Search Documents

By Alwyn Protheroe, Steve Smith, Herbert Jr. Gibson

In September of 2000, Cowin and Company, Inc., contracted with Paramont Coal Corporation to construct a large decline approximately 820 m (2,700 feet) in overall length at a grade of 8 degrees to the Lower Banner Coal Seam. This paper will discuss the methods used by the contractor and owner to overcome the unique problems required to construct this tunnel in a coal mine environment. The problems include, initial design considerations, equipment selection, ventilation, ground control, control of water in?ows, and placement of concrete.

Jan 1, 2003

By Bhaskar B. Thapa, Christopher Laughton, Michael P. Bruen

At Fermilab, located in Batavia, Illinois, a 4,000-foot underground complex of tunnels and caverns is being excavated on a decline of six percent, at depths of up to350 ft, below grade. The site geology consists of dolomitic and shale formations overlain by glacial till. Since the start of construction in March 2000, work to date has concentrated on the excavation and support of the Target Hall cavern, which is characterized by a low rock cover and a final lining of shotcrete. Ground vibrations, noise levels, and rock movement were monitored during excavation by drill and blast methods to prevent damage to experimental facilities, impacts on surrounding communities, and to allow evaluation of cavern performance. The cavern design was based on a UDEC numerical analysis that was validated during construction by comparison to encountered conditions and measured cavern movements.

Jan 1, 2001

By John J. Murray, Michael T. McRae, Michael A. Krulc, Kathy L. Schuler

The San Vicente Pipeline Tunnel Project involves the construction of an 8.5-foot-diameter water pipeline in an 11 mile tunnel in San Diego, California. The tunnel is located in extremely variable geologic conditions of strong granitic and volcanic rocks, weak sedimentary rocks, abrasive conglomerates, and mixed face conditions. One reach of the tunnel is a 5,200-foot mixed face reach that includes Friars Formation Conglomerate overlying granitic rock. Due to the variable ground conditions in this reach, the use of a TBM was deemed too risky and the contract documents required drill-and-blast and hand mining methods. Although it was not required, the contractor elected to construct this reach using NATM methods. This paper describes the geology of the 5,200-foot mixed-face reach, the design evaluation, and the construction challenges faced on this project.

Jan 1, 2007

By Vincent Tirolo

The proposed Second Avenue Subway is a new two-track subway line running from 125th Street and Park Avenue at the north, east along 125th Street to Second Avenue and south along Second Avenue to the Financial District in lower Manhattan, NY with 16 new stations and 13.6 km (8.5 miles) of track. The project has been broken into four construction phases. The initial Phase 1 operating segment includes three new stations (96th, 86th and 72nd Street stations) with a connection to the existing Broadway line at the 63rd Street Station at Lexington Avenue. Rehabilitation of the 63rd Street Station is also included in the scope of Phase 1. Subsequent phases extend service north and west to 125th Street (Phase 2), south to Houston Street (Phase 3) and finally to Hanover Square (Phase 4). The DMJM Harris/Arup Joint Venture (DHAJV) prepared the Contract Documents MTA for Phase 1. Parsons Brinckerhoff is providing the MTA with construction inspection services for Contract C-26002. In April 2007, NYCT awarded first Phase 1 for $337 million to S3 Tunnel Constructors, a tri-venture comprised of Skanska USA Civil, Schiavone and Shea. Contract C26002 is for the construction of the tunnel boring ma-chine (TBM) launch box and the mining of the TBM tunnels from 92nd Street to 63rd Street. The major part of the contract is to construct a shaft, commonly referred to as the launch box, from East 92nd Street to East 95th Street having dimensions of 244-m- (800-ft-) long by 18.9-m- (62-ft-) wide and a depth of 19.8 m (65 ft), including more than 91,000 m3 (119,000 cu yd) of soil and rock contained within its walls. The launch box will ultimately become the southern half of the 96th Street Station. The focus here is geological conditions at the launch box and existing structures along the launch box. These geologic conditions and existing structures had a major influence on the selection and design of the support of excavation system (SOE), the SOE bracing system, construction staging, the ground movements, dewatering and other challenges of constructing the launch box (Fig. 1).

Jan 1, 2013

By Erwin K. Roesner

The difficulties encountered while sinking deep shafts for Potash Mines in southern Saskatchewan have been the subject of several papers in the past. Geological and hydrological conditions of the strata overlying the potash deposits require special techniques for ground and water control during shaft sinking. The easily soluble potash ore requires the lining of these shafts to be virtually watertight to assure long term and safe operation. This paper describes the construction of the most recently completed potash shaft for the Potash Corporation of Saskatchewan. The shaft was designed and constructed by Thyssen Mining Construction of Canada Ltd. and it is located near Lanigan, approximately 110 km east of Saskatoon.

