Search Documents

By Mohammad R. Jafari

The Camp Dresser & McKee (CDM) has been retained by the Sacramento Regional County Sanitation District (SRCSD) to design the Mather Interceptor, a portion of the South Interceptor and Mather Interceptor program. The Mather Interceptor consists of 14,667 feet of 54 to 72 inch gravity interceptor. Approximately 90 percent of the alignment will be constructed via tunneling. Cobbles and boulders in a sand/gravel matrix dominate the ground conditions combined with seasonal perched groundwater table at some of the deeper reaches of the alignment, impacting design consideration. This paper will present the results of a comprehensive geotechnical investigation conducted for this project and in-depth technical evaluation of various trenchless techniques feasible for tunneling in the cobble and boulder laden formations of this project. This paper will also present the risks and issues of the design alternatives and selection criteria.

By Maurice A. Ponti

The D.C. Water and Sewer Authority is implementing the Anacostia River Projects component of its Long-Term CSO Control Plan, including 21 kilometers of 3.7- to 7-meter-diameter CSO near-surface diversion storage/conveyance structures and flood relief, pressurized-face, soft ground tunnels at a maximum depth of 65 meters. This paper describes a project-specific soil grouping system that is primarily based on soil characteristics for tunneling derived from tests including Atterberg limits, grain size, swelling, mineralogy, triaxial, pressure meter, and consolidation, which differentiates the project from past area tunnel projects using descriptive systems based primarily on area geology.

By H. Lawson

The Mine Safety and Health Administration (MSHA) issued Program Information Bulletin P09-03in April of 2008, providing formal guidance on using programs that model the redistribution of stress during underground mining of coal. A key part of this guidance is visual observation and mapping of ground conditions. If a correlation between ground conditions and model output can be established, the model is considered to be verified, and can be used to guide mine design in similar ground. A simple scale is recommended for ranking observed roof, rib, and floor conditions. This paper discusses optimization and implementation of a ground condition rating scheme in the gateroads of a deep underground longwall coal mine. Roughly 80% of each gateroad length deteriorated in a fairly uniform manner. However, this manner varied between gateroads, as did pillar size. The implementation of a ground condition mapping program, similar to that recommended in PIB 09-03, was successful in characterizing the ground response to mining in gateroads of a longwall coal mine.

Jan 1, 2012

By E. Zahl, J. Whyatt, H. Lawson

The U.S. Mine Safety and Health Administration (MSHA) issued Program Information Bulletin P09-03 in April 2008, providing formal guidance on using programs that model the redistribution of stress during underground mining of coal. A key part of this guidance is visual observation and mapping of ground conditions. If a correlation between ground conditions and model output can be established, the model is considered to be verified, and can be used to guide mine design in similar ground. A simple scale is recommended for ranking observed roof, rib and floor conditions. This paper discusses optimization and implementation of a ground condition rating scheme in the gateroads of a deep underground longwall coal mine. Roughly 80% of each gateroad length deteriorated in a fairly uniform manner. However, this manner varied between gateroads, as did pillar size. The implementation of a ground condition mapping program, similar to that recommended in PIB P09-03, was successful in characterizing the ground response to mining in gateroads of a longwall coal mine.

Jan 1, 2013

By T. Hackett

Western underground coal reserves are tremendous, but recovery in western seams can be poor because of mining problems caused by deep cover, geologic anomalies, and thick seams. For instance, many seams contain a rock parting too thick to be extracted economically with the coal. This forces the operator to mine the coal above or below the parting. Subsequently, the rock pressures induced by mining make the part left difficult or impossible to extract by standard mining methods. Because upper and lower parts of the seam are frequently of minable thickness, the presence of rock partings can result in a significant loss of coal. Given a longwall recovery of 60 pct and equal thickness for the two parts of the seam, overall recovery is reduced to less than 30 pct if one part only is mined. The coal left in place is unavailable to meet the nation's energy needs, or to produce revenues for coal companies or government. [ ] Multi-slice longwall mining has the potential to recover the portion of split seams that are now left in the mine. Using superimposed standard longwalls with chain pillars, overall recovery could be doubled, depending on panel and pillar widths. Using a combination of advancing and retreating longwalls in descending slices, overall recovery could be improved to more than 80 pct. Because of the potential for improved recovery, the Bureau of Mines is analyzing the ground control factors affecting multi-slice longwall under western mining conditions and is conducting field trials at a planned multi-slice operation.

