Search Documents

By Ryan Lemmon

Belt turnovers are commonly used in conveyors to rotate the belt so that the clean side of the belt contacts the return idlers. The belt turnover length has traditionally been sized on only the twisting stresses. However, belt turnovers are also subjected to bending stresses due to the weight of the belt. Although bending stresses have in the past been ignored, these stresses are significant and should not be neglected. This paper quantifies and presents a method for calculated twisting and bending stresses and also the belt sag.

Jan 1, 2002

By Stephen D. Schwochow

Aggregate producers nationwide well recognize the numerous problems often faced in securing local approval to open and operate new gravel pits and rock quarries. Similar problems are faced in Colorado, but this region also presents certain political, social, and geological complexities that have become particularly troublesome in the last 10 years. The gravity of the local permitting dilemma can be related directly to the worsening supply-demand imbalance for aggregates in the state's most populated area, the Front Range urban corridor, particularly the Denver metropolitan area. The drive to develop crushed-rock reserves to supplement dwindling alluvial supplies and to meet increasing regional growth demands was somewhat predictable but perhaps more a "last resort" alternative forced onto producers by a hesitant and often apathetic government.

Jan 1, 1982

By Yi Luo, Jianwei Cheng, Mingming Li, Lei Xiao

Concealed thermal events in longwall gobs present safety hazards for underground coal miners and can significantly interrupt mining production. The probable causes for such thermal events range from coal oxidation at slightly above ambient temperature to smoldering fires due to spontaneous combustion of the broken coal left in the gobs. Locating such “hot spots” is the key step for planning and implementing mitigation measures to bring such thermal events under control. If a mine section, or even an entire mine, has to be sealed, understanding the status of the sealed mine atmosphere is important for the decisions guiding subsequent actions. The gas composition data obtained through the tube bundle mine atmospheric monitoring system is firsthand information of great value. Fire ratios proposed by various researchers and derived from gas composition data are useful in determining the fire status and even approximating the source locations (Timko and Derick, 2006). However, the applicability of each of these ratios under particular conditions should be carefully evaluated. The use of properly combined fire ratios can enhance the certainty of analysis. The explosibility of a sealed mine atmosphere deserves primary concern for safety reasons during seal construction, idle time and reopening of the sealed area.Mine atmospheric monitoring data from a longwall mine with flame fire have been analyzed. Efforts have been made to identify the possible causes, locations and statuses of these events using the obtained gas data, as well as other ventilation, geological and mining parameters. The effect of injected inert gas to control the events has also been quantified. The explosibility of the sealed atmosphere has been determined using two methods.

Jan 1, 2012

By R. R. Unterberger

This paper addresses the problem of seeing into rock. We will consider two methods, first to use radar, or electromagnetic wave pulses, to probe into rock ahead of mining and second to use sonar, or sound wave pulses, to probe into rock. Both are non destructive and capable of giving information on hazards ahead of mining. Such hazards might be a borehole full of water possibly leading to a high pressure aquifer somewhere above the mine level, changes in rock type, or the edge or top of a salt dome. Most of the work described in this paper deals with probing through rock salt which we have done successfully to over 2000 meters maximum range. We discuss first the radar probing and then the sonar probing. RADAR PROBING OF ROCK SALT Theory All electrodynamics are based on Maxwell's equations, which are in vector form [D = P (1) •B = 0 (2) aB V x E _ -(3) at aD •x H = J + - (4) at] where D and E are the electric displacement and electric field intensity vectors respectively, B is the magnetic induction or flux density

Jan 1, 1979

By Leo Langland

One of the primary functions of the Geotechnical Services-Materials section of the Arizona Department of Transportation (ADOT) is locating, sampling, and evaluating potential aggregate deposits throughout the State. This information is essential in designing, estimating, and bidding highway construction projects. The nature of materials used for aggregate varies greatly within Arizona. The northeastern or plateau section is famous for its scenic sedimentary formations that are, how- ever, too soft to make suitable aggregate. Volcanic materials are widely used in place of more conventional geologic units. In contrast, the southwestern, or Basin-and-Range section, contains a relative abundance of good aggregate, especially a diversity of gravels. The paper will review the off ice, field, and laboratory methods used by the ADOT Materials Section in satisfying its needs for aggregate information in Arizona.

Jan 1, 1987

By Slobodan Vujic

Production of building materials such as are stones, sand, gravel etc., is characterized by a relatively low economic value and requires reasonable transport costs. That is why we are often faced, in our practical work, with the fact that within the framework of a relatively small area several open pits of building materials are, developed side by side while neither ecological, urban and spatial nor location factors have been taken into consideration. Numerous locations together with heterogeneous factors. point undoubtedly to the problem of planning the open pits locations for building mateials as a very serious and complex one. Even when certain localities are in question, it is rather a difficult task to present a real state and encompass all the, important location factors by mathematical model ling. This paper presents one of such models for solving the problem of selecting a location for building materials open pit.

