Search Documents

By S. Agarwal, S. Frimpong

The creation and maintenance of a healthy working environment in surface mining operations require sustained efforts in pursuing advanced research initiatives toward the development and deployment of powered haulage technologies. This paper contains progress summary on a frontier research in truck dynamic control, vision and collision avoidance. This research is required to provide solutions to challenging problems regarding operator visibility in truck haulage in a surface mining environment. The paper focuses on truck control kinematics and dynamics, truck-haul road interactions, intelligent truck sensing, intelligent truck collision avoidance system, integrated system for situational awareness, augmented visualization and operator interface, and field testing and error variance modeling of developed technologies. A sensor suite of four subsystems, including front-side stereo-camera, front-side Doppler radar, close range sonar proximity sensors, and rear-side camera system have been recommended for developing a 360° truck operator vision to allow safe operations. This research initiative is significant because it will provide a strong basis for developing technologies to improve truck haulage safety in surface mines and construction sites.

Jan 1, 2007

By Hans von Michaelis

It is difficult to fail if one has a great deposit, but 'great' ore deposits are few and far between. More often one hears that a mine has been 'made' rather than found. This is particularly true for industrial minerals and for gold and silver projects. Even the best ore deposit can often be improved through innovative technology, e.g. the Escondida copper mine in Chile, where a novel ammonia leaching process is yielding a fabulous DCFROI. Consider the case of a small high grade gold mine. Previous owners had found inadequate reserves to justify the capital cost of developing the mine and installing a mill. Lower grade resources had been ignored because the owners were looking only for grades that would be high enough to support a small underground mine and mill. Randol, assisted by Kappes Cassiday & Associates, determined that the ore was amenable for heap leaching. Secondly, existing drillhole data indicated a significant lower grade resource that appears to be accessible to open pit mining methods. In this case, the appropriate selection of off-the­shelf technologies has literally 'made' the mine. At the Randol at Vancouver '94 conference on Latin American Mining Opportunities, papers on innovative technolo­gies for exploration, mining, metallurgy and environmental management were presented in non-technical terms for managers and resource developers. It was surprising how few of the exploration- and finance-oriented delegates participated in these sessions. Numerous technologies were presented that could be added to one's arsenal of tricks to 'make' a mine, i.e. to convert resources into ore reserves through knowledge.

Jan 1, 1995

By Brian E. Davies, Bobby G. Wixson

INTRODUCTION The mining, extraction and refining of metals into useful materials is an honorable profession with an ancient and productive history. Civilizations have long depended upon metals for their implements, structures and machinery necessary for survival, growth, and development. Today, as in the future, metals and minerals are essential to the progress of mankind as we approach the 21st century with technologies and concepts that will require new concepts and production from the metal mining and processing industries. Today is the tomorrow we talked about yesterday and the implementation of new ideas is essential if we are to achieve "Frontier Technology in Mineral Processing". Unfortunately, the state-of-the-art mining, processing, smelting and refining methods historically employed were less than desirable environmentally, which has caused todays public to view the metal mining and processing industry with concern. Presently the ancient rock and chat tips connected with old Roman lead-zinc mines which were worked in Wales are causing stream contamination problems that must be corrected at considerable expense to the local governmental agencies (Firth, J.N.M., et al., 1981). However, improved progress has been made and the environmental control and clean-up procedures utilized by modern lead-zinc operations in the "Viburnum Trend" or "New Lead Belt" of South East Missouri may serve as a model to illustrate how alternative technologies, environmental concerns and cooperative efforts contribute to efficient mineral production within the confines of a U.S. National Forest region without significant environmental impacts. This area received international attention when it was opened within the boundaries of the Clark National Forest in the mid 1960's. By 1970 it ranked first in the world by producing 432,576 short tons of lead ore and has since continued in this position producing 451,153 short tons of lead ore in 1983 representing 91% of the total United States lead production (U.S. Bureau of idines, 1983). This production comes from a mining area approximately 40 miles long by 10 miles wide extending in a north-south direction. Geologically the lead is disseminated throughout the Cambrain age Bonneterre Formation, mostly a dolomite, at depths ranging from 700 to 1200 ft. (213.4 to 365.8 m). Galena (lead) is the principal ore mined with lesser quantities of sphalerite (zinc), chaleopyrite (copper) and silver being recovered as economic co-products. This new mining development in one of Missouri is most scenic areas could have led to a classic confrontation between industries and environmentalists. Instead, through the cooperation of industries, governmental agencies and university researchers, the Ozark environment has been protected, and may serve as a model for future coexistence of the mineral industry with the environment. Cooperative Program Development As early as 1965 five new mines and two lead smelters were being prepared for production and environmental concern was an essential part of that planning. All the mining companies became acquainted with representatives of the various federal and state agencies and scientists from the University of Missouri-Rolla (UMR). During the next six years, St. Joe Minerals Corporation, American Metal Climax, Inc., Cominco American Incorporated, Ozark Lead Company (Kennecott) and American Smelting and Refining Company participated in cooperative research efforts. The companies also participated in information exchange meetings, the development of improved analytical methods and the utilization of research findings in the modification or construction of pollution-abatement facilities. Early on research was carried out to determine background values and to establish natural baselines of trace metals in the surrounding environment. The unusual topography and drainage pattern of the mining area were helpful since it was possible to establish control sites and test sites below individual mine-mill operations to study waste-water effects on the receiving streams. The location of the ‘New Lead Belt', mines, mills,

