Search Documents

By M. Boucraut

After stating the advantages of the magnetic roasting technique as applied to iron ores, the authors report on technological research by I R S I D * in the field of magnetic roasting in fluid-bed furnaces This investigation was conducted first on an experimental two stage fluid-bed furnace which processed permanently 100-200 kg/h of ore, then on a three stage fluid-bed furnace with 1-2 t/h working capacity and at last on a 250 t/day pilot furnace The specific features of the IRSID process comprise - on the one hand, using special burners in the roasting reactor thereby ensuring a high production rate of the furnace - on the other hand, using a heat-exchanger where the preheating and cooling stages of fluidized ore are associated, so as to allow an efficient and simple cooling of both roasted ore and waste gases flowing out of the roasting reactor, thereby supplying heat to the crude ore and combustion air for the reactor burners Starting in 1965 the operation of the 250 t/day pilot plant at the Bazailles mine gave IRSID the opportunity of improving the conveying appliances and adapting them to the process, while perfectly confirming the metallurgical results obtained under ideal laboratory conditions

Jan 1, 1968

By B. G. Hicks

The Manapouri Power Project is located in New Zealand's South Island Fiordland. The project is being constructed for the New Zealand Ministry of Works. Construction began in 1963 and is scheduled' for completion in 1969. The project will divert water from the natural, glacially carved Lake Manapouri, at Elevation 580, through vertical- penstocks into an underground powerhouse 364 feet long, 127 feet high, and 59 feet wide excavated about 700 feet below ground surface and about 560 feet below the present lake level. The possible ultimate power installation will produce 700 megawatts from turbines located in the underground machine hall. The turbine flow will discharge through the 6-mile, 30-foot diameter tailrace tunnel into a fiord arm of the Tasman Sea. The rocks in the project area are primarily Paleozoic Fiordland Complex gneiss, schist, amphibolite, and marble intruded by granitic rocks and pegmatite. Shear zones have been encountered in the tunnels and machine hall. These produce water and occasionally require steel support. The machine hall arch was stabilized entirely by rock bolt reinforcement. Rock mechanics instrumentation has been used throughout the project both for pre-construction design calculations and to monitor tunnel rock loads and movements of the machine hall roof and walls. About 28 miles of the 100-mile transmission line will be constructed across glacially oversteepened slopes and debris or swamp filled valleys between the power plant and the eastern edge of the mountainous area. Steep glacially carved rock slopes and locally unstable glacial till complicated construction of the transmission line access roads.

Jan 1, 1968

By George L. Wilhelm

Many factors, some of which are not easily defined or described, must be considered in the design of a hydraulic backfill system. After participating in the design of several plants, I have a conviction that future refinements in sandfill systems must come in large part, from the merging of good design ideas and information from existing operating plants. It is important then, that we document and publish information on existing plant designs and their operating characteristics. This information will then be available for use by our successors and later innovators in hydraulic fill placement. The Mayflower hydraulic sandfill system is similar to other plants. The intent of this paper is to describe only this system's unique design and operating characteristics. I will not describe in any detail, the familiar elements of the system. I will document some of the observed hydraulic characteristics of the system, elaborate on some of the design situations that had to be solved, and will discuss operating factors that are not generally described in our technical literature.

Jan 1, 1968

By E. F. Young

An integrated steel company is an industrial complex ranging from raw materials mining, through pyrometallurgical smelting and refining, and hot shaping, to product finishing and coating. Within this complex is a great variety of operations which use vast quantities of water, and a variety of water uses which can result in pollution of many different types. The industry has recognized most of its problems for some time, and has spent a great deal of money and effort in reducing and eliminating pollution. A recent survey by AISI showed that the industry has spent, within the last 15 years, two hundred forty millions of dollars on water pollution control, and has authorized spending eighty-seven millions more on this type of non¬productive facilities. While much still remains to be done, I think the record to date is one we can be proud of. In this presentation, we will attempt to outline a number of the water pollution problems encountered in an integrated steel company and to show what types of corrective action have been and are being taken, using Jones & Laughlin Steel Corporation as an example.

