Search Documents

NICOR Mineral Ventures, Inc. retained Neyer, Tiseo and Hindo, Ltd. to evaluate the potential effects of a planned dewatering operation at NICOR's proposed, 258-acre silica sand mining facility near South Rockwood, Michigan. The ?orebody? is a horizontally extensive, friable, quartz sandstone from the Sylvania Formation which also serves as an aquifer for some of the rural, residential development near the site. We conducted an aquifer test on the site which identified the important aquifer properties. Using these data and an analytical model, we determined that the radius of influence would be expected to range up to 6000 feet from the quarry during its final development stage. An inventory of water supply wells revealed that most wells had sufficient available drawdown and would not be adversely affected. A long-term groundwater monitoring program was recommended to monitor the possible effects at some of the closest wells.

Jan 1, 1987

By T. J. Batchler

"INTRODUCTION A variety of standing supports are being applied in underground coal mining operations to assist in providing stable mine entries. Standing support performance requirements depend on the nature of the ground deformation behavior, and therefore require a good understanding of the interaction between the support and ground to achieve an optimum roof support system. Mining operations often employ standing support strategies that are unique to their mine. A support system that functions successfully in one situation could fail in another situation. It is important that the design and installation of the standing support systems provide the highest probability of preventing roof falls. Considerable research and development has been conducted by support manufacturers to develop standing support technologies for the mining industry. The National Institute for Occupational Safety and Health (NIOSH) researchers, with the cooperation of various support manufacturers, have developed a testing protocol that evaluates performance characteristics of these standing support systems.. Using this protocol, each of these support systems has gone through rigorous safety performance testing under controlled loading conditions in NIOSH’s Mine Roof Simulator (MRS). It is important to understand the unique performance characteristics of each type of standing support. This information allows mine operators to determine if the support system is compatible with the conditions in the mine and to compare each support system and determine if that support will provide equivalent or improved support capability. This paper provides a comprehensive summary of support performance to facilitate this objective. SUPPORT DESIGN CRITERIA AND THE GROUND REACTION CURVE Standing roof support systems are designed to prevent unplanned roof falls. The selection of the standing support is based on the interaction of the support with the surrounding rock mass, and its function is to assist the primary support system in maintaining the integrity of the immediate roof. The standing support works to control the immediate roof structure by resisting deformation that contribute to delamination of the bedded layers and displacements that lead to separation of the bolted zone from stable roof structures above the bolted horizon (Barczak, 2005). Standing supports should be installed early enough and develop sufficient capacity to bring deformation of the ground into equilibrium before a critical deformation is reached that leads to a detached block condition, at which point the standing support will be required to carry the entire dead weight of the detached rock mass to prevent a roof fall from occurring (Mucho, 1999). The ground reaction curve (GRC) can be used to assist in determining the compatibility and design requirements for a support system. It is important to understand the significance of the ground reaction relative to the support design requirements. The ultimate objective is to match the support behavior to the ground response and create equilibrium (stability) of the rock mass. This equilibrium is accomplished when the support loading intersects the ground reaction curve (Figure 1). Essentially, the ground reaction concept implies that the convergence in the mine entry is controlled by the magnitude of the support resistance. However, as a passive support, the standing support develops its loading through convergence. As such, the support needs to maintain its load capacity through the associated deformation of the ground and resulting entry convergence until the equilibrium condition is reached. This requirement causes factors such as the support stiffness, peak capacity, yielding characteristics, and stability to be fundamental to proper support design and application. NIOSH contributes to providing this understanding through full-scale performance testing of support products in the Mine Roof Simulator."

Jan 1, 2017

By V. W. Skema, M. W. Smith

Pennsylvania has 4,000 km (2,500 miles) of streams that do not meet water-quality standards due to acid mine drainage (AMD), making AMD the greatest cause of water pollution in the state. The problem is mainly caused by abandoned coal mines. To abate AMD, Pennsylvania is using a watershed-based approach that includes remining as a key component of a comprehensive restoration strategy. The Tangascootack Creek Water-shed was targeted for AMD restoration through remining. Geologic mapping and overburden data were analyzed using Earth Vision software to identify areas of coal reserves that could be remined to improve water quality. Incentives are offered to encourage mining in these designated areas.