Jan 1, 1985

By P. B. Queneau, J. E. Litz, T. P. McNulty

I. INTRODUCTION Modern hydrometallurgy has its roots in such notable successes as heap leaching for recovery of copper, cyanidation of gold ores, the Bayer process, the Oxland process for tungsten, electrorefining of copper, roast/ leach/electrowin process for zinc, and production of yellowcake from lowgrade uranium ores. Metallurgical testing techniques, sampling and analytical procedures, operating and maintenance practices, and improved methods and materials of construction which were pioneered in these processes have promoted the extension of hydrometallurgy into other applications. Periodically, new tools such as solvent extraction, resin ion exchange, and flocculants have opened new avenues to hydrometallurgists. Conversely, pursuit of more complex mineralization, the rising costs of energy and environmental quality preservation, and declining ore grades continue to create new challenges. For much of this century, it can be fairly said that practically any hydrometallurgical development moved the frontier of technology. The 1970's and 1980fs, however, have seen a significant maturing of hydrometallurgy's role in process metallurgy. Simplistically, this maturing seems to derive from a growing awareness of the strengths and weaknesses of hydrometallurgy and a determined effort to capitalize on the strengths. For example, many of us were among those revolutionaries of the 1960's and 1970's who taught that "chemical smelting" was the answer to the treatment of all sulfides. We now recognize, however, that only in very special cases can hydrometallurgy offer economic advantage over the generally less energy-intensive pyrometallurgical systems. The maturing of hydrometallurgy does not, however, signal stagnation. Important innovations are being studied and developed in most extractive areas, and a number are approaching or have achieved commercialization. From our company's perspective, that of an organization dealing with the development of the most economic solutions to metallurgical problems, innovation must be defined as the commercially successful reduction of an idea to practice. There appears to be no shortage of ideas, nor has there ever been a shortage. Many ideas now being implemented were conceived decades ago, but reduction to practice was foiled by the lack of such technology as responsive process control and economical materials of construction capable of withstanding highly corrosive or erosive environments. Commercialization of a new process is a particularly challenging undertaking. Even if technical risks are reduced to a minimum through careful and thoughtful process development, there are inevitable uncertainties in feed characteristics, variable costs, and product prices. Commercialization takes courage, both on the part of innovators who may be staking their careers or reputations and of investors who may face financial disaster in the event of project failure. This paper discusses innovative programs and recently commercialized processes which either have been discussed in the literature or disclosed to Hazen Research staff in private nonconfidential conversations with contacts in industry. Regarding this latter category of information, relative ease of communication has resulted in many of our observations being of North American origin.

Jan 1, 1985

By J de Cuyper, V. M. Lovell, W. Freyberger

The recovery of apatite from the phoscorite ores occurring in the Transvaal, Republic of South Africa, involves a flotation process that is particularly difficult to characterize from a fundamental point of view. However, the reagents used, (tall oil fatty acid, nonylphenyltetraglycol ether, sodium silicate, and sodium hydroxide) can successfully bring about a separation of apatite from dolomitic calcite, which is the most troublesome gangue component. Recently, it has been demonstrated with some flotation feeds that the addition of certain polysaccharides can improve the flotation significantly. It has been shown that the metallurgy obtained is closely linked to the nature of the froth, and this, in turn, is influenced, often dramatically, by the presence or absence of certain of the reagents. The character of the froth depends less on the inherent frothing ability of these reagents than on the presence or absence of fine mineral particles in the froth, and on their surface characteristics and state of aggregation. The polyglycol ether and the polysacchar- ides have been shown to affect these properties, and it is suggested that a major function of these reagents is to modulate the properties of the fine particles in the pulp, thereby changing the character of the froth and giving rise to improved results.

