Search Documents

By Robert A. Pimentel

Dust is still a major problem in increasing production from longwall faces. Over the last decade, significant improvements have been made in the development of techniques for reducing dust exposure on conventional and continuous sections. But virtually no improvements have been made in dust control on longwall sections. It is true, that there are many more continuous mining sections than longwall sections in the United States and that the number of workers overexposed on continuous miner sections is much larger than the number on longwall sections. However, the problem on continuous miner sections appears much easier to solve and, in fact, we believe that the techniques are available to get virtually all continuous miner sections in compliance. The problems on longwall sections are much more elusive. Also, the number of longwall sections in the United States is expected to increase during the 1980's. Thus, dust control on longwall sections remains a formidable and important problem. Companies operating longwall sections with a dust problem are faced with the tasks of having to quantify the various dust sources, of selecting proper techniques to reduce the problem, of implementing the techniques and of evaluating their effectiveness.

Jan 1, 1983

By Mike Amick

As virgin coal reserves dwindle, more and more mines are being opened in areas with previous mining. As addressed in this conference before, there are solutions available for designing mines extracting coal from reserves with known underground workings above or below the target seam. Often times, however, mining begins with limited knowledge of the underground workings. Even with careful planning, the proposed design has limited success because the ?facts? as presented during planning turn out not to be as accurate as one would like. At National Coal?s Mine #14, mining the Walnut Mountain seam, after driving the main entries in some 34 crosscuts, it was found during routine mine examinations that the pillars had separated from the roof in a few areas of the mains. Immediate roof conditions proved to be sound but questions arose concerning the stability of the main roof and floor. Core tests were done to better determine the rock strengths and characteristics. The paper presents the ideology used to tackle the effects of mining over old works in an operating coal mine. This paper discusses the analysis of the symptoms observed and the steps taken to ensure that this pillar separation was caused by the underlying old workings and that the separation was expected and controllable.

Jan 1, 2009

By R. C. Ford, J. Kelsey, S. A. Pierce, M. D. Ankeny

Evaluation of acid drainage risk from spent (leached) ore in arid climatic zones consists of two components: (1) whether residual and secondary minerals will release acid and metals when exposed to rainfall, and (2) whether ambient rainfall is likely to infiltrate, and eventually impact surface or ground water resources. The risk of acid drainage from spent ore at the El Abra on-off copper leach pad operation was evaluated using conventional geochemical methods and unsaturated flow models. Although geochemical testing indicated poor quality water would result from any seepage, unsaturated flow modeling demonstrated that infiltration and seepage were unlikely given the arid climatic conditions. Modeling further demonstrated that the residual moisture content of the spent ore when it is removed from the leach pad controls the risk of seepage. To further reduce the risk of seepage, operational controls were developed and implemented at the El Abra site.

Jan 1, 2000

By Judson H. Whitman

To evaluate intelligently and to market a source of rare earth raw material, it is necessary that the producer understand the requirements of the processor and the manner in which these requirements effect the value and salability of his product. This paper will be an attempt to aid in such an understanding. The majority of rare earth processors are primarily chemical companies, not mining or metallurgical companies, as the complexities of the processing procedures are' much more chemical in nature than metallurgical. The rare earths and the rare earth industry are normally divided into two groups - the ?light? or cerium group and the ?heavy? or yttrium group. They are so named because cerium and yttrium are the most common elements in 'heir respective groups and are so divided on the basis of mineralogical and chemical characteristics. The dividing line of the two groups is not rigidly fixed but usually is considered as being between samarium (atomic number 62) and europium (atomic number 63). Although the two groups are quite similar, processing procedures differ significantly, hence most processors tend to specialize in one group or the other. There is, however, a growing tendency toward participation in both groups.

Jan 1, 1960

By R. F. Davis

The evaluation and selection of coals for producing metallurgical coke is indeed a com- plex process simply because coal is a complex and variable substance which is sensitive to how it is treated from the time it is mined until it is transformed into coke. A review of the the more common evaluation tests made on coal and how the test results are applied in commercial practice. Parameters used to select coal blends for wet and preheated charges should also be of interest.

