Search Documents

Extending an organization?s knowledge base throughout the entire enterprise can improve operations. Until recently, though, field operations were often left out of the information loop, as extending high-bandwidth communications into harsh environments often proved impossible due to thermal extremes, physical hazards and caustic chemicals. However, advances in the design and manufacture of rugged fiberoptic cables have now enabled the successful installation of 10-gigabit transmission links to places such as mining operations. The experience of Consol Energy exemplifies how plant managers can successfully enlist ruggedized tight buffered cables to help carry the efficiency of ERP communications into even the most challenging work environments. ?As part of our ERP implementation, we extended our corporate network underground into our mines using fi beroptic cable,? said Tom Prokop, manager-site support for Consol Energy. ?We?ve actually had rooffalls bury the cable between rocks and still did not lose data communications. Our maintenance personnel are now able to access our ERP system while underground at locations that can be up to 32 km (20 miles) away from their desks or the warehouse. Access to the corporate network allows them to order parts, look at electronic schematics, access monitoring data, no matter where they are in the mine. With a few hundred workers below ground, this immediate access translates into a time-savings that adds up in a hurry.?

Jan 1, 2009

By Stig Eriksson

In Switzerland two major railway systems as shown below in Figure 1 has recently been completed or is under construction: ¦Lötschberg, south of Bern which was commissioned in 2007 ¦Gotthard, south of Zurich which is scheduled to be commissioned in 2016The aim is to increase the transport capacity of the railway system and to transfer more transport of goods to the railway by offering transport of trailers and lorries on the new railway systems. It will have a positive environmental impact but also improve the congested traffic situation of the highways in north-south directionThe Gotthard tunnel is totally 57 km (35 mile) long and the Lötschberg tunnel is 35 km (22 mile) long. Both tunnel systems consist of two parallel single track tunnels connected with cross tunnels at every 333 m (1 093 ft). Additionally there are cross-over tunnels and caverns for installations and operation. In the Lötschberg tunnel, the majority of the excavation has been by Drill & Blast and in Gotthard tunnel the major part is being excavated by TBM.

By Lee W. Abramson, James E. Crawley

Caltrans is studying alignments for a 160-kilometer-long high speed ground transportation system from Los Angeles to Bakersfield across the Tehachapi Mountains. This link is needed to connect southern California with San Francisco by a short passenger rail service. None presently exists. The system will require tunnels and viaducts along the route with sections crossing two major active fault zones. High speed ground transportation technologies are being evaluated for achieving rail speeds of between 200 and 480 kilometers per hour. This paper presents the technical requirements for tunnels along the alternative routes being considered for the project.

Jan 1, 1995

By T. Eggenberg

Mechanization and automation of logistic equipment has become one of the main key factors in raising productivity and competitiveness especially for complex and larger mining or tunneling projects. The Lake Mead Intake Tunnel #3 shaft mucking installation is a good example to demonstrate the potential that is found in an overall optimized logistic. It starts with the planning and results in using customized installations which fulfill the specifically defined requirements for the project. Rowa developed a solution and supplied a shaft mucking system using a discontinuous double drum hoisting concept with shaft buckets, loading, and unloading devices. With this fully automated system a continuous muck flow of 437t/h can be achieved.

Jan 1, 2010

By David M. MacGillivray

1. INTRODUCTION The economic importance of bringing a new mine to production in the shortest possible time, is well known. In recent years the rate of escalation of mining costs has accelerated more rapidly than at any time in the past. This fact has enhanced the need to reduce time schedules and made it an overriding and predominant objective when planning new shafts. The squeezed profit margins and widely fluctuating metal prices have also increased the emphasis being placed on this aspect. Moreover the increase in the present value of future profits due to the reduction in the time element, can be so substantial that expenditure on equipment and additional labour can be justified conditional on sufficient gain in shaft sinking speed being achieved. The emphasis on time saving becomes more abundantly clear when considering the very large increase in the capital required to bring a modern underground mine to production. As an example, the initial capital expenditure requirements for a large new gold mine in the Western Transvaal, which has commenced production recently, is estimated at R200M, and a major extension to another deep level mine in the same area is estimated at R300M. With the uncertainty of future metal prices and the recent trends in increasing inflation, it is becoming more difficult than ever to estimate the profitability of proposed mining projects and any cost saving due to more rapid sinking of shafts can only assist in this respect. Since the shaft systems are frequently the most expensive set of underground excavations and no other underground work can commence until they are completed, the speed of shaft sinking is subject to closer scrutiny than in the past. In the following sections of this paper the factors contributing to the high average advance rates achieved by South African shaft sinkers are discussed. It is difficult, if not impossible, to estimate the effect of any single factor, in isolation, on the overall sinking achievements. However, the cumulative effect of improvements made in the inter-related activities is, probably, the most important contributor. Although there has not been any single major technical change or innovation to shaft sinking practices in the last decade, the average sinking speeds have increased, due to improved application and technical improvements in established procedures. 2. GENERAL When discussing South African shaft sinking techniques and average sinking rates compared to those achieved in other parts of the world, it should be remembered that the size and depth of South African shafts are often considerably greater than in most other countries. Typical examples of shafts either in the course of sinking or recently completed are -