Jan 1, 1987

By D. S. Choi, D. L. McCain

INTRODUCTION Coal is forecast to be an increasingly important and economical source of energy for the future as the supply of oil and gas declines relative to overall energy demand and perhaps in absolute quantities produced. With the decline in productivity, especially in underground mining, in the early seventies coinciding with the need to produce greater quantities of coal for market, a gradual change from room-and-pillar mining to longwall mining has been taking place in the United States. Consolidation Coal Company (Consul) produces about 50 million tons of coal per year with approximately 66% being from underground mines. Most of the mines are located in the Appalachian Region in the States of Pennsylvania, West Virginia and Virginia, and in Ohio and Illinois. Coal is produced by the room-and-pillar mining method with continuous mining machines in addition to an increasing number of longwall mining faces. Continuous mining machines will continue to be used for driving longwall development entries as well as in areas where partial extraction must be practiced in order to support the overburden rock because of surface structures or in areas that cannot be subsided, or where unfavorable geologic conditions limit the application of the longwall mining methods. ROOM-AND-PILLAR MINING METHOD Some background in the room-and-pillar mining method may be helpful to provide perspective. This method has been widely practiced since the beginning of coal mining in the region. It is a flexible system because it can provide either partial or nearly complete extraction, and coal pillars can be left where needed to support surface structures or oil or gas wells or because of unfavorable geologic conditions (Choi, Dahl and McCain, 1980).

Jan 1, 1983

By George R. Stephans

The Climax Mine is a panel caving mine which has had a long history of incidents of severe ground control problems. The nature of the ore deposit, which lends itself to the caving meth- of of production, a1 so makes the mine susceptible to large scale stress concentrations which are referred to as ?weight? problems. These problems have increased with increased production and also with expansion to deeper mine levels. During the past twenty years the mine has had to learn to cope with these problems in order to remain in operation. A number of practical guidelines and useful techniques have emerged from these efforts. The purpose of this paper is to share a few of these ideas. The Mine is located near Leadville, Colorado on the continental divide at an elevation of 3450 meters. The ore body is a large low grade deposit of disseminated molybdenum sulfide. It measures about 1200 to 1600 meters in diameter and it had an original depth of about 660 mters. The Mine has been in operation since 1918 and the massive nature of the ore body together with its blocky, highly fractured condition made it natural for the caving system to have been adopted for production at an early date. Open pit mining was started in 1973. The total plant has a capacity of more than 50 thousand tons per day, and more than 400 million tons of reserves at an average grade of 0.310 percent molybdenum disulfide remain to be produced.

Jan 1, 1982

By David Conover

The El Boleo Copper Project is currently in the final design stages for development of a 3-MM-tonne/yr underground copper mine located in Baja California, Mexico. The nearly horizontal mineralized zones are amenable to exploitation by conventional mechanized coal mining technology using continuous miners, shuttle cars, and belt haulage. The mine design resembles a typical full-extraction coal mining operation utilizing a sequence of mains, sub-mains and production panels. Due to numerous faults, mining will be conducted as several small adjacent mines accessed through adits from large arroyos cutting through the mine area. Up to four seams may be mined in some areas with a maximum overburden depth of about 250 m. The ore zone is relatively weak and plastic, subject to extensive creep over time. The mine workings will pass through areas of historical shortwall mining panels where the ground has flowed into old entries and gob areas, and then reconsolidated. A small test mine was developed to evaluate mechanical cutting performance, roof-bolt anchorage capacities, roof and pillar stability and caving behavior. In-mine measurements were combined with two- and three-dimensional FLAC models to evaluate alternative development and production pillar designs. The paper will discuss the various factors influencing ground stability at the El Boleo project and the strategies employed in developing a suitable ground control design.