Jan 1, 1992

By Ugo Preti, Gianfranco Ferrara, Mark C. Williams, Thomas P. Meloy

Theoretical and experimental lockedness profile curves are the same when the model assumptions are met. They appear different because of the way the data is presented. Continuous theoretical lockedness profile curves present all the data, including the wings of the curves giving them the deep U-shaped configuration. Experimental lockedness profile curves, because of the measurement methods, are discretized, obscuring the wings. If the continuous theoretical curves are discretized, they are similar to the experimental curves. When a float sink test is used to measure an interval of locked particles, the integrated averaging of the separation process obscures the wings of the continuous theoretical curve. To disclose the wings with experimental data, narrow density or measurement intervals must be used.

Jan 1, 1992

By Shigeru Sarata

Working places in underground mines are formed by digging. The main feature of underground working places is that they are surrounded by rock. Digging through rock, which is main operation of mining, generates great reacting force. In many cases, supports are required to maintain a roof. Working places change their location with progress of mining operation. Therefore, for automate the work in such environment, a locomotive mechanism which can endure great reacting force, can support effectively the roof and floor, and has high moving performance in rough environment, might be required. In narrow underground environment which is surrounded by rock, it is possible to generate great fixing force by means of a jack which is set between the roof and floor or both side wall it is usual to apply a jack as anchor post for fixing machinery or reacting force. Self advancing supports widely used in long wall faces in coal mines could be said an example of locomotive mechanism with propping up fixing method. However it is difficult to say that ordinary self advancing supports have enough adaptability for various condition of the roof and floor. New locomotive method for underground working place 'Swing Phase Locomotion' is proposed. It is achieved by mechanism based on frame type support and synchronous control of jacks. Furthermore, to achieved high adaptability to various conditions of the roof and floor, another walking mechanism has been developed. The mechanism employs propping up jack as its legs.

Jan 1, 1989

By James N. L. Lukanuski

Three porphyry copper districts in southern Arizona are partly overlain by post-ore fanglomerates which share certain physical and petrologic characteris¬tics and which may comprise a distinct and significant class of rock. These units are the Locomotive fanglomerate of Ajo, the Helmet fanglomerate of Twin Buttes-Mission-Pima, and the Cloudburst formation of San Manuel-Kalamazoo, termed "Locomotive-type fanglomerates" herein. Post-ore units at Poston Butte and Lakeshore, Arizona, and Sar Chesmeh, Iran, also appear to fit this class. "Locomotive-type fanglomerates" are composed of poorly sorted conglomerates, lenticular sandstone beds, andesitic to rhyolitic flows and tuffs, and unique monothologic landslide breccias. They contain fragments of holyokeite - - a rare oligoclase lava of porcellaneous appearance. Their basal contacts are considered to be depositional and overlapping, sometimes complicated by later low-angle faulting. They arc quite different than the younger Cila, Pantano, and most "Whitetail" alluvial beds, and the older Amole, Recreation, Claflin Ranch, etc. elastics; in particular they are thinner and less widespread. Their ages are Eocene to late Oligocene. "Locomotive-type fanglomerates" may be genetically related to porphyry coppers as products of subsequent differentiation and volcanism, and sedimentation in short-lived basins of restricted area and extreme relief. They might be utilized as reconnaissance guides to target areas and as structural guides within target areas in the southwestern U.S., Northern Mexico, and elsewhere.

Jan 1, 1975

By W. A. Hoyer

Neutron activation analysis for mineral identification has attracted the attention of numerous investigators, judging from the publications on this subject in the past few years. 1-9 The appealing aspect of this method of mineral analysis is its proven sensitivity in the laboratory. In principle, activation analysis is one of the few petro-physical methods whereby a direct analysis for a mineral itself is possible in a borehole. The successful application of activation analysis requires the use of particular neutron reactions, measurement of selected gamma-ray energy intervals, and optimum bombardment and detection times. For copper analysis, Labanov et al., 10,11 using a low-energy PuBe source, reported an acceptable logging means. On the other hand, Pradzynski12, in analyzing ores and process tailings, used high-energy neutrons and photons for surface measurements of process samples. The work of Labanov et al. was based on measuring the rate of decay of the activated copper and hence was not as definitive as might be desired. Equipment is commercially available to carry out activation studies in the field 13,14 Gamma-ray spectra can be successfully transmitted over ordinary logging cables and, with borehole high-energy neutron accelerators and lower-energy chemical neutron sources, a variety of neutron activation methods can be studied. The purpose of the study discussed in this paper was to determine the feasibility and practicability of logging for copper using neutron activation techniques and commercially available equipment. The laboratory study showed that Cu could be detected in rock samples in the laboratory by high-energy neutron activation of 63 Cu. In the field, however, due in part to the large volume irradiated, the direct detection of copper using high-energy neutrons was not as promising. Detection of copper by measuring both the direct gamma-ray emission and the excessively strong low-energy gamma-ray absorption appears promising. Copper was not detected either in the laboratory or

