Search Documents

By Eugie Kabwe

The effective employment of a pretensioned bolt within support structures requires an appropriate installation tension as a result of sufficient bolt head/nut preload. In this paper, a load indicator washer (LIW) able to withstand an assigned static loading as well as provide an appropriate pretension is presented. The different LIW breadths are numerically analyzed with ABAQUS finite-element code to estimate deformation when a designated 60 kN preload is applied. The numerical simulation employs the bilinear isotropic hardening constitutive law governed by the von Mises yield criterion. The simulation also considers the nominal temperature of the nut-LIW-rock bolt connection. Therefore, long-term relaxation effect on bolt pretension as a result of stress relaxation is neglected. The compressive force required to achieve the LIW predetermined deformation is the bolt pretension. It is drawn from the simulation results that LIWs with thicknesses of 1.5, 2.0, 3.0, 3.5 and 4.0 mm are completely flattened when subjected to 28, 42.5, 65, 76 and 88 kN preloads, respectively.

By Eugie Kabwe

Rock bolts are components of tunnel support structures and their efficacy in reinforcement requires the appropriate estimation of the bolt pre-tension. However, cases of ineffective rock bolt application due to loosening are common which leads to the potential failure of the support structures, thus negatively affecting the tunnel stability. The effective employment of pre-tensioned bolt within support structures requires an appropriate installation tension as a result of sufficient bolt head/nut pre-load. Henceforth, this paper presents a load indicator washer (LIW) capable of withstanding assigned static loading as well as provides an appropriate pre-tension. The different LIW breadths are numerically analysed in the finite element code (ABAQUS) to estimate deformation when a designated 60-kN pre-load is applied. The numerical simulation employs a bi-linear isotropic hardening constitutive law governed by the von Mises yield criterion. The simulation also considers the nominal temperature of the nutLIW-rock bolt connection. Therefore, a long-term relaxation effect on bolt pre-tension as a result of stress relaxation is neglected. The compressive force required to achieve the LIW-predetermined deformation is the bolt pre-tension. It is drawn from the simulation results that the 1.5-, 2.0-, 3.0-, 3.5-, and 4.0-mm-thick LIWs are completely flattened when subjected to 28-, 42.5-, 65-, 76-, and 88-kN pre-load respectively.

By Eugie Kabwe

Rock bolts are components of tunnel support structures and their efficacy in reinforcement requires the appropriate estimation of the bolt pre-tension. However, cases of ineffective rock bolt application due to loosening are common which leads to the potential failure of the support structures, thus negatively affecting the tunnel stability. The effective employment of pre-tensioned bolt within support structures requires an appropriate installation tension as a result of sufficient bolt head/nut pre-load. Henceforth, this paper presents a load indicator washer (LIW) capable of withstanding assigned static loading as well as provides an appropriate pre-tension. The different LIW breadths are numerically analysed in the finite element code (ABAQUS) to estimate deformation when a designated 60-kN pre-load is applied. The numerical simulation employs a bi-linear isotropic hardening constitutive law governed by the von Mises yield criterion. The simulation also considers the nominal temperature of the nutLIW-rock bolt connection. Therefore, a long-term relaxation effect on bolt pre-tension as a result of stress relaxation is neglected. The compressive force required to achieve the LIW-predetermined deformation is the bolt pre-tension. It is drawn from the simulation results that the 1.5-, 2.0-, 3.0-, 3.5-, and 4.0-mm-thick LIWs are completely flattened when subjected to 28-, 42.5-, 65-, 76-, and 88-kN pre-load respectively.

