Search Documents

By S. Mischler, J. Noll, G. Schnakenberg, A. Bugarski, M. Crum

Diesel particulate filter (DPF) systems and biodiesel fuels are two of the most promising technologies available to the mining industry to reduce the exposure of underground miners to diesel particulate matter (DPM). A study has been conducted to estimate the potential of DPF systems and biodiesel blends to reduce DPM emissions from production vehicles. Results of testing three DPF systems in an isolated zone showed 88% to 99% reductions in elemental carbon concentrations. The test results also show that biodiesel blends, B20 and B50, reduced the elemental carbon concentrations in the mine air by 26 and 48 percent, respectively.

Jan 1, 2004

By L. Yuan, J. H. Rowland, R. A. Thomas

"Hydrogen (H2) gas released during battery charging can result in cross-interference for carbon monoxide (CO) sensors used for early fire detection and compromise the integrity of the mine atmospheric monitoring system (AMS). In this study, a series of laboratory-scale and full-scale experiments were conducted to evaluate the responses of different CO sensors to H2 gas. In the laboratory-scale experiments, constant H2 concentrations in the airflow, from 100 to 500 ppm, pass through sensors. While in the full-scale experiments, increasing H2 concentrations generated as a byproduct from charging the batteries at the battery charging station rise to the sensors under different ventilation scenarios. The H2 concentrations at the CO sensor location were measured using H2 sensors and were correlated with the CO sensor response. The effects of ventilation and sensor location on the CO sensors responses were also analyzed. The results of this study can help mining companies to select appropriate CO sensors and improve the deployment of these sensors to ensure the safeguard of underground miners. INTRODUCTION As many types of battery-powered mining equipment such as scoops and shield haulers are used in underground mining operations, charging stations are required to charge the equipment batteries. These batteries are of lead acid chemistry. A safety issue exists with the battery charging stations as all lead acid batteries produce flammable H2 gas during the normal charging process. Overcharging or excessive heat can quickly cause batteries to produce even more H2. If H2 is not appropriately diluted or dispersed, it builds up, and the risk of fire and explosion increases. Mine Safety and Health Administration (MSHA) regulation (30 CFR Part 75.340) requires that battery charging stations should be housed in noncombustible structures or be equipped with a fire suppression system. When a fire suppression system is used, the battery charging stations must be ventilated with intake air that is directed into a return air course or ventilated with intake air that is monitored for CO or smoke using an AMS. The monitoring of intake air ventilating battery charging stations should be done with sensors that are not affected by H2."

Jan 1, 2018

By L. Yuan, J. H. Rowland, R. A. Thomas

Hydrogen (H2 ) gas released during battery charging can result in cross-interference for carbon monoxide (CO) sensors used for early fire detection and compromise the integrity of the mine atmospheric monitoring system. In this study, a series of laboratory-scale and full-scale experiments were conducted to evaluate the responses of different CO sensors to H2 gas. In the laboratory-scale experiments, H2 concentrations in the airflow are constant, while in the full-scale experiments, increasing H2 concentrations generated as a byproduct of charging the batteries at the battery charging station rise to the sensors under different ventilation scenarios. The H2 concentrations at the CO sensor location were measured using H2 sensors and were correlated with the CO sensor response. The effects of ventilation and sensor location on the CO sensors responses were also analyzed. The results of this study can help mining companies to select appropriate CO sensors and improve the deployment of these sensors to safeguard underground miners.

By Richard A. Thomas, Liming Yuan, Lihong Zhou, James H. Rowland

Hydrogen (H2) gas released during battery charging can result in cross-interference for carbon monoxide (CO) sensors used for early fire detection and compromise the integrity of the mine atmospheric monitoring system (AMS). In this study, a series of laboratory-scale and full-scale experiments were conducted to evaluate the responses of different CO sensors to H2 gas. In the laboratory-scale experiments, constant H2 concentrations in the airflow, from 100 to 500 ppm, pass through sensors. While in the full-scale experiments, increasing H2 concentrations generated as a byproduct from charging the batteries at the battery charging station rise to the sensors under different ventilation scenarios. The H2 concentrations at the CO sensor location were measured using H2 sensors and were correlated with the CO sensor response. The effects of ventilation and sensor location on the CO sensors responses were also analyzed. The results of this study can help mining companies to select appropriate CO sensors and improve the deployment of these sensors to ensure the safeguard of underground miners.