Jan 1, 1980

By Steve Garcia

GEORGE WEINMAN: Our next speaker is Steve Garcia, operations vice president and general manager of mining at IMC-Agrico, Florida. Steve was born in Lakeland, Florida, to an IMC mining family. He has 17 years with IMC-Agrico and Freeport companies, including assignments in North Carolina, Nevada, Arkansas, and Indonesia. His work within the industry includes technical and operating positions including chief metallurgist, drying superintendent, and mines operations manager at Pane Creek. Other experiences include design of a grassroots phosphate facility in North Carolina; construction and start-up of a gold facility near Elko, Nevada; work in the Blytheville, Arkansas, ammonia urea facility; and three years managing engineering, construction, and support services in Irian Jaya, Indonesia. Steve's presentation is "Evaluation and Standardization of Multiple Slurry Pumping Systems."

Jan 1, 1998

By C. P. Wa1ters

This paper is written primarily from the standpoint of the miner and consumer of Missouri fireclays in refractory products, principally firebrick used in the linings of blast furnaces, hot metal transfer cars, the recuperators of glass melting tanks, and other allied uses involving contact with liquid metals and reactive slags. For these uses the manufacturing plant requires forecast of certain physical characteristics, as well as chemical characteristics, of the raw clays as a determination of practicability of mining, treatment such as pre -firing or calcining, and final usage area. These methods and results may leave something to be desired from an academic view, but are used my operation as an on-running guide to seeking and mining raw material. The high quality fireclays of Missouri are generally differentiated by the user as the softer, somewhat plastic, "bond" clays and the so-called flint clays suitable for a fired or unfired aggregate portion of a brick composition. The semi-plastic "bond" clays are mined in a producing area of northeast Missouri including Montgomery, Audrain, Callaway, Monroe, and Lincoln counties. In this geographic area the clays are the members of the cheltenham formation and occur in rather large lenses in which the usable members may approach 15 meters in thickness and an area of 6o to 8o acres. Overburden is dependent on the surface topography and, in our operations, varies from 8 meters to 25 meters. It can be up to 36 meters in the prairie uplands, but this is rarely strip mined. There was former mining by shaft and drift methods in which the overlying coal was also worked. These clays are primarily used as a binding material for other clay aggregates and is characterized by its lower refractoriness-cone 3o (165o c) to cone 321/2 (172o c), in terms of pyrometric cone equivalent, and an alumina - Al2o3 - content of plus or minus 31%. Physically, these clays are readily slaked by water to a fine grain size and exhibit a degree of

Jan 1, 1977

By Andreas Eberhorn

The evaluation criteria for cost comparison of the Gearless Drive, also called Ringmotor or wrap-around motor, as variable-speed drive with a Twin Drive System using synchronous motors are reviewed. Both mechanical and electrical components of the drive system are considered. The evaluation criteria are described and for the cost comparison the applicable method is demonstrated. The cost comparison is based on a medium and large sized mill system. Each drive package will display cost details with regard to capital cost, maintenance, power losses, overall efficiency, overhead and loss of production. As conclusion the benefits and disadvantages of the two drive/mill packages will be presented together with a payback diagram.

Jan 1, 1996

By Raj K. Singhal

This paper is a report on a task force study dealing with many facets of computerization. The primary mandate of the task force was to examine the software and hardware currently available for application relating to reserve estimation, mine planning, economic evaluation, equipment selection, production scheduling and composite mine simulation and to evaluate how adequately the software fulfills the user needs in surface mining of oil sands and coal. To meet its objectives the task force consulted extensively with the users, developers and suppliers of hardware and software. The paper outlines the approach taken by the task force to fulfill its mandate, summarizes its findings and presents some pointers which might be useful to others considering this type of evaluation.