Jan 1, 1980

By Mirko Martini, Marcelo Benaglia, Andrea Codalli

Riachuelo Lot 3 forms part of a sanitation programme being implemented in Argentina to relieve the Riachuelo river basin from its current contamination. The programme, by far the most important in its kind in the country during the last decades, will expand the sewage capacity of Buenos Aires and will benefit an area of 4.3 millions inhabitants by intercepting a number of waste water discharges and conveying them to a new treatment plant prior to final discharge into the Rio de la Plata. The project foresees amongst other works the construction of an onshore 48 m deep shaft at the outlet of the treatment plant plus a 4,3 m inner diameter outfall tunnel of 12 km length. The last 1.5 km of the alignment is fitted with 34 vertical risers jacked from inside the tunnel to allow the discharge and dilution of the treated effluent into the Rio de la Plata. This paper describes the peculiarities and challenges, both in terms of design and in terms of construction, of the outfall tunnel, which was entirely bored under the Rio de la Plata using a 5.2 m cut diameter Tunnel Boring Machine (TBM). On one hand, the tunnel segmental lining was designed to work in tension during the system flow rate peaks while on the other the tunnel excavation faced a variety of complex conditions, such as crossing water bearing permeable soft ground formations and advancing at face pressures in excess of 3,5 bars for the entire route.

Jun 13, 2021

By Francesco Chiappalone, Marco Invernizzi, Franco Gasperin, Brad Yoder, Fabrizio Fara

The Ship Canal Water Quality Project includes a 2.7-mile, 18-ft and 10-in internal-diameter tunnel that extends from Ballard to Wallingford, two popular neighborhoods in the West of Seattle. During the TBM Main drive a 12' × 12' boulder with variable strength up to 47,000psi was encountered resulting on signicant damages to the Cutter ead. The rst part of this paper describes the design and construction of an underground recess in front of the TBM to create a safe working environment for the TBM repairs. The second part describes an injection campaign performed to seal an unforeseen water inow appeared during the excavation of the 11 Avenue Diversion Structure.

Jun 23, 2024

By Satoshi Honda, Mitsuru Shimizu, Tatsuji Nagao, Motoaki Kurisu, Hirokazu Izumi, Toshinori Takahashi, Hiroyuki Itoi

"1. INTRODUCTION Grade separation of roads and railway tracks is an effective method for solving traffic-related issues in cities. However, in urban areas where the existing traffic infrastructure is already overcrowded, construction of new roads often faces problems especially in the proximity of existing structures. This paper summarizes the construction plan and results of new road tunnel construction in the proximity of the piers of elevated tracks on the Tokaido Shinkansen railway.2. SUMMARY OF CONSTRUCTION AND ISSUES Auxiliary Route No. 26 as specified in the Tokyo urban plan is a project by the Tokyo Metropolitan Government, covering the construction of a new road with a total length of 22.3 km currently on the way to completion. In Shinagawa Ward, Tokyo, Auxiliary Route No. 26 is designed to cross the railway tracks of the Yokosuka Line and the Tokaido Shinkansen Line, so for this project, the East Japan Railway Company (JR East) was commissioned to design and build a road crossing under the railway tracks (Sumiyoshi Underpass). Figures 1 through 3 show a sketch of the Sumiyoshi Underpass. The Sumiyoshi Underpass was planned as a two-lane tunnel for vehicles, which was to cross under the railway tracks of the Yokosuka Line and the Tokaido Shinkansen Line at an angle of 70 degrees. The structure concerned is a single-story single-span box culvert structure with the following dimensions: 11.5 m wide, 7.7 m high and 31.6 m long. The Tokaido Shinkansen Line tracks were constructed on a girder-type elevated bridge built in the 1960s, and the foundation piles of the piers (P7 and P8) in the proximity of this crossing box culvert of RC structure were constructed using an earth drill method. The crossing structure for this project is located extremely close to the piers of the Tokaido Shinkansen railway tracks, with a minimal separation of 0.4 m, and the most significant issue of this project was construction in a manner that would not obstruct the normal operations of the Tokaido Shinkansen (Figure 4). Initially, we considered installing a temporary earth retaining structure in the proximity of the piers, cutting the ground and building an RC box, but concluded that it would be very difficult to apply this method because of probable excessive displacements in the Shinkansen railway piers. That is why we decided on the use of a non-open cut method in order to minimize the impact on the piers."

