Search Documents

To gather additional field data from the western United States, researchers from the National Institute for Occupational Safety and Health (NIOSH) installed an array of field instrumentation at a longwall coal mine in Central Utah. The purpose of this field site was to monitor ground movement and changes in pressure during mining where conditions include massive, stiff overburden and relatively deep cover. To accomplish this, field instrumentation was installed in the two-entry gate road between the fifth and sixth longwall panel in the current mining district.

Jan 7, 2020

By Bahne C. Cornilsen, X. Shan, David H. Carlson, John H. Johnson

The air in three U.S. underground coal mines has been sampled. The data developed show the relative importance of the various pollutants and quantify the need for control. Total respirable particulate matter (TRPM) was found to be the critical pollutant (the one requiring the most dilution for control). TRPM is considered to be "respirable coal dust" by procedures approved for sampling in U.S. underground coal mines. However, this "respirable coal dust" also includes diesel particulate matter (DPM) and particulate from other sources. While "respirable coal dust" was the critical pollutant, Raman spectroscopic analysis showed that more than half of this "respirable coal dust" was DPM. The DPM in the samples ranged from 22 to 152% of the 2 mg/m3 limit for respirable coal dust. Thus DPM was the critical pollutant using the 2 mg/m3 respirable coal dust limit. SO2 gas produced by the combustion of diesel fuel containing sulfur was the second-most critical pollutant. Characteristic curve slope (CCS) values were calculated to determine the quantitites of the various pollutants generated per unit of diesel haulage activity. Mine 1 had the highest TRPM CCS values with 29 mg/m3/%C02 for the Ramcar and 57 mg/m3/%C02 for the Haulageway location. The highest coal particulate CCS measured was 30 mg/m3/%CO2 and the highest diesel particulate CCS measured was 27 mg/m3/ %C02. Both of these high values were measured in the Mine 1 haulageway location. Calculations were made to determine the controlling CO2 concentrations (CCC) at which all other measured pollutants would be within their limits. These CCC values, which, for the mines sampled, were based on TRPM, varied from a low of about 0.07% for the Mine 1 haulageway location, to a high of about 0.15% for the Mine 2 Ramcar and haulageway locations. Weekly average CO2 concentrations measured in these mines ranged from 0.09 to 0.11 % for the Ramcar, from 0.05 to 0.09% for the haulageway, and from 0.08 to 0.11 % for the return. The concentrations of TRPM ranged from 1 and 2 mg/m3 in mine areas frequented by personnel, and to greater than 4 mg/m3 in returns where personnel are not exposed.

Jan 1, 1991

By Zhe Wang, Tichang Sun, Yongqiang Zhao, Zhengyao Li

Coal-based reduction followed by magnetic separation is a promising technology for processing refractory iron ores. Analysis of the size distribution of metallic iron particles is an effective approach for exploring the mechanisms of coal-based reduction. As metallic iron particles exhibit very complex shapes compared with nature ores, approaches for measuring and characterising metallic iron particles still remain unclear. In this study, the size of metallic iron particles was measured and characterised using manual point-counting by optical microscopy technics and image analysis. The effects of CaF2 as an additive on behaviour of the particle size distribution (i.e. mean size and cumulative frequency distribution) were also determined. Results indicate that CaF2 had a significant effect on the growth of metallic iron particles. When the CaF2 dosage increased from 0 to 8%, the mean size according to the area method increased from 9.03 to 16.28 μm, while the promotion effect gradually weakened and generated many fine metallic iron particles when the CaF2 dosage exceeded 8%. An increase in CaF2 dosage also led to cumulative distribution curves gradually shifting to the right mainly because F− can break the crystal structure of each phase during the carbothermic reduction of titanomagnetite and reduce the stability of the lattice structure, thus reducing the melting point and accelerating the growth of metallic iron grains. Compared to different measuring methods, the area method is a more suitable approach for measuring and characterising the size of metallic iron particles.

