion of the remaining precious metals was found in the bioleach solutions and may be recoverable. Losses to tails were 3.0% gold and 8.1% silver. Final tails represented 14.3% of the feed weight and averaged 1.84 g/tonne Au. A description of the continuous bioleach circuit and bioleach residue handling procedures, and the results of the study are presented. The features and advantages of biological oxidation as a pretreatment for refractory precious metal ores and concentrates are discussed.

Jan 1, 1985