Search Documents

By P. K. Sims

One-day field trip via U.S. Highway 6 and Colorado Highways 119 and 279 from Golden, Colorado to Idaho Springs. This field trip provides an opportunity to observe aspects of the Laramide ore deposits in the Central City and Idaho Springs mining districts and the Proterozoic basement rocks, which host the ore deposits.

Jan 1, 1986

The global mining industry will always face significant challenges. Some, though, are bigger than others. What do you consider the major challenges facing the mining industry as a whole and SME in particular? Without a doubt, the major issue in both coal and metal/nonmetal mining industries is the ?graying? of the workforce in all aspects of mining. As the baby boomers continue to age, valuable experience is being lost by industry, government and academia. And there is the potential for SME to lose some of its membership. Now with that said, I should note that, despite the aging of the workforce, SME membership continued to grow by 7.1 percent during 2011.

Jan 1, 2012

By J. David Lowell

The first part of this article is a review of industry techniques and styles during the past 50 years. It is followed by my career history during the same period. The second part covers my ideas about what works in mineral exploration. These include estimates about discovery costs, thoughts about education of explorationists, organization of exploration groups and my opinions about the relative value of exploration techniques. Evolution of exploration techniques [Table 1] shows the evolution of mineral exploration techniques and styles from 1950 to 2000. During the first half of that period, there was a progressive increase in exploration drilling. During the second half, there was a decrease in prospecting and an increase in high technology, indirect exploration and a rapid increase in discovery cost.

Jan 1, 2000

By L. Gutierrez, S. Gering, C. Calderon-Arteaga

"Drill and blast represent the most important, and sometimes the costliest processes in the mine. The cost of drilling and blasting operations greatly contributes to the “high cost trends of the overall mining operations” (Afum and Temeng, 2015). The use of available information to improve the drill and blast processes can be the difference between a wasteful process and one that is optimized for costs, safety and desired fragmentation. Mining operations have access to several types of data sets that include a variety of different systems. This information can be used to improve, evaluate and apply processes for drilling and blasting. This may include different types of data from the different stages of the process (before, during and after the drilling and blasting operations), such as hole locations (planned and actual), penetration rates, drill operators, fragmentation (expected and resulting), explosive (design and usage), geology, vibration and others. This information can be used on its own or combined for further analysis to reduce costs, improve safety and evaluate results. Fortunately, due to advances in mining software, drill and blast engineers can exploit this data and create reports to evaluate results and improve the drill and blast process. However, as users start combining information from multiple datasets and establishing standard operating procedures for reporting across multiple sites, it becomes valuable to create auditable, automated and sustainable workflows for handling the information.In some cases, the task of aggregating and standardizing the data formats has already been completed and is available to consumers via the Enterprise Data Warehouse (EDW). A data warehouse team extracts data from the source systems and transforms it so that it is meaningful for decision support (Wixom, Watson, 2007). The author’s initial implementation plan for the drill and blast solution included using data stored at the sites on local servers. However, we learned early in the process that much of the work for aggregating and supplying the required data was already completed and was available in the EDW ready for use. This saved time, reduced risk and added value to the system.The goal for this case study is two-fold: to show how information can be used to make decisions and improve processes, especially highlighting the value of using an EDW for managing drill blast information; and to discuss how technical challenges encountered during the implementations were resolved. This article targets users that want to better manage their drill and blast data or try to set up standardized workflows for using this information.This case study will discuss the process of implementing a drill-and-blast workflow at multiple sites within Freeport-McMoRan (FMI) using both data at the sites and information available from the EDW."

