Search Documents

"A fire design innovation of the concrete lining of the Ohio River Bridges East End Crossing Tunnel has been developed. As a result from a fire suppression and tunnel ventilation system, the project design Heat Release Rate (HRR) was able to be constrained from 300 MW to about 50 MW. With this reduced HRR, concrete lining without passive fire protection may be acceptable, if the tunnel concrete lining will not result in explosive spalling during the designed fire event. Concrete explosive spalling test was proposed to verify this assumption. Since no standard concrete fire explosive spalling testing procedure exists, a project specific testing procedure was developed and fire tests conducted. From fire test results, it is concluded that the proposed tunnel concrete lining, in conjunction with the proposed fire suppressing and ventilation system, will not experience explosive spalling and does not require a passive fire protection system. INTRODUCTION The Ohio River Bridge East End Crossing Tunnel is part of a Public Private Partnership project, which connects transportation network between Louisville, Kentucky and southern Indiana. Located in Louisville, Kentucky, the twin-tube highway tunnel provides northbound and southbound lanes of the Kentucky approach to a new bridge across the Ohio River. Tunnel lengths are approximately 1,675-ft and 1,685 for the northbound tube and the southbound tube, respectively. Connected by two cross-passages, both tubes have a roadway width of 40-ft, for 3-lane traffic, and a vertical clearance of 26.5-ft.The Tunnel was constructed by drill and blast method with shotcrete and rock dowels as initial ground supports. The final tunnel lining consists of 16 inches cast-in-place concrete lining and 20 inches invert slab, with a waterproofing system around the tunnel perimeter. Two (2) tunnel side drains and one (1) invert drain were provided for each tube. This paper describes the rational in assessing fire design requirements of the tunnel final concrete lining, to answer the question whether a passive fire protection system is needed or not."

Jan 1, 2016

By D. M. Walters, C. M. van der Vyver, L. J. deVulliers

The occurrence of underground fires in narrow tabular ore- bodies where high density timber support is used is a dangerous and disruptive occurrence. The containment and extinguishing of the fire remains a very important consideration in reducing not only the loss in production time but also in limiting the extent of the area damaged by the fire. Mindful of this, Gold Fields have adopted and developed the inert gas generator system from its origins in Poland for use in Group precious metal mines. The system generates an oxygen- deficient atmosphere which is introduced in the fire area after this has been sealed. A number of problems had to be overcome to operate this system successfully within the infrastructure of these mines. Of particular significance is the operation of a jet engine, the prime component of the system, at air pressures encountered below sea level. The modifications have been found to be satisfactory to the point where, since 1992, ten underground fires have been extinguished using this system. Invariably, the areas affected by these fires were extensive (over 1 000 000 m3) and required continuous operation of these units over extended periods of time (in some cases in excess of 400 hours).

Jan 1, 1997

By Albert E. Ketler

The techniques for fire monitoring of conveyor belts in underground coal mines have been revolutionized by the advent of sensitive carbon monoxide sensors and computer monitoring systems. These new systems are rapidly replacing the previous thermal (fixed-point temperature) sensors that have been shown to be considerably less sensitive for early fire warning. CO is generally an excellent indicator of spontaneous combustion. However, the most recent non-flammable conveyor belt materials have been shown to "burn" with dense smoke, but without sufficiently high temperatures to produce much carbon monoxide. To cover this fire detection void, a smoke detector was developed to augment CO sensing for these new conveyor materials. However, computer monitoring provides the flexibility for handling this and other additional instrumentation as fire monitoring techniques evolve. CO, smoke and temperature sensing may eventually be advocated for complete fire monitoring.

Jan 1, 1987

By L. D. Savage

Several experiments were conducted using a large crib fire adjacent to a Kennedy Metal Products steel stopping in a simulated cross cut to evaluate the proposed mechanisms by which a mine fire would breach the stopping. Temperatures in the convective air paths on both sides of the stopping, at the surface of the roof and 16mm within the roof were measured to evaluate the effects of heat transfer. The results indicate that roof failure is the prime method of breaching this design of stopping.