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this study is to assess the impact of different reagents, such as limestone, lime, magnesium oxide, and sodium hydroxide, in experiments carried out in the single purification step and in two consecutive purification steps by raising the pH of a rare earth sulfuric liquor with the aim to remove or reduce the impurity concentrations in the rare earth sulfuric liquor. The choice for the best purification condition was made based on the minimum loss of rare earth elements (REEs), reagent consumption, and residue generation. The exploratory experiments show that it takes place in the two consecutive purification steps, the first one consists in dosing the limestone pulp until it reaches a pH of 3.5 followed by an addition of a lime pulp reaching a pH of 5.0. Under this condition, the results were a total removal of Fe3+, PO4 3− , and Th4+ ions and a reduction of 99%, 87%, and 37% w/w in the Al3+, UO2 2+, and SO4 2− concentrations, respectively, in the purified rare earth liquor. Furthermore, the lowest REE losses (8.3% w/w) and reagent consumption (4.3 kg/m3 ) and also a low residue generation (7.5 kg/m3 ) were observed in this condition. Despite reaching similar results regarding impurity removal, the experiments done with the addition of limestone, lime, magnesium oxide pulps, and sodium hydroxide solution in the single purification step, where the pH was raised to 5.0, presented higher REE losses (64.9%, 42.5%, 44.8%, and 60.9% w/w, respectively) and a higher residue generation (43.2, 25.1, 11.1, and 13.6 kg/m3 , respectively). This occurred due to the co-precipitation of salts containing rare earth elements in their composition. The experiments conducted with limestone, lime, and MgO resulted in a higher consumption of reagents, while the same result was observed when NaOH was used (4.3 kg/m3 ). In the experiments carried out with the addition of magnesium oxide and sodium hydroxide, the respective purified rare earth liquors presented a high concentration of magnesium, sulfate, or sodium, which could impact the quality of the marketable rare earth salts, whereas the salts obtained under the best condition observed in this study seem to be amenable for use as raw material in an attempt to obtain rare earth products with an acceptable chemical quality.

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this study is to assess the impact of different reagents, such as limestone, lime, magnesium oxide, and sodium hydroxide, in experiments carried out in the single purification step and in two consecutive purification steps by raising the pH of a rare earth sulfuric liquor with the aim to remove or reduce the impurity concentrations in the rare earth sulfuric liquor. The choice for the best purification condition was made based on the minimum loss of rare earth elements (REEs), reagent consumption, and residue generation. The exploratory experiments show that it takes place in the two consecutive purification steps, the first one consists in dosing the limestone pulp until it reaches a pH of 3.5 followed by an addition of a lime pulp reaching a pH of 5.0. Under this condition, the results were a total removal of Fe3+, PO4 3− , and Th4+ ions and a reduction of 99%, 87%, and 37% w/w in the Al3+, UO2 2+, and SO4 2− concentrations, respectively, in the purified rare earth liquor. Furthermore, the lowest REE losses (8.3% w/w) and reagent consumption (4.3 kg/m3 ) and also a low residue generation (7.5 kg/m3 ) were observed in this condition. Despite reaching similar results regarding impurity removal, the experiments done with the addition of limestone, lime, magnesium oxide pulps, and sodium hydroxide solution in the single purification step, where the pH was raised to 5.0, presented higher REE losses (64.9%, 42.5%, 44.8%, and 60.9% w/w, respectively) and a higher residue generation (43.2, 25.1, 11.1, and 13.6 kg/m3 , respectively). This occurred due to the co-precipitation of salts containing rare earth elements in their composition. The experiments conducted with limestone, lime, and MgO resulted in a higher consumption of reagents, while the same result was observed when NaOH was used (4.3 kg/m3 ). In the experiments carried out with the addition of magnesium oxide and sodium hydroxide, the respective purified rare earth liquors presented a high concentration of magnesium, sulfate, or sodium, which could impact the quality of the marketable rare earth salts, whereas the salts obtained under the best condition observed in this study seem to be amenable for use as raw material in an attempt to obtain rare earth products with an acceptable chemical quality.

By S. R. LaBrooy, J. Avraamides

Thermal reactivation of eluted carbon is an essential part of most carbon-in-pulp gold recovery plants. The effectiveness of the reactivation procedure depends on the nature and level of contaminants adsorbed on the carbon, the efficiency of the elution and the temperature, residence time and atmosphere within the kiln. The most commonly used kilns are evaluated in terms of their operating parameters and performance. Data obtained both in the laboratory and in the field emphasize the importance of carbon feed moisture content, kiln atmosphere and carbon conditioning on the activity of the kiln product.

