Search Documents

By M. T. Ityokumbul

Flotation is a surfaced-based separation process that exploits the differences in the hydrophobicities of the components. In the present paper, a review of both established and emerging nonmineral applications of flotation (oil removal, paper de-inking and separation of plastics) is presented and discussed. For each application, the theory of the process is compared and contrasted with mineral flotation. It is shown that the mass-transfer approach to flotation offers a good starting point for the analysis of these separation processes.

Jan 1, 1999

By Abdelaziz Baçaoui, Imane Aarab, Mohammed Derqaoui, Abdelrani Yaacoubi, Khalid El Amari, Abdelmoughit Abidi, Abderahman Etahiri

Numerous researchers have addressed the complexity of the direct flotation separation of apatite from low-grade phosphate ore. The majority of these studies were limited to the micro-flotation scale. In fact, there is no warranty that a reagent scheme that showed a direct flotation of apatite at a micro-flotation scale on pure minerals would automatically replicate the same expected results on the natural ore in the mechanical flotation cell and so was the case for the phosphate ore studied. The overall trend was concentrating apatite in the non-float product. This study aspired to thoroughly assess the flotation performance of this never-exploited low-grade sedimentary phosphate using design of experiments (DOE). Unveiling new insights on such a strategy twist, various parameters and operating conditions, namely, desliming, type of collector and depressant, reagents dosages, conditioning times, flotation time, and pH, were addressed by multiple-factor screening using asymmetrical fractional factorial design followed by statistical interpretations. The collectors tested were the sodium oleate and a fatty acid mixture (FAM). The depressants tested were sodium alginate (NaAL), corn starch, carboxymethylcellulose (CMC), and sodium silicate. The results of the multivariable analysis revealed that desliming, pH, collector dosage, and flotation time significantly influenced the flotation process. Desliming was beneficial for the yield, P2O5 recovery, and SiO2 removal; however, there was still a compromise between grade and recovery. A strongly alkaline pH value of 12 stood out from the whole range. P2O5, CO2, and SiO2 grades of the products and flotation recoveries were improved, except for P2O5 recovery, which was negatively affected. A collector dosage between 2000 and 3000 g/t increased the P2O5 grade and reduced CO2 grade and recovery, enhancing the apatite/carbonates separation. A flotation time of 15 min was significant for P2O5 grade and CO2 recovery, nevertheless, at the expense of yield and P2O5 recovery. The products having initial concentrates of 28.08% P2O5 with a recovery of 88.96% and 29.41% P2O5 with a recovery of 62.71% were obtained using 25 g/t of NaAL and 2000 g/t of the collector FAM and sodium oleate, respectively, at pH 12.

Jun 5, 2022

By T. W. West

INTRODUCTION This paper presents an assessment of conventional flotation technology. In addition it presents some ideas which can be used to change the perception of what may be done with conventional flotation equipment to maximize its efficiency. Perspective of Conventional Flotation Technology 1. Flotation in many coal preparation plants is defined as something between a necessary evil and a non-viable concept because: -Too much art is required on a continuous basis to achieve uniformly acceptable results. -It is expensive, the capital cost in dollars per ton of circuit feed for flotation and dewatering is high. -It is a difficult process to use when SO2 reduction governs system design and equipment selection. -It creates a product (fine coal froth) that is difficult to dewater in the presence of BTU/lb as-received pressures. -It is a difficult process to control from a management standpoint, there are no dependable set points to rely on. 2. Many froth cell circuits are 0.5m x 0 (nominal 28 M x 0) feed which is sourced from screen/cyclone underflows. The original intent was to obtain maximum yield at acceptable product quality and moisture using disc filters. (See Figure #1) 3. An alternate to conventional flotation and its perceived to be limits of efficiency, capital costs, etc. is to move towards such developing flotation technologies as column flotation, reverse flotation, and microbubbles. A lot of work is being done to move these concepts thru pilot stages into full scale, commercial plant operation. The majority of the coal producers and coal preparation plant designers view these concepts as being in the development/pilot plant stages. OBJECTIVES Based on the preceeding comments of the perspectives of the coal producers and plant designers, the options are limited. They can make do with what they have available to them in the way of industry standard equipment and practices or they can move forward with developing technology. I feel there is a third option: what can we really do today with what is available to us, without reinventing the wheel? APPROACH 1. When processing coal against ash and SO2 restrictions, the fine clean coal stream can be the best stream on the clean coal conveyor due to the release by size and the ability to create a high BTU/low sulfur (dry basis) product. 2. Targets: -Consistent raw coal size consist in the plant feed . -Do not put pyrites in the froth cells. -Adjust criteria defining good flotation away from yield towards maximum BTU recovery at minimum ash. -Limit the froth cell feed size consist to 0.15 mm x 0 (nominal 100M x 0). -Establish and maintain a correct, consistent percent solids in the froth cell feed. -Select flotation reagents with care. -Introduce reagents in the proper sequence.