Jan 1, 2016

By Jim W. Rosteck, Anthony Del Vescovo

In December of 1992, the City of New York, Department of Environmental Protection, solicited bids for Contract 543B. The low bidder was a joint venture of Schiavone Construction Co., Inc. and the J. F. Shea Co., Inc. When completed, the project provides a 4.88 meter diameter water tunnel 8,840 meters long. This paper presents a case history of the equipment and construction methods utilized for this, the first portion of the New York City Water Tunnel constructed by use of a tunnel boring machine.

Jan 1, 1997

By Richard E. Lounsbury

Coal mine refuse handling traditionally has been the redheaded stepchild of the industry - a problem to be ignored as much as possible. During the past few years, however, mining companies have become more aware of the potential water pollution problem associated with refuse handling and storage. Planning for refuse disposal increasingly emphasizes protection of the environment as well as economics of refuse handling. Coal companies are responding to the environmental control needs by devising new systems and adapting well-known techniques to refuse handling systems. Monterey Coal Company has operated a non-polluting refuse disposal system at its No. 1 Mine for over two years. The purpose of this paper is to describe the design considerations given to the planning of that system and the operational experience gained during its construction

Jan 1, 1973

By Ehsan Alavi, Eren Kusdogan

The City of Toronto’s Coxwell Bypass Tunnel is currently being constructed by North Tunnel Constructors ULC, a joint venture of Jay Dee Canada, C&M McNally Tunnel Constructors and Michels Canada. This project includes construction of approximately 10.5 km of 6.3 meter finished diameter rock tunnel, five 20 meter diameter storage shafts and eleven tunnel connection drop shafts, along with associated deaeration and adit tunnels. This paper describes progress on the project to date and reviews the risk mitigation measures utilized on the project to move the project forward through tough geological conditions during shaft excavation and tunneling phase of the project.

Jun 13, 2023

By Yves St-Amour, Vince Luongo

This paper will discuss one of the largest construction projects the City of Portland has undertaken. This phase of the Willamette River Combined Sewer Overflow (CSO)project consists of approximately 18,500 ft of tunnel in soft ground, requiring the construction of six deep shafts and jet grout ground improvement. The purpose of the project is to reduce volume of combined sewerage overflows from the drainage areas on the west side of the Willamette River. Bencor-Petrifond-Pacchiosi Joint Venture was awarded a contract to design and construct six deep circular shafts, jet grout ground improvement for three bridges and jet grout ground improvement break-in/outs for some shafts. Of the six shafts the Pumping Station Shaft was the deepest and largest, requiring a permanent ground support system with a deep jet grout ground water cut-off to 335-ft deep. The joint venture used state of the art methods and equipment to achieve its objectives and build the structures through some very difficult alluvial soils to great depths next to the Willamette River. The paper will provide a general discussion of the shaft construction and jet grout ground improvement installed for this phase of the project. It will also discuss some of the technical challenges encountered while effectively managing risk and costs, resulting in a successful project completed in a timely manner.

Jan 1, 2005

By Jeremy Theys

The Sacramento Regional County Sanitation District (SRCSD) is improving the sewer system in the Natomas area of Sacramento, CA. The Upper Northwest Interceptor (UNWI) system is an ongoing series of tunnel pipeline projects that will provide sewer conveyance for all residents of northeast Sacramento County to the New Natomas Pumping Station, located North of downtown Sacramento, also in the city of Sacramento limits. The New Natomas Pumping Station then carries wastewater flowsto the Sacramento Regional Wastewater Treatment Plant in Elk Grove via the existing Lower Northwest Interceptor. The Joint Venture of Traylor Brothers, inc. and J.F. Shea (TSJV) were awarded the UNWI 1&2 project in late September, 2007. The planned 5.8 km (3.65 mile) construction route for UNWI 1&2 begins at the New Natomas Pump Station and runs north along the East Drainage Canal to the begin-ning of UNWI 3&4 at Bridgecross Drive. UNWI 1&2 includes approximately 5.8 km (19,240 feet) of 3.65 m (144 inch) inside diameter pipe using Earth Pressure Balance Tunneling Methods. The project also includes 16.76 m (55 feet) of 3.04 m (120-inch) diameter interceptor pipeline, twenty three access manholes spaced approximately 305 m (1,000 feet) apart along the alignment, a 2.13 m (84-inch) by 3.65 m (144-inch) transition structure, a 3.65 m (144-inch) by 3.04 m (120-inch) transition structure, and the connection of three existing sanitary sewer lines to the interceptor.

