Search Documents

By Alfred C. Maevis

On October 27, 1972, ground was broken for the first section of the Second Avenue Subway, a two track underground rail system that was to extend from the south end of Manhattan at Broad Street, north to the Harlem River at 126th Street, a distance of eight miles. This ground breaking was the culmination of 67 years of planning for an east side subway in Manhattan. Following the successful opening of New York City's first subway on October 1904 there was a mass planning for additional subways throughout the City. In 1905 approval was requested of the Board of Estimate for a First Avenue route and Third Avenue route. The Third Avenue route was approved but when action was not taken to start construction, the approval in accordance with the conditions under which it was given was withdrawn. Further reports and plans for an east side subway, usually to be constructed on Third Avenue, were issued in 1920, in 1922, in 1924, etc. Those of us who had worked on the Sixth and Eighth Avenue subways in the thirites and early forties left to join the armed services of World War II in the expectation that we would return and start work on designing and constructing that east side subway. The reason that much of the thrust in those years was to construct on Third Avenue was that there was a Third Avenue "EL" and business interests of the City were in favor of its demolition. This demolition was accomplished in 1955 so one of the incentives to construct on Third Avenue was removed; but an east side subway was always part of the master plan of the City.

Jan 1, 1976

By George J. Karabin

Over the past few years, the use of fully grouted bolts to support the roof of underground openings has increased dramatically. While conventionally anchored bolts effectively reinforce the strata of over 80 percent of mine workings, the use of resin grouted bolts in areas of severe roof conditions has resulted in a substantial reduction in roof falls and an overall improvement in both safety and production. The Roof Control Group of Pittsburgh Technical Support Center, Mining Enforcement and Safety Administration, has conducted numerous field and laboratory investigations to isolate parameters which contribute to the effectiveness of both conventional and resin bolting systems. Specially developed strain-gamed resin bolts, compression pads and differential sag stations installed during the mining cycle have generated data reflecting the loading characteristics and resulting roof stability associated with each type of support. Additional investigations have produced optimum installation parameters of the two systems including the effectiveness of thrust/torque controls for conventional bolts and various bolt/ hole diameter combinations for fully grouted rods. Theoretical analyses, coupled with the actual field and laboratory findings and numerous installation observations have facilitated basic comparisons of the working mechanisms and failure modes of both resin and conventional systems.

Jan 1, 1976

By Robert S. Foote

The U.S. Energy Research and Development Administration (ERDA) is currently conducting a national program to survey for uranium the conterminous United States and Alaska by 1980 using airborne and surface techniques. This paper discusses the techniques used and some of the results of airborne surveys conducted to date by Geodata International, Inc. Airborne gamma radiation and the earth's magnetic field data are measured to provide data leading to regions potentially more favorable for the exploration and discovery of uranium ore. High-sensitivity radiometric and magnetic field data have been gathered from an aircraft with an average surface altitude of 400 feet (Figure 1). Under most conditions, data are usable up to an aircraft surface elevation of about 1250 feet where limitations will be discussed. Results of data analysis under GJO-1632, GJ0-1644, GJO-1654 and GJO-1663 will be discussed.

Jan 1, 1976

By J. A. Bowersmith

The environment in which the surface mining industry operates today is considerably different than that of a few years ago. Increased pressure from the public, government, labor and internal industry factors calling for the fulfillment of rapidly changing expectations is especially intense in the surface coal mining industry. Such things as requirements for increased production, the Mine Health and Safety Act, environmental concerns and land reclamation, shortages of qualified and enthusiastic employees and market cycles coupled with price competition are but some of the specific items that are requiring the surface mining industry to better utilize equipment, materials, and labor resources available, There is one technical tool available which will assist management to increase productivity, improve cost control and assist in planning, organizing and operating surface mines. Industrial Engineering is that tool. Before a discussion of specific applications of Industrial Engineering to surface mining is conducted, it is worthwhile to review a definition of Industrial Engineering and the history of its development. The following definition has been adopted by the American Institute of Industrial Engineers: "Industrial Engineering is concerned with the design, improvement and installation of integrated systems of men, materials and equipment. It draws upon specialized know- ledge and skill in the mathematical, physical and social sciences, together with the principles and methods of engineering analysis and design, to specify, predict and evaluate the results to be obtained from such systems."