Jan 1, 1979

By Fred J. Fleischauer

Industry requires higher speed sheet stacking. High speed sheet stacking requires equipment and techniques to solve several inherent difficult problems, such as the tendency for sheets to sail, and the need for a means to absorb the kinetic energy of the sheet without damaging the sheet. Accurate alignment of the sheets on the stack is another problem difficult to solve. The paper first analyzes the process of sheet handling into its basic elemental steps. It then describes equipment and techniques presently used for moderate sheet handling speeds, with emphasis on how each step in the stacking process is accomplished by the present equipment. The limitations to speed-up of present equipment is discussed. New high speed equipment, either recently introduced to the market, or in the process of development, is described. Magnetic, air float and vacuum conveyor stackers are compared.

Jan 1, 1973

By Christian Neumann, Josef Arnold, Albin Reinhart

The Channel Tunnel Rail Link (CTRL) is the most significant railway infrastructure development project in the United Kingdom since the construction of the Channel Tunnel between France and England. The key element of this project is the 2-mile-long(3.2-km) North Downs Tunnel, which will be the largest and deepest twin-track railway tunnel ever constructed in the United Kingdom. This paper describes the contractual agreement, the design and construction (excavation and lining) of a twin-track rail tunnel with a 166-m 2 face excavated through chalk using the New Austrian Tunnelling Method (NATM). The importance of collaborating with a tunnel contractor/designer who not only is expert in the New Austrian Tunnelling Method, but who was also responsible for the design and installation of the primary lining, will be highlighted in this paper. This paper will also deal with the benefits of partnering in tunnel design and construction, as well as the resultant added values of mechanizing conventional tunnelling methods (Value Engineering).

Jan 1, 2001

By Edward S. Plotkin, Thames F. Peyton, Gary A. Almeraris

This paper describes high speed tunneling by drilling and blasting in a heavily populated urban area. The project consists primarily of mining 2500 m (8237 ft.) of tunnel through mica schist, excavating three shafts approximately 200 m (650 ft.) each and concreting lining 5300 m (17,400 ft.) of 7.34 m (24 ft.) inside diameter tunnel. The techniques developed and equipment utilized to ensure a high rate of tunneling advance are described. Extensive planning and good communications were especially essential in maintaining production on this project since tunnel mining, tunnel concreting, and shaft excavation all proceeded simultaneously from one common work shaft and a single heading.

Jan 1, 1985

By Kevin Stuffle, James E. Sharp, Sean Premeau

Two process enhancements for the biological oxidative pretreatment of sulfidic gold ore for subsequent treatment with cyanide are discussed. These are the use of a high areal density ring and pin packing (BioBalls™) as substrate, and the use of a novel biological ferric generator. The BioBall™ packing when coated with concentrates for heap leach processing offers higher areal densities, while leaving more open volume for fluid flow than more commonly used substrates such as aggregate. An oxidation rate study was performed on crushed auriferous arsenopyrite whole ore to demonstrate the benefits of using the packing. The auriferous arsenopyrite grading 2.9% Fe and .212 OPT gold was 50 percent oxidized in 24 days. The biological ferric generator is a passive air-side trickle bed reactor that efficiently converts ferrous to ferric in a process stream. Conversion rates of .8g/L h ferrous to ferric are routinely obtained. Although the biologically generated ferric solutions have not yet been tested on gold ores or concentrates, prior work has demonstrated that the high ferric solutions which will result in rapid oxidation of sulfidic gold ores or concentrates.

Jan 1, 1997

By R. Wild

[When a blast furnace has a certain defined burden and is operated under fixed conditions of blast temperature, etc., the fuel efficiency is determined by the extent to which the reducing gases can remove oxygen from the burden in the furnace stack. This is determined by two distinct factors: 1) The uniformity of gas-solid contact, and 2) The ease with which oxygen can be removed from individual pieces of burden. This latter is often called burden reducibility. When burdens were poorly prepared the first factor was by far the most important and a study of the reducibility of individual lumps was of rather academic interest recent years good burden preparation with emphasis on sized material has led to greatly improved gas distribution in the stack, and thus the second factor has become much more important and there has been a marked increase in interest in methods of measuring reducibility.]