Jan 1, 1986

By QINGXIANG CAI, Lin Li, PENG LIU, IZHAR MITHAL JISKANI, XIANG LU, Wei Zhou, YONGLI ZHOU

Green mining is the latest technological advancement to reduce mining’s environmental impact with minimal energy and resource consumption. Green mining — aimed at protecting nature and providing socio-economic benefits — is a multifaceted network of its connotations and key indicators. China has not yet defined its connotation and formed an effective evaluation system for surface mining. We defined its connotation and developed an evaluation index system based on the theory of green grades. As the indicators are selected based on extensive research, they express the advantages and disadvantages of various aspects of a mine. The index is composed of three attributes (safety, efficiency and environment), nine criteria and 35 indicators. The indicators were quantified according to experts’ opinions using the fuzzy comprehensive evaluation method. The results of a case study show that the environment is the most critical aspect, followed by efficiency and safety. This study can provide technical support for the development of green mining.

By QINGXIANG CAI, Lin Li, PENG LIU, IZHAR MITHAL JISKANI, XIANG LU, Wei Zhou, YONGLI ZHOU

The concept of green mining is to improve the mining industry in a holistic way so that it is safe, efficient, and environmentally sustainable. The purpose of this study was to develop an evaluation index system of green surface mining based on the theory of green grades. The evaluation model is comprised of three attributes (safety, efficiency, and environment), nine criteria, and 35 indicators. The fuzzy comprehensive evaluation method was used to determine the weights of indicators by taking into consideration degree centrality, closeness centrality, and betweenness centrality. Findings indicate that the environment is the most critical aspect of green surface mining, followed by efficiency and safety. The top five ranked green mining success indicators were the application of new technology, starting-off-rate of equipment, science and technology input to total investment, the number of accidents (decreased), and the production (increased). It was observed that more improvements are needed to overcome water, air, waste, and sound pollution. Attention should also be paid to land reclamation and post-mining land uses, which are key factors in green mining. The proposed model can be applied to evaluate and improve the level of green surface mining in other regions. This study provides a tool for decision-makers that can offer technical assistance to green mining.

May 26, 2020

By Vasiliki Founta, Andrew J. Whittle

"This paper describes the development of a 3D finite element model for predicting ground movements caused by construction of 7.1 m diameter twin bored tunnels for the Crossrail project in London using Earth Pressure Balance (EPB) machines. The model uses the commercial FE code, Plaxis 3D, to represent the face pressure, conical shield, grouting process and activation of precast segmental concrete lining systems through a set of boundary conditions that advance through the soil mass along a prescribed trajectory. Soil behavior is described using the Mohr-Coulomb soil model with input parameters calibrated from laboratory element tests. The analyses focus on the performance of the EPB tunneling machines in greenfield conditions beneath Hyde Park, where the tunneling occurs within deep layers of relatively uniform London Clay. The model predictions are in good agreement with surface and sub-surface vertical settlements measured at a well-instrumented section, but tend to overestimate the measured lateral displacements towards the tunnel. Ongoing studies are focused on the role of soil behavior and the approximations in FE model predictions of tunnel-induced ground deformations. Introduction Since their introduction in the 1970’s, closed-face Earth Pressure Balance (EPB) machines have become widely used for soft ground tunnel construction. The EPB design relies on a screw conveyor system to regulate the pressure of the excavated soil/spoil within the head chamber and hence control stability at the face of the machine. One of the key design issues in the application of EPB machines is to establish how control parameters, including the advance rate, face pressure and grouting processes (used to compensate for the tail void at the rear of the shield and to infill gaps between the precast lining rings and surrounding soil) affect and/or control the far-field ground movements. For closed-face systems, short-term deformations are associated with ground losses at the face, overcutting and ploughing of the shield and poor control of grouting in the tail void; while long-term deformations can occur due to consolidation and creep within the surrounding soil (and are closely connected to the seepage boundary conditions;e.g., Laver & Soga, 2012). The control parameters for advancing the EPB machine can have a significant effect on the magnitude and distribution of the far-field deformations. Therefore, analyses of the ground response to tunneling require accurate modeling of the soil stratigraphy and constitutive behavior as well as the construction process. Finite element (FE) methods have been used to simulate tunnel construction since the early 1980s, but only a few studies involved three-dimensional modelling of mechanized tunneling (e.g., Finno and Clough 1985; Bernat and Cambou 1999; Swoboda and Abu-Krisha 1999; Dias et.al. 2000; Melis et.al. 2002; Kasper and Meschke 2004; Möller 2006). In order to get a better understanding of the effect of the construction process and soil properties on the development of the ground deformations more comprehensive models of tunnel excavation and tunnel support are required in order to capture the 3D nature of mechanized tunneling and the effect of construction parameters such as advance rate, face and grout pressure."

