Search Documents

By Jin Kim, Jerry C. Tien

Water is still the most economical and popular means of controlling dust underground. It is a process that captures dust by bringing water droplets into intimate contact with coal particles. Wetting agents, also known as surfactants, can be added to greatly facilitate such a process since they tend to reduce the interfacial tension between the coal particles (usually hydrophobic) and the liquid. The surfactants used in the study were first chosen on the basis of their HLB (Hydrophile-Lipophile Balance) value, and later tested in order to select the right type and amount of surfactants to give the best performance. Both static and dynamic tests were later conducted using different types of surfactants to examine their respective wetting effectiveness on coal particles. Experimental results show close correlation with the theoretically calculated collection efficiency that is based on a horizontal tunnel and a solid-cone water spray.

Jan 1, 1993

By B. Spigarelli

Carbon dioxide sequestration by conversion to carbonates has become a promising option for CO2 storage. Experiments were conducted to determine the feasibility of CO2 sequestration at ambient conditions using a Ca-rich industrial waste in a carbonate solution. The Ca-rich industrial waste used in this study was lignite fly ash. Fly ash was chosen because it is cheap, available near large CO2 point sources, already in powder form, and reactive due to amorphous properties. In the experimental set-up, CO2 absorption was inferred by monitoring feed and exhaust gas CO2 concentrations. The addition of an alkali to a fly ash-distilled water solution provided a 50% increase in CO2 absorption of the solution. Absorption time also increased by 50% compared to a fly ash-distilled water solution. TGA analysis was used to determine the extent of CO2 sequestration in the carbonate form. At a liquid to solid ratio of 20:1, the conversion of ?free? calcium to carbonates was 75%. A CO2 balance on the system concluded that at the current operating conditions 42% of the total CO2 fed to the system was sequestered in the carbonate form. SEM-EDS analysis of the fly ash particles before and after reaction with CO2 indicated that the carbonate compound being formed was calcium carbonate. The analysis identified rhomboidal structures on the surface of the fly ash particles after reaction with CO2, but not before. These rhomboids are characteristic of calcium carbonate formation and they had higher Ca, C, and O concentrations than the host spheres, suggesting calcium carbonate formation.

Jan 1, 2012

By J. Sharp, R. Arnold, P. Rusin, T. Young, N. A. Sinclair

Many oxide silver and molybdenum deposits remain undeveloped because chemical extraction yields poor recoveries or is environmentally unacceptable. Bioreductive leaching of such ore samples at MBX resulted in high extractions of silver and molybdenum. When baseline, three-day, cyanide bottle-roll tests were conducted on manganiferous-oxide silver ore, 13.7% of the silver was extracted. In contrast, 86% of the silver was microbially solubilized into the organic growth medium by bioreduction with 99.8% dissolution of manganese. A followup cyanide bottle-roll test yielded an additional 8.5 % silver dissolution, for a total extraction of 94.5%. Baseline, three-day, acid bottle-roll tests of the iron-oxide molybdenum ore Yielded 1.8% molybdenum. However, bioreduction solubilized 93.3% of the molybdenum into the growth medium. An additional 0.3% molybdenum was solubilized during the followup acid bottle-roll test. Microbial treatment of refractory oxide ores with bioreductive bacteria resulted in higher extractions of silver and molybdenum than conventional chemical leaching. The bioleaching process occurred at a near-neutral pH at ambient temperatures. The bacterial solubilization of silver and molybdenum was achieved without the use of cyanide or sulfuric acid.

Jan 1, 1993

By D. Tao, B. K. Parekh

Fine coal particles are difficult to separate effectively from liquids or other solids. Ultrasonic energy may be used to enhance the efficiency of the conventional fine-particle separation processes widely used in the coal and mineral industries. Flotation, settling and dewatering tests were conducted using several fine coal samples to study the effects of ultrasonic treatment on these processes. Process variables such as particle size, ultrasonic treatment time and solids concentration were investigated for their impacts on ultrasonic treatment effectiveness. The results obtained from this study showed that ultrasonic treatment is an effective approach for enhancing solid/solid separation in flotation and solid/liquid separation in sedimentation and dewatering of fine coal. SEM microphotographs demonstrate that ultrasonics cleaned particle surfaces, which is, in part, responsible for the observed improvement in fine coal separation processes.