Jan 1, 1968

By R. D. Herron

Mining coal under deep cover conditions is certainly the proper phrase to use in describing one of our newest operations. Located in the southwest corner of Virginia is this operation which is the Beatrice Mine of the Beatrice Pocahontas Company, a joint venture of Republic Steel Corporation and Island Creek Coal Company. The mine is working in the No. 3 Pocahontas seam in an assigned area of over 9500 acres containing over 60 million tons of recoverable, high quality, low volatile coal. The site of the mine opening was at Keen Mountain, Virginia, where the seam lay 1350 feet below the surface. This depth, greater than anything attempted thus far in the coal industry on this continent, would pose some problems, we felt, with which we had not previously had to contend.

Jan 1, 1968

By B. Fagerberg

Crushing and grinding practice in Sweden follows largely the international pattern. Certain special circumstances, however, have had an influence on the development. Most mines are worked underground in either quite small or in very large units. To utilize small sulphide ores, custom milling is rather common. Apart from the cement industry, the rock species treated are hard and abrasive. Another important factor is the increasingly strict requirements placed on the mechanical condition of different products, especially lump ores and coarse iron ore concentrates. A significant feature in the design and development of Swedish crushing and grinding practice has also been close cooperation between machinery manufacturers and the users. An account of these conditions and an outline of the crushing and grinding techniques employed in Sweden are presented in this paper with emphasis on the mining industry. For background purposes it may be mentioned that crude ore production in Sweden last year included 45 mill. tonsx) of iron ore, of which some 20 mill. tons from Kiruna alone, and 4 mill. tons of sulphide ore from 22 other mines, fig. 1. In addition 8 mill. tons of limestone were quarried for cement production and several million tons of stone and sand for roads, aerated concrete, etc.

Jan 1, 1968

By W. F. McDermott

The transportation of solids by pipeline is not new. In 1891 a United States patent broadly covering a method of pumping coal with water was granted to W. C. Andrews. His pilot plant was constructed on what is now the site of the New York Public Library in Manhattan. His process was applied to pumping coal mine waste back into the worked out portion of coal mines. On October 26, 1967, the world's first long distance iron ore slurry line was put into service by Savage River Mines. The commissioning of this 5.0 million dollar installation climaxed three years of development, testing, and construction and proved the Company's faith in pioneering this unique transportation method for iron ore. This paper will discuss some of the more pertinent items in connection with that three- year period. Also to be discussed will be the operation of this line during the past eleven months.

Jan 1, 1968

By Roscoe W. Stensrud

The Marcona Corporation was established in 1965 to consolidate the ownership and management of the Marcona group operations. This company, with headquarters in San Francisco, has the following principal operating subsidiaries: Marcona Mining Company, formed in 1953, conducts iron ore mining, beneficiation and pelletizing operations in Peru. Cia. San Juan S.A., Panama, which contracts for sale and delivery of iron ore from the Marcona operation in Peru and from Mount Goldsworthy in Western Australia. Sari Juan Carriers, Ltd., a subsidiary of Cia. San Juan which owns and charters vessels for the bulk ocean transportation of iron ore, petroleum products, coking coal, slurry, salt and other commodities.

Jan 1, 1968

The Putnam Coal Mine, at design capacity, will be the third largest underground bituminous coal mine in the world and will feature the world's longest single flight belt conveyor. Construction is now in process; initial mining will commence in early 1969 and design capacity will be reached in 1971. I'm Jerry Workman, Assistant Mining Manager for the Coal Group of the Mining and Metals Division of Union Carbide Corporation, and I am acting as Project Manager for installation and start-up of the Putnam Mine. The Putnam Coal Mine reserves are located in south-central West Virginia and contain approximately 27,000 acres of prime Pittsburgh No. 8 coal; reserves are sufficient to support a 3.5 MM tons per year operation for over 30 years. The mine portal area is located some six miles inland from the Kanawha River. The river loading facility is located approximately 156 miles by way of river from the market.