By K. Sasaki, T. Murakami, S. Akibayashi, Q. Wei

A numerical analysis and an experiment were done on groundwater flow past a bore hole with a cylindrical obstacle at its center. Flow around the obstacle in the bore hole was studied in detail. Two dimensional governing equations to simulate this flow were written for the hydraulic head and seepage velocity in a porous medium and for the vorticity, stream function, and velocity in the bore hole. These equations were non-dimensionalized and solved by using the alternating direction implicit and successive-over-relaxation finite difference methods. Flow visualization experiments and velocity measurements in the bore hole were done with a two dimensional model composed of a porous medium. The numerical analysis procedures were validated by a comparison of numerical and experimental results. Effects of the Reynolds number and obstacle size on flow in the bore hole are clearly shown in the velocity and streamline profiles. The quantitative relation between the seepage velocity in the porous medium and the velocity of flow around the obstacle in the bore hole also were estimated.

Jan 1, 1996

By V. A. Shea-Albin

Sandstone escarpments surrounding western coal-bearing plateaus serve as critical habitat for animal species. Effects of mining subsidence on escarpment stability are not well documented; therefore, regulatory agencies may limit extraction of coal reserves underlying escarpments. Because millions of tons of this coal exist on Federal Lands, associated public revenues from Federal royalties, and valuable coal reserves, risk being lost. The U. S. Bureau of Mines is using numerical modeling techniques to analyze effects of subsidence on escarpment stability. Finite element models that incorporate bedding plane slip, gob formation, and movement along joints simulate escarpment subsidence observed in the field.

Jan 1, 1994

By Qingwen Shi, Brijes Mishra

The abstract discusses the use of numerical simulations to investigate roof fall in underground mines. It highlights the advantages of the discrete element method (DEM) in simulating large strain problems and fracturing processes, while acknowledging its computational limitations for large-scale problems. The study presents a 3D numerical model coupling the finite difference method (FDM) and DEM to simulate laminated roof failure in a coal mine. The model represents the laminated roof with bonded particles and discontinuities, while the surrounding rock is represented by continuum zones. The research analyzes the fracturing of the laminated roof as the entry advances, demonstrating the coupled method's ability to reproduce laminated roof failure.

Mar 17, 2022

By B. Mishra, Q. Shi

Numerical simulations have been used to investigate roof fall in the past decades. Comparing to the continuum based methods, the discrete element method has been well recognized for its excellent performance in simulating large strain problems and fracturing processes in the rock mass. However, the discrete element method has its limitations. When simulating a large-scale problem, a large number of particles are required, which consumes significant computational resources. In the present study, a 3D numerical model coupled with the finite-difference method (FDM) and the discreteelement method (DEM) was created to simulate the laminated roof failure in an eastern coal mine in the US. In the FDM-DEM coupled model, the laminated roof of the entry is represented by an assembly of bonded particles using PFC3D. The laminated roof is simulated by adding parallel discontinuities. The discontinuities are given certain stiffness and strength in the model. The ribs, floor, and far-field surrounding rock are represented by continuum zones using FLAC3D. The strength of the discontinuities is varied sequentially and the fracturing of the laminated roof was analyzed with respect to entry advance. The results showed that the laminated roof fractures along the discontinuities while an intact roof fractures in a dome shape. Increasing the strength of discontinuity could enlarge the tensile zone inside the laminated roof and hence change the crack distribution. In addition, the crack quantity in the laminated roof behind the advancing face decreases with the increment of discontinuity strength while this trend is not occurring ahead of the advancing face. The simulation demonstrated that coupled method using PFC3D/FLAC3D can reproduce the laminated roof failure in underground coal mines.

Mar 2, 2022

By B. Mishra

This paper presents a rock mechanics investigation of the time-dependent behavior of the rock immediately surrounding the excavation in a hypothetical one-entry coal mine based on the geology of the Illinois coalfields Research in the area of time-dependency is almost nonexistent and, therefore, this research was performed to make inroads into this neglected research area. Numerical analysis of a typical one-entry coal mine in an Illinois basin was performed using the commercial finite difference program FLAC3D. The immediate roof of the coal entry was assumed to be a shale formation. Shale in other formations has shown a tendency to creep with time. Therefore, in this study the authors modeled the shale in the roof using time-dependent characteristics. The input properties were taken from laboratory creep tests performed on shale. Model runs were performed at different stages, mimicking the progressive excavation of the entry. The model results showed that stresses in the roof attained the limit of yielding. Using Mohr-Coulomb failure criteria, potential zones of failure were also predicted. The results showed that the current computational capacities are sufficient to explore this previously uncharted territory of ground control.