Jan 1, 2000

Recent U.S. mine disasters identified a need for improved training of miners in escape from mine fires and explosions. Researchers at the National Institute for Occupational Safety and Health?s (NIOSH) Spokane Research Laboratory (SRL) have designed fire-escape training software for use in a mine-safety training course. The software allows four trainees to work together in a virtual world via a computer network. Trainees responded favorably and showed a marked improvement in locating the proper evacuation routes on subsequent trials. In collaboration with the Pittsburgh Research Laboratory (PRL), a more elaborate fire evacuation scenario is being developed. Further study is needed to confirm that virtual training will translate to improved safety outcomes in the real world. Keywords: virtual reality (VR), safety, training, mining, mine fire evacuation

Jan 1, 2009

By M. Fan, A. Hobert, W. van Dyk

Low flotation recovery and selectivity have been long-standing problems in the treatment of most ultra-fine phosphate ores. This paper investigates the improved flotation of two ultra-fine Brazilian phosphate ores from Itafos’ Arraias project. These ores are predominantly composed of quartz, muscovite, apatite and a Ca-Al phosphate. As a result of fine phosphate dissemination and associated grinding requirements, column flotation was selected for the metallurgical test program to address the inherent limitations of fine particle flotation using conventional flotation cells. Accordingly, both benchtop Denver cell and laboratory column flotation tests were conducted to optimize their respective flotation responses. Improved flotation performance was achieved using column flotation as compared to benchtop mechanical flotation. In column flotation, a P2O5 concentrate grade of 30.5-31.0% was yielded at a flotation recovery of 83.7-85.1% for the 38x0µm generated ultrafines. The benefits of Eriez’ column flotation technology realized from this study include a higher degree of selectivity, increased recovery, and reduced collector dosage as compared to bench-scale mechanical flotation.

Mar 2, 2022

By M. Fan, R. Letkiewicz, A. Hobert, J. Milbourne

Ultrafine copper, gold and silver minerals flotation has become increasingly important because of the rising demand for processing finely disseminated ores. This paper investigates the improved flotation of ultrafine ores from a Troilus Gold project. Troilus is primarily an Au-Cu deposit but contains minor amounts of Ag, Zn and Pb, as well as traces of Bi, Te, and Mo. As a result of ultrafine Cu-Au-Ag dissemination and associated grinding requirements, Eriez’ column/StackCell and Denver benchtop cells were utilized to optimize their respective flotation responses. Enhanced flotation results were achieved using column and StackCell technologies. KAX 51 and SPRI 206 collectors, Na2SO3, and ZnSO4 depressants were the primary reagents employed. In column/StackCell flotation of three main mineral deposit ore composites, the rougher-scavenger-cleaner circuit Cu, Au and Ag flotation recoveries were 90.4~95.8% at a copper grade of 13.6-17.4%, 87.5-95.1% at a gold grade of 101-145.9 g/t, and 88.6-91.8% at a silver grade of 62.6-251.4 g/t, respectively. The benefits of Eriez Column/StackCell flotation technologies include high flotation selectivity and increased recovery due to unique hydrodynamic designs. Specifically, the StackCell design facilitates high turbulent kinetic energy dissipation rates to improve fine particle recovery and incorporates countercurrent wash water to significantly reduce hydraulic entrainment of the finest size gangue minerals to the froth product.

Feb 1, 2023

By C. L. Jiang, B. K. Parekh, X. Shao

Among the impurities present in phosphate ore, dolomite is the most difficult to remove. This is because dolomite and phosphate have similar chemical compositions and because the dissolved species of dolomite is adsorbed on the surface of the phosphate mineral. A new amphoteric surfactant was found to be a suitable collector for the separation of dolomite and phosphate. Flotation results showed that the new amphoteric collector had a high flotation selectivity for dolomite over a wide pH range. studies on the flotation of francolite and dolomite in each other's supernatant demonstrated that the dissolved ions had little effect on the selectivity of the new collector. It was found, however, that the dissolved ions were detrimental to the flotation separation using sodium oleate as collector. From a mixture offrancolite and dolomite containing 26.2% P2O5, a phosphate concentrate containing 35.2% P205 with a 90% recovery was obtained using 290 g/t of the amphoteric collector. The rejection of MgO was 81.41 %.