Jan 5, 2017

By L. Gutierrez, S. Gering, C. Calderon-Arteaga

"INTRODUCTION Drill and blast (DnB) represents the most important, and sometimes the most costly processes in a mine.. The cost of drilling and blasting operations greatly contributes to the “high cost trends of the overall mining operations” (Afum B. O. and Temeng V. A. 2015). The use of available information to improve the DnB processes can be the difference between a highly expensive process and an optimized one. Mining operations have access to several types of data sets and key information from a wide variety of different systems. This information is normally used to improve, evaluate and apply processes for drilling and blasting. This may include different types of data from the different stages of the process (before, during, and after the drilling and blasting operations), such as hole locations (planned and actual), penetration rates, drill operators, fragmentation (expected and resulting), explosive (design and usage), geology, vibration, and others. This information can be used on its own or combined for further analysis to reduce costs, improve safety, and evaluate results. Fortunately, due to advances in mining software, drill and blast engineers can exploit this data and create reports to evaluate results and improve the DnB process. However, as users start combining information from multiple datasets and establishing standard operating procedures for reporting this data across multiple sites, it becomes valuable to create auditable, automated, and sustainable processes for handling the information. In many cases the task of aggregating and standardizing the data formats has already been completed and is available to consumers via the Enterprise Data Warehouse (EDW). A data warehouse team extracts data from the source systems and transforms it so that it is meaningful for decision support (Barbara H. Wixom, Hugh J. Watson, 2007). Our initial implementation plan for the DnB solution included using data stored at the sites; however we learned early on in the process that much of the work for aggregating and supplying the required data was already completed. The goal for this case study is two-fold: to show how information can be used to make decisions and improve processes, highlighting the value of using an EDW for managing Drill&Blast information; and to discuss how technical challenges encountered during the implementations were resolved. This paper is targeted at users that want to better manage their DnB data or try to set up standardized workflows for using this information. This case study will discuss the process of implementing a DnB workflow at multiple sites within Freeport McMoRan Inc (FMI) using both data at the sites and information available using the EDW. The paper will begin with an overview of the project. The discussion will then describe how DnB processes were used to set up daily workflows in order to provide information for evaluating process and making decisions. The final section will discuss some of the technical challenges and how they were solved, as well as possible next steps for further improving the workflow."

Jan 1, 2017

By Richard W. Kimball, Richard F. Coon

This paper describes drill and blast excavation and groundwater control measures at the Lake Mead Intake No. 2 project. The construction includes a deep access shaft, intake shaft, surge chamber, forebay chamber, intake tunnel, 22 well shafts and East Tunnel. Grouting ahead of the excavation face was used extensively during shaft and tunnel construction. Lake Mead Intake No. 1 was constructed in the early 1970’s under less severe groundwater conditions and this work was delayed by ground conditions and water control problems. Excavations for Lake Mead Intake No. 2 must be completed in 23 months to meet SNWA’s water delivery schedule.

Jan 1, 1999

By R. B. McCammon

Four areas have been identified as favorable drill-site locations for determining whether or not a suspected prophyry copper deposit exists in Rowe Canyon, Nevada. Favorability is based on the similarity to a deposit model constructed from geochemical data for the porphyry copper deposit near Ely. Favorability is defined as the coincident number of positive anomalies for the elements zinc, silver, arsenic, antimony and iron. The favorable areas coincide with an observed magnetic high and areas in proximity to major faults.

Jan 1, 1979

By Hassell E. Hunter

The Wyoming Mineral-Conoco Crownpoint Project represents the first time that big hole drilling has been exclusively used to develop totally a privately financed mine below a depth of 1000 feet. Three shafts, one ten feet in diameter and two six feet in diameter, were successfully drilled to depths of 2243', 2188' and 2188' respectively and cased with hydrostatic designed steel casing. The largest shaft is to be used to handle muck and water from station excavation and enlargement of the other two shafts. A reverse circulation system with potassium chloride base mud was used for drilling. The mud was cleaned by settling in steel lined tanks with assistance by cyclone type separators. Deviation was monitored by gyroscopic surveying at 30 foot intervals and did not exceed 16 inches off plumb. Casing was designed to withstand hydrostatic pressures with a 1.5 safety factor to the large shaft and 1.25 safety factor for the smaller shafts. All casing welds were x-ray tested prior to lowering the casing in the hole. Cementing the annular space completed the operation. The total time to mobilize, drill and move off the three shafts was 363 days. The drilling operation was completed ahead of schedule and under budget.