By C. R. Stephan

Explosion-resistant seals in underground coal mines isolate the environment within the sealed area from the active workings of the mine. The current United States Title 30 Code of Federal Regulations (CFR) requires these seals to be constructed of solid concrete blocks. The CFR also allows for alternative methods or materials to be used to create a seal if they can withstand a static horizontal pressure of 138 kpa (20 psi), provided the method of installation and the material used is approved in the ventilation plan. The purpose of this report is to identify those explosion-resistant seals that have been tested and meet or exceed all the requirements of the CFR.

Jan 1, 1997

By C. R. Stephan

Explosion-resistant seals in underground coal mines isolate the environment within the sealed area from the active workings of the mine. The current United States Title 30 Code of Federal Regulations (CFR) requires these seals to be constructed of solid concrete blocks. The CFR also allows for alternative methods or materials to be used to create a seal if they can withstand a static horizontal pressure of 138 kpa (20 psi), provided the method of installation and the material used is approved in the ventilation plan. The purpose of this report is to identify those explosion- resistant seals that have been tested and meet or exceed all the requirements of the CFR.

Feb 24, 1997

By Yukika Miyashita, Takahiro Inoue, Kenji Namikawa, Masashi Matsumoto, Junichi Koseki, Yoshihiro Terashima

"In order to construct an underground two-layer expressway branch junction structure with a height of 14.7 m and a width of 22.3 m, two shield tunnels in each layer were combined by using a non-cut-and-cover enlargement method in sedimentary soft rock. Before and during the construction work, preliminary analysis, in-situ investigations and laboratory tests were conducted to ensure the construction safety and to evaluate the deformation characteristics of sedimentary soft rock. The construction project was safely executed without any water leakage or collapse of tunnel working face. The predicted results from preliminary analysis were almost similar to the measured values. From the detailed investigation of measured results, it was confirmed that the deformation characteristic of the sedimentary soft rock was observed to a small extent as the ground deformation derived from construction work. INTRODUCTION In recent years, some newly constructed urban expressways in Japan are being planned as underground structures due to the consideration of roadside environment. The construction of such underground expressways is frequently conducted using a shield tunneling, a typical one of non-cut-and-cover methods, to prevent any adverse effect to traffic in arterial roads, operation of nearby commercial establishments, and daily lives of local residents during construction work. For underground urban expressway, the connections with existing road network on ground surface or on elevated sections are indispensable, which require the construction of an underground branch junction with large cross-section. This raises a technical difficulty regardless of the open-cut or non-open-cut construction method."

Jan 1, 2016

By R. A. Pond

Two 6.17 m (20 ft 3 in.) diameter raises, concrete-lined to 5.49 m (18 ft) inside diameter, were completed in 1978 at the Monterey Coal Company Number One Mine near Carlinville, Illinois, by Frontier-Kemper Constructors. These two raises are the largest in cross-section yet completed by full-face upreaming, and the success of this project is expected to increase the application of raise-boring to coal mine shaft construction. WHY 6.17 M (20 FT) DIAMETER ? Raise boring is well accepted in the metal mining industry for a variety of applications, and is gaining in acceptance in the civil works construction industry. The use of raise boring to construct vertical openings for coal mines has not been as widely accepted, even though coal mining requires, per mine, the greatest number of openings to the surface of any underground activity. Several factors have influenced the low utilization of raise boring in coal mining: 1. Coal mine shafts must often be of large diameter to pass the required high volumes of ventilation air at acceptably low water gage pressures. Cross-sectional areas of finished shafts exceeding 23.23 sq m (250 sq ft) are common. 2. The life of ventilation shafts is comparatively long, and the typical sedimentary strata overlying coal seams normally require that the shafts be lined. Shafts on the intake ventilation circuit must have permanent water-tight linings. 3. Unconsolidated overburden at the surface is often thick, and as reaming cannot be safely utilized in unconsolidated material,