Jan 1, 1998

By J. Noll, C. DeGennaro, C. Zhou, J. Srednicki

"The personal dust monitor (PDM) (model PDM3700), as well as other electronic devices, can cause electromagnetic interference (EMI) which can disrupt the operation of some proximity detection systems (PDSs). A 15 cm (6 inch) minimum separation distance between the miner-wearable component (MWC) of the PDS and the electronic device usually avoids these disruptions, but due to the amount of equipment on a miner’s belt and the method of wearing the PDM in some situations, this distance can be difficult to always reliably maintain. Another method of reducing EMI effects is utilizing magnetic field shielding. The shielding capability of several different materials was investigated by surrounding the PDM with the material and quantifying the EMI. A copper mesh pouch reduced the EMI from a PDM3700, allowing a minimum separation distance of 10 cm (4 inches) instead of 15 cm (6 inches) as shown in a previous study for an unshielded PDM. A MU-metal box had a better shielding effectiveness, as it further reduced the minimum separation distance to less than 7 cm (2.8 inches). Shielding reduced the EMI of the PDM with MU-metal providing better results than the copper mesh. These materials may be beneficial for shielding individual components of the PDM or for constructing a shielded pouch. However, before the advantages of a shielded pouch can be determined, the effects of just the shielding material (metal) on the PDS needs to be quantified. INTRODUCTION According to statistics from the Mine Safety and Health Administration (MSHA), 43 miners have been fatally struck or pinned by a continuous mining machine (CMM) since 1984. In an effort to prevent future striking and pinning fatalities from occurring, proximity detection systems (PDSs) have been developed and are required on all operating CMMs in underground coal mines, with the exception of full-face CMMs, by 2018 (MSHA, 2015)."

Jan 1, 2018

By Robert A. Haney, David J. Atchison, Kenneth G. Fields

Mining systems with greater than a 20-foot face advance (deep cut) have become popular due to their increased productivity and safety. The face dust collection system used in many of the mines employing the deep cut systems, incorporates a machine mounted dust collector with either a blowing or exhausting line brattice and a remote control operated continuous miner. In order to characterize and quantify the parameters used to control dust with these systems, the Dust Division conducted studies on four mining sections using continuous miners with deep cut mining systems. On each section, the dust control system incorporated line brattice with a machine mounted dust collector. The remote control made it possible for the continuous mining machine to advance further while permitting the operator to remain under supported roof and away from dust generated during mining. The purpose of these studies was to evaluate the effectiveness of deep cut mining systems using dust collectors to control respirable dust exposure. This paper summarizes the results of the studies conducted. At each mine face workers were sampled to determine their full-shift dust exposure. Additionally, fixed point dust samples were collected at various locations to determine relative concentrations of dust generated from mining. Air quantities were measured at each working place to determine the amount of air delivered to the face area. Evaluations were made by comparing worker exposures to respirable dust samples taken at appropriate locations upstream and downstream of the coal faced being mined. An estimate of the amount of the respirable dust being generated at the face during mining and the amount of respirable dust being removed by the dust collectors was made by balancing the air quantities and the dust concentrations immediately upstream and downstream of the coal face. Results of the studies showed that the dust control systems, were effective for controlling workers exposure to respirable dust. Dust collector efficiencies were determined to be approximately 85 percent. While the dust collectors were effective in removing respirable dust, the success of the systems with line brattice greater than twenty feet from the face, was dependent on the use of the remote control which permitted the continuous miner operator to remain out of the high concentration dust cloud in the working face. Dilution from intake air, combined with the dust collector efficiency, maintained exposure of other section workers below applicable standards.

Jan 1, 1991

By T. W. Beck

Overexposure to respirable dust remains a widespread health hazard to roof bolter occupations in underground coal mines. Recently implemented mist drilling technology was evaluated for its effectiveness in controlling respirable dust exposures for roof bolting personnel. This work presents the findings from NIOSH field and laboratory studies comparing respirable dust levels on mist drilling roof bolter machines to dust levels measured on machines using a conventional vacuum drilling system. Gravimetric and instantaneous respirable dust samples were collected for multiple drilling cycles. These dust measurements were used to assess the potential dust control capabilities relative to conventional drilling. Controlled laboratory tests found 0.3 mg/m3 more respirable dust with mist drilling than with the conventional vacuum method. A separate field investigation of the two techniques observed higher dust levels around the mist bolting machine.