Jan 1, 1988

By Michael Drozd

Introduction Flotation is a recovery process that utilizes natural or chemically-introduced hydrophobicity of minerals to separate ore from gangue by attaching the ore particles to bubbles. Flotation has been known since 1906, when it was patented by E. L. Sulman, H. G. K. Pickard and John Ballot. Flotation's first documented plant use was in 1911, when it was used on gravity tailings from a zinc plant. Cyanide leaching was first patented in 1887. Most early precious metals flotation was linked to lead or copper concentrates. Most precious metal flotation is linked to sulfide recovery and utilizes such reagents as xanthates, dithiophosphates and thiocarbanilides. But the involvement of flotation in precious metals recovery does not have to be limited to active flotation of the gold and silver bearing minerals. Flotation can be used to remove interfering minerals, such as carbon, or cyanicides, such as copper, arsenic bearing minerals or other cyanide complexing minerals. Cyanide Leaching The use of cyanide to recover precious metals is the backbone of the industry. The various recovery processes that use cyanide are: 1. Leaching-Counter Current Decantation(CCD) Merrill-Crowe 2. Carbon-in-pulp (CIP) 3. Carbon-in-leach (CIL) 4. Vat leaching 5. Heap leaching These processes are selected depending on ore grade, ore leaching characteristics, reserve size and capital limitations. Ore grade is used as the first criteria to determine the type of cyanide plant required. However, the reserve size can determine whether a ground ore alternative is used. The ore leaching characteristics may indicate that the higher recovery, associated with a process that employs grinding, is the only economic recovery alternative. There are some extremely large leaching plants with grades that would be non-economic for some existing heap leach plants. Many factors, such as strip ratios, metal recovery and reserve size, determine what the ultimate plant design will be. The exact processing scheme that is used, is a multifaceted decision matrix, which gives the process metallurgist some job security. Precious Metal Recovery Using Flotation Flotation recovery can conceivably be used on any ore that has been ground. Many operations utilize gravity separation on the ore to remove native gold from the ore prior to sending it to cyanide leaching. On certain ores, where the gold is in visible nuggets or particles, this processing alternative is advantageous because the native gold cyanide recovery is

Jan 1, 1993

By Shi Wang, Hongbin Liu, Meiliang Wei, Wu Liu, Xiaojun Wang, Yuxian Ke, Xuepeng Song, Tiejun Tao

The study investigates the influence of water migration on the fluidity of fresh cemented paste backfill (CPB) with and without flocculant under variable shear rates. The research utilizes nuclear magnetic resonance (NMR), rheological tests, and scanning electron microscopy (SEM) to analyze water migration, rheological properties, and microstructure evolution. The findings reveal that water migrates to more stable states as shear rate increases, and the addition of flocculant enhances water migration and increases shear stress and apparent viscosity. The study establishes relationships between water content and rheological parameters, providing insights into the flow characteristics of fresh CPB for pipeline transportation.

May 4, 2022

By Darold Woodward, Stefan Haydn, Petr Pospisil

Most fatalities in tunnel fires are caused by the spread of toxic smoke. Controlling the spread of smoke is crucial to provide a survivable environment for emergency egress. A properly designed and tuned feedback control loop is required to achieve a target flow that is slow enough to allow pedestrians to escape under different boundary conditions. Feedback control loops are also helpful in optimizing energy consumption under moving traffic conditions. A reliable feedback flow control system requires sophisticated engineering knowhow and experience, careful selection of instruments and controlled variables, and thoughtful implementation from design through field testing and commissioning.