Sep 18, 2020

By Richard A. Williams

The design, modelling and simulation of solid-liquid mixers remains one of the least advanced aspects of minerals processing, due to difficulties in quantifying complex slurry hydrodynamics from first principles, and in acquiring reliable experimental data for model verification and development. This contribution describes the application of electrical resistance tomography (ERT) for three dimensional imaging of the concentration of mineral particulates in a slurry mixer as a function of key process variables (particle size, impeller type, agitation speed). It is demonstrated how ERT can provide a wealth of detailed data to allow model development, which ultimately will lead to much improved design capabilities and the generation of mixing models which could reside within Particle Process Simulators. This principle is illustrated using descriptions of mixer behaviour based on an empirical approach, although the measurement methodology described is equally suited to development of computational fluid dynamics models, cellular models or design approaches based on artificial intelligence. The experimental data can be built into a visualisation data bank, which acts as a "process toolkit" by allowing a library of process responses to be catalogued. Hence these data can be accessed for the purposes of model development, equipment selection, optimisation of operating conditions or testing on-line control strategies.

Jan 1, 1995

By D. S. Choi

The paper contains a subsidence measurement taken over a room and pillar panel of a mine located in northern West Virginia. A total of 72 monuments were used to determine a three dimensional view of mine subsidence. In addition, the results of measurements were used to compute ground strains with the use of a numerical model.

Jan 1, 1982

By Carl E. Brechtel, Edward D. Thimons

Providing adequate airflow to effectively dilute and remove diesel pollutants in large mine working headings is a little researched area. A simulated diesel mucking operation was carried out in the Exxon Colony Pilot Mine in Colorado to establish expected levels of diesel pollutants in dead-ended working headings. This heading was nominally 15.3 m (50-ft) wide by 9.2 m (30-ft) high. Two face ventilation systems were tested using sulfur hexafluoride tracer gas to represent the diesel pollutants. The results of these tests showed that conventional face ventilation systems operating at high flow rates could adequately ventilate diesel equipment in the 447-522 kw (600-700 hp) range, even in a dead heading 91.4 m (300 ft) in length.

Jan 1, 1987

By M. J. Senk, A. Lusin

Federal regulations require that methane liberated at the face be diluted and removed to maintain methane gas concentrations below 1pct (CFR) in working places and intake air courses. The delivery and distribution of intake air at the face is critical for effective face ventilation. Improved techniques for monitoring the movement of intake air to the face are needed. A test system was developed and a computer program written for using a three-axis ultrasonic anemometer to measure airflow in a simulated mine entry. Results of tests conducted in the entry showed that the anemometer is a valuable tool for measuring mine airflow conditions near the face.

Jan 1, 2003

By Michael J. Martinson, John R. Larsen, J. Warren Andrews

Measurements reported in the paper were recorded in an active Green River, Wyoming, trona mine, partly as a teaching exercise and partly to provide the mine in question with additional input data for its ventilation network program. Measurements were made: - in representative three-entry intake airways in room and pillar sub-mains; - between the lower portion of a vertical down-cast hoisting shaft and the start of an intake airway system established in a room and pillar main; - in a representative downcast section of a divided vertical shaft, and of the collar entrance loss at the top of the same compartment. Pressure differences were measured with manometers and trailing hoses, air flowrates with calibrated anemometers, and barometric pressures and wet-and dry-bulb temperatures were recorded for density determinations. Where possible, results are quoted as Atkinson friction factors, and relevant measurements are recorded in some detail to show the magnitude of fluctuations in observed pressure differences.

Jan 1, 1987

By M. Paventi, M. J. Scoble, B. B. Mohanty

There is no straightforward and systematic method for adequately measuring blast damage in on-going mining operations. This paper considers various techniques available for the measurement of blast damage, making particular reference to recent underground hardrock mine studies. This paper concludes by indicating the importance of understanding and accounting for geology and emphasizes the need for a robust damage-audit procedure.

Jan 1, 1998

By M. J. Scoble

There is no straightforward and systematic method for adequately measuring blast damage in on-going mining operations. This paper considers various techniques available for the measurement of blast damage, making particular reference to recent underground hardrock mine studies. This paper concludes by indicating the importance of understanding and accounting for geology and emphasizes the need for a robust damage-audit procedure.