Jan 1, 2008

By Justin R. Patts, Andrew B. Cecala, A. KYLE LOUK, Emily J. Haas

The National Institute for Occupational Safety and Health (NIOSH) and the former U.S. Bureau ofMines (USBM) have given a significant effort over the past four decades in researching and developing engineering controls and interventions to reduce mine workers’ dust exposures during the bagging and palletizing of industrial minerals. Workers performing manual bagging and palletizing of 50- to 100-pound bags typically have some of the highest dust exposures of all workers at mining and mineral processing operations. This paper will provide an overview of available dust control technologies for bagging operations and present the findings of a recent case study that was conducted at four different industrial sand operations to identify the current types of bagging and palletizing technologies being used and to evaluate their effectiveness in reducing workers’ exposures to respirable crystalline silica dust. An evaluation will also be performed to determine if further reductions in respirable dust levels can be achieved by incorporating additional modifications or improvements into the existing technology.

Apr 3, 2020

By Justin R. Patts, Andrew B. Cecala, A. KYLE LOUK, Emily J. Haas

The U.S. National Institute for Occupational Safety and Health (NIOSH) and the former U.S. Bureau of Mines (USBM) have put significant effort over the past four decades into researching and developing engineering controls and interventions to reduce mine workers’ dust exposures during the bagging and palletizing of industrial minerals. Workers who perform the manual bagging and palletizing of 50- to 100-lb bags typically have some of the highest dust exposures of all workers at mining and mineral processing operations. This paper provides an overview of available dust control technologies for bagging operations and presents the findings of a recent case study conducted at four industrial sand operations to identify the current types of bagging and palletizing technologies being used and to evaluate their effectiveness in reducing workers’ exposures to respirable crystalline silica dust. An evaluation is also performed to determine if further reductions in respirable dust levels can be achieved by incorporating additional modifications or improvements into the existing technology.

By Dennis A. Beiter, Kenneth G. Fields, Richard T. Stoltz

Section 56.5001 Title 30, [Code of Federal Regulations1], establishes requirements for respirable dust exposure in Metal and Nonmetal Mines based on the Threshold Limit Values (TLV's) adopted by the American Conference of Governmental Industrial Hygienists. Respirable dust samples collected by Mine Safety and Health Administration (MSHA) inspectors at a sandstone quarry showed certain workers were exposed to excessive concentrations during development of a "coyote tunnel" that was ventilated with a blowing system. Because exhausting face ventilation systems are known to control dust more effectively than blowing face systems, a change was proposed to improve worker respirable dust exposures. This paper describes the evaluation of the proposed exhausting ventilation system in the quarry's "coyote tunnel" and compares the respirable dust exposures with those measured by the MSHA inspectors with the blowing system. Results showed the proposed exhausting ventilation system reduced respirable dust exposures to less than 20 percent of those measured by MSHA inspectors when the blowing system was used.

Jan 1, 1993

'IM existing predictive methods were chosen for evaluation; an influence function (Bals Theory) and a profile function (hyperbolic). These ere applied to several field measured subsidence profiles over United States coal mines. The effect of homogeneous versus non-homogeneous overburden on surface subsidence is demonstrated and the utilization of Bals Theory as a subsidence predictive method for both types of overburden is examined. The major factor affecting subsidence profile characteristics is the migration of the inflection point toward the centerline of the longwall panel. A computer program was written to aid in the analysis.

Jan 1, 1982

By Zhongxue Li, Baolu Zhou, Yiqing Zhao

"Rare earth elements (REEs) are a kind of new materials which have excellent optical, electrical and magnetic properties, and they play an important role in the development of high technology and green energy industries. With abundant reserves and a wide range of REE type, rare earth industry has a rapid development in China in recent years. However, environmental issues associated with REE exploitation have severely restricted the sustainable development of rare earth industry in China. At present, literatures on the externalities of REE exploitation are very limited, especially in China. This paper builds an evaluation model based on life cycle evaluation to estimate the external costs of REE exploitation at Bayan Obo. The results show that the external costs for producing one metric tonne of rare earth oxides (REO) in Bayan Obo was CNY 34739 in 2013, the external costs of waste gas, waste water, radioactive substance, REE resource depletion, and land occupation are CNY 14945, 12515, 1400, 3199, and 2680, respectively. Waste gas and water constitute about 79% of the total external costs. The internalization of the external costs would reduce the financial profit of Northern Rare Earth (Group) by 18%. This study has taken into account only those externalities whose market values can be estimated, and therefore the external costs of REE exploitation in Bayan Obo is likely to be underestimated. The results fill the gap in literature and provide further understanding on the external cost of REE exploitation.Introduction / Background Along with increasing concern about environmental pollution problems caused by the usage of fossil fuel and the shortage of fossil energy, a transition has occurred where development has moved toward green and renewable energy sources with less pollutant emissions (Stegen 2015). Rare earth elements (REE) are a group of important raw materials for these trends since they have unique magnetic, electronic and optical properties, and thus make them widely used in making high-performance magnets and energy saving lamps (U.S. DOE 2010). In addition, REE are crucial for manufacturing of widespread high-tech applications in medical, defense and electronic industries. Many countries have made medium-term and long-term plans for the development of their REE industries, and the annual growth rate of global REE demand is expected to increase by 6% by 2020, and reach about 170,000 metric tons of rare earth oxides (REO) by 2020 (Rollat et al 2016)."