Jan 1, 1968

By Wilbur H. Smith

Geologic mapping techniques at the Bingham Mine have evolved as rapidly expanding applications of geological data have caused new methods to be utilized. The most significant changes in method have been in the preparation of the base map and in computer application of collected data. Formerly maps were prepared by surveying with transit or plane table. Currently a photogrammetric map, on the scale of 1-inch equals 200-feet, is prepared semi-annually and continuously updated to keep pace with the removal of more than 350,000 tons of material daily. Larger scale bases for specific problems, such as areas having unstable slopes, are prepared by use of aerial and terrestial photography and photo mosaics. Note sheets designed for computer application enable fast processing of the data. Application of geology at the Bingham Mine has been increasing rapidly in recent years. The effect of structure, rock type, and alteration on slope stability, the relationship of sulfide mineral distribution to concentrating results, the effect of rock and mineral types on waste dump leaching, and requirements of a reliable internal source of silica flux for smelting are a few of the problems which require the collection and application of geologic data.

Jan 1, 1968

By Virgil W. Carmichael

In the Fort Union formation of western North Dakota, eastern Montana and northeastern Wyoming there are immense tonnages of lignite and subbituminous coal that have not yet been evaluated in terms of present economic conditions. Continued expansion of United States energy requirements has focused ever increasing attention on this tremendous resource, particularly as efficiency in mining and transporting of coal, as well as in electrical energy generation and transmission have improved and as hydrogenation and gasification of coal approach economic feasibility. This "total energy" concept for coal includes all of the energy uses that coal offers and has resulted in mergers of oil and coal companies and acquisition of coal re- serves by oil companies, as well as by coal companies and others. There is no doubt that these coals are entering an exciting new era of exploration and development that will result in greatly increased production. As a matter of fact, increased consumption for energy generation is well under way and recognition of the economic feasibility of high-Btu pipeline gas and synthetic petroleum products from coal is imminent. As coal is gradually displaced in steam electric generation by the more exotic fuels and processes, it will be increasingly used as raw material for the synthetic petro-chemical industry and the organic chemical industry.

Jan 1, 1968

By James K. Ballard

Leach dumps in Butte are relatively new in comparison with older established dumps in other areas throughout the West. With the exception of one 10 million ton dump, all dumps have been formed on a prepared base. This is necessary because the entire leach dump area overlies an alluvial fill which varies in depth from 100 to 400 feet and through which solution would be lost. Preparation of the leach pad consists of first removing all vegetative material and compacting the exposed surface with rollers. This surface is covered with a 4" layer of minus 1" crushed rock which in turn is roller compacted. A 3" compacted layer of asphalt hot mix is then applied to the crushed rock surface. Final sealing is effected by a 1/4'? coating of catalytically applied hot asphalt. Dump leaching was inaugurated in 1964. First solution applied was wholly made up of mine water pumped to surface through a central pump shaft. Sulfuric acid was added on surface at a surge pond to control pH of the leach solution. Acid addition is necessary not only to benefit the leach dumps, but to prevent the formation of ocher scale within the pipe line distribution system. Mine water pH is on the order of 2.8. The combination of ferrous and ferric iron as well as magnesium and aluminum salts is such that ocher forms at a pH of 2.38. It is therefore mandatory to control pH at 2.0. Dump effluent pH is held at 2.3 or less.

Jan 1, 1968

By A. Z. Dimitroff

Immediate detection of methane buildup or of sudden liberation of large quantities of methane in the face area is essential to avert disasters in coal mines. Proper timely detection and handling of methane have always presented problems in extremely gassy mines, and these problems have been magnified by present accelerated mining methods. Strict rules and regulations have been established by coal-mining companies, States, and the Federal Government, which provide for periodic inspections for methane in face areas when electrical equipment is working. Other provisions require the operator' to shut down electrical face equipment and change or adjust ventilation when more than 1.0 percent of methane is detected. Nevertheless, human failure to detect such conditions has been responsible for numerous ignitions arid explosions Recognizing this fact, Marling J. Ankeny, former Director of the Bureau of Mines, proposed in 1958 the development of an automatic methane-monitoring device. He envisioned such a device as being entirely dependable, capable of giving a warning when a predetermined concentration of methane in air is reached, and capable of deenergizing the equipment and rendering it inoperative when a dangerous concentration of methane is present in the air. Such a device has been developed by the Bureau of Mines Health and Safety Research and Testing Center in Pittsburgh, Pa.