Dec 1, 2022

By Andrew W. Jenike

The first significant studies of problems related to the handling and storage of bulk solids were reported at the end of the nineteenth century. Early work originated from the necessity to store large quantities of grain and was concerned mainly with pressures affecting the structural design of silos and bins. The Janssen formula (about 1898) and the work of Ketchum [1] form the highlights of that period. In more recent years, progress in mechanization, increasing plant capacities, and rising costs of labor have focused the attention of engineers on the problem of gravity flow of bulk solids. A great deal of work has been done with models, and flow patterns obtained in small scale bins have been described in several publications, for example [2, 3]. An attempt to develop a theory of flow of bulk solids was reported in 1954 [4, 5, 61 and presented to the in a paper [7] in the same year. AIME recommended the continuation of this work and, as a result, Engineering Foundation granted a sum of money to set up a Bulk Solids Flow Laboratory. Two and a half years ago the project gained the support of the University of Utah and a laboratory was set up on the campus of the University. This project is now in progress, it has received the support of the American Iron and Steel Institute and of Kaiser Engineers, Division of Henry J. Kaiser Company. The results obtained to date are summarized in this report.

Jan 1, 1959

By J. D. Miller

Fluid flow phenomena and therefore the flotation efficiency of air-sparged hydrocyclone (ASH) flotation are strongly dependent on operating and design variables such as air and slurry flow rates, underflow and overflow opening areas, percent solids of the feed, reagent levels, particle size and ASH length. Time-averaged multiphase flow characteristics, as determined by X-ray CT (described in a previous publication), are used to understand and explain the steady-state ASH flotation of quartz. A detailed parametric study of quartz flotation by a nominal 2in. diam. air-sparged hydrocyclone (ASH-2C) revealed the influence of these variables on the flotation response, which is discussed in terms of the multiphase flow characteristics. Thus, a phenomenological description of quartz flotation has been established to assist in the further development and utilization of the ASH technology.

Jan 1, 1996

By J. D. Miller

Fluid flow phenomena and therefore the flotation efficiency of air-sparged hydrocyclone (ASH) flotation are strongly dependent on the operating and design variables such as air flow rate, slurry flow rate, underflow and overflow opening areas, percent solids in the feed, reagent levels, particle size, ASH length, etc. Time-averaged multiphase flow characteristics, as deter-mined by x-ray CT and described in a previous publication, are used to understand and explain the steady-state ASH flotation of quartz. A detailed parametric study of quartz flotation by a nominal 2-inch diameter air-sparged hydrocyclone (ASH-2C) revealed the influence of these variables on the flotation response which is discussed in terms of the multiphase flow characteristics. Thus, a phenomenological description of quartz flotation has been established to assist in the further development and utilization of the ASH technology.

Jan 1, 1995

By C. Dan Kealy

Recent antipollution legislation for the control of mine tailings and waste-water has required an increasing number of tailings ponds. Many of these new waste-retention ponds are being constructed in congested locations, or the older ponds have reached such a size that--if failure occurs--they pose a threat to human life and public property. Although the typical tailings-disposal embankment represents--to the casual-, observer or the economy-minded mine official--a rather ugly but benign and stable pile of waste, they are in fact an extremely sensitive structural mass, retained behind the frailest of dikes. Failure of the waste mass requires only a minor change in water retention or weather conditions, erosion or piping of the ground strata, shifts in load or slight earth tremors. When failures occur, the results can be disastrous. In the U.S., we have been fortunate that, so far, pond failures have not caused loss of life. Thus, failures in this country have attracted little public attention. Present tailings-pond construction methods used by the mining industry require the barest money investment, and little engineering effort. Unfortunately, this superficial approach may increase short-term profits, but the practice may be conducive to the construction of needlessly weak structures. In coming years many of these designs will probaly become corporate liabilities. A typical pond is portrayed in Figure IA. This particular pond in Arizona is 1 mile long and 3/4 mile wide. Illustrated in Figure lB is a representative pond in cross section. This paper in concerned with two basic features common to all tailings disposal: (1) location of the phreatic surface within a tailings-pond embankment because of its influence on embankment-slope stability, and (2) prediction of

Jan 1, 1971

By Roy J. Leonard

Two small diameter sewer tunnel projects being hand dug under major highways in the Greater Kansas City area encountered problems which were unforeseen from the geotechnical engineering information supplied with the contract documents. Both tunnels were being excavated by experienced crews using steel liner plates. One required the use of compressed air for completion, while the other required poling boards. Both contractors overran their budgets and filed changed condition claims, and this promoted further geotechnical engineering investigations. Fissured clays beneath a water table were encountered at both sites, but the character of these clays differed; however, both were inadequately described in the original geotechnical engineering reports.