Jan 1, 1983

By R. P. Proulx

The Meikle Mine is a high grade, underground goldmine utilizing primary-secondary longhole open stoping with delayed backfill to produce 2700 tpd(3000 stpd) of ore. Hot and reactive ground conditions were encountered early on in the mine life. Ground temperatures up to 166°C (330°F) were measured. In the early stages of mining, the mine experienced premature detonations using different explosive products. The learning curve to safely mine this high-grade gold deposit in hot and severely reactive ground was indeed very steep. Currently, the Meikle Mine uses a special buffered bulk emulsion in all blasts to address hot and reactive ground concerns. In addition, exacting procedures are also followed to ensure safe work with explosives. The combination of new explosives technology and strict loading procedures permits high mine productivity with the highest degree of safety.

Jan 1, 2000

By Richard W. Amerman

The final cost and quality of a project employing equipment, labor, and materials is dependent upon the expediency and extent to which each of these parameters are used. An ideal solution then, would be one in which three solvable equations were given for each particular situation. The equipment, labor, and materials could then be solved for, and the perfect job would result. In reality, however, the ideal and most economical solution is seldom attainable by solving three given equations. Therefore, knowledge, experience, and sometimes guesswork must be relied upon when correlating equipment, labor, and materials. Drilling and blasting, in particular, is one operation which normally involves more uncertainty than other operations. It is also an operation in which the outcome is extremely critical for two reasons. First, the cost of the operation that follows drilling and blasting is dependent upon how well the material is fragmented. Second, once the drilling and blasting has taken place, it is impossible to return to the area, without considerable expense, and correct any mistakes that might have been made. Therefore, what is desired is a method by which drilling and blasting operations can be performed yielding optimum results at the lowest cost; this can best be accomplished by having the relationships between equipment, labor, and materials prior to their use. For obtaining best results, the selection of these three relationships must be based on knowledge, experience, and as little guesswork and uncertainty as possible.

Jan 1, 1969

By B. J. Dave, Ashok J. Desai, Allen J. Hulshizer

This paper presents various design and construction considerations involved in developing an underwater installation of lined, large diameter shafts not known to have been previously accomplished for the diameter size, depth or ground conditions identified with the Seabrook Power Station. Outlined approach provides for driving tunnels independent of shaft sinking operation, permits the use of prefabricated shaft lining and incorporates a safe dry tap method for connecting the shafts to the tunnels. INTRODUCTION The Seabrook Power Station, located two miles inland from the Atlantic Ocean, at Seabrook, New Hampshire, is a two unit, nuclear powered, electric generating plant, each unit having a capacity of 1150 megawatts (electric). Typical to all steam driven generators is the requirement for large quantities of water. Requirements for the Seabrook Plant will be met by intaking and discharging approximately 850,000 gpm of ocean water at a considerable distance from the shore line in water depths that render the environmental impact inconsequential. Obtaining, conveying and discharging such large quantities of water represents a major undertaking, particularly under today's environmental controls. Tunnels are well suited to reducing the environmental impact at the Seabrook site by conveying the water about 250 feet deep under the salt marsh (a valuable ecological feature) and under the beach well out into the ocean without any noticeable ground surface disturbance. An alternate approach utilizing trenched piping would have created some disturbances and was environmentally less desirable. The tunnels connect to intake and discharge