Jan 1, 1996

By T. Glenn Pobanz

For more than fifty years Walter Kidde & Company, Inc. has engaged in the development and manufacturing of both fire suppression and detection equipment. Our initial work for the mining industry centered around dry chemical extinguish-ing equipment for mine haulage cars. To fulfill this need, Kidde engineered and developed a manually activated dry chemical system to provide protection for the wheel wells, cable reels, and motor compartments on various pieces of underground mining equipment. The next phase of mining operation fire protection for Kidde was the area of detection and automatic fire suppression for conveyor belt heads. Early in 1970, a field evaluation program and belt head demonstration unit was taken to 10 areas throughout West Virginia, Kentucky, Pennsylvania, and Ohio. This extensive field program was a joint effort with National Mine Service Company of Pittsburgh, Pennsylvania. The objectives of this program were to study mine hazard problems and to determine further requirements of mine operators. The resulting belt head detection system centered around our Continuous Strip Thermistor Core heat detector in conjunction with a Kidde stored pressure dry chemical extinguishing system. Continuous Strip detection has been in use for a number of years in aerospace applications. It has proven flexible and reliable for the rapid detection of overheat conditions and fires in engines of over half the aircraft flying today. The use of Continuous Strip gave us flexibility to protect surface areas over and around the actual conveyor belt head equipment. The nature of Continuous Strip allows us to bend, wrap, and attach the 20 foot long thermistor element over the desired protected points of the belt head. An integral part of the conveyor belt head protection system is the control panel utilizing our comprehensive knowledge of fire alarm control logic. This panel contains supervision circuits which sound trouble signals upon detecting a break in the Continuous Strip; breaks in the wiring to the remote electrical extinguishing activators or to the alarm bell; or loss of primary power. A separate control module provides the adjustable alarm temperature setting of the

Jan 1, 1971

By J. Greg Sanchez

The New South Ferry Terminal in the New York City Transit system represents an important milestone for the city. This is the first station designed and built in the 21st century. The design of the fire safety system included relying on Computational Fluid Dynamics to analyze the dispersion of heat and smoke, and modelling of people egress to determine the egress requirements. The project also looked into how to protect the structure from the heat exposure in order to meet the fire rating requirements. This paper provides an overview of the fire safety design approach taken to design the new South Ferry Terminal station in lower Manhattan and looks into fire modelling, structural fire protection, and station evacuation.

Jan 1, 2008

By Brian Y. Lattimer, Kray D. Luxbacher, Jonathan L. Hodges, Manuel J. Barros-Daza

The abstract discusses the importance of predicting fire response time (the time before conditions become untenable for firefighters) in underground coal mines. It introduces a data-driven approach using artificial neural networks (ANNs) to predict response time and fire size based on measurable parameters like CO concentration, mine geometry, air velocity, and time since fire detection. The approach was tested using simulations from fire models (FDS and FSSIM), showing promising results for real-time predictions during mine fires.

Mar 6, 2022

By Everett M. (Original by) White

Numerous articles have been written about the coal mine ; he has been compared with brave men who have gone out to conquer some unknown hazard throughout the ages. Now, however, modern mining is no longer something to be avoided, but a vocation that anyone can be proud of, with remuneration equal to or above that of almost any industry. A concerted effort is being made each day by both the operators of most mines as well as the state and federal inspectors to see that coal mines are as safe or safer than work places in any other industry. How- ever, it is true that mine fires and explosions have occurred in the mining industry since its inception. One of the earliest accurate references to such an occurrence is found in the transactions of the Royal Society of London. In the Colliery Managers' Handbook, 1898, Caleb Pamely writes of an explosion that occurred at Fatfield, England in August 1708, resulting in the deaths of 69 persons. He states: "Three of them, viz, two men and a woman, were blown quite up from the bottom of the shaft, fifty-seven fathoms deep, into the air, to a considerable distance from the mouth of the pit." It is interesting to note that women were employed as miners in England during that period. In the United States, the first record of coal mined was in 1702 by the Jamestown colonists. In 1786, about 20 years after Pittsburgh, PA was first settled, a charter was granted by William Penn to mine coal on the banks of the Monongahela River. Then in 1803, the first important coal company, the Lehigh Coal Co., was established. From this beginning, the mining industry continued to grow in importance and the first state mining law was formulated in 1870. The Pennsylvania state mining law was followed in 1873 by Ohio's, and in 1876 by Maryland's. A mine explosion at Avondale, PA in 1869 stimulated state legislatures to formulate these early laws. In 1907 near the town of Fairmont, WV, there were, within three days, two explosions resulting in a total of 597 deaths. Because of this, the federal government took action and by 1910, the US Bureau of Mines had been established. This was perhaps the most significant change in health and safety for miners during the first half of the 20th century as the USBM concentrated its entire efforts in the study, research, and testing of methods totally directed towards improvement of the health and safety of the miner. After a mine disaster in Illinois, a federal law was passed in 1940 calling for federal coal mine inspectors. Then in 1969, Congress enacted the Federal Coal Mine Health and Safety Act following a mine explosion near Farmington, WV. In 1977, the law was revised and included noncoal mining operations.