Jan 1, 1976

By George H. Tousley

As a member of the vast fraternity of those that supply and service the mining industry, I can assure you that we are amused, amazed, and horrified at the poor drilling and blasting practices of a great number of operations. Yes, ?horrified?. After all, that is our product you are using and abusing. We all know that drilling and blasting is expensive. In some operations D & B costs may exceed excavating or hauling costs, or both. At any rate, it is the only portion of the whole operation that could be said to directly affect other costs. There is no argument that it affects excavating costs. If the overburden and/or product is drilled and hauled, it affects haulage costs. It can easily affect milling costs, if more or less fines is important. And poor fragmentation affects crushing costs. If scalping is done ahead of the primary crusher it can affect production. As has been pointed out, the D & B operation itself is costly, and therefore should lend itself to close scrutiny. Anyone that could immediately decrease haulage costs by 10% would be a hero with any mining company.

Jan 1, 1976

By Haydn H. Murray

This paper presents the results of test work performed with a Pacific Electric Motors (PEM) high intensity magnetic separator (20 kilogauss) , a unit capable of separating weakly, as well as strongly, magnetic minerals in the particle size range of sands to clays. Tests were performed on some 40 industrial minerals. With some minerals excellent separations were attained and with others intermediate and poor separations were accomplished. This study is a preliminary survey and many of the intermediate and poor results can be improved as separation problems are worked out with additional test work. It is demonstrated that with a number of industrial minerals high intensity magnetic separation is a viable beneficiation technique that is economic ally feasible.

Jan 1, 1976

By Sheldon P. Wimpfen

Back in 1970 Congress passed the National Mining and Minerals policy Act, which had as one of its basic tenets to rely on a strong and stable private minerals industry for the development and production of our mineral resources. Since then, a substantial amount of legislation has been introduced that impacts on the minerals industry. Although most of the bills proposed are not passed into law, each bill affecting minerals and mining is given careful review by the Bureau of Mines. Comment is forwarded with the object of being helpful to legislators by providing our assessment of the probable impact of each bill proposed along with suggestions to improve them. Actually few bills introduced become law. For example, in the 93rd Congress 4,260 bills were introduced in the Senate and 17,690 in the House. In the final accounting there were passed 123 private laws and 649 public, 3 percent of the bills introduced. There would be little merit here in attempting to analyze each mineral-related bill that was proposed. Many are similar and aim at making a certain aspect of our minerals activity fit needs. So, to simplify the task the many bills have been grouped by subjects. Slide 1 shows the principal topics and the number of related bills introduced. Putting it altogether, there are 26 principal subjects and almost 200 bills. And these numbers are probably off somewhat, as this accounting was made early in December.

Jan 1, 1976

By Arthur R. MacPherson

Primary autogenous grinding has been in general use for somewhat over 20 years. During this period there have been many highly successful plants built on this principle, while some others have had problems such as: 1. Not performing as predicted from test work. 2. Highly fluctuating tonnage rates. 3. Mechanical problems. 4. High liner wear. Many of the problems with commercial autogenous mills have resulted from improper sampling and testing of the ore during the development period. It is recognized that the fully autogenous mill is very sensitive to any changes in grindability which may occur in the feed to such a mill. The semi-autogenous mill is somewhat less sensitive, but large swings in grindability of the feed require adjustment of ball charge and this cannot be easily accomplished in a short period of time.

Jan 1, 1976

By Ronald F. Ayers

The study upon which this paper is based was completed by Battelle's Columbus Laboratories for the U.S. Army Corps of Engineers in 1974. It is but part of an overall effort by the Corps to evaluate the costs and benefits to the nation of waterway improvements. This study is primarily concerned with future coal markets for production from those counties near the Wabash River in the heart of the Eastern Interior Province. An objective here is to consider a most pessimistic energy (and hence, coal) demand for planning purposes.