Jan 1, 1997

By F. C. Schwerer, C. R. McKee, J. C. Seccombe

Production of methane from coal seams requires hydrofracturing, and the length of a hydraulic fracture determines we11 spacing. Since the volume of fluid injected is known, the fracture length is the volume divided by average width and height. If the fracture is contained in the known height of the seam, then fracture width becomes the major factor con- trolling length. Width is proportional to coal compressibility; bulk compressibility is known to be larger than intrinsic compressibility. A method is given here to measure in-situ compressibility (a) from transient pressure testing. Theory linking flow in porous media with rock mechanical properties is reviewed. A consistent derivation of the porous flow equation is given incorporating 3-D deformation and the effective stress parameter "st' linking changes in effective stress and pore pressure. The relations for "st' in terms of a and intrinsic compressibility (ai) are substituted into the field measured porosity-compressibility product (net) and solved for a, the constrained matrix compressibility. In a field example, using 4 wells with an anisotropic analysis, the ratio of major to minor permeability was 17 for the Pratt A seam. a was found to be 6x10-5/psi as opposed to the laboratory value of 1.4x10-6/psi.

Jan 1, 1986

By D. H. Carlson, J. H. Johnson, C. F. Renders

Research was conducted at a western coal mine on a wide variety of underground mining vehicles to develop testing procedures for portable instrumentation monitoring of tailpipe concentrations of diesel particulate matter (DPM), carbon dioxide (CO2) carbon monoxide (CO) and nitric oxide (NO). DPM was measured using the Emissions Measurement Appa¬ratus (EMA) developed by Michigan Technological University (MTU), and an ECOM-KL five-gas analyzer was used to measure gaseous tailpipe concentrations. Baseline concentrations of the tailpipe pollutants were measured using vehicle systems to load the engine. Concentrations before and after the water scrubber were measured and water scrubber efficiencies were estimated by calculation. Field measurement procedures were established. Heavy-duty vehicles with automatic transmissions were loaded using the torque converter to stall the engine. Consistent engine loading for light-duty vehicles with manual transmissions involved placing the transmission in neutral and adjusting the throttle to maintain a constant engine speed of 2,500 rpm. Tailpipe CO2 concentrations for Caterpillar 3306 and 3304 engines were compared to laboratory CO2 data from Caterpillar and MSHA to help determine if engine settings were correctly adjusted for operation at high altitudes. (Perfect agreement between the mine vehicle tailpipe and laboratory measurements would not be expected because of the differences in the test conditions.) DPM concentrations for light-duty vehicles ranged from about 20 to 160 mg/m3, and one light-duty vehicle averaged near 1,000 mg/m3. DPM concentrations for heavy-duty vehicles ranged from about 55 to 200 mg/m3. Widely ranging DPM concentrations for a particular vehicle type reflect the state of maintenance, fuel rate settings and different engine loading procedures as well as differences between samples collected upstream and downstream of the waterscrubber. The calculated DPM removal efficiencies due to the water scrubber varied considerably between vehicles, ranging from 13% to 51%. Calculations indicate that, under worst-case conditions, very large reductions in DPM may be required to meet the proposed DPM PEL of 0.15 mg/m3, even on vehicles with water scrubbers. In-mine ambient air studies, which are needed to actually measure the impact of the tailpipe concentrations on the work environment and the effect of mine ventilation on the dilution of DPM were not done in this first set of tests.