Jan 1, 1972

By M. Sengupta

Surface mining in arctic regions is characterized by many unique problems. Continuous and discontinuous permafrost (perennially frozen ground) occurs in most of the arctic and subarctic areas. Permafrost presents special problems of slope stability. Stability of permafrost depends on its temperature, moisture content and material type. Permafrost slope fails due to solifluction, disturbance of ice rich slopes, and liquefaction. Drilling and blasting of frozen ground present special problems. Depending on their degree of saturation with water, freezing soils and rocks have a number of important characteristics that affect blasting efficiency. Metals used in mining equipment and mining structures require special selection. At low temperatures many steels lose most of their normal ductility and toughness (resistance to brittle fracture). The paper discusses engineering solutions to unique problems of arctic mining.

Jan 1, 1986

By Kurt Zeidler, Vojtech Gall

London Underground Limited are currently constructing an extension of the Jubilee Line. The approximately 16-km long Jubilee Line Extension Project connects the existing Green Park Underground Station with the Canary Wharf area and Greenwich. Being a part of the project, the London Bridge Station (Contract 104) was built using a combination of the New Austrian Tunneling Method (NATM) with Compensation Grouting. NATM was successfully applied in softground and urban areas under restrictive requirements regarding settlement limitation. Information on the flexibility of the method and the influence of Compensation Grouting on ground and tunnels are given.

Jan 1, 1997

By O. E. Wheeler

The use of the walking dragline as a stripping tool has increased dramatically in the past two decades. The reasons for its increased popularity and some historical background on its introduction into the mines are given in a recent paper by Learmont. (l)* The history need not be recounted here except to show the trend to longer booms which has accompanied the growth in machine size. Figure 1 shows the change in maximum operating radius on Bucyrus-Erie machines which has occurred over the years and Figure 2 shows the corresponding change in maximum boom lengths. Reference 1 also presents some of the reasons for expecting this trend to longer booms to continue. There are many design parameters affected by the increase in boom lengths; swing power, hoist and drag rope lengths, and drum capacity, to list just a few. The purpose of this paper is to discuss only the structural implications of using longer booms. As in the design of any structure, the various facets of boom design are interrelated and a process of optimization between them must be worked out either by evolution or by conscious iterative effort. The decisions we have reached about such things as material selection, structural arrangement, and applicable criteria, have not come into being overnight but represent instead many years of design experience and a fair amount of recent concentrated analytical effort. In the following pages an attempt will be made to first, state those decisions, second, explain how we arrived at that particular result; and third, describe what we expect future developments to be which might influence us to change those decisions.

Jan 1, 1976

By Charles LeMoyne

The Cable belt Company has been building single flight conveyors for a number of years. The simple design concepts of this type conveyor, introduced over thirty years ago, when distances of one to two miles were considered major advances in technology, remain relatively unchanged. Conveyors that are 6 to 20 miles (9.0 to 32 kilometers) long are being built and are presently in operation through- out the free world. The Cable Belt conveyor is not conventional in its construction. Cable welt differs from conventional troughed idler conveyors in that the driving medium and carrying medium are separated. Motion is provided by two endless steel cables running the length of the conveyor. The cables are driven by a single drive unit incorporating a differential gear which insures identical cable linear speeds and equal tension in both cables at all times. The belting is located and supported by "V" shaped shoeforms moulded to the belt which form a wedging action. The friction between the belting and rope is sufficient to prevent slippage (See figure 01).

Jan 1, 1983

By Siegmund Babendererde

1. Introduction In Sayreville, New Jersey, the Middlesex County Utilities Authority put the construction of a 1041 m long sewer outlet to tender in June 1989. It had an internal diameter of 3,36 m and was part of a sewage treatment works project for county Middlesex. The contract was awarded to the Lodigiani Company, USA, who employed Hochtief Incorporated as subcontractor to drive the sewer outfall. 2. Ground Conditions According to the preliminary geological site investigation, carried out by the consultants Metcalf & Eddy, the tunnel passed through marine deposits.