Jan 1, 1976

By R. D. Hutchinson

I consider it an honour to be the opening speaker in this afternoon's session on "Canadian Exploration". I also think it most appropriate that this joint meeting of the MMIJ and AIME should consider this subject, because Canada is a major exporter of mineral products and Japan and the United States are our two largest customers. Clearly, therefore, both countries have a valid interest in developments on the Canadian minerals scene. I represent the Mineral Development Sector of the Canadian Department of Energy, Mines and Resources. I will therefore speak from the point of view of the Federal Government. At this point I would like to acknowledge the help and constructive criticism I have received from several of my colleagues in Mineral Development Sector in the preparation of this paper. In any discussion of exploration in Canada, it is essential to emphasize at the outset that Canada has a federal system of government, with powers shared between Ottawa and the provinces. Under our constitution, the federal government has jurisdiction over the north, and over offshore areas, while the provinces own the natural resources within their boundaries. They control the systems of land acquisition for exploration and the terns under which mining titles are issued, and are therefore able to determine the rate and conditions of exploration and development of these resources. It follows that the Federal Government can influence the exploration and development of the provincial resources only indirectly by consultation with provincial authorities. However, once the resources are developed and begin to flow to market, the Federal Government can exert a much stronger influence because of its constitutional right to control both inter-provincial and international trade, as well as through its general fiscal and tax powers.

Jan 1, 1976

By David J. Dunn

Mill liner design is an important factor in grinding. Testing and selection of the optimum liner profile for a given set of mill operating conditions can improve mill capacity, liner life, and liner wear rate At a time when mill avilability is at a premium, production costs are going up, and lead time for mill liner castings is a year or more, the mill liner that grinds best, lasts longest, and costs least is a necessity for economic mill operation. In testing four mill liner profiles for 13' x 12' overflow ball mills, Climax found that an improved design increased mill tonnage by 3 tons per hour while reducing finish grind by 1.7% + 100 mesh, reduced liner wear rate, and almost doubled liner life.

Jan 1, 1976

By William A. Rehrig

During recent years, there have been frequent investigations on the geochemistry of biotite. This work has emphasized, and no doubt was prompted by, factors related to mineral exploration, particularly for those deposits of the porphyry copper type. A large number of papers have been devoted to the obtainment of trace-element data from plutonic biotite. These data have been used to extract primary geochemical information pertaining to the parent magna and the hydro-thermal system which together give rise to porphyry copper deposits. In two early works, Putman and Burnham (1963) and Parry and Nackowski (1963) analyzed base metal contents of ferromagnesium minerals, primarily biotite, from various barrenfmineralized plutons of the Basin and Range Province. One similar conclusion from the two studies was that the Cu, Zn, and Pb contents of magmatic biotite served as indicators of ore development within the granitic rocks genetically related to ore. This theme was then pursued vigorously by a number of authors until the present time. Results, however, have been contradictory, as reviewed by Coope (1974). For example, studies by A1 Hashimi and Brownlow (1970), Lovering et a1 (1970), Putman (1972), and Graybeal (1973) continued to support positive primary relationships between the trace-metal content (usually copper) of biotite and associated sulfide mineralization. By studying biotite in close spatial association will sulfide occurrences, Putman (1972) and Graybeal (1973) developed models for base metal partitioning in magmatic systems based on their discovery of inversely distributed copper between silicate (biotite) and sulfide phases. Conversely, research by Bradshaw (1967) and Blaxland (1971) plus the recent findings of Parry and Jacobs (1975) and Kesler et a1 (1975) found little if any evidence to support a correlation of biotite base-metal or