Jan 1, 1976

By A. P. Wickland

The characteristic problems related to drilling a hole for evaluation of an orebody are generally quite similar, whether we're drilling a core hole, or a hole to obtain chip samples. The basic objective in each case is fundamentally an economic factor; to produce the maximum amount of usable information per hole at a reasonable footage price. The success of the drilled hole depends largely upon the amount of investigation and research spent on the prospective area and the ability to forecast the capable personnel needed plus the right kind of drills, ancillary equipment such as bits, muds and various additives necessary to make the drilling program successful. The driller is confronted with a wide variation of drilling problems due to the nature of subsurface conditions. Some of these problems are: overburden, which may consist of clays; sand; boulders; or glacial till. These surface conditions may exist up to 2,000 feet in depth and upon reaching bedrock, formations may consist of swelling shales, broken sandstones, and every conceivable rock-type, coupled with every known structural problem such as dips, faults, folds, etc., and to this added extras such as permafrost and/or ground water problems combine to increase the necessity why an understanding of the problems along with the proper reaction of the driller plus the formula to compensate for ground conditions is necessary to complete a drill hole. Since most geologists are familiar with diamond core drilling techniques, I would like to discuss other methods used in evaluating ore deposits.

Jan 1, 1973

Market confidence is on the rise and industry leaders turning toward the vast and diverse region of Latin America are faced with abundant, yet daunting, opportunity. From the iron orebodies of Brazil to the renowned copper mines of northern Chile, drilling teams in Latin America are often faced with abrasive, broken ground. These types of ground conditions tear up coring bits rapidly, making it extremely difficult for even the most seasoned drilling teams to maintain effective productivity. The drilling challenges faced in this rich and opportune region are being met today by advanced coring technology, bringing with it the potential for increased productivity in Latin American mineral exploration.

Jan 3, 2010

By N. Del Bel Belluz

Drilling underground in the Grasberg De-watering drifts has routinely hit water aquifers with high flow rates and pressures. Two types of holes are utilized; pilot-holes to probe ahead of the tunnel development to intersect aquifers ahead of the face; and de-watering holes to de-water rock formations that will drain water from the Grasberg pit and allow tunnel development to proceed safely. Recently, rates of 1050 psi static pressure have been recorded with flows from a NQ hole measured at 1350 gpm (US). The water flows can be slightly acidic, necessitating the use of stainless steel collar gear to resist corrosion. These rates were anticipated and contingencies were planned early to deal with these conditions. The collar gear is used to control water flows whereby the water is treated as an important resource. As a result, pm has established procedures to maintain safety of the drill crews, enable coring of the rock and to maintain safety of the miners who are driving the drifts.

Jan 1, 1998

By D. A. Saint Don, M. Prueher, S. Barnwell

With the current changes in technology, multiple methods are now available for aggregate resource identification. From Sonic to Coring, Reverse Circulation to Percussive, there are many choices to make regarding drilling technology. The discussion will outline the methods above with focus on aggregate investigation and highlight the new technologies that will make a difference in your search.

Jan 1, 2004

By Alex Ruzycki

Gold Fields-Mesquite is a 7.5 million ton per year heap leach operation located in the Maj ave Desert of Southeastern California. Extraction of gold is carried out on multiple lifts, with over 33.3 million tons of ore leached since the inception of operations in 1985. The delineation of the gold left in heap residue is a formidable task. Gold removed from active leach areas can be routinely monitored through sampling of emerging solutions but exact recoveries from specific heaps remains nebulous due to factors such as cross flow between sections buffering effects from multiple lifts, and releaching. In order to better quantify ultimate heap recoveries and increase releach efficiency, Mesquite initiated a residue drilling program. The project progressed through an evaluation of sampling protocol, drilling of residue by reverse circulation, entry of assays into a software package capable of producing grade-based contour maps, and a production scale releach test that evaluated the system's ability to predict residue grade.

Jan 1, 1992

By James G. Tilton

Throughout the world, sedimentary basins are exploited for many different minerals. Frequently, the extractive methods conflict with one another. A case in point is the proximity of oil and gas operations and the mining of coal. Generally, the interference between the two industries lies in the fact that the reserves over- lie or underlie one another. Mining of coal generally is developed on a rectangular pattern in a horizontal mode while oil and gas drilling is developed on a radial pattern in a vertical mode. Coal mining has exhausted vast acreages in various basins with many of those basins being drilled for oil and gas. Those existing wells create problems by requiring the unrecoverable coal pillars to support the well bore, or to make special provisions in order to mine through an existing well. The system works ... more or less; but there are little or no provisions made for additional drilling unless the vast majority of those new wells are drilled through mined-out sections (gob) of those mines. Many states have rules and regulations governing the drilling of oil and gas wells through gob; but, some companies and some regulatory agencies or personnel have deemed such drilling as a hazard to the mining operations. This paper explores the history, technical standards, and safety aspects of drilling oil and gas wells though the gob of worked-out and active mines. It is the opinion of the author that such drilling can be conducted safely while eliminating the re- quired changes in mine projections and the loss of recoverable coal in the form of well pillars.