Jan 1, 1991

By P. E. Snoek, R. L. Gandhi, C. S. Miller

Slurry operations are an integral part of mineral processing. There is therefore reason to consider using slurry pipelines for long distance mineral transportation. This paper reviews the current state-of-the art of such systems and, in particular, the design factors which must be addressed. It also discusses the selection of major components such as pipe, pumps, valves and storage facilities. Finally, the major steps required to determine the economic feasibility of a slurry system are listed and the major advantages and disadvantages of slurry pipelines compared with other forms of land transport are summarized. SLURRY PIPELINES: GENERAL OVERVIEW Minerals Transported Long distance slurry pipelines have been successfully used for transporting coal, iron concentrate, copper concentrate, limestone and phosphate. Additionally, several tailings disposal pipelines of considerable size and length have been built, but these generally are not categorized as long distance commercial mineral transportation systems. Table 1 lists selected examples of commercial slurry pipelines.

Jan 1, 1986

By Karin Bäppler

Mechanized tunnelling is undoubtedly one of the most innovative disciplines in the international construction industry. Technological progress in the planning and production of most modern infrastructure is constantly striving for new records on basis of highly specialized solutions and know-how. Humans and technology have accomplished excellent achievements over the past few years in varied, difficult terrain. New length records are being set with the 64 km long Brenner Base Tunnel and the HS2 Railway system currently under construction in Europe. Cities are building ever longer and more demanding sewer tunnels. The paper highlights some of the challenges, trends and innovations of long-distance tunnelling projects.

Dec 1, 2022

By Christian Heinz, Doug Harding

TBMs can last for decades and be rebuilt project after project with proper maintenance. How successful can rebuilt TBMs be? At the DigIndy Tunnel System in Indianapolis, Indiana, USA, a rebuilt TBM was used to great effect. The 6.2 m diameter Main Beam, originally manufactured in 1980, bored 40+ km of tunnels and set three world records in its size class of 6 to 7 m, including a best month of 1,754 m. In this paper, the authors analyze the TBM rebuild, performance and lessons learned to make recommendations for future projects seeking to use rebuilt TBMs over long distances.

Jun 23, 2024

By N. Gritzuk

The area of Canada with which we are here concerned consists of Yukon Territory and Northern British Columbia. Generally it lies west of the coastal mountain range and access to the sea can be gained at only selected points which are relatively few. It is served by the Alaska Highway as well as a provincial and territorial system of roads permitting transport of mining products to Whitehorse in Yukon Territory. This town it the northern terminus of the White Pass and Yukon Route, which system provides a rail service between Whitehorse and Skagway, Alaska a distance of 110 miles, and thence to Vancouver, British Columbia, by the coastal Motor Vessel C. J. Rogers, a distance of an additional 890 miles. At present the service between Vancouver, B.C. and Whitehorse, Y. T. is on a fourteen day basis. The coastal vessel, capable of carrying 3,200 tons of cargo, was specially designed and built in 1955 for handling containerized cargo and general cargo northbound, and containerized and palletized asbestos fibre, and palletized lead and zinc concentrates southbound.

Jan 1, 1961

By J. D. Grenia

The Buick Mine is a joint venture of American Metals Climax, Inc., and Homestake Mining Company located 120 miles by road southwest of St. Louis, near the village of Boss, in the 'New Missouri Lead Belt' (See Figure 1). Since start-up in 1969, over four million tons of lead-zinc ore have been mined and milled at Buick. Situated about 1,100 feet below the surface at an elevation 270 feet above sea level, the flat lying sinuous ore bodies are up to 250 feet wide, 85 feet high and several thousand feet long. Mineralization is galena, sphalerite and chalcopyrite in dolomite, Access to the mine is through two 18'Ø concrete lined vertical shafts - one for servicing and the other for hoisting ore (See Figure 2). The mine is being worked by a modified room and pillar method using both rubber tired equipment and a sub-level rail haulage. Ore is broken from first pass headings, back and bench faces and transported by load-haul-dump units to ore passes located on 900 foot centers. The ore is pulled from chutes on the sublevel 90 feet below into 15 ton bottom dump cars and delivered in 10 car lots by a 15 ton diesel locomotive to a 42" gyratory crusher (See Figure 3). A recent innovation has been the introduction of two 50 ton trucks with plans to haul up to 60% of the ore on the mining level to an ore pass feeding directly to the primary crusher (See Figure 4). Ventilation raises up to 16'Ø, which were originally planned for 900 foot centers, are now driven on 450 foot centers.

Jan 1, 1973