Jan 1, 1981

By I. J. Duckworth

Due to improved, stringent safety regulations, many modern road tunnels are statistically safer, per kilometer, than above ground roadways. However, the public perception and reaction in the event of a serious tunnel fire is very different to that associated with a surface incident. Vehicle fires in road and rail tunnels are recognized to represent an immediate and extreme danger to the patrons of those systems. Unlike workers in the mining and civil construction industries, the general public are neither trained nor equipped to fight fires or evacuate under deteriorating smoke conditions. Accordingly, for the majority of modern transportation tunnels the ventilation infrastructure is sized on the requirement to control the combustion products from worst-case fire scenarios and to provide a tenable evacuation route for the tunnel users. It is common for these same emergency ventilation systems to be employed, often in a reduced capacity, for other operating modes such as the dilution of pollutants during congested traffic conditions. This is one of the fundamental differences to mine ventilation, where primary ventilation systems are not typically sized based on fire scenarios. This paper presents an overview of the subject of fires in vehicular tunnels. This includes a brief history of major transportation tunnel fires followed by a discussion on the resulting legislation and standards that govern the design and operation of tunnel emergency ventilation systems. A summary is provided on the common criteria, theory, and design techniques that are employed during tunnel emergency ventilation systems design. Information is provided on fire detection and suppression, with a discussion on the growing acceptance of wet suppression as a means to mitigate major fires in road tunnels worldwide.

Jan 1, 2009

By J. R. Knudson

A major contribution to the art of blasting was made at the Cleveland- Cliffs Iron Company?s Hawkins Mine in Cashwauk, Minnesota during April of 1956. It was here that the first experiments with fertilizer grade ammonium nitrate were conducted-experiments which led to the development of the ammonium nitrate and fuel oil method of blasting which has been eagerly adopted by open pit and quarry operators throughout the United States. While this new blasting agent was a more or less natural outgrowth of the Akremite Process devised by Maumee Colleries of Terre Haute, Indiana; no one, to our knowledge, had used this particular combination of ingredients prior to this time. Certainly this was a "break-through" as far as the Lake Superior District was concerned. Akremite consists of a mechanical mixture of grained ammonium nitrate and a solid carbonaceous material packed in a plastic bag. At the time of its introduction to the Mesaba Range, Akremite sold for 10.5 cents a pound as compared to the 18 cent powder previously used in both wet and dry large hole blasting. The discovery of this agent was indeed a remarkable achievement, one that afforded a substantial reduction in blasting costs. However, Akremite proved to be only an intermediate step in the evolution of our present low cost explosives. Cleveland-Cliffs utilized prilled ammonium nitrate and fuel oil and then eliminated the mixing and packaging plant entirely by combining the two raw materials in the field at the drill hole collar or in the hole itself. Thus we have approached the ultimate in simplicity, for the blaster and his helper now manufacture their own explosives not only as they are needed but where they are needed, and at a cost of under 4 cents a pound. This two-man crew may charge and explode as much as 8 tons of ammonium nitrate in an eight-hour shift and in so doing break some 65,000 tons of ore.