Jan 1, 2002

By M. W. Smith

Pennsylvania has 2500 miles of streams that do not meet water quality standards due to acid mine discharge (AMD), making AMD the greatest cause of water pollution in the state. The problem is mainly caused by abandoned coal mines. Pennsylvania is using a watershed-based approach to abating AMD which includes remining as a key component of a comprehensive restoration strategy. The Tangascootack Creek Watershed was targeted for AMD restoration through remining. Geologic mapping and overburden data were analyzed using Earth Vision software to identify areas of coal reserves which could be remined to improve water quality. Incentives are offered to encourage mining in these designated areas.

Jan 1, 1999

By David J. Herzog

There are two steps in evaluating potential mine waste impacts on ground and surface waters. Characterize the mine waste (characterization methodologies) and assess potential impacts (assessment strategies). One or both may be required for mine permitting, operation and closure. The first step is to characterize the waste. Determine if it has the potential to release chemical constituents or acid rock drainage to the environment. If no potential exists for release to the environment, the evaluation process is complete. A monitoring plan is then established. If the potential exists for release of chemical constituents or acid rock drainage to the environment, a strategy to evaluate potential impacts must be implemented. Strategies discussed here to evaluate potential impacts were developed during investigations at precious metal and base metal mines in Nevada. Water resources in Nevada consist mostly of ground water. So the strategies discussed focus on potential impacts to ground water. However, several of these strategies also apply to assessing potential impacts to surface water. Implementing these strategies has helped determine the potential for impact and has been successful in permitting mine expansion as well as allowing continued operation and obtaining mine closure at several mine sites in Nevada. These strategies were carried out in accordance with Nevada Division of Environmental Protection (NDEP) regulations and through the National Environmental Policy Act (NEPA)

Jan 1, 1995

By M. Rosenshine, R. W. Barbaro

This paper presents a cyclic queueing model that evaluates the productivity of a shovel-truck materials haulage system. For a cyclic queueing problem with exponentially distributed service times, a cyclic queueing model provides exact solutions in a fraction of the time that simulation takes to produce an approximate solution. The model is applied to an example problem, and the results are validated with simulation. Simulation is used to show that the assumption of exponentially distributed service times and steady state are not serious problems. A cyclic queueing model can be used to quickly obtain an accurate assessment of the productivity of a shovel-truck system.

Jan 1, 1988

By Ralph W. Barbaro

This paper presents a cyclic queueing model which evaluates the productivity of a shovel-truck materials haulage system. For a cyclic queueing problem with exponentially distributed service times, a cyclic queueing model provides exact solutions in a fraction of the time that simulation takes to produce an approximate solution. The model is applied to an example problem, and the results are validated with simulation. Simulation is used to show that the assumptions of exponentially distributed service times and steady-state are not serious problems. A cyclic queueing model can be used to quickly obtain an accurate assessment of the productivity of a shovel-truck system.

Jan 1, 1986

By T. O. Dauda, L. O. Ojo

One of the results of the Earth summit (The United Nations Conference) on Environment and Development - UNDP is the statement of forest principles. Others include: the Rio Declaration which is that the human beings are entitled to a healthy and productive life in harmony with nature; Agenda 21-for achieving sustainable development in the 21st century; the convention on biological diversity and the frame work convention on climate change. In the preservation of the biological diversity, Government at various levels took series of steps such as legislation, establishment of forest reserves including strict nature reserves, Forest guards, afforestation projects and others. Omo Forest Reserves is one of the Forest reserves owned by the Ogun state Government of Nigeria. It houses the Omo Biosphere Reserve (that is Strict Nature Reserve of International standard). This biosphere reserve is surrounded by buffer zones, which are meant to serves as protection for the biosphere reserves against encroachments. This study showed that the richest plot in term of species composition (that is plot 15 with the species frequency of 123) is almost the least diverse (with Simpson diversity index of 0.9127 which is 0.0238 higher than the least). It could also be established from this study that the diameter size class of trees with the highest frequencies are the lower size classes (5cm-10cm and 10cm -20cm). These results revealed a magnanimous encroachment on the buffer zones, which is an indication of bad status for the Biosphere Reserves as well as against the spirit of the sustainable use of the natural resources.

Jan 1, 2005

By Dani Delaloye, Kas Zurek

Evaluating and selecting the appropriate excavation method is a key to the success of any tunnelling project. The benefits and risks of different methods should be well understood by the designer and communicated to the project owner to enable selection of a preferred method from a technical, social and environmental impact, cost and constructability perspective. For tunnels that have an internal diameter around 3 m, depending on the tunnel purpose and ground conditions, both microtunnelling with pipe jacking and tunnel boring machine excavation with a one- or two-pass lining may be feasible construction methods. Using the Ferry Road and Riverbend Combined Sewer Relief Project located in Winnipeg, MB as a case study, this paper will discuss the benefits and drawbacks of each method, including technical design, social, environmental, cost, schedule, and risk considerations.