Jan 1, 2016

By W. Addy Majewski, Kenneth L. Bickel

The U.S. Bureau of Mines (USBM) and Diesel Controls Limited evaluated a new diesel emission control system on an underground mine vehicle. The system was a catalyzed ceramic wall-flow diesel particulate filter (CDPF) combined with an catalytic converter, or diesel oxidation catalyst (DOC). This paper describes the design and installation of the system on a load-haul-dump (LHD). The results of screening tests conducted by the USBM are also given. The screening tests were conducted to determine if the device's particulate collection efficiency, regeneration temperature, and effect on gaseous hydrocarbon (HC) and carbon monoxide (CO) emissions changed over the period it was being used. The system was removed from the LHD and evaluated in the laboratory after operating for 308 and 1200 hours. After 308 hours of operation, laboratory testing revealed its particulate collection efficiency varied from 41.0 to 93.5 percent, depending on engine operating conditions. Its regeneration temperature was about 415° C. It reduced HC emissions by up to 97.6 percent, and CO by up to 95.0 percent. When tested in the laboratory after operating for 1200 hours on the vehicle, no significant change in performance was observed.

Jan 1, 1995

By J. D. Miller, C. L. Lin

The appropriate software and hardware necessary to adapt an X-ray CT analyzer for the determination of coal washability was developed and successfully tested for well-characterized samples under laboratory conditions. Evaluation of the CT-based analyzer under simulated on-line conditions is also presented to verify the on-line capabilities of the newly developed X-ray CT analyzer for the control of coarse coal cleaning circuits. The investigation shows that the data obtained from CT washability analyses compare favorably with experimental sink float data. Further, image frequency was considered to evaluate the CT-Based coal washability analyzer for simulated on-line conditions. Specifically, the number of observations (image spacing) needed for accurate sampling and the total time required to perform the calculations for a representative data set were determined. Key words: Coal washability, Computer simulation, X-ray CT analysis

Jan 1, 2003

By L. Patts, J. Hummer

The use of diesel-powered equipment in underground coal mines has increased substantially during the last ten years in an effort to enhance mine safety and productivity. Pennsylvania and West Virginia are two of a number of states with regulations governing the use of such equipment. These states both developed and promulgated regulations before permitting diesel equipment in their underground coal mines because of concern for miners’ safety and health, especially with regard to the contamination of mine ventilation air with diesel exhaust emissions. The major components of diesel exhaust emissions are combustion gases and diesel particulate matter. The gaseous emissions consist of carbon monoxide, carbon dioxide, oxides of nitrogen, sulfur oxides and unburned hydrocarbons. The diesel particulate matter (DPM) is comprised of solid carbon particles, liquid and solid hydrocarbons, sulfates and moisture. The Federal Mine Safety and Health Administration (MSHA) also promulgated regulations in an effort to control diesel emissions in underground coal mines. MSHA has adopted threshold limit values (TLVs) for all gaseous components of diesel exhaust, which were established by the American Conference of Governmental Industrial Hygienists (ACGIH). MSHA (30 CFR Part 72 Subpart D) has established a tailpipe DPM emissions limit of 2.5 g/hr for diesel engines used in permissible equipment, heavy-duty non-permissible equipment, generators and compressors used in underground coal mines. A tailpipe DPM limit of 5.0 g/hr has been established for light-duty outby diesel-powered equipment. The rationale for the tailpipe emissions limit was that an ambient measurement of DPM in a coal mine was not feasible because there is no established sampling method able to distinguish between coal mine dust and DPM. The stringent tailpipe emissions limit mandates the use of exhaust aftertreatment devices for most diesel engines used in underground coal mines today. One method by which tailpipe DPM can be reduced to MSHA limits involves using an exhaust cooling device in conjunction with a high-temperature, disposable diesel particulate filter.