Jan 1, 1959

By Warnie Flint

According to statistics compiled by the National Safety Council, US Bureau of Mines, American Medical Association, and other agencies, accidental injuries cause more deaths than all the leading diseases. No one is immune to an accident. Probably the best way to describe an accident is to say that it is an unexpected happening. The automobile driver is not expecting a terrifying crash, the electrician does not expect to be electrocuted, nor is the coal miner expecting the roof to fall on him. All personal injuries will not result in death. There is a multitude of victims who are living proof of what accidents can mean to an individual-victims who are blind, paralytic, missing arms, legs, etc. In most instances the earning power of these individuals is gone, and they are utterly dependent upon family or welfare. For many years there seemed to be an attitude that prevailed in industrial America that accidents were inevitable, and that so many fatalities and injuries should be expected. This, of course, was utter nonsense. Since the birth of such organizations as The National Safety Council, American Society of Safety Engineers, and. the US Bureau of Mines, much progress has been made in reducing accidents. The enactment of compensation laws greatly contributed to the progress that has been made. Does this mean that all accidents can be prevented? Unfortunately, it does not. Human psychology indicates that men will work unsafely or perform unsafe acts for the following reasons : 1) Lack of knowledge or skill. 2) Conflicting motivations, such as: (a) to be more comfortable, (b) to save time or effort, (c) to be accepted by a group. 3) Physical or mental condition. Nearly everyone desires his own safety, but not all individuals are willing to do what they know to do to insure their own safety.

Jan 1, 1981

By C. D. Breeds, F. E. Valencia, J. H. Pye

The "FIRST AUTOMATIC SHOTCRETE TECHNIQUE" (F.A.S.T.) system, provides safe, efficient methods of remotely lining, shafts/raises. Two systems are available; one system will be used to shotcrete a 3.04m (10-ft.) diameter ventilation raise at a mine in Mexico; the other system incorporating remote control and sensing devices will to used to shotcrete ventilation raises from 2.75-4.9m (9-16 ft.) in diameter. This paper describes development of the system, from idea to field use.

Jan 1, 1981

By James F. Reynolds

Introduction There are 1.4 Gt (1.5 billion st) of recoverable coal under less than 914 m (3,000 ft) of cover in Colorado in pitching seams. Snowmass Coal Co., in cooperation with the US Department of Energy, introduced the longwall mining method in pitching seams to North America. This venture is a coal mining research program directed toward the profitable production of coal under difficult mining conditions as found in pitching seams of the western US. Snowmass Coal classifies pitching seams into the following categories for longwall on the strike in seams 3 m (10 ft) or less thick: • Flat = 0 to 10°: Normal continuous mines and shuttle cars work efficiently. • Slight = 10° to 22°: The maximum pitch that rubber tired equipment will function. • Moderate = 22° to 40°: The angle of repose of mined coal. • Steep = 40° to 60°: The limit of safe use of this roof support. • Vertical = over 60°. The longwall roof support covered here will work in all pitches except vertical. The shearer and conveyor will work in flat through moderate conditions. Longwalling across strike with this equipment in seam pitch over 60° could be accomplished with an inclined face. Development of the first longwall panel began in 1979 and was completed in 1981. The longwall equipment was installed and mining began on Aug. 11, 1981. Mine Planning and Development The original mine plan took advantage of old works abandoned in the 1960s. The gates were developed on a two-entry system with the entries rising 2° to the strike, allowing water to drain from the face. The mining method was by Alpine F6A road header continuous miners with bridge conveyor type coal transport into 5.4-t (6-st) bottom dump coal cars hauled on 1.1-m (42-in.) gauge track by 7.2-t (8-st) battery locomotives. The initial concept was to haul coal from the longwall by battery locomotive. Lack of discipline, however, was shown in the irregular direction of the gate entries, and local rolls in the coal seams severely limited the capacity of battery locomotives. Current mining law prohibits using an intake escapeway for belts or trolley locomotives. A two-entry system is the simplest method of panel development in a pitching seam. A continuous miner cannot be trammed from one entry to another because of steep "X" cuts. Thus, the development requires a continuous miner in each entry. The configuration of the old mine works resulted in a first panel longwall block of three 108 m x 1.6 km (355 ft x 5,400 ft). In panel development, the use of battery locomotives for coal hauling became evermore costly. When the panels were completed and the setup room finished, the lower gate entry was changed to a belt entry and battery locomotives were abandoned. A new slope was driven and the mine supply system was converted to rubber tire diesel supply. The latest generation of roadheader and standard high powered shuttle car-to-belt system is now used for development. Selection of Longwall Equipment Longwall mining across the strike on pitching seams is currently practiced in many nations. Equipment similar to that used by flat seam longwalls is available for pitching seam use in Great Britian and Germany. Face equipment includes a twin outboard armored face conveyor. It was selected to give maximum retention of coal on the conveyor due to flight rigidity and to prevent coal from sliding down the face and jamming the lower belt gate. Also selected was a 22-mm (0.9-in.) Dowty twin-outboard face conveyor for a 106-m (350-ft) face with a single 112-kw (150-hp) drive