Mar 1, 2014

By R. Chen

Most tunnels built in Sydney encounter similar ground situations; they penetrate either the Hawkesbury Sandstone or the shales that lie beneath the city. Tunnels in these materials are generally sup-ported by rock bolts in combination with a shotcrete lining. A method of analysis is presented to improve our understanding of the long term behaviour of fiber reinforced shotcrete (FRS) materials and the tunnel support systems. A finite element method SAFEA (Semi-analytical FE Analysis) is developed to model the combined creep behaviour of a shotcrete lining and the Hawkesbury Sandstone. To model the time-dependent creep behaviour, the bulk modulus and shear modulus of the materials are represented by logarithmic functions in time. A Laplace transform is then applied to these functions of time and the solution of the problem found from a finite element analysis. Tablot?s method is then used to invert the transformed values and find the solution in real time. The time dependent creep deflection of the numerical tunnel models reflects the interaction of the shotcrete lining and rock which have different creep parameters.

Jan 1, 2008

By Gemei Yang, Yihui Zhao

In caved goaf, the friction loss of fluid head is: [h = (R'+ R/Q/ )] Q (for one-dimensional transition flow). The R' and R, which are the functions of two dimensional spaces, are calculated through an empirical formula. Then, the bulking factor and permeability are determined. It is supposed that the airflow in porous media are similar to those in tiny tubes crossing each other. Therefore, the network calculation technique can be used to tackle the field transition flow problem. A lot of case studies showed that the emission of methane in mines mainly depends on the air velocity and has little relation to air pressure. Summing up our experience and experiments, we provide an empirical formula to calculate the gas emission rate per unit area. By means of mass conservation and network calculation, the methane content distribution in steady-state is worked out. Then the dynamic change in airflows and gas content can be analyzed by the characteristic-difference method.

Jan 1, 1987

By Davar Abi-Zadeh, Cillian Brown, Deepak Kandra

"Grout backfill strategy for a particular subsurface concrete tunnel (~4.9km long, 3.5m in diameter, carrying 20” gas pipeline) was based on achieving 1:100 slope of the fill in order to progressively fill the tunnel, in a series of 350m section. Grout rheology, particularly its non-Newtonian and thixotropic behavior, determines the final fill slope for given backfill strategy. The objective of this study was to simulate the two-phase grout mix backfill process using Computational Fluid Dynamics (CFD) and determine the slope of the fill to validate and optimize the backfill strategy. Three dimensional CFD study showed that for a 500m long tunnel section with a single injection point of grout, given its rheology, it will likely keep flowing without filling the 500m section height wise. Design optimization for filling was carried out using two dimensional studies to make the backfill process “slope independent” by incorporating a 2.5m high bulkhead at ~1,000m. INTRODUCTION As part of a gas field development a 20” onshore gas pipeline is required from the landfall site to the processing terminal some 8km inland. At the landfall site the gas pipeline is routed in a ~5km underground tunnel underneath a bay. For operational reasons and planning consents as well as to mitigate environmental impact based on an environmental impact study, once the gas pipeline and the associated services and spares have been installed, the subsurface gas tunnel will be fully grouted. There will be no permanent access to the tunnel after construction is completed and the site compounds have been reinstated once works are complete. One of the key requirements is that “full grouting of the tunnel” is desired. The grouting material used is a non-Newtonian and thixotropic fluid mixture of bentonite, cement, plasticizer, retarder/stabilizer and water. The tunnel is filled progressively in 350m sections using a combination of existing and new pipework assuming the grout rheology will yield a fill slope of 1:100 in a 350m section. The proposed grouting system used one pump at the grouting compound to pump the grout into the tunnel using the existing tunneling pipework. For the longer runs a second booster pump was used in series to pump the grout to its final discharge location. The filling process is controlled via a system of flow meters, pressure transmitters and a tunnel CCTV system."