Jan 1, 1976

By B. J. Arnold, N. Terblanche

The features of the ‘Turbo’ froth flotation column will be discussed, including the double aeration system that improves flotation yield while not sacrificing grade, the internal launder system, and the unique feed/tailings sump that evens out flow to the flotation column preventing upset conditions. Results from various test programs and installations will be presented.

Jan 1, 2001

By Peter Amelunxen, Brandon Akerstrom

Since its introduction 40 years ago, the compartmental model of flotation has been used to predict the performance of mechanical flotation cells. However, it has found limited success for modeling dual-chamber machines and, as a result, engineers have adopted empirical correction factors usually derived from field audits of industrial cells to predict the performance of dual-chamber flotation cells. This paper introduces an extension of the compartmental model that applies to both single- and dual-chamber cells. The model is tested against pilot test work performed at Capstone’s Pinto Valley concentrator, and then used to evaluate the key operating and design parameters of dual chamber flotation cells. The results suggest that the design of the mixing chamber — for example, whether it is pneumatic or mechanically agitated — is not a significant contributor to overall machine performance. The work also suggests that the highest recoveries are achieved when the froth recovery is high, and longer separation chamber residence times and/or higher internal circulating loads are only beneficial when the froth recovery is low. Lastly, the results show that the single most important driver of the machine performance is the froth recovery of the separation chamber.

Mar 1, 2025

By M. Brändström, R. Dube, J. Moyo, T. Perkins, G. Bermudez, L. Bartsch, C. Smith, R. Sorensen

The Kennecott Copperton concentrator is currently the bottleneck for the Kennecott operation and several projects have been initiated to increase throughput. This increase in grinding circuit throughput has resulted in a coarser grind size which has impacted flotation circuit recovery. Metso Outotec 300m3 forced air tank flotation cells are currently utilized in the rougher flotation circuit at the Copperton concentrator. Higher overall recoveries have been observed on the newer Outotec tank cells compared to the original 85m3 self-aspirated flotation cells they replaced. However, coarse particle flotation response on these large, forced air cells did not show encouraging results when compared to smaller previously installed cells. This coarse recovery loss has been attributed to the longer froth transport duration and transport distance on large cells (100m3 and larger). Cell manufacturers addressed the risks of additional coarse particle losses in large cells by installing concentric circumferential launders and crowders (also called center launders). These are designed to reduce froth transport time and distance in the last cells in rougher stages where low residual floatable minerals causes a lack of froth mobility. The center launders also increase froth crowding, which also helps to increase froth transport velocity and increases copper and molybdenum recoveries. A trial set of the center launder retrofits were installed on the last three tank cells in one of the parallel rougher flotation rows at Copperton. The launder retrofits were installed at the end of October 2020 and monitored until March 2021. This six-month trial showed statistically significant improvements in copper and molybdenum flotation recoveries through the rougher circuit.

Mar 2, 2022

By M. Kaya

This paper presents an experimental method to determine the degree of gangue entrainment in mechanical flotation cells and proposes new and inexpensive methods to lessen it. The applicability of froth washing and vibration was studied in laboratory, pilot plant, and plant scales. The effect of wash water on metallurgical performance was tested with various streams from the Falconbridge Strathcona mill at laboratory, pilot, and plant scales, with the 2nd cleaner at the Eastmaque Kirkland Lake mill, and with the 2nd and 3rd zinc and 3rd and 4th copper cleaners at Les Mines Selbaie mill. It was found that gangue recovery was closely related to water recovery in all systems. Wash water at an optimum superficial rate from 0.03 to 0.07 cm/s reduced entrainment by anywhere from 30X to 70X. Wash water can be further assisted by mechanical and ultrasonic vibration of the froth. A further rejection of 10 to 20X becomes possible. As a result of this work, a number of plants in Canada and in the United States have evaluated and/or are now using froth washing.

Jan 1, 1990

By E. Manev

Thin aqueous equilibrium film studies and surface tension measurements on a mixed surfactant system consisting of polyethylene oxide (a model frother) and potassium ethyl xanthate (a model collector) enable the interaction between the two surfactants at the air/solution interface to be elucidated. For the film containing the non-ionic frother, the interface was charged and addition of low concentrations of xanthate acted as a common electrolyte and reduced the thickness of the film inducing rupture. However, at high xanthate collector concentrations, the negative charge xanthate was found to interact with the non-ionic and caused a build-up of negative charge at the air/solution. Higher frother concentrations were necessary to produce non-rupturing thin films upon increasing the xanthate concentration.