Jan 1, 2009

By R. Karl Zipf

Highwall mining is an important surface coal mining method, and it may account for approximately 4% of total U.S. coal production. Highwall stability is the major ground control related safety concern. Ground control plans for highwall mining should specify hole width, web pillar width, barrier pillar width and number of holes between barriers. This paper offers simple design charts for these parameters aimed at providing “ball park” checks. Web pillars containing pre-existing auger holes are analyzed and a design chart for estimating their minimum width is also presented. Finally, close proximity multiple seam highwall mining, which may have caused several serious highwall failures, is analyzed. Web and barrier pillar recommendations for this special situation are presented.

Jan 1, 2005

By Frank E. Chase

Retreat mining is one of the most hazardous operations conducted underground. One of the keys to miner safety and an efficient recovery of the reserves is to design adequately sized production pillars to prevent pillar squeezes, excessive pillar spalling, severe floor heave, roof falls, and pillar bumps. Currently, few pillar design approaches are available which consider the abutment pressures generated by the gob. The Bureau of Mines is developing a method called Analysis of Retreat Mining Pillar Stability (ARMPS) to aid in the design of retreating sections. Back analysis of 42 case studies indicates that ARMPS can be helpful in predicting stability during retreat mining operations.

Jan 1, 1993

By F. Mensah-Dwumah, W. H. Baker, G. W. Clough

INTRODUCTION The practice of injecting chemical grouts into permeable soils in order to stabilize them for tunnel construction is a common procedure in Great Britain, Europe and Japan. In this technique, the grout penetrates the soil in a fluid condition, but hardens or "sets-up" in about one hour due to a chemical reaction. As a result, the soil, is strengthened and made less pervious, and this, in turn, reduces ground surface movements, limits ground water flow, and controls movements of the heading during tunnel construction. It is only within the last five years or so that this technology has been used in the United States. Most of the applications have been involved in the work for the Washington Metropolitan Area Transit Authority (WMATA) subway construction. The experience gained from this work is, in many instances, unique and should serve to guide use of the grouting technology in future projects. This paper documents five WMATA case histories; information is provided as to the soil conditions, method of treatment, reason for treatment, and tunnel performance. Locations of the five projects covered by this study are indicated in Figure 1. All are within the boundaries of the District of Columbia and involve soft ground tunnel construction. Basic information for the case histories is given in Table 1. Tunnel sizes and depths below the ground surface as well as general soil conditions are similar in all instances. The tunnels are about six meters in diameter and are located so that the crown is five to ten m below the ground surface. The soils typically consist of alternating sand, clay and silty sand strata. However, soil stratification details are

Jan 1, 1979

By Michael G. Nelson, Sekhar Bhattacharyya

Between 1974 and 1977, a detailed study of coal pillar strength was conducted by the University of Utah at the Beehive mine in southeastern Utah. This study was funded by the U.S. Bureau of Mines, and included laboratory testing of coal samples, extensive field instrumentation and measurements, and finite element analyses based on the laboratory results. Recently, a similar analysis of the laboratory results and mine design geometry was completed using the LAMODEL program developed by NIOSH. The results of this analysis were close to the data collected in the field. This study allows comparison with the earlier finite-element analysis, and illustrates the utility of the LAMODEL software suite.

Jan 1, 2005

In the last four years, 2007~2010, 9 out of 24 metal/nonmetal underground mine fatalities were caused by ground fall across United States of America (Mine Safety & Health Administration, MSHA). To reduce or eliminate incidents/accidents caused by ground fall, this paper clarified how to design and select ground support based on different ground conditions, how to use mine ground support standards, what geotechnical engineers and underground operators should do to keep mine production free of ground failures.