Jan 1, 2011

By A. L. Putz, G. Ladouceur, A. R. Laplante

A laboratory centrifugal concentrator was used to evaluate two gravity circuit configurations treating a flash flotation concentrate at a Canadian gold mill. The Initial circuit consisted of a 76 cm (30 Inch) plant Knelson Concentrator (PKC) for coarse gold removal. Later, a hydroseparator and spiral were Installed, with the hydroseparator underflow feeding the spiral and the spiral tailings plus hydroseparator overfiow reporting to a 51 cm (20 Inch) PKC. Gold recovery In the 76 cm PKC averaged 45%. Gold was recovered consistently In all size fractions greater than 38 µm, where recovery dropped to 22% for the -38 µm material. Changing the circuit to Include the hydroseparator and spiral decreased the Knelson unit recovery to less than 17%. The decrease was attributed to the spiral which recovered much of the free gold ahead of the Knelson and to changes In the mill feed (free gold portions were finer and less abundant). The spiral demonstrated erratic behaviour although It still recovered significant coarse gold (+75 µm) yielding unit recoveries of 18-44%. Although mechanical difficulties were experienced with the 76 cm PKC, Its performance was superior to that of the hydroseparator, spiral and 51 cm PKC configuration. Much of the gold In the ball mill recirculating load was found to be too coarse for significant recovery In the flash flotation cell and should be recovered by gravity from the cyclone underflow or ball mill discharge. The LKC proved to be a successful device to evaluate gravity recoverable gold content. Dilution of test samples with silica further enhanced this methodology.

Jan 1, 1993

By F. C. Appleyard

As one of the more important Industrials Minerals, gypsum occupies a significant place in the economy of the United States, particularly in that segment which can be loosely called the Construction Industry. For many years, products made from gypsum have been a major building material, and the usefulness and versatility of these products is such that their widespread use is expected to continue. In 1968, according to U.S. Bureau of Mines statistics, the value of all gypsum products sold in the United States was 405,000,000 - and although this value has dipped from the 1964 high of $ 432,000,000, it is expected to trend upward in the next few years to equal and surpass this figure as the construction industry recovers from its current squeeze of "tight money" and high interest rates. There are many factors to be measured in determining the potential value of any mineral deposit, and how it might fit within its particular industry. What, then, are the qualities which a gypsum deposit must have in order to profitably participate in the four hundred million dollar plus business which is the gypsum industry? First let's consider the geology of gypsum, the geographic distribution of deposits, and the more important factors such as size, grade, capital requirements, and operating cost. Then, an understanding of the uses of gypsum, various types of products, and location of markets would be helpful, along with such other factors as the structure of the industry, price trends, etc.

Jan 1, 1970

By Harold E. Goetzman, Blair R. Benner, Shaolin Zhong, Rodney L. Bleifuss

A commercial high pressure roller press (KHD 90125) was installed at the Coleraine Minerals Research Laboratory for testing in October, 1994. Pilot plant evaluation of the high pressure roller press has shown that it can be used as an alternative to the rod mill for the comminution of taconite. A series of pilot plant tests were run to compare roller press products to rod mill products in a simulated taconite flowsheet using magnet separation and closed circuit ball milling. Further investigation of a hybrid grinding system, roller press crushing followed by ball mill grinding, indicate that the combination may represent the most energy efficient system for taconite processing.

Jan 1, 1998

By M. L. Young, M. S. Klima

Hindered-settling columns are used throughout the minerals industry for both size and density separations. In this study, the performance of a continuous laboratory-scale hindered-settling column was evaluated for various particle systems. The test variables included solids composition, water rate and column height. Column performance was evaluated using partition curves and corresponding performance parameters.

Jan 1, 2000

By M. L. Young

Hindered settling columns are used throughout the minerals industry for both size and density separations. In this study, the performance of a continuous, laboratory-scale hindered-settling column was evaluated for various particle systems. The test variables included solids composition, water rate, and column height column performance was evaluated using partition curves and corresponding performance parameters.

Jan 1, 1999