Jan 12, 1983

By L. Mao

A first-order flotation rate equation was derived by incorporating both hydrodynamic and surface forces involved in bubble-particle interactions. The hydrodynamic forces were calculated using an appropriate stream function, while the surface forces calculated using the extended DL VO theory. The equation was used to predict flotation results as functions of several important parameters such as contact angle, Zeta potentials of air bubbles and particles, and bubble size. The predictions are consistent with experience, and can be explained in view of the various sub-processes considered in the model.

Jan 1, 1997

By P. Ulrich, V. Svalbonas

The early to mid 1980s was a period of mining consolidation, and many senior design engineers retired from the mill industry. Similar conditions have existed in the last few years. This creates a loss of a tremendous amount of experience. This paper is a look back by two senior mill designers who survived the dips in both time periods. From a continuous design practice of over 25 years, mill designs and fabrication practices are surveyed with a view of identifying what works, and is necessary, and what doesn’t, or is not necessary, in the creation of a safe, economic, long-lived grinding mill.

Jan 1, 2001

The National Mining Hall of Fame and Museum (NMHF&M) will induct the 2013 National Mining Hall of Fame class on Sept. 14, 2013. The ceremony will take place at the Brown Palace Hotel in Denver, CO. Representing the domestic and worldwide metal production, education, and health and safety sectors of the industry, this year?s five inductees cover a diverse cross-section of the mining industry. The inductees are: Charles F. Barber, Donald W. Gentry, Patrick H. O?Neill, Milton H. Ward and David A. Zegeer. They will join 218 other mining industry pioneers when they are formally inducted into the National Mining Hall of Fame at the 26th Annual Induction Banquet and Ceremony. They were selected for being visionaries, leaders and ambassadors, both within their own sectors and across the industry at large. Barber was a top executive at leading U.S. metals producer Asarco from 1956 to 1982. During his tenure, Asarco responded successfully to the demanding requirements of new environmental legislation in the United States and to changing concepts of foreign investment in mining, especially in Latin America. Gentry?s career took him from being a working mining engineer, to renowned mining educator, to president and chief executive officer of a mining company. As an educator, he had a positive impact upon hundreds, if not thousands, of new mining engineers and many others who took his short courses in mine economics. During his years in South America, O?Neill did everything from supervising operations of 15-bucket ladder gold dredges to becoming president of International Mining Corp. As an executive, he emphasized provision of education and training to local people working at mine sites for which he had responsibility. Ward?s experience covered the world and spectrum of metals, minerals and ores, ranging from A to Z (antimony to zinc and Australia to Zambia). He was president, chairman and chief executive officer of Cyprus Amax Minerals from 1992 to 1999, and he was president and chief operating officer of Freeport-McMoRan from 1983 to 1992, during which time he was instrumental in developing Freeport?s world-class Indonesian operations. Zegeer dedicated his mining career to protecting the health and safety of miners as a corporate executive, head of the U.S. Mine Safety and Health Administration (MSHA) and community leader. His tenure at MSHA coincided with a period of remarkable progress in U.S. mining safety .NMHF&M Board of Directors Chairman Paul C. Jones said: ?The five outstanding gentlemen being honored this year as inductees into the National Mining Hall of Fame are classic examples of the leadership and work ethic that has made America?s mining industry the world leader in technically sound, environmentally and socially correct, and economical mineral production that sets the standards for mining worldwide. We are very proud to add these five legendary gentlemen, who have demonstrated their sound technical and management skills to advance society on a worldwide basis, to our current list of 218 inductees being honored by the National Mining Hall of Fame.? 2013 Prazen Award winner ? The Nevada Mining Association is the recipient of the 2013 Prazen Living Legend of Mining Award