Jan 1, 1987

By F. B. Micheli

Introduction and Historical Background Although both sluices and devices using a simple flowing film are among the oldest known methods of concentration, they are still extensively employed in a variety of situations where they are not only efficient but also have a low operating cost. More particularly, they are valuable for making a bulk concentrate of high specific gravity minerals from alluvials and beach sand and in upgrading low value ores. The antiquity of some of the basic concepts can be seen in the fact that they are found in Agricola's De Re Metallica which was published at Basic in 1546, while in 1602, Carew114 gave a fairly clear account of tin ore dressing in Cornwall in which grass turves were used to catch the cassiterite. This is perhaps one of the forerun¬ners of the blanket strake. The planilla of Mexico, the lanchute of Malaysia and the old Cornish box huddle are also descended from these early strakes. In fact, a sluice with holes in the bottom for concentrate discharge was shown by Agricola, not unlike the principle used in the plane table and the lamflo sluice. The convex huddle for the treatment of sandy material appeared about 1848 and the concave form eight to ten years later. For the treatment of "slime" sizes, wooden dead frames which were manually worked were used in Cornwall for many years but gave way to the automatic water-operated type in 1860, and even a mechanically tilted frame was described by Henderson115 in 1857. Theoretical Considerations The behavior of solid particles in suspension depends to a great extent upon the pulp density and the size of the suspended particles. In a fairly dilute suspension, such as that normally used when dealing with small particle sizes, the behavior of particles in a flowing film results from two effects. These are the lateral displacement, which is determined by the time taken for each particle to penetrate the flowing film and reach the solid surface, and the resistance offered by each particle to further displacement after it has reached this surface. The initial penetration through the flowing film depends on the size and specific gravity of the particle and the thickness and viscosity of the film. As a result the smaller particles will migrate further before their movement is retarded relative to larger particles of the same specific gravity. The behavior on reaching the solid surface de¬pends on whether there is a single particle layer or, as is more often the case, a multiple layer or thin bed of material which is sufficiently dilated, permits the penetration of higher specific gravity grains. Thrust of Flowing Films. When a thin film of liquid flows over a plane solid surface, the layer next to the surface remains at rest but the velocity of the film increases with the distance from the surface and becomes a maximum near, but not quite at, the free surface. Therefore, a particle in suspension in such a film is acted upon by a greater force near the upper part of the film than at the lower part, resulting in an overturning effect. After a particle reaches the separating surface or an accumulated densely packed bed of other particles, the liquid flow causes it to move downstream by rolling, sliding, or by a movement involving alternating suspension and deposi¬tion (saltation). In rolling and sliding, which are brought about by a substantially noneddying stream, the large submerged particles are acted upon to the greatest extent and they move more rapidly than smaller ones, notwithstanding their greater mass. When two particles of the same size but of different specific gravity are considered, the higher density one moves more slowly by reason of its greater mass. As a result the particles tend to become arranged in the manner shown in Fig. 29. If any particle is so large as to stand above the water surface, the transporting force on such a particle, although the maximum available, will have less effect than that on a submerged one. Such large grains are therefore carried a lesser distance. Fluid Velocity in a Flowing Film It can be shown that if y is the distance within the flowing film from the interface, the fluid velocity v' at this point is given by IIn this equation p' is the fluid density, g the acceleration due to gravity, a the viscosity, a the angle made by the film to the horizontal, and 0 the film thickness (in cgs units). Furthermore, the volume Q of fluid per unit time and unit width is related to the film thickness and can be calculated, since which upon integration gives Consideration of the velocity v' (Eq. l) and the terminal falling velocity µ derived from Stokes law enables the horizontal travel dz in time dt to be calculated as follows: Again integration and substitution of Eq. 3 gives In this equation, z is the distance travelled before a particle of density p at the top of the fluid film has settled on the concentrating surface. From these expressions it can be seen that the depth of the flowing film varies as the cube root of the volume of fluid and inversely as the cube root of the sine of the plane surface inclination. Similarly the distance a particle can travel before reaching the surface is directly related to the quantity of fluid and its viscosity. The viscosity of pulp is greatly increased by the presence of near colloidal particles and consequently the penetration of the somewhat larger grains through the flowing film is retarded, resulting in them being carried further across the concentrator deck. Obviously this effect can be reduced by prior removal of some or all of the ultra¬fine particles. The detrimental effect of kaolin on the separation of fine ferrosilicon from quartz has also been demonstrated by Johnston,116 the relationship between viscosity and efficiency of separation being shown in Fig. 30. The pH value also has a very marked influence on the viscosity and the use of acid mine water, for example, can increase viscosity materially and thereby result in lower efficiency. Dilation of Multi-Particle Systems Except during washing (when a single particle layer may exist) concentration usually takes place in a bed of particles which is partially dilated or stirred by eddy currents. The extreme case is seen in various forms of the sluice where the flow of water and the presence of riffles combine to create a fluid bed in which reverse classification takes