Jan 1, 1976

By Wayne R. Hopkins

Southern Arizona has one of the world's principal concentrations of copper ore bodies. Twenty miles south of Tucson, close to the Mexican border at Sahuarita in Pima County, is the Twin Buttes mine. In mid-1973, the Anaconda Company and American Metals Climax Incorporated (AMAX) established a 50-50 partnership to operate and expand the Twin Buttes property. Anamax Mining Company was established as the operating company for this joint venture. The production from the Twin Buttes mine is shared between the two partners who market independently. A major expansion of the Twin Buttes operation has included an accelerated stripping programrne for the pit, an expansion of the sulphide concentrator, the construction of an oxide leach plant and a 57 MW diesel generating power station. Part of this major expansion, the large tonnage oxide processing plant was brought on stream in 1975 and is now close to design capacity. The "mine to market gap" has been closed by producing high-purity copper cathodes at the mine site from oxide ore reserves. By using a hydrometallurgical process route, copper production is possible with negligible effects on the environment.

Jan 1, 1976

By Albert J. Shohet

The increasing scarcity of bentonite coupled with the potential of improved pellet strength have created a need for understanding the effects of thorough bentonite dispersion in taconite concentrate. It has been known for more than a decade that under certain conditions substantial savings of bentonite are realizable by using thorough mixing of bentonite as compared to poor mixing. Extensive work done by J. O. Zetterstrom l at the Univer¬sity of Minnesota indicated the effect of thorough bentonite mixing in a controlled laboratory testing. Commercial hardware was not available at the time Zetterstrom1 paper was published and not much work was done until R. L. Stone, J. M. Karpinsky2, did work with Muller mixing. Nabush 3 worked with the pugmill principle, and Hoogovens 4 and Robe River 5 used the fluidized bed principle. It was very hard to convince iron ore industries to improve the mixing of Bentonite and taconite for the following reasons: A. The initial capital investment for improved mixing equipment; B. The relatively low bentonite cost a few years back, which was not enough to justify new equip¬ment investment;

Jan 1, 1976

By J. C. Irvine

Meramec Mining Company is a joint venture by Bethlehem Steel Corp. and St. Joe Minerals Corp. which mines and pelletizes iron ore at the Pea Ridge Mine. The Pea Ridge property is located near Sullivan, Missouri, about 70 miles southwest of St. Louis. The orebody was delineated in the mid-1950's by St. Joe during a lead exploration program. The first test holes drilled on the Pea Ridge magnetic anomaly revealed the presence of a large magnetite deposit; further drilling in 1956 and 1957 confirmed that the orebody was mineable, Meramec Mining Co. was incorporated in 1957 and shaft sinking began late in the year. Production commenced in April 1964. The orebody is overlain by about 1300 feet of flat-bedded sediments. It is tabular, about 2600 feet long and up to 600 feet thick. It dips about 80° and is of unknown depth. The ore is mainly high grade magnetite with small zones of specular hematite. The wall rock is a Precambrian rhyolite porphyry. The mine was initially started with five major levels on 150 foot intervals. Crosscuts were driven across the orebody on 190 foot centers. Banks of scopes were mined between the crosscuts by a modified shrinkage stoping method. This was done by undercutting a 40 foot wide by 150 foot long block and blasting horizontal "lifts" drilled on 5 foot intervals. A 65 foot still was left between levels which contained the slushing drift, fingers, crown pillar, and adequate thickness for support. By 1971 a ?lattice? of pillars had been left and mining had progressed to the point that an orderly pillar recovery program was necessary.

Jan 1, 1976

By R. E. Mason

Shotcrete has been used for approximately 20 years to facilitate tunnel excavation through poor ground. Early examples of such usage in North America include the recuperation of the Granduc Mines access tunnel in Northern British Columbia, and similar work performed in the Carley V. Porter and Big Walker Tunnels in the United States. Mining companies such as Craigmont Mines in B.C. and Hecla Mines have used shotcrete in their workings for the past ten years. Shotcrete is now a widely utilized fool in the mining and tunnel construction industries in North America, but the accumulated experience is too limited for many to fully appreciate the capability of shotcrete to control ground movements and to understand the limitations of this tool. It is common, for instance, to use shotcrete to "bridge the gap" between rock bolt-supported and steel-rib supported ground and to avoid the use of shotcrete in water-bearing ground. Shotcrete can, and has been, used economically and practically under most severe ground conditions.