Jan 1, 2012

By N. M. Raju, S. K. Dutta, M. A. Khan, B. Singh

The paper seeks to present the application of ground control research at Mosaboni Copper Mines to increase the size of stoping areas. Room and Pillar stopes were experimented for increased production dispensing with the conventional breast stoping. The experimental stopes, with spans varying from 10 to 15 m, were extensively instrumented to study the behaviour of wall rocks (chlorite schist) and to determine the optimum span in the workings, dipping at 25° to 45° and 3 to 5 m in height. The observations confirmed that 15 m wide span could be safely worked with 3 m wide rib pillars at 600 to 800 m depth by using rock bolts. Ground conditions improved with the use of full-column cement grouted bolts dispensing with timber supports and the productivity was improved.

Jan 1, 1981

By Michael Murphy, Mark Van Dyke, VASU GANGRADE, Brent Slaker

Room-and-pillar mining in multi-level underground stone mines come with unique pillar stability issues. The pillar stability in these mines primarily depends on the thickness of interburden between mining levels and the staggering of pillars. NIOSH has previously established pillar design guidelines for shallow, flat-lying mines and single-level operations, but there is little guidance for ground control design in multiple-level stone mines. Therefore, to improve the overall understanding of ground control in these mines, a microseismic monitoring system has been installed at a multi-level underground stone mine in Tennessee with up to a 243-m overburden and a 7-m interburden thickness between levels. The microseismic system is comprised of nine uniaxial accelerometers and one triaxial accelerometer installed in the interburden. The seismic array is locally focused with all sensors installed within a 625 m2 area and is setup to monitor the seismicity around the formation of the pillar in the lower mining level. Data is collected over 11 months and comprises of over 1,000 high-confidence events that have been located in the study area comprised of post-blast activity. The event locations were identified using a 3D-velocity model, with an average 4-m location accuracy for this array calculated using the system data. Most observed seismicity was on the excavation boundary, both in the interburden and in the roof of the top level. At this stage of analysis, there are no significant rock failures with which to correlate seismicity, but event locations correlate well with presumed damage in the vicinity of blasts.

Apr 26, 2022

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 3,200 tons of ore per day with an average gold grade of 0.4 opt. The mine has a large horizontal extent of 2,500 feet by 500 feet and a vertical extent of 20 to 200 feet. High density of joints occurs within the host rock. Based on Rock Mass Rating and field observation, the Leeville ground conditions are characterized as poor to very poor. As such, heavy ground support is required for the mining operation in Leeville. Ore zones with a height in excess of 10 m (35 feet) are considered for longhole stoping. A typical stope measures 6.0 m (20 feet) wide, 30 to 55 m (100 to 180 feet, depending on the ground conditions) long and 10 to 30 m (35 to 100 feet, depending the thickness of ore body) high, yielding 10,000 to 20,000 tons when completed. Narrow ore zones, less than 10 m (35 feet), are mined using cut and fill. These drifts are 4.6 m (15 feet) wide by 4.6 m (15 feet) high. Based on the afore-mentioned poor ground condition, the establishment of a ground control monitoring system is key to operating both safely and successfully. The ground control monitoring system is composed of comprehensive instrument design and installation. Instruments include Multi-Point Borehole eXtensometers (MPBX) and Stretch Measurement to Assess Reinforcement Tension (SMART) cables. The monitoring system covers the mining zones and infrastructure openings. After about two year?s applications and measurements, useful data has been and continues to be collected to use in future stope and infrastructure structure design. The system provides the information making engineer and operation teams to do their job more confident and efficiency. Keywords: Ground control, Monitoring system, Long hole stope, Instrumentation.