Jan 1, 2016

By R. L. Howell, L. C. Atkinson

Typical sedimentary sequences overlying coal seams consist of interbedded sandstones, siltstones, shales, and rider coal seams. In many surface coalmine settings, these sediments are saturated; and prior dewatering of them is necessary for effective and economic mining, including the stacking of saturated spoils. Such sedimentary sections usually have a very low vertical hydraulic conductivity that does not allow them to drain in a timely manner prior to their being stripped. One potential solution is installation of drainwells. Drainwells are small diameter wells that can collect water laterally from the various more permeable layers in the overburden and then gravity drain it to a lower layer – often the coal seam being mined – where it can be removed by pumping wells or sumps located in the bottom of the pit. A ground-water flow model utilizing the 3-dimensional finite element code MINEDW has been used to evaluate the effectiveness of usingdrainwells in a hydrogeologic setting that is typical of the Powder River Basin. A series of numerical simulations were completed using various combinations and spacings of drainwells and pumping wells to dewater the overburden and coal seams. The numerical simulations suggest that drainwells can be a very effective method of overburden dewatering.

Jan 1, 2000

By SONGHE WANG, YI XUE, PENG HOU, CAIHUI ZHU, XUANYE JIAO, Feng Gao

Coalbed methane development is an important way to effectively realize a source of clean energy and reduce emissions of carbon dioxide and other gases. However, due to the low permeability of coal seams, the development of coalbed methane in China has encountered substantial barriers. Protective layer mining can efficiently minimize in situ stress and increase coal seam permeability, thus improving gas drainage and avoiding gas disasters. This study analyzed the characteristics of gas migration and the change in permeability during the in situ stress releasing process through experiments and numerical simulation to study the gas drainage effect of a coal mine in an unloaded coal seam under specific geological conditions. First, a stress–strain-seepage coupled test of coal was carried out, and the evolution features of coal permeability during stress loading and unloading processes were investigated. Second, experimental results were used to develop a mathematical model of coal seepage under mining unloading conditions. Finally, a numerical model was developed based on the real geological conditions of the Wulan coal mine to explore the characteristics of in situ stress release and permeability evolution, as well as the gas drainage process in an unloaded coal seam. By combining protective layer mining and gas drainage technology, the risk of gas outburst is significantly reduced.

Oct 1, 2022

By Kyoosang Yoo

The report presents the results corresponding to the analysis of a lining system for tunnels in soil and soft rock in creep-active ground. The purpose of the analysis is to evaluate the performance of a lining at each construction stage. The steps include: 1. Accurate representation of the initial undisturbed state of stress 2. Excavation, 3. Lining installation 4. Injection of mortar and its curing, and 5. Short-, medium- and long-term creep behaviour in the surrounding soil/rock. The response of a prototype tunnel is simulated using the computational finite element framework MSC.marc2008.

Jan 1, 2010

By SONGHE WANG, YI XUE, PENG HOU, CAIHUI ZHU, XUANYE JIAO, Feng Gao

The abstract discusses the challenges of coalbed methane development in China due to low coal seam permeability. It highlights protective layer mining as a method to reduce in-situ stress and enhance permeability for improved gas drainage and disaster prevention. The study involves experimental and numerical simulations to analyze gas migration and permeability changes during stress release. It includes a stress-strain-seepage coupled test on coal, development of a mathematical model for coal seepage under mining unloading, and a numerical model based on the Wulan coal mine to explore in-situ stress release, permeability evolution, and gas drainage in an unloaded coal seam. The aim is to demonstrate the effectiveness of combining protective layer mining and gas drainage technology for gas outburst risk elimination.