Jan 1, 1979

By F. Daviess

A requirement for geological controls during orebody modeling results from the recognition of heterogeneous geological characteristics and/or abrupt variations in orebody geometries. While purely statistical methods are often sufficient for modeling uniform homogeneous deposits, and the only recourse for many that are extremely complex, geological interpretations can be extremely valuable as controls during the modeling process. The advent of relatively inexpensive, sophisticated graphical computer hardware and software has focused considerable attention on the three dimensional visualization capabilities now available to the mining industry. Orebody geometries can be easily imported into many systems as wireframe or solid models, rendered with shading and color, rotated in space, exploded into composite parts, zoomed into and otherwise displayed to awe any audience. The requirements for an initially meaningful, accurate, geological interpretation are sometimes lost when the focus is on an apparently complex, highly resolved end product. Details of the initial data and sensitivities of modeling assumptions are not always sufficiently scrutinized. Software capabilities have extended the geopoetic license into three dimensions. The new tools, while greatly facilitating model construction and rendering, have done little to expedite basic data preparation and analysis. This paper attempts to briefly summarize the purpose and method of the construction of geological controls. The examples selected are from wire­framing and block modeling; application software processes commonly used in the mining industry today.

Jan 1, 1992

By Jamal Rostami, Ataollah Rahbar

"Uma Oya Multipurpose Development Project is under construction in Sri Lanka. This project involves 2 Rolled Concrete Core (RCC) Dams connected through a tunnel currently under construction by Drill and Blast method. The water is transferred from first diversion dam to the 2nd regulatory dam and from which, it will be transferred through a 14 km headrace tunnel to the top of a 650 m deep drop shaft that feeds the high pressure water to an underground powerhouse and turbine chamber for generation of 120 MW of electricity. The Headrace and Tailrace tunnels are being excavated by two 4.4 m diameter double shield TBMs. The headrace tunnel has already passed 5km milestone and is mined in hard rock, while the tailrace tunnel has been completed in rather weak and fractured ground. This paper will review the history of the project along with the geology of the site. The operation of TBM in headrace tunnel will be discussed in more detail, focusing on the challenges of excavating through very strong and abrasive quartzite and gneiss on this site, as well as reaches of tunnel in high inflow of water reaching 400 L/Sec. INTRODUCTION This paper aims to introduce the Uma Oya Multipurpose Development Project (UOMDP) as a hydro mechanical project in Sri Lanka, targeted generating hydro-electric power, transferring water for irrigation purposes and controlling seasonal devastating flood. This project lies in the south-eastern part of the central highland region of Sri Lanka (Figure 1). The main part of the project is located in the south-western part of the Badulla district in the province of Uva. The south-eastern end of the project site is in the central west of the Moneragala district (province of Uva). Bandarawela is the largest urban setting within the project area, located halfway between the upstream and the downstream ends of the planned hydropower plant and combination of dams, tunnels, and downstream facilities. The Multi-Purpose Project Of Uma Oya is planned to convey water from Uma Oya to Kirindi Oya Basin for hydroelectric energy generation includes Puhulpola RCC Dam on the Uma Oya river, Dyraaba RCC Dam on the Mahatotilla Oya river, a conveyance tunnel from Uma Oya to Mahatotilla Oya (L=3750m), a long feeder tunnel from Mahatotilla Oya to Kirindi Oya. The feeder (power) tunnel Lot consists of a headrace tunnel (L=15554m), the surge shaft (L=200m) and tank on the upstream of the vertical shaft, a vertical shaft with steel lining (L=650m), an underground powerhouse and a tailrace tunnel (L=3650m)."

Jan 1, 2016

By Peter van Dijk, Gary Almeraris, Philip Rice

This paper describes the Contractor’s value engineering design and the construction of the Interstate I-90 highway tunnel sections under the South Station railroad yard in Boston, MA for the Central Artery/Tunnel Project, using tunnel jacking and ground freezing techniques. Three tunnel box sections were constructed and installed, with typical cross-sectional dimensions of 11.6 m x 23.8 m, and respective lengths of 50.9 m, 78.7 m and 115.6 m. A 12-compartment concrete shield was built as part of the front of each multi-sectional tunnel box structure. The jacking systems employed consisted of rear and intermediate jacking stations and up to 87 individual jacks, providing a maximum total thrust capacity of 42,300 t. The tunnel alignments pass through a geologic profile consisting of historic fill, which contains remnants of old waterfront structures, building foundations and a forest of 19th century vintage timber piles, underlain by organic sediments and marine clay. Ground cover over the tunnels is in the range of 1.8–7.6 m. The groundwater table is at depths of 1.5–3 m below surface grade. The paper discusses the techniques developed and equipment used to successfully build and install these tunnel box structures with minimal impact on the commuter and long distance railroad operations directly above the tunnel alignments. Figure 1 shows the track area at the I-90 EB and WB tunnels.

Jan 1, 2001