Jan 1, 1997

By Robert S. Mayo

My subject today is "Drilling-and-Blasting of Small Rock Tunnels". I am sure that there will be some people, primarily college students but perhaps Consulting Engineers, who will say: "Drilling-and-Blasting? I thought that went out with the invention of the Tunnel Boring Machine". A few years ago I talked to Dick Robbins and he told me that they did not try to sell a "Robbin's Mole" unless the tunnel was two miles long. For easy calculations I use 10,000-ft. (3km) A Mole today costs about $2 million which works out to $200 per lineal foot. This is "front money". You cannot place the order unless you are the uncontested low-bidder and then you must wait at least six months for delivery. Of course you can use that time to square up your portals, ready to turn-the-eye, or maybe you have shafts to sink to reach the tunnel grade. But this is "dead-time" and it is a heck of a feeling to have a job and cannot get started on it until you get the Mole. I do not have the American figures on lengths of tunnels but there was an article a few years ago in a British magazine: NEW CIVIL ENGINEER, on this subject. This stated that 75% of the jobs in Britain which were bid were for small tunnels, 10-ft x 10-ft (3m x 3m) or smaller, and that they were less than 5,000-ft (1.5km) in length. This does not mean that 75% of the footage in Britain was less than 10-ft in diameter. It means that 75% of the jobs being bid were less than a mile in length. From my experience in the U.S. I believe that we have substantially the same ratio: so many of the jobs with which I was associated were short, 1,000-ft, 2,000-ft and sometimes 3,000-ft and the bores

Jan 1, 1981

By R. Fedors, T. Ghezzehei, D. Or

The phenomena of dripping into cavities (e.g., tunnels and drifts) within an unsaturated fractured porous medium under ventilated conditions was studied to improve estimates of dripping rates, drop sizes and the chemical composition of droplets that could affect the integrity of high-level nuclear waste packages placed in drifts. The sensitivity of dripping rates and water chemistry to ventilation was analyzed at various flow rates using analytical expressions linking flow on fracture surfaces to drop formation and evaporation. The model was tested using laboratory experiments involving machined aluminum slabs designed to represent a simplified morphology of a fracture face intersecting a cavity and using natural fracture surfaces from a welded tuff Comparison with ten years of data on dripping in natural caves showed good agreement with model predictions. In particular, for low dripping rates, evaporation due to ventilation leads to larger drop sizes and alters drop chemistry by increasing the concentration of solutes in the drop relative to that in the water flowing on the fracture face.

Jan 1, 2002

By R. Fedors, T. Ghezzehei, D. Or

The phenomena of dripping into cavities (e.g. tunnels and drifts) within an unsaturated fractured porous medium under ventilated conditions is studied to improve estimates of dripping rates, drop sizes, and chemical composition of droplets that could affect the integrity of high-level nuclear waste packages placed in drifts. The sensitivity of dripping rates and water chemistry to ventilation is analyzed at various flow rates using analytical expressions linking flow on fracture surfaces to drop formation and evaporation. The model was tested using laboratory experiments involving machined aluminum slabs designed to represent a simplified morphology of a fracture face intersecting a cavity and using natural fracture surfaces from a welded tuff. Comparison with ten years of data on dripping in natural caves showed good agreement with model predictions. In particular, for low dripping rates, evaporation due to ventilation leads to larger drop sizes and alters drop chemistry by increasing the concentration of solutes in the drop relative to that in the water flowing on the fracture face.

Jan 1, 2000