Jan 1, 1992

By William F. Riggs

The characteristics of frothers can often be determined by the proper selection of various chemical groups. There are three basic groups utilized in the application of frothers. These are alcohols, polyglycol ethers, and polyglycols. Some of the chemical groups are separated in subgroups. Each chemical group provides particular characteristics which affect load support, bubble diameter, water retention, air dispersion, and kinetics of froth formation. These chemical groups may be preblended in various percentages to optimize frother characteristics for a particular ore deposit.

Jan 1, 1986

By James A. Finch, Xiang Zhou, Yue Hua Tan

Widely used as collectors for nonsulfides, amines also show some frothing properties. Evaluating frother functions of amines and their combination with conventional frothers addresses whether one reagent delivering both collector and frother functions compromises the efficacy of either. From the findings, whether blending with frother confers any benefit requires knowledge of the residual amine concentration. If it is below about 10 ppm, blending eliminated coalescence, but there appears to be no benefit if the concentration is above 15 ppm.

By James A. Finch, Xiang Zhou, Yue Hua Tan

Methods to determine frother functions, control of bubble size and froth properties, are now widely used. Some collectors also exhibit frother functions which are less understood. Using a water-air system in a mini-mechanical flotation cell setup, this paper determines bubble size and water overflow rate for three amine collectors: one primary amine (dodecylamine, DDA) and two commercial ether amines (Flotigam® EDA and Flotigam® 2835-2L) and their combination with two common frothers, MIBC (methyl isobutyl carbinol) and PPG 425 (polypropylene glycol, molecule weight 425). Compared to the frothers, the amines were less effective in reducing bubble size, giving larger minimum size and the two commercial amines showed evidence of coalescence at low concentration. In blends, at fixed frother dosage, frother eliminated the coalescence but as amine concentration increased the amines dominated bubble size. Water overflow was a strong function of reagent type. For fixed 1-cm froth depth, PPG 425, Flotigam® 2835-2L and to a lesser extent DDA produced overflow while MIBC and Flotigam® EDA did not. In blends with frother overflow increased except with Flotigam® EDA. Mechanisms are briefly explored. The principal benefit of blending identified is the elimination of coalescence if residual concentration of the two commercial amines is below ca. 10 ppm.

By K. Rushdi, B. E. Abulnaga

The conventional Froude number is blind to the presence of solids, their density and their concentration in a stream of slurry mixture such as tailings flowing in an open channel. This often leads to rough approximations of subcritical, critical and supercritical regimes, based on one phase flow Froude number, limiting subcritical to a value smaller than 0.8 and supercritical to values above 1.4, as proposed in the past by Green, Abulnaga and other authors. While acceptable for small flows, such approximations can be uneconomical for the larger flows encountered in some modern plants that treat up to half a million t/day. A review of concepts of a densimetric Froude number sheds some light on the effect of solids on stratification prior and subsequent to a hydraulic jump. While the approach is heavily borrowed from modern sedimentology, it provides a useful tool to designers of large launders or open channel tailings systems. These concepts are reviewed with some practical examples.

Jan 1, 2013

By C. A. Young

Previous experimental results have shown that an increase in temperature and/or oxygen concentration leads to an increase in the hydrophobicity of fluorite (CaF2) with adsorbed oleate. Subsequently, ex-situ Fourier transform infrared (FT-IR) transmission studies suggested that this increase in hydrophobicity was the result of double-bond reactions between adjacent oleate species adsorbed at the fluorite surface. Now an in-situ FT-IR study on single crystals of fluorite has been used to monitor this phenomenon using internal reflection spectroscopy (IRS) with the crystals serving as reactive internal reflection elements. The double-bond reaction has been correlated with in-situ adsorption density measurements. These results demonstrate that only the first chemisorbed oleate layer undergoes the double-bond reaction at an appreciable rate. However, multilayers of precipitated calcium oleate in the case of fluorite appear to react minimally even for oxygen saturated solutions at elevated temperatures.