Jun 13, 2023

By J. M. Wempen

As development in underground coal mines progresses away from the critical components of the ventilation system, including the main fans and ventilation shafts, resistance within the system is markedly increased. This results in higher pressure and flow requirements from the main fan(s) to maintain adequate face ventilation. Upgrades to the primary ventilation system are often required. The use of booster fans underground is a potentially practical alternative to the addition of shafts and surface fans. This study presents simulations of the use of booster fans in two underground ventilation scenarios, one longwall and one room-and-pillar. The booster fan effects on the power requirements of the ventilation systems are evaluated.

Jan 1, 2011

By J. M. Wempen

As development in underground coal mines progresses away from the critical components of the ventilation system, including the main fans and ventilation shafts, resistance is markedly increased. This results in higher pressure and flow requirements from the main fan(s) to maintain adequate face ventilation, which often requires that the primary ventilation system is upgraded with additional shafts and surface fans. The use of booster fans underground is a potentially practical alternative. This study presents simulations of the use of booster fans in two underground ventilation scenarios, one longwall and one room and pillar. The booster fan effects on the power requirements of the ventilation systems are evaluated.

Jan 1, 2011

By F. N. Kissell

The US Bureau of Mines undertook a study of those factors influencing worker escape from an outby coal mine fire. The results of this investigation were two-fold. First, those factors affecting escape from a mine fire were defined, and second, the relationships between these factors were identified. Although the individual components had been studied before, little information was available on their interdependence. Fault tree analysis was used to evaluate the miner escape scenario. After constructing the fault tree, a two-phase analysis of the tree was conducted. During the first phase, the minimal cutsets of the fault tree were identified and ranked. These sets were the smallest sequence of events leading to fatalities during the fire. This ranking revealed that reduced evacuation delays, improved self-rescuer training, and improved stopping construction were important in controlling fatalities during escape from the mine fire. The second phase involved additional analyses of the fault tree. These evaluations were started by first determining occurrence probabilities for each event in the fault tree. Two types of sensitivity analyses were then conducted. The first analysis dealt with changes in event probabilities and their impact on the likelihood of fatalities. The final sensitivity analysis considered dramatic reductions in the probability of fire fatalities. This revealed what event probability values were necessary to reach this level. These results have revealed various remedial actions that could be used to improve the survivability of an outby mine fire.

Jan 1, 1990

By S. K. Oraee

Managers always look for systems with minimum hazards. The hazards create problems for performance of projects. The largest and most important hazards of working underground mine can be related to health, safety and environmental, because if one of these sectors be in hazard, maybe lead to close mine. Failure mode and effects analysis (FMEA) is a widely used quality improvement tool to identify the potential failure modes for measuring reliability of a product or a process. FMEA is performed by developing a risk priority number (RPN), which is the product of severity, occurrence, and detection ratings. On the other hand, with regard to uncertainty in the decision-making, fuzzy theory will be able to model this uncertainty. Fuzzy FMEA provides a tool that can work in a better way with vague concepts and without sufficient information than conventional FMEA. This article by using Fuzzy FMEA and based on HSE criteria evaluate hazards of Parvade No. 1 Mine in Tabas Coal Mine. The results demonstrate the most hazardous parameter is rock burst in this mine.

Jan 1, 2011

By J. P. Rider

The number of extended cut mining systems has increased significantly in coal mines over the last decade, and there is a constant push to extend the face ventilation systems to even greater setback distances. The need to maintain airflow at setback distances of12.2 m (40 ft) and beyond requires that methods for delivering intake air to the face be improved, or alternative ventilation techniques be implemented. The emphasis of this research effort was to examine various techniques to improve the distribution of available air at the mining face in order to reduce face methane levels. A study was conducted comparing the performance of a jet fan, used in conjunction with a machine mounted scrubber, with blowing curtain ventilation in a 27.5 m (90 ft) heading. In addition, a second study was performed on blowing curtain systems examining how scrubber flow, intake air velocity, and curtain setback influence face methane concentrations. Results showed that when the heading advances to a depth of 27.5 m (90 ft) blowing curtain systems were more efficient at diluting face methane levels when compared to a jet fan. Also, increases in scrubber flows and curtain velocity resulted in lower face methane concentrations for blowing curtain systems at 9.2 and 15.2 m (30 and 50 ft) setbacks.