Jan 1, 1964

By S. A. Pirzada

A thermal plasma assisted laminar flow reactor has been used to evaluate the kinetics of converting alumina to sodium aluminate in flight. Free energy minimization calculations were used to determine experimental conditions. The experimental variables include: alumina particle size, alumina/sodium nitrate molar ratio, temperature and residence time. A mathematical model for the conversion was developed and validated. Experimental and mathematical results are presented.

Jan 1, 1996

By Louis M. Schlesinger, Michael J. Garska, Joel F. Hutwelker, James T. Jr. Tanner

A pilot plant was constructed and operated to investigate the column flotation of 20 x 200 mesh North Carolina phosphate ore, using high throughput, high solids operating conditions developed at the NCSU Minerals Research Laboratory. Flotation was performed at 45% solids in a 9.5 cm (3.75 in.) diameter by 2.26 m (7.4 ft.) tall column at throughputs of 19.1 t/hr/m2 (2.0 stph/ft2) and 31.7 t/hr/m2 (3.3 stph/ft2). Recoveries in excess of 98% of the phosphate value were obtained at the lower throughput -- while obtaining concentrate grades containing over 28% P205 (61.2% BPL) at that recovery. Recoveries of about 95% of the phosphate value were obtained at the higher throughput, while making a concentrate averaging 27.6% P205 (60.3% BPL). In addition, a better understanding of the variables governing the column flotation of coarse nonmetallic minerals was gained. Variables examined included superficial air velocity, throughput (superficial feed velocity), frother type, frother dosage, and bias rate.

Jan 1, 1993

By J. F. Hutwelker

A pilot plant was constructed and operated to investigate the column flotation of 20 x 200 mesh North Carolina phosphate ore, using high throughput, high solids operating conditions developed at the NCSU Minerals Research Laboratory. Flotation was performed at 45% solids in a 9.5 cm (3.75 in.) diameter by 2.26 m (7.4 ft.) tall column at throughputs of 19.1 t/hr/m2 (2.0 stph/ft2) and 31.7 t/hr/m2 (3.3 stph/ft2). Recoveries in excess of 98% of the phosphate value were obtained at the lower throughput -- while obtaining concentrate grades containing over 28% P205 (61.2% BPL) at that recovery. Recoveries of about 95% of the phosphate value were obtained at the higher throughput, while making a concentrate averaging 27.6% P209 (60.3% BPL). In addition, a better understanding of the variables governing the column flotation of coarse nonmetallic minerals was gained. Low air flow rates adversely affected concentrate grade at the lower throughput. At the higher throughput, phosphate recovery decreased at an elevated air flow rate. An unexpected result of the study was the effect that frother type had upon phosphate metallurgy. Use of Nottingham Econofroth 925 provided better flotation selectivity than American Cyanamid F-65 at the low throughput. This is significant since the high' throughput tests were conducted with F-65 exclusively. It is reasonable to expect further improvement in high throughput performance when the optimal frother type and dosage are determined.

Jan 1, 1993

By J. Willison

Over the past decade, the coal mining industry has faced the difficult task of remaining profitable in the midst of declining market prices. Historically, the industry has been quite capable of meeting this challenge by various means. As total costs to mine and market coal continue to increase, new methods of tackling the problem must be implemented. Studies have shown that although many options exist to influence both inby and outby costs, the greatest potential remains in addressing costs at the coal face. Mining operations can positively effect a change in their profitability by either reducing costs, or by increasing production to in turn lower their net cost per man-hour. Original equipment manufacturers can play a key role in both options through the introduction of new technology that permits higher extraction rates, as well as other advantages leading to lower cost coal. A leading advancement over the past 30 – 40 year period has been the advent of progressively higher voltages to operate the mining equipment. This advance enables higher power transmission for a given cable size, operation at lower amperages resulting in less voltage fluctuation, and reduced heat on the cable and electrical components.