Mar 14, 2022

By Yohan Cha, Eun-soo Hong, Gye-Chun Cho

"Rapid population growth and scarcity of space have led many developed cities to bury supply facilities. In line with this, utility tunnels have been employed in Korea since the 1970s. However, approximately 70% of structures were installed more than 20 years ago, in response to the issue of ageing, tunnel enlargement has been proposed. The aim of this study is to investigate geo-mechanical behavior due to tunnel enlargement. Tunnel enlargement methods have been researched to suggest a optimal method. A finite element analysis is conducted to evaluate ground behavior by the expansion of internal space. Vertical displacement and settlement trough width are investigated according to ground stiffness and different enlargement size. It was determined that displacement is affected by the enlargement size and ground stiffness. Based on the deformation results obtained from the numerical analysis, it is possible to predict ground behavior and stability upon tunnel enlargement. INTRODUCTION Various infrastructures such as electric lines, communication lines, gas pipes, and water pipes are jointly accommodated by utility tunnels. These utility tunnels improve the aesthetics of urban areas and help ensure stable supply. The first utility tunnel in Korea was adopted in 1978 and new tunnels are still being installed with the development of new suburb cities. Nevertheless, about 70% of the utility tunnels were installed over 20 years ago and they are still being used through ongoing repair. Moreover, 90% of utility tunnels were installed before 1995. With aging of the nation’s utility tunnels various problems such as concrete deterioration and scarcity of capacity have arisen. As solution, reconstruction has been considered. Reconstruction can enlarge space and improve the performance by replacing existing structures. For reconstruction, two routes have been proposed: underground excavation and cut and cover. In order to avoid traffic problems caused by road occupation and civil appeals during construction projects, underground excavation is the more attractive option. Tunnel enlargement methods have been classified (Seo et al., 2008; An et al 2013) and major considerations during tunnel enlargement have been outlined (Beak et al., 2007). Enlargement construction cases on road tunnels around the world were introduced (Kim et al., 2012) and the deformation curve during tunnel expansion was proposed to investigate the range of protection that should be offered (Kim et al., 2008; Beak et al., 2011). However, tunnel enlargement technology is limited to road tunnels and railway tunnels. Hence, a study on shallow box tunnel enlargement is required for practical application."

Jan 1, 2016

By Keivan PakIman, Maziar Pasdarpour

Transportation tunnels are highly sensitive to ground movements and are required to be stable and secure for safe operation. In urban areas, the interaction between tunnels and adjacent piles, which are widely used to support buildings and other structures, requires careful consideration. The seismic response of tunnels may vary depending on the lateral stiffness and strength of the tunnel walls, while the axial loading and seismic impact of adjacent piles may cause soil displacement and stress changes that can damage the tunnel lining. As a result, tunnel owners often impose strict limits on the design of new piles lying close to existing tunnels including maximum allowable tunnel deformation, stress change limits, and minimum tunnel to pile separation distances. This paper describes a numerical analysis of the inuence of the axial loading and seismic impact of bored pile foundations on subway tunnels, undertaen using the nite element software laxis D. ased on the results of the numerical analysis, the paper suggests a more realistic and less conservative approach for designing piles in close proximity to transportation tunnels. INTRODUCTION The interaction between tunnels and adjacent piles can cause stress changes and displacements in the soil and structures which may adversely impact structural performance and tunnel safety. It is therefore important to take account of relative load transfer and piling conguration when designing new piles in