Jan 1, 1999

By C. S. Caldwell, L. C. Thompson

Mine closure and reclamation issues have evolved over the past several years becoming further complicated by stricter standards and by the cmrent economic climate and price of gold. Many mine permits are calling for more stringent remediation of spent ore heaps and tailings. Leachate solution water quality must meet strict discharge criteria for multiple parameters besides cyanide at mine closure. Closure standards are more difficult to meet and most mines do not have an increased budget at the end of mine life to deal with the falling standards. These issues make additional gold recove1y at the end of mine life a critical problem in financing some closure operations. Another issue is the length of time that must be budgeted for heap rinsing operations. Innovative biological processes developed and applied by Pintail Systems, Inc. at numerous mine closures have indicated that bio-processes can significantly enhance gold recovery dur­ing heap cyanide bio-detox over the recoveries expected from rinse operations. If heap rinsing can be eliminated or reduced and if gold recovery can be improved at the end of mine life, many mine closures may be possible with processes that pay for themselves or generate profit. Additional advantages of the bio­detox technology is that it can be engineered to treat multiple contaminants besides Weak Acid Dissociable (WAD) cyanide. Other contaminants treated in heap process solutions include nitrates, ammonia, heavy metals, thiocyanate and total cyanide. At the Cripple Creek and Victor Mining Company Ironclad Mine near Victor, CO, 5 million tons ofrinsed, heap leached spent ore were biologically detoxified to reduce cyanide content, enhance gold recovery during bio-detox and to reduce dissolved metals in heap leachate solutions. During the bio-detox treatment period a substantial improvement in gold recovery allowed the detox oper­ation to operate as a profit center. Final gold recovery was at least twice what was expected from a normal rinse operation.

Jan 1, 1998

By N. Moony

The benefit of gravity separation in improving total gold recovery in grinding circuits has been outlined in a significant number of papers to date. However, the use of batch centrifugal concentrators (BCC) as an industry standard to extract gold has limited the potential for maximizing gravity recoveries -particularly in coarse gold deposits. This is a reflection of the high upgrade ratios obtained by BCC's which has an inverse relationship with recoveries. Survey work in Australia has indicated that installation of the InLine Pressure Jig as an alternative to the Bee will significantly increase recoveries of gold by gravity and, accordingly, increase total gold recoveries and lower operating costs.

Jan 1, 1998

By Denis M. Riley, Neville C. Lockhart, Bruce A. Firth

The potential use of the Kelsey Centrifugal Jig to clean fine coal has been studied. It was found capable of cleaning coal at very fine sizes, at least to 0.038 mm at relative densities as low as 1.6. This effect was however very dependent upon the solids feed rate and the absence of significant amounts of clay slimes. Comparisons with a spiral and a laboratory scale Jameson Flotation Cell were made. The concept of recleaning spiral product was investigated. Use of a spiral to reclean the coarse fraction, and a centrifugal jig or flotation to treat the fine fraction, gave significant improvements in final ash values over spiral recleaning of the full size. Future R&D needs include improving feed rate capacity, and application to problems like pyrite removal that are difficult to solve via flotation.

Jan 1, 1995

By B. C. Paul, R. Q. Honaker, K. Ho

Recent research has shown that froth flotation is not effective at treating fine coals (-28 mesh) containing a large portion of middling particles. Due to their relatively large density differences, middling particles can be separated more efficiently using gravity-based processes. The ability of gravity separators to treat fine particles has been limited by the lack of particle inertia relative to the surface drag forces. However, particle inertia can be enhanced by the application of a centrifugal field. A commercial-scale centrifugal Falcon concentrator capable of treating a mass flow rate of greater than 1 tph continuously has been used to evaluate its feasibility for treating fine coal as an alternative to froth flotation. Tests conducted on a -28 mesh fine coal circuit feed have found the Falcon concentrator to be very effective at cleaning the 28 x 325 mesh size fraction. For an Illinois No. 5 coal sample, the ash content was reduced in the 100 x 325 mesh size fraction from about 18% to 8% while achieving a high combustible recovery value of nearly 97%. In addition, the total sulfur content was substantially decreased from 2.6% to 1.7%. The effects of the critical operating parameters on separation performance have been studied and their values optimized.