Jan 1, 1985

By James Wm. White

Calculation of consistent steady-state mass balances in operating metallurgical plants and pilot plants is of interest for many reasons. In general, enough data can - and should - be collected to overdefine the system, i.e., permit calculation of nonmeasured quantities via more than one path. In such cases, resulting steady-state metallurgical mass balances rarely close due to sampling, analysis and/ or instrument error. Indeed, determination of a valid calculational sequence for complicated process flowsheets with multiple recycle streams can prove quite difficult. Here we present and discuss a method that has proven useful in analysis of numerous grinding circuit flowsheets of varying-degrees of complexity our technique requires only a consistent process flowsheet with appropriate associated data and arbitrary numbering of streams and equipments. Process topology and user data are decoded to yield a set of "search" or base variables and a set of "calculated" variables in solids, water, particle size and splitter parameter space. This procedure greatly speeds subsequent actual mass balance adjustment calculations since perturing certain variables (e.g., a solids value) does not require recalculation of other variables (e.g., the water balance). Finally, internal search and calculated variables are back converted to User units and used in a Sum-of-Squares criterion. Global minimization of this performance functional then yields a consistent mass balance in a least, squares sense. Weighting factors of choice can be used. Examples illustrate application of these methods.

Jan 1, 1979

By D. Malhotra

This paper discusses the need for periodic auditing of mineral processing flowsheets and the potential benefits a company can gain from a study of this nature. A carefully designed flowsheet audit can have a significant impact on the metallurgical performance in the plant. Several case studies illustrating the potential benefits that can be attained from flowsheet auditing of mineral processing plants are discussed.

Jan 1, 1988

By Deepak Malhotra

This paper discusses the need for periodic auditing of mineral processing flowsheets and the potential benefits a company can gain from a study of this nature. A carefully designed flowsheet auditing can have a significant impact on the metallurgical performance in the plant. Several case studies illustrating the potential benefits that can be attained from flowsheet auditing of mineral processing plants are discussed.

Jan 1, 1986

By J. D. Allen

The Concord Mine Coal Preparation Plant of United States Steel Corporation, located near Bessemer, Alabama, began operations in June, 1950. The basic cleaning circuit consisted of a Chance Cone for cleaning the 2-inch x 3/8-inch fraction and concentrating tables for cleaning the minus 3/8-inch coal fraction. Dewatering of the final product was accomplished with 35-mesh vibrating screens. However, because Concord coal is very friable (Figure 1), 85 per cent passing three mesh and 25 per cent passing 28 mesh, there was a considerable amount of fines passing through the dewatering screens. To recover these fines, the dewatering screen effluent was sent to two 70-foot diameter hydro-separators with the underflow returning to the dewatering screens and the overflow going to a 175-foot diameter thickener for water clarification, (Figure 2). As might be expected, there was a considerable amount of recirculation of the minus 35-mesh coal in this system. This degraded the coal and led to higher moistures. It also resulted in a fines bleed-off of plant water and thickener underflow to a fine-coal settling pond. In 1961, vacuum filters were installed to supplement the screens and to recover the fine coal lost in the bleed-off. The above system resulted in a product moisture of about 20 per cent. Further reduction to approximately 11 per cent was accomplished by drainage from railroad cars during transit to the coke plant. Control of the moisture at unloading was poor because of variations in operating levels and railroad car availability, but since the Concord coal constituted a smaller percentage of the coal previously used at the coke plant, the high moisture and fluctuations did not seriously hamper coking operations.

Jan 1, 1966

By Benoit Gagnon

Mining of the Schefferville iron deposits began in 1954 on completion of the 574 km railway linking the mines and the St-Lawrence river port of Sept-Iles. Apart from crushing, no treatment of these ores was required before smelting. In the late 1950's, testwork began at Schefferville to develop a process for upgrading the extensive lower grade deposits containing 5l% iron with 15% silica (natural analysis). Engineering for 6.1 million tons per year Beneficiation Plant using cationic silica flotation and the A-C Grate kiln began in 1970 and the first pellets were produced in mid 1973. Production requirements and operating difficulties have restricted capacity to approximately 85% of design but ongoing improvements are being made continuously to attain design capacity.