Jan 1, 2000

By J. G. Smith, L. P. Sheets

Introduction Potential applications that exploit the electrical properties of coal measure rocks include: (1) radar sensing of coal face, floor, and roof for automated mining operations; (2) underground wireless communications; and (3) sensing extent of subsidence, blasting operations, coal gasification bums, and moisture migrations. Impediments to exploitation of electrical properties include: (1) a lack of reliable electrical properties data for in situ conditions and (2) a lack of correlation data between electrical properties and other relevant physical properties. In this paper data are presented for electrical conductivity and permittivity for Appalachian and Illinois shales for a frequency range 2 x 10 to 2 x 10 Hz. These data are useful in establishing in situ electrical property variability, lower limits, and anisotropy. Electrical proper¬ties measurement and values for other coal measure rocks are discussed as well. Laboratory measurement For the frequency range investigated, a capacitance bridge and Q-meter were employed. These instruments are designed to yield bulk values of permittivity and conductivity. Disk samples of thickness 0.396 cm (0.156 in.) and diameter 2.54 cm (1 in.) were machined from cores obtained from the two coal basins. While both the capacitance bridge and the Q-meter must be balanced manually, the bridge has an analog-to-digital interface and an attached computer specifically designed to expedite data collection and interpretation. Sample holders are critical components in the measurement process. A Hartshom-Ward holder was employed with the bridge and a Marconi micrometer jig was used with the Q-meter. Neither commercial sample holder was designed to regulate ambient humidity conditions. Because water adsorbed on sample faces may cause errors approaching 100%, special enclosures were designed for both holders. Each enclosure contains a flush-mounted externally-manipulable carousel, an externally-manipulable rigid arm that can accomodate translational motion and three-dimensional rotation, a compartment for humidity regulating solids or liquids, and a humidity sensor. Each enclosure will accomodate several samples that can be manipulated within the enclosure without opening it. Experience gained during this research demonstrated that humidity regulation was necessary to obtain repeatable results. Grinding and polishing shale to a very thin thickness (about 0.4 mm) was shown to cause changes in electrical properties as well. These latter changes were attributed to alterations in the water content. Theoretical considerations A very comprehensive discussion of the electrical properties of sedimentary rocks is available in literature (Sen and Chew, 1983). These authors reviewed the work of others and proposed modifications to better explain the frequency dependent behavior of the permittivity and conductivity of rocks. A large portion of their article was devoted to explanations of large relative permittivities at low frequencies such as observed in this research. They noted that the electrical properties of formations containing shales and clays are the most difficult to explain. Sen and Chew noted the need for additional experimental data and further refinements in theory. Results Shales, limestones, and sandstones were examined for a single 150-m (492-ft) core from Pennsylvania and for a dark shale from a southern Illinois coal mine. Figures 1 and 2 illustrate the conductivities and relative permitivities for the southern Illinois dark shale at a single location. The differences in electrical properties clearly

Jan 1, 1987

By Elisabeth Tønnesen, Lloyd Tunbridge

"SUMMARY Injection grouting in rock around tunnels is used to reduce or stop water inflow. Little is known about the distribution of pressure within the rock mass during and after grouting. Instrumentation was developed to record pressure at the back of the packers inside the rock mass during injection grouting in order to improve our understanding of the process. Using this equipment measurements inside multiple injection holes during injection pumping have been made during several rounds of injection grouting in a tunnel. The data has been compared to the data recorded on the grout pumping rig and analysed to gain an understanding of the behaviour of grout injection process in the rock mass. The initial results are reported in this paper. INTRODUCTION Construction of a tunnel in soil or rock below the ground water table frequently results in the flow of ground water into the tunnel if the ground is permeable or fractures conductive. The injection of cement or chemical based grouts is frequently used during tunnel construction to reduce flow of water into a tunnel. Significant water flow into a tunnel is undesirable for several reasons: • there is a high cost in pumping out water over the lifetime of a tunnel; • drips and flows of water have to be diverted from the roadway or track; • where freezing conditions occur there is the possibility of ice build up and; • ground water levels may be changed possibly affecting surface water such as causing drainage of lakes and ponds, and changes in vegetation. Grout injection is most effectively done ahead of excavation to ensure that the grout penetrates the ground. Where heavy flows of water already occur into a tunnel the grout may be washed out before it sets. Normal practice in ground where water flows are encountered is to inject grout in a number of long holes ahead of the face with outer holes forming a ring around the proposed tunnel excavation – eventually forming a shield of grouted rock around the final tunnel, Figure 1. The holes may be sealed off a couple of metres into the rock with an expandable rubber plug around a pipe through which the grout can be injected, Figure 2. A one-way valve in the plug stops the grout from flowing back out of the hole when pumping stops and avoids grout flowing out through neighbouring holes. The rubber packer with a one-way valve permanently installed in the injection hole precludes the measurement of pressure down the hole when pumping is stopped."