Jan 1, 1976

By Geoffrey G. Hunkin

This is a brief state of the art paper describing current (1975) Uranium recovery plant flowsheets, some notes on system selection, design philosophies, and materials of construction. The in-situ, or borehole solution mining, of Uranium is a process which has been developed over recent years to better match Uranium mining and milling technology with the size, shape, grade and territorial distribution of the remaining identified Uranium deposits of western United States. Solution mining recovery plants are pure hydrometallurgical units ideally suited to automation, modular design, and mobility. Similar to conventional Uranium mills, two basic flowsheets, one acid and one carbonate, are in use, but the predominance is reversed so that the majority of plants employ the alkaline carbonate flowsheet, All plants incorporate resin bead ion exchange Uranium recovery for both acid and alkaline circuits.

Jan 1, 1976

By Miles L. Silberman

Three major suites of igneous rocks were erupted in the Great Basin in middle and late Cenozoic time. The first, most likely, resulted from sub- duction of a Pacific plate (Farallon plate) beneath the North American plate, resulting in eruption of andesitic rocks in the northern Great Basin between 42 and 43 m.y. ago. Between 34 and 17 m.y. ago, igneous activity migrated to the southwest, largely as eruption of volumincus rhyolite-quartz latite ash-flow sheets, ending about 17 a.y. ago with the onset of crustal extension and north-south-trending Basin and Range (rift) faulting. The second volcanic suite erupted between 17 and 8 m.y. ago in the northern Great Basin; is mostly basaltic or bimodal basalt-rhyolite. The third volcanic suite consists of andesitic and rhyolitic lavas and some basalt erupted between about 22 to 6 m.y. ago in the western Great Basin along the northwest-trending Walker Lane fault zone. Hydrothermal ore deposits are associated with all suites of igneous rocks, but the largest production has come from mines associated with andesitic rocks of the third (western Great Basin) suite. The oldest (34 to 42 m.y.) andesitic rocks (first suite) of the northern Great Basin have produced some large deposits; slightly younger silicic rocks of this suite are mostly barren. Many small ore deposits are associated with the 17- to 8-m.y.-old basalts (second suite) of northern Nevada.

Jan 1, 1976

By Robert H. Hooff

The Vor-Siv Dewatering and Classifying Unit was developed by the Polish Coal Industry because of a need for a unit that would dewater and classify high volumes of solids in water slurry. To be practical, the unit needed to be relatively small in size, simple in design, involve low operating costs, and be able to give a dewatered product of less than 30% moisture. The answer to the above mentioned criteria was the Vortex Dewatering Sieve or, as we refer to it, the Vor-Siv. The original installation of the unit, as we know it today, began in 1963 when the Pols installed the unit in a full scale pilot application. By 1966, at least 30 of these units were installed throughout the Polish Coal Industry. This equipment was originally introduced in the United States in 1966 at the Fifth International Coal Preparation Meeting in Pittsburgh, Pennsylvania. The first installation in the United States was not achieved until 1970, when Mr. Fred Sachs of The Valley Camp Coal Company, Triadelphia, West Virginia, installed a Vor-Siv in a retrofit application. To date, there are 36 Vor-Sivs installed in this country and 29 in the process of being installed or delivered.

Jan 1, 1976

By J. R. Hunter

The present is rooted in the past. This is particularly true in the case of mining operations. Coal mining in the United Kingdom is considered an old Industry comprising today 246 Coal Mines many of which have worked coal reserves in their locality for over 100 years. More than half the current producing mines lie in the Yorkshire and Midlands coalfields. They are in the oldest age group and produce 70% of the Industry's output. Some 50% of the remaining U.K. workable reserves amounting to approximately 98,000 million tons are still available to these regions. Fig. 1 Over the past two decades a gradual erosion of demand for coal in the U.K. has virtually halved the Industry's capacity. The number of Mines has reduced by 53% during the past 10 years. Productivity has increased by some 42% mainly through improvements in the central coalfields which has enabled costs to remain broadly competitive with oil.

Jan 1, 1976