Jan 1, 1980

By Nelson R. Shaffer

Implementation of the Clean Air Act Amendments of 1990 is negatively affecting production of coal used for generating electric power in Indiana and elsewhere in the Midwest. Required reduction of sulfur compounds from gas streams, or flue gas desulfurization (FGD), as mandated by these laws has encouraged installation of wet limestone scrubbers at many generating plants. Increasingly stringent requirements that will begin in 2000 are expected to necessitate even more extensive use of such scrubbers. Indiana has large deposits of limestone-the major consumable alkaline raw material for scrubbers-that can meet an expected demand of several million tons per year. Limestones are not, however, all the same. Different limestone units behave quite differently when used as scrubbing agents under differing conditions in actual practice. Decisions about FGD scrubber details would be more meaningful if made with thorough knowledge of which rock units contain the most efficient FGD limestones and which sites of suitable stone are located nearest to power plants. Even though abundant carbonate rocks occur in Indiana, their suitability in scrubbing systems has received little attention, and few attempts have been made to match details of stone resources to the needs of various utility scrubbing systems. Optimization of the fit between geologic characteristics of the existing limestones and prospective scrubber systems should allow for greatly improved planning and operation of FGD systems with attendant lower overall costs. Electric utilities have developed computer models to predict FGD system operations (i.e., the FGD-PRISM model of the Electric Power Research Institute). These models require geologic data such as reactivity that are commonly unavailable. We generated data needed for the model during a cooperative effort among the Indiana Department of Commerce, the Indiana Geological Survey (IGS), The Indianapolis Power & Light Company (IP&L), and the Indiana Mineral Aggregates Association. Our goal was to provide missing geologic details of Indiana scrubber-stone raw materials and apply them to the FGD-PRISM model to provide general guidance to determine which geologic units can provide stone for most efficient sulfur removal. Results of the model for selected limestones and parameters specific to one IP&L generating plant were calculated. Geologic data generated may be applied to other generating operations, and our examples should help other utilities optimize their FGD strategies. Several hundred samples from more than 30 active quarries were collected and their physical properties determined. Grindability values ranged from 7.2 to 21.7 for 50 selected samples. Acid-insoluble residues of less than 1% to 13% were found. Dissolution rates as an index of reactivity varied over two orders of magnitude for the selected set of samples. These data plus chemical analyses and Ca/Mg ratios were entered into a generic scrubber model to determine rates of stone use and scrubber efficiency for various stone. Removal of SO2 was projected by this model to range from 89% to 98% with stone utilization rates from 91% to 93%. Excellent scrubber stone sources were found in Mississippian rocks in central and southern Indiana. Rocks of the Ste. Genevieve and Salem Limestones were especially efficient. Even small amounts of dolomite, clay minerals, and quartz diminished a stone's usefulness for FGD scrubbing.

Jan 1, 1999

By John S. Lagarias

While systems to remove sulfur oxides from flue gases have been used at coal fired power plants since 1931, critical need for flue gas desulfurization has only occurred since the late 1960s following the passage of the Clean Air Act Amendments. Commercial and advanced flue gas desulfurization processes (FGD) are reviewed. Advantages and disadvantages of the processes are discussed. Regulatory requirements leading to the development of FGD systems are identified. The location and operation of coal fired plants may be determined more and more by the regulatory requirements for sludge disposal, waste, water discharge and air emissions.

Jan 1, 1978

By H. Yoon

Several processes involving injection of sorbent and humidification water downstream of the air preheater in a coal-fired boiler unit, are being developed as low capital cost retrofit S02 control options. Extensive laboratory work, pilot plant programs and larger scale programs have developed performance data and design information. Many of these programs were supported by the U. S. Department of Energy (DOE) as "proofs-of-concept" of three different processes proposed by Dravo, Bechtel and General Electric. Based on these project results, DOE formulated a comprehensive in-duct sorbent injection development program to fully commercialize the technology by 1992. Also, EPRI will conduct a 4 MWe pilot program to develop its HYPAS process. The Consol Coolside process is scheduled for utility demonstration in 1989 on a 104 MWe unit at the Ohio Edison Edgewater Station under partial sponsorship of the DOE Clean Coal Technology Program.

Jan 1, 1989