Jan 1, 2016

By David J. Dunn

Of many physical parameters critical to design of grinding processes, impact of grinding media is among the most difficult to measure or predict. Yet impact of falling grinding balls, pebbles, or rods accomplishes the fine grinding essential to metallurgical recovery of most important minerals. Unfortunately, the same impacts that break ore fragments deform or crack grinding mill liners. A project was undertaken at Climax Molybdenum Company to measure impact forces in operating ball mills so that they might be used to calculate stresses in liner materials and be correlated with service performance of mill liner alloys. Towards that end, a method of measuring impact forces on ball mill liners using an instrumented grinding ball has been developed. Preliminary tests show that impact forces and contact stresses imposed on bare mill liners are quite high but are greatly reduced by cushioning when coarse ore particles are crushed between balls and liners. Compressive and shear stresses induced in liners not protected by coarse ore are so severe that deformation or minute subsurface cracking are inevitable in all but the small production grinding mills, regardless of mill liner alloy strength or hardness.

Jan 1, 1977

Because of its small interburden thickness, concentrated stress distributions, high coal seam metamorphism, and complex geological conditions, mining the five coal seams (Nos. 5, 7, 8, 9 and 12) of Kaiping coalfield is difficult. Kaiping coalfield is located within 80 m in the Kailuan Group. The overburden caving caused by mining the five coals seams was measured using ZTR12 geological penetration radar (GPR) survey combined with borehole observations. The development characteristics of full-cover rock fractures after mining were obtained from the GPR scan, which provides a measurement basis for the control of rock strata in close multiple-seam coal mining. For the first time, it was found that the overburden caving pattern shows a periodic triangular caved characteristic. Furthermore, it is proposed that an upright triangular collapsed rock pile and an inverted triangular area with larger fragments piled up alternately appear in the lower gob. The research results show that the roof structure formed in the gob area can support the key overlying strata, which is beneficial to ensure the integrity and stability of the upper coal seams in multiple-seam mining of close-coal seams.

Jan 7, 2020

By S. Helgen, C. Byrns, A. Davis

The 4000 acre historic Robinson Mining District outside Ely, Nevada hosts a continuum of oxidelsulfide waste rock dumps of different ages. In an effort to develop a paradigm to explain past, existing, and future conditions at the site profiles of oxygen, pH, temperature, and specific conductivity were collected from various waste rock dumps using a hand-driven soil gas probe and a down-hole sampling device. The resulting data are useful in interpreting the fate and manner of pyrite oxidation within the dumps and in identifying waste rock dumps that may require remedial measures compared to those that require only minimal action prior to closure.

Jan 1, 2000

By V. A. Leach, Lokan. K. H., S. B. Solomon, R. S. O’Brien, L. J. Martin, K. N. Wise