Jan 1, 2003

By F. M. Swain

High-calcium limestones occur in the upper part of the New Market Formation, of Lower Middle Ordovician age, in Franklin and Cumberland Counties, Pennsylvania. The high-calcium facies of the New Market Formation is represented by sublithographic limestone or vaughanite, which probably formed in quiet water; low-energy environments such as intershoal lagoons, or in protected bays similar to the present-day Florida Bay environment. Rapid facies changes are characteristic of the strata. The better grade of stone lies in the upper 100 to 125 feet of the New Market Formation and averages 95-97% calcium carbonate. Silica and magnesia are about equal in amount as impurities. One high-calcium belt extends from the Maryland state line through Chambersburg and Newville to beyond Carlisle. The strata in this belt are structurally complex, which requires careful field study' and core-drilling prior to exploitation. Stone suitable for blast-furnace flux is present in relatively large amounts, but stone for open-hearth use or portland cement requires more selective quarrying.

Jan 1, 1966

By Derek Brennan, Donald Brennan

"The existing Rondout West Branch Tunnel (RWBT) is part of the Delaware Aqueduct which has been in service since 1944 and accounts for more than 50 percent of New York City’s water supply. In early 2015, the New York City Department of Environmental Protection contracted Kiewit-Shea Constructors, AJV (KSC) to construct the Rondout West Branch Bypass Tunnel project (Rondout) in order to mitigate the leakage of 132 million L/ day (35 million gpd) of water from two areas of the existing tunnel; the Roseton and Wawarsing areas.The scope of the Bypass Tunnel 2 project is separated into two distinct phases. Phase 1 consists of completing the shaft sinking to a depth of approximately 274 m (900 ft) at shaft 5B, 213 m (700 ft) at shaft 6B and the excavation of approximately 3,850 m (12,500 linear ft) of tunnel at a diameter of 6.6 m (21 ft 7 in). This phase also includes the installation of 2,804 m (9,200 linear ft) of 4.8 m (16 ft) diameter steel interliner pipe through the new bypass tunnel with cast-in–place concrete liner for a finished diameter of 4.2 m (14 ft). Access chambers at the top of shafts 5B and 6B will be constructed for access and housing of the mechanical and electrical equipment for supporting pumps and valves.Included in phase 2 is the additional excavation from shafts 5B and 6B to the RWBT, and the drainage tunnel to remove ground water infiltration from RWBT. This work will be completed during a scheduled shutdown of the RWBT and will include approximately 31 m (100 ft) of excavation of the two connection tunnels. Additionally, construction of the permanent plugs within the RWBT will be undertaken. Figure 2 shows the layout of the work.Access to the work through the deep shaft at site 5B was critical to the success of the project. The hoisting system needed to be multi-functional to handle the different types of construction from drill and shoot of the shaft, starter and tail tunnel, the assembly of the tunnel boring machine (TBM), the excavation of the TBM tunnel including the supply of the precast segmental liner, the grouting operations, the installation of the steel interliner pipe and the cast-in-place concrete as well as ingress and egress of personnel. The production of the TBM operations was critical to the schedule of the project. This required a quick cycle for muck haulage and supply of the precast segmental liner in order to keep pace with the excavation time of the TBM. For TBM assembly, components were limited to a maximum weight of 104 t (115 st) for a single lift. Various cranes were analyzed for hoisting, however, none would meet all of the citeria. Therefore, the project team selected a specialized hoisting system designed in house in conjunction with Timberland Equipment Ltd. that consisted of a total of 14 separate hoists and winches with a total of more than 2,833 kW (3,800 hp)."

Mar 1, 2019

By N. O. Lotter

The reliability of a set of flotation results is key to minimizing project risk, either at the commissioning of a concentrator or at the point of implementing an improvement to an existing concentrator operation. High-confidence flotation testing (HCFT) was developed for this purpose and is part of the list of technologies at various scales used by Xstrata Process Support (XPS) in addressing these projects. The methodology is based on two principles: one, to ensure that the ore sample is representative and has been well-blended and subsampled; two, to perform the flotation tests in sufficient numbers of replicates with appropriate quality controls, so as to improve the reproducibility of the test data. Across ten years of research on this methodology at Xstrata Process Support, Sudbury, several improvements to the HCFT method and complementary connections between sampling and quantitative mineralogy have been developed. Two case studies are reviewed. These show the capability of this system in both optimizing an existing concentrator operation and in serving a new mine scenario. Further work to improve the efficiency of this procedure has been identified. Key words: Flotation testing, Flotation

Jan 1, 2010

By N. O. Lotter

The reliability of a set of flotation results is key to minimizing project risk either at concentrator commissioning, or at the point of implementing an improvement to an existing concentrator operation. High-Confidence Flotation Testing was developed for this purpose, and is part of the list of technologies of various scales used by Xstrata Process Support (XPS) in addressing these projects. The methodology is based on two principles: one, to ensure that the ore sample is representative and has been well-blended and subsampled; two, to perform the flotation tests in sufficient numbers of replicates with appropriate quality controls, so as to improve the reproducibility of the test data. Across ten years of practice and continuous improvement with this methodology at Xstrata Process Support, Sudbury, several improvements to this method and complementary connections into sampling and quantitative mineralogy have been developed. Two case studies are reviewed. These show the capability of this system in both optimizing an existing concentrator operation and in serving a new mine scenario. Further work to improve the efficiency of this procedure has been identified.