Jan 1, 1995

By S. Orr

Flow in heaps and dumps is a two-phase flow phenomenon, though for many applications it could be simplified as unsaturated flow. Unlike saturated flow (typical of ground water flow), where permeability is independent of other hydraulic parameters, unsaturated flow permeability depends on the degree of saturation and/or on capillary pressure. Several recent field studies suggest that flows in heaps and dumps tend to concentrate in preferred pathways, bypassing much of the ore. Different preferential flow phenomena are triggered, promoted and influenced by different heap structures, by pretreatment, by the composition of the leach solution and by application rates and schedules. The structure of heaps and dumps is determined and affected by every stage of their construction -from blasting to crushing to conveying and stacking of the material. History of heap construction and operation combined with monitoring, mapping and certain field tests can reveal patterns of flow and transport in a given heap and can shed light on the physical mechanisms behind it. Such insight can provide a first cut on heap leaching enhancement by either eliminating or bypassing physical barriers to flow and leaching. Based on the understanding of the heap structure, advanced flow and transport models can be constructed and further enhance the insight. This insight is essential for understanding cause and effect and can provide a basis for decision making. Further, based on the physically-based models, an intelligent control agent, such as MRDS1, can learn and build a self-learning representation (or a model) of the complex heap leaching system, followed by dynamic optimization and planning of heap leaching and heap rinsing.

Jan 1, 2003

By V. Vesselinov, S. Orr

"Enhanced heap leaching - Part 1: Insights" (Orr, 2002), different flow and transport phenomena that could significantly reduce leaching recovery were investigated. The combination of such understanding with advanced flow and transport modeling establishes the link between cause and effect, thereby, directing operators to optimal design and construction of new heaps. Modeling of flow and transport in heaps could also point to a unique change in application method or rate that would maximize leaching enhancement of an existing heap under existing situation and leaching history. The use of such a model is cost effective in that it can simulate multiple scenarios of alternative leaching enhancement methods. By simulating a large number of irrigation scenarios, such a model can point to the optimal and/or the most promising alternatives for a particular heap. The authors' simulations concentrate on the effects of changes in application rates and heap design on changes in flow paths and enhanced leaching recovery. Based on such simulations, an intelligent control agent, such as Multiple Resolution Decision-Support System (MRDS) (Meystel and Albus, 2002), could build a new representation of the complex heap-leaching system. And, by learning from historical data and current information, it could provide optimal management of heap leaching and heap decommissioning.

Jan 1, 2003

By D. Doepker

The dissolution of metals from various metal/ non-metal mine tailings has been studied through column leach tests at US Bureau of Mines laboratories. Metal mobilization in unsaturated columns was consistently greater than metal dissolution in water-saturated columns. Leachate pH was also frequently lower when a leachant was passed through columns but showed a mixed residence-time dependence. On the other hand, metal and sulfate ion concentrations in the leachate increased with dry-cycle residence time. Results suggest that acid formation through atmospheric oxidation of pyrite may compete with non-acid-forming oxidation of other metal sulfides. The two processes lead to decreased pH and increased metal mobilization, respectively. Leach tests using sodium lauryl sulfate indicated that microbial activity was not a factor in these studies.