Jan 1, 2009

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 2,903 t (3,200 st) of ore per day, with an average gold grade of 0.4 opt. The mine’s horizontal extent is large, 762 by 152 m (2,500 by 500 ft), while its vertical extent is 6 to 61 m (20 to 200 ft). A high density of joints occurs within the host rock. Based on rock mass rating and field observation, the ground conditions at Leeville can be characterized as poor to very poor. As such, heavy ground support is required for its mining operation. Ore zones with a height in excess of 10 m (35 ft) are considered for longhole stoping. A typical stope measures 6 m (20 ft) wide, 30 to 55 m (100 to 180 ft) long, depending on the ground conditions, and 10 to 30 m (35 to 100 ft) high, depending the thickness of the ore body, yielding 9,100 to 18,000 t (10,000 to 20,000 st) when completed. Narrow ore zones, less than 10 m (35 ft), are mined using cut and fill. Drifts at the Leeville Mine are 4.6 m (15 ft) wide by 4.6 m (15 ft) high. Because of poor ground conditions at this mine, the establishment of a ground control monitoring system is key to operating both safely and successfully. This monitoring system is composed of comprehensive instrument design and installation. Instruments include multi-point borehole extensometers (MPBX) and “stretch measurement to assess reinforcement tension” (SMART) cables. The monitoring system covers the mining zones and infrastructure openings. After about two years’ application and measurement, useful data has been collected and continues to be collected; this information will be used to design future stopes and infrastructure. The system makes engineering and operation teams able to do their job with more confidence and efficiency.

Jan 1, 2009

By Todd Minoski, Matthew McElhinney, Mark Mazzella, Morgan Sears, Craig Compton

The National Institute for Occupational Safety and Health (NIOSH) is staffed with Engineers, Geologists, and Field Technicians conducting a variety of ground control research. The mission of the ground control teams within the Mine Systems Safety Branch (MSSB) is to eliminate ground failures leading to mineworker injuries and fatalities. Advancing the science behind ground control relies heavily on conducting mutually beneficial research at participating mines which is detailed in specific references throughout the paper. The ground control teams have several types of field instruments at their disposal to measure the ground response in underground mines. These include borehole pressure cells (BPCs), vibrating wire stress meters (VWs), hollow inclusion cells (Hi-Cells), roof and rib extensometers, load cells, and convergence meters. These instruments are used to measure changes in pressure, strain, and displacement within the underground environment. Instrumentation data is collected automatically using intrinsically safe or MSHA permissible dataloggers if required. Information is transmitted to the dataloggers using approved cable to distances of 200–1,000 ft. depending on the type of datalogger being used. Once mining is completed, the dataloggers are retrieved and brought to the surface, providing in-mine data to mine management and engineers for the conditions currently being encountered in a particular mine. This data, in conjunction with geologic data and stress mapping, can be used to validate numerical models. The practical application of these models is extremely important for mine management and engineers, particularly when faced with more challenging mine environments. Insight gained from applying these models can be used to make better engineering-based judgments for areas that will be mined in the future. The impact of such applications can result in a reduction of ground-fall accidents and injuries as well as generally safer working conditions.

Feb 1, 2024

According to the classification of water conservation mining in shallow coal seams in China, when the ratio of the impermeable layer thickness to the mining height is less than 18, the mining belongs to the category of special water conservation, and the strip backfilling mining method is employed. This study is based on the geological conditions in northern Shaanxi. By analyzing the stability of the impermeable layer, the stability criterion of the impermeable layer was developed. The study also investigated the compositions and properties of the backfilling materials. The results show that reasonable subsidence of the impermeable layer is allowed during mining under the basic precondition (upward cracks and downward cracks are not connected).

Jan 7, 2020

By S. M. Hsiung

This paper presents the results of an extensive study concerning a series of roof falls in a room-and-pillar coal mine located in West Virginia. Three dimensional finite element modeling was employed to identify the possible causes for the roof falls. The effectiveness of possible roof control measures for alleviating or eliminating the adverse roof conditions is analyzed, discussed, and compared. The best mining alternatives are recommended. It has been found that large overburden depth and typical roof geology are the major reasons for the roof falls. Angle bolting may not solve the problem encountered in the mine studied. Changing the mine layout currently used in the mine appears to be the best alternative. The recommended pillar size and entry width which will eliminate the problem completely are 90 ft. x 90 ft. and 14 it., respectively.

Jan 1, 1985