Jan 1, 1991

By O. Ozcan, J. D. Miller, Z. S. Nickolov

The production of soda ash from trona (sodium sesquicarbonate, Na2CO3•NaHCO3•2H2O) resources has completely displaced the production of synthetic soda ash in the USA. Further, the utilization of other trona resources is under consideration in China, Turkey, etc. Recent research has been concerned with the development of flotation technology for the trona industry. In this regard studies on the flotation behavior of sodium carbonate salts: trona, sodium carbonate monohydrate and decahydrate, as well as the flotation behavior of sodium bicarbonate, are reported for both cationic (dodecyl ammonium hydrochloride) and anionic (sodium dodecyl sulfate) collectors. It has been found that strong flotation of sodium bicarbonate (NaHCO3) can be achieved with 100% recovery, while the other sodium carbonate salts do not float well. These results have been explained by FTIR analysis of aqueous solutions of Na2CO3and NaHCO3in a range of concentrations from very dilute to saturated conditions. The changes in the shape of the O-H stretching band of water are correlated with the flotation behavior of Na2CO3salts and NaHCO3. In addition, the absorption band of the carbonate ion at ca. 1385 cm-1is used to monitor its interactions with water and/or other ions in solution. The infrared results demonstrate thatNa2CO3acts as a water structure maker, leading to an extensively hydrated surface that accounts for the poor flotation of most sodium carbonate salts. In contrast, NaHCO3does not have this characteristic and consequently complete flotation is possible with both cationic and anionic collectors. These results support the previous water structure analysis for soluble salt flotation of alkali halides and other oxyanion salts.

Jan 1, 2003

By E. Suoninen, K. Laajalehto, L. Kartio

Efficient separation of pyrite from other sulfides is of great importance for the metallurgical performance of flotation processes. In this work Fourier Transform Infrared Spectroscopy (FTIR) and X-ray Photoelectron Spectroscopy (XPS) were used to study the surface chemistry of pyrite in depression, activation and xanthate adsorption under conditions of controlled potential. Modifications of pyrite surfaces after treatment with depressants (lime, sulfur dioxide, sodium cyanide) and after activation with metal ions (Cu, Pb) were studied. The principal adsorption product identified on pyrite was dixanthogen whose formation started at about +0.15 V and +0.25 V (vs, SHE) in ethyl and amyl xanthate solutions, respectively. Copper xanthate was formed on copper(II) activated pyrite. Activation mechanism of pyrite by copper(II) salts is likely to be electrochemical where copper occurs as copper(I) on the surface of pyrite. Effective depression is achieved by sulfur dioxide and sodium cyanide. Depression at high pH is due to formation of iron(III) hydroxides. Calcium ions do not affect the electrochemistry but adsorb on pyrite and reduce the surface sites for dixanthogen adsorption.

Jan 1, 1995

By Gu Guohua, Hu Yuehua, Zhang Qin

The flotation behavior of pyrrhotite was investigated by using ethyl xanthate as a collector. Results showed that pyrrhotite had good floatability from pH 2 to pH 11, and poor floatability when pH was >12. The flotation of pyrrhotite was dependent on pulp potential on various pH values. The potential-pH range for pyrrhotite flotation was established. Cyclic voltammeny and FTIR spectroscopic analysis showed that the major adsorption product of ethyl xanthate on pyrrhotite was dixanthogen. The intensity of FTIR signals of dixanthogen adsorption on pyrrhotite and the anode current of a pyrrhotite electrode and flotation response of pyrrhotite are correlated with pulp potentials.

Jan 1, 2005

By S. Subramanian, K. A. Natarajan, D. N. Sathyanarayana

FTIR spectroscopy is used to study the ad¬sorption of an oxidized starch on hematite, corundum, and quart: substrates. The difference spectrum of the adsorbed starch on hematite indicates surface reactions involving -CH2OH and -COH groups and shows striking similarities with that of the ferric-starch system, suggesting chemical interaction between the iron of hematite and the starch adsorbate. The IR spectra of starch adsorbed on corundum and quart: show no evidence of chemical interaction, although hydrogen bonding is apparent. The extent of adsorption of starch on hematite. corundum, and quartz decreases along the series. The evidence for chemical interaction of starch with hematite is further obtained by the X-ray photoelectron spectra of starch adsorbed on hematite, showing noticeable decrease in peak positions of O(Is) and C(Is) of free starch. The Mössbauer spectrum of hematite with stanch adsorbed on it complements these findings.

Jan 1, 1990

By F. G. Hyde

Passage of the Public Utilities Regulatory Policy Act ("PURPA") in I 978 created an entirely new industry that is referred to today as the Independent Power Producers ("IPP"). Requirements of project owners, environmental compliance, project design, the financial community and most of all, the need to be a low-cost producer presented a unique situation for the sourcing and the utilization of fuels. Depending on the specific type of project being developed, (e.g. coal-fired, wood/biomass, natural gas, petroleum coke or a blend of several fuel types) and the type of boiler design, it is important to acquire fuels that will optimize both the project's operating efficiency and flexibility. This paper will focus on the acquisition of fuel for coal-fired projects, but will describe the necessary steps in the sourcing, contracting for, and the utilization of fuels and transportation resources in the IPP industry today.

Jan 1, 1996