Aug 1, 2013

The National Mining Hall of Fame will induct five mining greats on Saturday, Sept. 17, 2005 at the Museum Convention Center in Leadville, CO. The 18thAnnual National Mining Museum and Hall of Fame Induction Banquet will begin with an open house and reception at 5:30 p.m., followed by the dinner and program at 7 p.m. The five inductees are Nathaniel Peter Hill, John Munro Longyear, John McDonald, Julius Eckhardt Raht and John Dennis Ryan. Nathaniel Peter Hill (1832-1900) built the first successful smelting operation in the Rocky Mountains in1867 at Black Hawk, CO. From 1879 to 1885, he was a U.S. senator. He also taught courses at the Colorado School of Mines.

Jan 1, 2005

By Robert A. Jankowski, Fred N. Kissell

Recent allegations about tampering of coal mine dust samples have led to suggestions that the coal industry needs a respirable dust compliance sampling method that is less subject to tampering. The sampler designs under consideration include fixed location monitors that could be mounted on a mining machine or located at a stationary location in the mine, and samplers that are worn, like the existing samplers. Fixed-point samplers have a design advantage, since samplers worn on the body will have size and weight limitations. On the other hand, in some cases there are respirable dust concentration gradients, which will dictate careful placement of a fixed-point sampler inlet to determine the exposure of workers. This study examined dust concentration-gradient data obtained by the Bureau of Mines and others over the last decade. As an example of spatial gradients at continuous miners, a fixed-point monitor located in front of the operators cab shows a higher dust concentration than a sampler located on the operator and reduced exposure when the sampling location is behind the operator cab. It may be necessary to use a sampling tube with a machine mounted monitor, to sample in the operators breathing zone in the cab to provide a more representative sample of the miners exposure. For face workers on longwalls or on continuous miner sections using remote control, the study shows significant dust level gradients and gradient variations between typical operator positions and mining machine locations. In addition, if fixed-point monitoring is used to monitor an area, vs the exposure of specific workers, dust control technologies currently employed to ensure reduced dust exposure such as the diversion of dust laden air away from the workers, or through the use of remote control of mining machinery may not indicate the same dust reduction obtained with current sampling techniques.

Jan 1, 1993

By L. J. Nicks

The current U.S. Bureau of Mines research program is addressing the recovery of flake graphite from kish, a steelmaking waste product, and the use of zeolites from abundant domestic natural deposits for efficiently cleaning up mining industry wastewater. The United States is almost totally dependent on imports for its graphite needs, but this may change depending upon the results from a pilot plant being constructed by industry using Bureau technology. Standard mineral processing techniques were applied by the Bureau to recover high-quality flake graphite from kish. It was considered innovative enough to receive an R&D 100 Award in 1992, and its commercialization has the potential to supply the total U.S. demands for graphite many times over. Zeolites have ion exchange properties similar to ion exchange resins, but are less expensive and available in large quantities. Samples of naturally occurring zeolites were tested for their efficiency in removing metal ions from synthetic and industrial waste solutions. The tests focused on defining their selecting, loading, eluting, and regenerating characteristics, and on developing a method for recovering the metal ions as added value products. The results showed that the removal of metal ions with zeolites from acid rock drainage (ARD) solutions is technically feasible and that this technique has the potential for being used in an integrated chemical treatment systems approach either as a primary or secondary cleaning step.

Jan 1, 1995

By Edwarde R. May

The Flambeau volcanogenic massive sulfide deposit located in northwestern Wisconsin occurs within the southern lobe of the Canadian Precambrian Shield. The steeply dipping tabular body occurs in a complex pile of cyclic schistose intermediate to felsic fragmental volcanics. No chloritic alteration pipe is recognized but adjacent rocks have undergone magnesia metasomatism and subsequently were metamorphosed to the upper greenschist and lower amphibolite facies. Although modest in size the deposit is of special interest in that it has an extensive and well preserved supergene enrichment blanket. Economic minerals found within a pyritized quartz-sericite schist are chalcocite and bornite overlying primary chalcopyrite.

Jan 1, 1976