Jan 1, 1991

By H. -S. Yoon, C. -J. Kim, K. W. Chung

"With the final goal of ultrasonic application to ion exchange in a resin-in-pulp (RIP) system, the feasibility of an indirect ultrasonic application with a submersed ultrasonic probe was investigated first for the enhancement of ion exchange in the following resin-in-solution (RIS) system: Lewatit MonoPlus MP 600XL in an artificial solution with 106 ppm uranium. Ultrasonic radiation enhanced the ion exchange efficiency without mechanical degradation of resin. For 3.6 g/L of resin, the enhancement was 79 percent after 10 min of ion exchange and it gradually decreased to 11 percent at 60 min. In addition, a preliminary test of the mechanical stability of the resin in the RIP system showed little mechanical fracture of the resin due to ultrasound, which indicates that indirect ultrasonic application by a submersed ultrasonic probe is applicable for RIP systems. IntroductionIn uranium ore processing, the ion exchange process has been used on a commercial scale for preconcentration and purification (Gonzalez-Luque and Streat, 1984). The ion exchange process is divided into two processes: (1) a resin-in-column process with the uranium-bearing solutions passed through columns containing resins and (2) a resin-in-pulp (RIP) process with the leached ore pulp exposed to resins. The latter does not require the separation process of leach liquor and ore solids, which reduces process costs. This process, which has been developed commercially since 1955, has a certain drawback. The adsorption rate and efficiency in the RIP process are relatively low, so numerous contacts between resins and leached ore pulp are needed, which adds to the cost (Merritt, 1971). It is necessary to study methods to reduce process costs.Ultrasound can intensify mass transfer, increase the rate of chemical reactions, and change reaction pathways (Thompson and Doraiswamy, 1999; Luque de Castro and Priego-Capotem, 2007; Adewuyi, 2001; Luque-Garcia and Luque de Castro, 2003). It has great potential in chemistry and is especially considered to be a promising method for enhancing mass-transfer-limited processes, such as ion exchange. Enterzari and Tahmasbi (2009) reported the effect of ultrasound on water softening by ion exchange. Band et al. (1997) proposed a modulated ultrasound application to water desalination with ion-exchange hollow fibers. These reports revealed that ion exchange kinetics could be enhanced by the application of ultrasound. As for hydrometallurgy, Feng and Aldrich (2000) reported that the elution of an ion exchange resin was enhanced by the use of ultrasonication."

Jan 1, 2015

By M. Misra

Improved liberation and flotation of kerogen from eastern oil shale were accomplished with high-temperature grinding and a1 so with the addition of fuel oil during the grinding stage. Liberation measurements indicated that possible coalescence and aggregation phenomenon of kerogen particles during grinding may reflect this behavior. Additionally, ultrasonic treatment of the rougher concentrate prior to cleaning improved the quality of separation.

Jan 1, 1984

By R. Mohan Srivastava

In any operating mine, especially in precious metals operations, immediate improvements in profitability m readily achievable through more effective grade control. Just as the oil industry has come to recognize that enhanced oil recovery (EOR) in existing oil fields yields a higher return on investment than exploring for new oil, so too must the mining industry recognize the benefits of enhanced metal recovery (EMR). Current grade control practices are generally dismal. The very word "control" suggests a willingness to make the best of a bad situation -- as in "damage control" or "disease control" -- and a failure to perceive the opportunities for improved profit. While damage and disease can merely be controlled, success and improved profit can be engineered. This paper presents one approach to enhanced metal recovery. It shows how existing methods can be used to address the issue of ore/waste discrimination. The following sections outline the problem, describe the current state of the practice of grade control, propose an alternative approach and. illustrate the application of the proposed alternative to actual blasthole data from an operating gold mine.

Jan 1, 1992

By Billy W. Parks

This paper reports on the first 2 years in operation of a special-purpose coal handling rig which provides blending, temperature reduction, and continuous, automatic mechanical sampling as part of midstream barge to ship coal transfers. Briefly reviewing some of the characteristics of coal handling peculiar to midstream transfers, the paper discusses how the most beneficial aspects of midstreaming were enhanced through the design of this blending and sampling rig.

Jan 1, 1986

By A. Martin

Detailed porewater profiles of arsenic and other interstitial metabolites were used to assess the relationship between trophic status, sediment redox chemistry and arsenic mobility in a historic tailings repository. The results demonstrate that in eutrophied systems which exhibit greater sediment oxygen demand, the depth of the Fe(III) redoxcline, and hence depth of arsenic release, may lie in close proximity to the sediment-water interface. As a result, arsenic scavenging mechanisms are significantly reduced, resulting in a greater flux of arsenic to the water column. Such considerations have important implications for the management of pit lakes, tailings ponds and contaminated lakes which may consider: 1) the discharge of sewage to the water body during operations; and/or 2) post-closure fertilization as a remediation strategy.

Jan 1, 2002