Jan 1, 2017

By Kefton H. Teague

History of the feldspar industry in the United States has been summarized by DuBois (I)*. The earliest production of feldspar in the United States is reported to have been from Mitchell County, North Carolina, about 1744, with the product shipped to England, In about 1825 several pegmatites were worked to a limited extent in Connecticut, with the production shipped to England. The first feldspar grinding facility was constructed about 1850 in Connecticut, with chaser mills used. Feldspar has been produced continuously in the United States since about 1870. Feldspar is produced from the following states: North Carolina, California, Georgia, Connecticut, South Carolina, South Dakota, Kansas, Oklahoma, Virginia, Arizona, and Wyoming. Total United States production for 1969 will amount to approximately 900,000 tons. The most current published figures for world production is 1966, at which time 2,165,000 tons was produced. It is estimated that world production of feldspar for 1969 will amount to 2,410,000 tons. Historically, feldspar has been produced by hand sorting and hand cobbing of coarse block feldspar obtained from the intermediate and wall zones of zoned pegmatites. In the United States the reserve of known block feldspar, recoverable by hand sorting is nearing depletion. More emphasis is now placed on feldspar sources contained in finer grained rocks, especially coarse granites or fine-grained pegmatite and beach, dune, and river sands from which the feldspar is obtained by beneficiation.

Jan 1, 1970

By T. V. Vasudevan

Floc properties such as density, size, size distribution, porosity, and shear strength govern the effectiveness of flocculation as a process for solid-liquid separation. The floc characteristics desired for removal of suspended solids by sedimentation or filtration, for example, are known to he different. In this study, an attempt has been made to evaluate the effects of various physical and chemical factors on the density and shear strength of the flocs.

Jan 1, 1990

Floc properties such as density, size, size distribution, porosity and shear strength govern the effectiveness of flocculation as a process for solid-liquid separation. Floc characteristics desired for removal of suspended solids by sedimentation or filtration, for example, are known to be different. In this study, an attempt has been made to evaluate floc density using a simplified procedure and determine the effects of various physical and chemical factors on the density of floes obtained. A brief discussion of techniques employed to measure the shear strength of flocs and the effect of various parameters on the floc strength is also presented.

Jan 1, 1988

By W. N. McAnulty

Because so many interrelated technical, economic, legal and political factors are involved in evaluation of commercial mineral deposits, it is common practice today to assign such work to a team of specialists including geologists, mining engineers, metallurgists, lawyers, and economic evaluation experts. Each member of the team plays an important role; the role of the geologist is particularly important. The geologist involved with evaluation of fluorspar deposits needs all the geologic and economic training and experience required for evaluation of metallic mineral deposits. Few, if any, industrial or metallic minerals occur in so many geologic environments as fluorite. Fluorspar, and aggregate of rock and mineral matter containing enough fluorite to make a commercial deposit (ore), is somewhat more limited in its modes of occurrence than fluorite, but it too is found in a variety of environments.

Jan 1, 1970

By Joseph J. Garbarino

World demand for phosphate fertilizers has grown at an average annual rate of between 6 and 7 per cent over the past 10 years. In the next five years world demand is expected to at least continue to grow at that rate. Also, the continued need for improved fertilizer materials, coupled with improvements in fertilizer technology, have placed added importance on the use of phosphoric acid as a starting material for high analysis phosphate fertilizers. This demand for phosphates and phosphoric acid must be met by increased production. Increased phosphoric acid production also brings increased demand for chemical processing agents including foam control agents. We at Arizona Chemical Company have closely followed the phosphate fertilizer industries needs. Arizona Chemical Company has been an important supplier of flotation agents to the phosphate industry, primarily from its Panama City, Florida plant. We have also recognized the important role played by foam control agents in the wet-phosphoric acid manufacturing process. We feel it is the responsibility of the supplier of foam control agents to offer specifically designed products that are highly efficient and economically useful. The difficulties involved in evaluating foam control agents in the plant are recognized. Owing to the large number of variables present, and the difficulties in controlling these variables during the period of a plant trial, plant evaluation of a large number of foam control agents is impractical. We have attempted to develop a practical, reproducible, and yet rapid, laboratory evaluation test which correlates with plant performance.

Jan 1, 1966