Jan 1, 1997

By J. P. Rider

The number of extended cut mining systems has increased significantly in coal mines over the last decade, and there is a constant push to extend the face ventilation systems to even greater setback distances. The need to maintain airflow at setback distances of 12.2 m (40 ft) and beyond requires that methods for delivering intake air to the face be improved, or alternative ventilation techniques be implemented. The emphasis of this research effort was to examine various techniques to improve the distribution of available air at the mining face in order to reduce face methane levels. A study was conducted comparing the performance of a jet fan, used in conjunction with a machine mounted scrubber, with blowing curtain ventilation in a 27.5 m (90 ft) heading. In addition, a second study was performed on blowing curtain systems examining how scrubber flow, intake air velocity, and curtain setback influence face methane concentrations. Results showed that when the heading advances to a depth of 27.5 m (90 ft) blowing curtain systems were more efficient at diluting face methane levels when compared to a jet fan. Also, increases in scrubber flows and curtain velocity resulted in lower face methane concentrations for blowing curtain systems at 9.2 and 15.2 m (30 and 50 ft) setbacks.

Feb 24, 1997

By F. N. Kissell

The Bureau of Mines used sulfur hexafluoride (SF6) tracer gas to evaluate the effectiveness of gob ventilation and/or sealing practices at three coal mines, each having different problems associated with their mined-out areas. The purpose of these ventilation studies was to better understand whether current techniques employed for ventilation or sealing are successful at minimizing the potential for gob fires and explosions. The work performed at each mine is discussed: One is a longwall operation that uses ventilation to carry off hazardous gases, and two are room-and-pillar operations, each with far different concerns, that seal off the gobs to isolate them from the main mine ventilation. In all cases, employment of the Bureau's SF6 tracer gas technique resulted in answers to questions raised by the mine operators concerning the effectiveness of their gob ventilation or sealing practices in preventing mine fires.

Jan 1, 1987

By T. Stack, C. Roos, M. Drake, P. Conrad

"This paper presents the evaluation Montana Tech completed for the Western Energy Company Rosebud Mine relating to the benefits of survey data collected using novel technologies over traditional methods for topographic surveys. These technologies include Unmanned Aircraft Systems (UAS), photogrammetry, and laser scanning/LIDAR. Utilizing these technologies, large areas such as reclamation areas and cast blasts can be surveyed in a timely manner for use by the mining operation. The areas that were evaluated were the improvements in the safety of employees and the time required to collect data. In addition, there is also a potential cost savings for the operation, all while not affecting the accuracy of the data that is collected. PROJECT BACKGROUND Accurate topographic survey data is critical to successful surface mining operations. It is used for mine planning and design as well as permit compliance. Currently, employees typically collect survey data using GPS equipment or total stations. These methods can be dangerous, as they require employees to work near large operating mobile equipment, edge of high walls, and on piles of stacked steep-sloped loose material. Aerial and satellite photographs, performed by a contractor, can be used to obtain some of this information, but it is expensive and may not be attainable during overcast conditions. Montana Tech, along with the Rosebud Mine, conducted research on the accuracy, cost, and other benefits of survey data collected using novel technologies. Some of the methods studied include, but are not limited to, Unmanned Aerial Systems (UAS) or Vehicles (UAV), photogrammetry, and laser scanning. These methods were evaluated to determine if these technologies provide mining companies with a safer, cost effective, and accurate method to collect data for surface mining operations. The project scope was to evaluate various surveying techniques to determine which techniques would be applicable for the Rosebud Mine and complete a trade-off study comparing the new techniques with currently used methods. The trade-off study included an analysis of the technological differences between the methods, safety and legal considerations for the new techniques, operational limits, and the costs associated with each technique. Working with the Rosebud Mine team, techniques were selected for field trial and accuracy comparison. This paper presents a literature review of applicable technical papers and a summary of the Federal Aviation Administration regulations for UAS, followed by a study comparing conventional GPS topographic surveys with UAS based systems and laser scanning systems. The comparison of the various methods was broken into the following four categories: operator safety analysis, time comparison, survey accuracy, and cost analysis. After all of these portions of comparison were completed a recommendation was provided based on the evaluation that was performed."