Jun 23, 2024

By Bo-Hyun Kim, Mark K. Larson

"Bumps remain a critical safety concern in underground coal mining, despite significant advancements in engineering controls. These events occur when relatively high stresses in a coal pillar in conjunction with low confinement exceed the pillar’s critical capacity, causing the pillar to rupture without warning. Floor failure often occurs and can be an indicator of bump risk, as it is strongly associated with brittle failure known as spalling under a lower confinement. Significant floor heave at a western U.S. coal mine has been observed where the pillar width in a three-entry gate road system was 53 m, while no significant floor heave was observed where the pillar width in another gate road system was 22 m. This phenomenon was widely reported in the region and at another mine in another western coal field it has been reported that larger pillars are always associated with floor heave. In this study, a spalling model based on the S-Shaped brittle failure criterion and associated with the anisotropic characteristics of the materials was used in FLAC3D. The observed floor heave phenomenon associated with the larger pillars was demonstrated using this modeling approach.INTRODUCTIONFloor failure in a coal mines often inhibits longwall mining operation, as large displacement of floor strata, known as floor heave, interferes with travel, access, ventilation, and equipment operation. Aggson (USBM 1978) investigated floor heave in West Virginia where underclay is relatively strong and high horizontal stress is present. It was reported that the failure mode is mainly by buckling rather than by plastic flow.This study was developed as part of an effort by the National Institute for Occupational Safety and Health (NIOSH) to better understand rock mass behavior in longwall coal mines in highly stressed, bump-prone ground. More specifically, this study attempts to explain through numerical models small energy releases in the form of floor heave. The authors believe that brittle rock failure is associated with both floor heave and some bump mechanisms, if not directly involved in their cause."

Jan 1, 2019

By Thomas Novak, Sampurna Arya

Controlling dust generation and keeping it below permissible limits to meet federal dust standards at the working face of a room-and-pillar coal mine is a challenge for a mine operator. With the recent changes in federal dust regulations requiring lower worker exposure, maintaining compliance has become increasingly difficult. The current most effective practice of dust control at a continuous miner face in an underground mine is the use of a flooded-bed scrubber. A study carried out by the U.S National Institute for Occupational Safety and Health (NIOSH) indicated that a flooded-bed scrubber could achieve cleaning efficiencies between 58 and 90 percent. But the operation of such a system is maintenance intensive. The flooded-bed scrubber screen becomes clogged with dust particles and requires frequent cleaning to maintain performance. However, the dust control issue is not solely a mining-industry problem. Other industries face similar issues. The University of Kentucky collaborated with Toyota Motor Manufacturing on the development of a novel wet scrubber, called the vortecone scrubber, for capturing over-sprayed paint particles in automotive paint booths. The vortecone scrubber achieved a cleaning efficiency of 99 percent and required minimal maintenance. This study aims to assess the ability of this vortecone scrubber to capture respirable dust in an underground coal mine. The paper presents the results of computational fluid dynamics (CFD) modeling of this vortecone scrubber. It discusses the effects of air quantity and dust particle size on the performance of the scrubber. 

By Thomas Novak, Sampurna Arya

Controlling dust generation and keeping it below permissible limits to meet federal dust standards at the working face of a roomand-pillar coal mine is a challenge for a mine operator. With the recent changes in federal dust regulations requiring lower worker exposure, maintaining compliance has become increasingly difficult. The current most effective practice of dust control at a continuous miner face in an underground mine is the use of a flooded-bed scrubber. A study carried out by the National Institute for Occupational Safety and Health (NIOSH) indicated that a flooded-bed scrubber could achieve cleaning efficiencies between 58 and 90%. But, the operation of such a system is maintenance intensive. The flooded-bed scrubber screen becomes clogged with dust particles and requires frequent cleaning to maintain performance. However, the dust control issue is not solely a mining industry problem. Other industries face similar issues. The University of Kentucky collaborated with Toyota Motor Manufacturing on the development of a novel wet scrubber, called the vortecone scrubber, for capturing oversprayed paint particles in automotive paint booths. The vortecone scrubber achieved a cleaning efficiency of 99% and required minimal maintenance. This study aims to assess the ability of this vortecone scrubber to capture respirable dust in an underground coal mine. The paper presents the results of computational fluid dynamics (CFD) modeling of this vortecone scrubber. It discusses the effects of air quantity and dust particle size on the performance of the scrubber.