Jan 1, 2009

By Thomas Oberndorfer

INTRODUCTION Since several years the author is engaged in research activities in the field of mining method modelling (Oberndorfer, 1993 and 1994). The initial goal was to improve and assist the selection of the most appropriate mining method. However during investigations it became obvious that the most beneficial application of computer support is the fast calculation of numerical assessment rather than the consideration of all, i.e. also qualitative, criterions necessary for final decision. Numerical results serve - together with qualitative considerations based on the experience of the mining engineer - as a basis for decision. The emphasis is on "fast" calculation, as only this property makes it possible to calculate and compare many distinct variations. As long as no procedure exists, which optimizes all involved parameters, calculating many variations is of great important, because it is the only way to increase the chance to pick a alternative "close to optimum", but also to learn about the sensitivity the result will react on changes of input parameters, which are rarely known exactly. Generally speaking many trials give a better basis for final decision. It is no secrete that the most important obstacle towards quick calculations of a series of alternatives is not the processing time of the computer, but the time required for setting the input data in way that the computer can start processing, which is usually inter- active man work on the screen. Furthermore usually several distinct programs are required to cover the whole range of involved problems, with corresponding problems in automatic data transfer. The research work's goal was to overcome these problems. The approach developed was to describe a mining method more in a theoretical way (i.e. to give the computer some degree of "consciousness" on mining methods), which then can be applied under any specific conditions. E.g. a cut-and-fill operation will be "generally" the same in narrow or thick deposit areas, but the resulting keyfigures, e.g. total tonnage, productivity, dilution and loss, or finally costs per ton, will differ significantly. The approach (MMM = mining method modelling) presented reflects a deduction from the general case to a specific one (rather than the other way round). The developed model is general enough to be applicable to any mining method, and also to any degree of precision the mining method should be described, contrary to programs designed for specific mining method layouts which can be adjusted in a more or less wide range. PROGRAM DEVELOPMENT The principle correctness and feasibility of the approach was proved by a prototype program. However this program was more on a research level and far away from application for "real world" problems. The reason for this was, that it was regarded wasted time to re-invent certain tools, e.g. geometry intersection, deposit modelling or visualization. Hence it was tried to attract several software producers to invest in finalizing the model. Unfortunately this endeavor was not successful. Despite this defeat - and after some months of resignation - a final start on the project was decided. he reason for this decision was not at last the research activity in respect of low-cost underground mining methods for bulk- material as a substitute of typical quarry operations due to environmental restriction. This research work - which is in particular important for Austrian mining activities in beautiful and touristically used landscape - requires a lot of calculations in the way described. Both are still in state of progress, but - regarding mining method modelling - preliminary results can be presented. A complete re-programming of the program was required. Most obvious are the changes of programming language and operating system environment. Instead of Pascal under DOS C++ under MS-WindowsNT is now used. Several problems could be solved by this, in particular memory management, device drivers for input/output, and user friendlyness by up-to-date windows technology. However also more basic structures were changed. The idea was to utilize as many existing commercially available programs as possible to minimize programming efforts. WindowsNT helps already a lot by MFC technology, but also due to its multi-task facilities. This feature allows to run simultaneously several pro-

Jan 1, 1996

By Chris J. Conway, Bruce W. Atkinson, Graeme J. Jameson

The flotation of coal in the fie and coarse particle size ranges presents particular problems. Fine or ultra-fine coal less than 100 microns presents a challenge to conventional flotation machines because the rate of capture of the coal particles can be very low, so longer residence times are needed. Also, conventional mechanical cells are not normally designed with froth properties in mind. Froth drainage may be inadequate, leading to excessive entrainment of ash. The upper limit of flotation of coal is normally put at about 500 um (30 mesh). It appears that, in mechanical cells, coarser particles tend to be torn away from bubbles in the turbulent environment created by the impeller. In this paper, results are presented from plant trials of a high-intensity flotation column of novel design, namely the Jameson cell. Extensive trials have been conducted on coal slurries with a top size of around 1 mm. Size-by size analysis shows that it is possible to achieve high yields of low ash product over the whole particle size range.

Jan 1, 1995