Jan 1, 2017

By Mehmet Mesutoglu, Ihsan Ozkan

This study investigates the feasibility of rock bolting support in an underground coal mine gallery with a thick coal seam. The Ömerler underground coal mine working area, owned by West Lignite Enterprise of Turkish Coal Enterprises, was selected for this purpose. Longwall top coal caving is implemented as the production method in the Ömerler underground coal mine. Field and laboratory studies were conducted to determine rock mass and rock material properties, followed by experimental, empirical and numerical analyses based on the acquired data. The obtained design results were evaluated using a resin-grouted rebar rock bolting (RBR) system and steel arch support (SAS) pilot application areas. The numerical modeling results conducted using the fast Lagrangian analysis of the Continua 3D (FLAC 3D v6.0) program indicated less displacement and secondary stress change in the RBR-supported zone compared to the SAS-supported zone. In situ measurements also demonstrated that RBR provided more successful support to the roof during coal production activities. The findings suggest that RBR is a more effective solution when evaluating the feasibility of rock bolting support systems in underground galleries with thick coal seams at the Ömerler Mine. This study emphasizes the importance of more sustainable and safe support systems to enhance operational efficiency in the coal mining industry.

Mar 1, 2025

By Stan Tang, Yiming Sun, S. Amir Reza Beyabanaki, N. Sathi Sathialingam

The Kurve mixed-use development project including a 22-story tower at 2801 Sunset Place was constructed on a site consisting of a roughly rectangular-shaped lot at the intersection of Wilshire Boulevard and Hoover Street in Los Angeles. Two Metro Red Line tunnels, with depths of approximately 30 feet and 58 feet, respectively, cross below the building at distances of approximately 1 foot to over 63 feet from the site. This paper presents numerical modeling performed to evaluate the ground and tunnel behavior in response to building construction. Results of geotechnical instrumentation and monitoring undertaken during the building construction are also discussed.

Jun 13, 2023

By Martin B. Hudson, John Yao, Matthew R. Crow, Yiming Sun, John T. Waggoner, Roozbeh Geraili Mikola

"The Wilshire Grand redevelopment project in downtown Los Angeles includes construction of a new 73-story tower. Construction required excavation up to 93 feet deep (28 m). The south side of the excavation, up to 57 feet deep (17 m), required placement of shoring within about 6 to 10 feet (1.8 to 3.0 m) horizontally away from a 400-foot-long (122 m) section of one of the existing Los Angeles Metro Red Line twin subway tunnels. These tunnels were constructed using a 22-foot-diameter (6.7 m) digger shield, and were initially supported with expanded, precast concrete segments, with final cast-in-place reinforced concrete lining. The temporary shoring system for the deep excavation consisted of soldier piles generally spaced at 8 feet (2.4 m) on center with multiple levels of tieback anchors extending above the subway tunnels. The lowest level of bracing consisted of rakers supporting walers attached to the soldier beams because installation of tieback anchors at that level would conflict with the tunnels. Numerical analyses were performed to predict tunnel movement caused by the excavation and its effects on the train operations. This paper describes the numerical modeling, tunnel and geotechnical instrumentation and monitoring program, and comparison of the computed and observed tunnel responses to the deep excavation and tower construction. With increasing urban redevelopment in major cities, the project is a valuable case history for excavation adjacent to existing tunnels. INTRODUCTION The Wilshire Grand redevelopment project includes the demolition of a 16-story hotel built in the early 1950s and the construction of a new 73-story tower in downtown Los Angeles (LA) that will be the tallest building in the western United States. The project site is situated on approximately 2.7 acres (1.1 Ha) of land bounded by Figueroa Street to the east, Wilshire Boulevard to the north, Francisco Street to the west, and 7th Street to the south (see Figure 1a). The new tower is being constructed by Turner Construction for Hanjin International Corporation. Construction of the basement and foundation of the new tower required excavation up to 93 feet (28 m) deep. Shoring was designed by Cefali & Associates and installed by Malcolm Drilling Company. Along 7th Street, an excavation up to 57 feet (17 m) deep required shoring to be installed within about 6 to 10 feet (1.8 to 3.0 m) horizontally from an existing 400-foot long (122 m) section of one of the LA Metro Red Line subway tunnels (see Figure 1b). The tunnels, extending from the 7th/Metro Station to the Westlake-MacArthur Station, were constructed in the late 1980s and early 1990s with an excavated diameter of approximately 22 feet (6.7 m). They were initially supported with expanded, precast concrete segments with a final cast-in-place reinforced concrete lining. The existing hotel was demolished in 2012 and 2013, with shoring installation and excavation for the new basement occurring as the demolition occurred. At the time of writing, January 2016, the structure of the building adjacent to the tunnels is largely complete."

Jan 1, 2016