INTRODUCTION The development during 1979 of a relatively small, but high grade (10,000 tonnes uranium at an average grade of 2 per cent), uranium ore body at Nabarlek in the Northern Territory, Australia offered an excellent opportunity to obtain detailed radiation data for an open cut mine operating during the dry season. The ore body (Queensland Mines Limited-1979), which was completely extracted in a period of four and a half months, consisted of a vein type deposit dipping at 30 to 45 degrees and contained a central core of pitchblende in massive and irregular pods, surrounded by lower grade fine grained disseminated pitchblende. Mineralisation extended from the surface to a depth of 72 metres over a length of 230 metres with an average but variable thickness of 1D metres. Ore near the surface had been heavily weathered and complex secondary minerals were formed which had dispersed from the main vein. Mining was carried out with large earth moving equipment. Overburden and weathered surface ore were removed initially with scrapers. At greater depths bulldozers were used to rip and assemble ore and rock at each level, and these were removed by large trucks to the ore and waste rock stockpiles. Where necessary, blasting took place during shift changes each evening. Mining was essentially continuous with two ten hour alternating shifts working for thirteen days out of fourteen. At the completion of mining a relatively small excavation (335m x 185m x 70m) remained, and this will serve as a tailings repository during the milling phase. FIELD MEASUREMENTS The inhalation of radon daughters, arising from the radioactive decay of radon gas is well established (Archer et. al. 1973) as a potential hazard in the uranium mining industry. Control over radon and its daughters to ensure that recommended exposure limits are not exceeded is achieved by providing adequate ventilation, and under normal circumstances natural ventilation from an open pit should be sufficient. However, during the dry season it is not uncommon for stable atmospheric conditions, with little horizontal air movement, to develop - particularly at night - and significant radon daughter concentrations may accumulate. Throughout the entire mining period measurements were therefore made of radon and radon daughter levels at representative locations within the pit and on the ore stockpile as it developed. Initially these measurements were carried out manually, using the Rolle method for radon daughters, (Rolle 1972) and .scintillation cells (Lucas 1964) or a two filter tube for the determination of radon (Thomas 1970). For the latter half of the period however, a continuous recording instrument, developed within the Laboratory was used to provide a detailed record of radon daughter levels within the pit. At the same time, continuous readings of wind speed and direction, and vertical temperature gradient between 10 and 3D metres were recorded on a 30 metre meteorological tower, situated 800 metres from the pit. Radon Emanation Rates It is evident that radon and radon daughter concentrations depend on the grade, or more particularly, on the surface radon emanation rate of the ore which is exposed. Accordingly, as the mine progressed, detailed measurements were made of both of these quantities. The surface emanation rate of radon was determined for each ore bench as it was exposed by placing an extended array of canisters, filled with freshly degassed activated charcoal, face down on the ore for a known time. These canisters, which had previously been calibrated in the Laboratory, adsorb radon with high efficiency, and the total radon adsorbed is measured after retrieval by detecting the gamma rays from the trapped radon daughters (Countess 1977). At the same time, as each canister was placed in position, a measurement of the local ore grade was made for each location. This was achieved with a calibrated sodium iodide scintillation detector, adjusted to detect the 609 keV gamma ray from the isotope 2148i, a decay product of radium. Finally, measurements were made of the radiation field 1 metre above the surface, with a gamma ray survey meter, which was calibrated in the Laboratory. The relationship between the scintillator count rate and ore grade was determined by comparing the scintillator output with the gamma monitor, and relating the latter measurements to ore grade (Thomson and Wilson 1980). It was observed that while emanation rates and ore grades varied widely, the ratio of emanation rate to ore grade was in general fairly stable. A plot of this ratio is presented as a function of depth below the original surface in Figure 1. For most observations the ratio is constant at a value of 80 Bq m-2 s -1 per unit ore grade, where ore grade is expressed as percentage of U308. At the surface however, where the ore was weathered, the ratio was about a factor of three higher, and at two particular depths, where high grade pitchblende was being removed, it was very much lower. This was not unexpected as earlier Laboratory studies of drill core samples from Nabarlek had indicated that the emanation coefficient (the fraction of radon produced within the ore which escapes from the mineral particles) decreases with increasing ore grade.

Jan 1, 1981

By G. S. Dobby, N. J. Contini, S. W. Wilson

Scale-up and simulation of flotation columns requires construction of mathematical models which employ, as a minimum, rate constants for quantifying particle recovery in the collection zone as well as split factors for quantifying froth zone performance. To date, measurement of these rate parameters has proven to be difficult, due to the interdependent nature of the collection and froth zones. This paper describes a technique for making these measurements. The method requires recovery data from two modes of operation: countercurrent and cocurrent. In cocurrent flow slurry is fed at the bottom of the column and tailings are withdrawn a short distance below the froth interface. Countercurrent mode is conventional operation. The critical difference is that particles which are dropped out of the froth in cocurrent mode are immediately lost to tailings, while in countercurrent mode the particles are subjected to recollection. Fitting of the measured recoveries to the equations that describe flotation in the two modes yields rate constant or recovery values for both the collection and the froth zones.

Jan 1, 1988

By C. Zhou, R. Jacksha

This paper reports measurement results for radio frequency (RF) propagation around 90° corners in tunnels and underground mines, for vertically, horizontally and longitudinally polarized signals. Measurements of signal power attenuation from a main entry into a crosscut were performed at four frequencies — 455, 915, 2450 and 5800 MHz — that are common to underground radio communication systems. From the measurement data, signal power loss was determined as a function of signal coupling from the main entry into the crosscut. The resultant power loss data show there are many factors that contribute to power attenuation from a main entry into a crosscut, including frequency, antenna polarization and crosssectional entry dimensions.

Jan 1, 2016