Jan 1, 1967

By George A. Komadina

Pima Mining Company has recently completed their expansion tripling the plant capacity to 18,000 tons per day and now is in the process off expanding to 30,000 tons per day with completion scheduled for the summer of 1967. This paper briefly discusses the additions to the mining department and support areas with a more detailed report on the complete new crushing plant and additions to the concentrator. The crushing plant includes a 54-inch gyratory crusher, three 7-foot standard and seven 7-foot short head crushers along with necessary screens, feeders, and conveyor belts to produce a minus 1/2-inch rod mill feed. The concentrator consists of ten milling sections, each containing one 10-foot by 16-foot rod and two 10.5-foot by 13-foot ball mills, classification is done with cyclones. Pulp from each section is floated in 50 cells of 66-inch Fagergren flotation machines to produce a rougher concentrate which is cleaned in six stages of Denver cleaners to produce a final concentrate The various mill products are thickened with disposal made in conventional manner. Plant instrumentation is discussed in the paper.

Jan 1, 1967

By Peter Joralemon

I want to limit my remarks to epigenetic ore deposits, but do not necessarily subscribe to the classic theories of hydrothermal ore deposition. I will consider an epigenetic deposit as a primary deposit in which the economic minerals have been introduced subsequent to the formation of the enclosing rock, regardless of the source. Past ore discoveries have been made to a great extent by prospecting techniques that have remained relatively constant over the last many decades. In many cases the discoveries have been enlarged or enhanced with the use of technical tools such as geophysics, but theoretical geology, which should serve as a foundation for exploration, has shown little progress of practical importance since the turn of the century.

Jan 1, 1967

By Doug Brown

The recent expansion of our cities into hilly areas, particularly on the Pacific Coast, has resulted in damage or destruction of many homes due to geological problems such as landslides, soil creep, erosion, subsidence, or groundwater seepage. In southern California, landslides are the principal cause of damage and attention is focused on them. Landslides have occurred due to the reactivation of old slide masses, or have been caused by grading and increased water, infiltration resulting from development.. Reactivation of a portion of the ancient Portuguese Bend landslide in Palos Verdes, Los Angeles County, affected approximately 150 homes. A common type of new failure' occurs when grading has undercut bedding or other essentially planar surfaces so that they dip unsupported out of slope. Other slides have occurred due to the inherent weakness of the material involved. Preventive measures undertaken to eliminate damage in the southern California area have. included areal geologic mapping programs-in-advance of development, enacting or strengthening grading codes, and requiring extensive studies by consulting geologists and soils engineers both during the design stage and during construction. In the design stage, proposed cuts are frequently flattened, lowered or reorientated. Frequently, due to the high cost of land, they are supported by compacted fill buttresses. As a result of these measures, the geologic environment has a major effect on the feasibility, design, and development of, a very substantial percentage of tracts or individual homes.

Jan 1, 1967

By August E. Vandale

I speak to you today on the subject assigned to me, "Subsidence - a Real or Imaginary Problem", as a representative of Consolidation Coal Company (a wholly owned subsidiary of Continental Oil Company). The information I relate to you is our experience in the Pittsburgh Coal Company Division of Consol and covers the Pennsylvania properties and mines with particular emphasis on the mines in the south- western portion of the State or in the immediate vicinity of Pittsburgh, Pa. Mining of Freeport and Pittsburgh seams of coal in the Pittsburgh vicinity dates back over one hundred years. Consol, or its predecessor, Pittsburgh Coal Company, has been actively engaged in mining in the area since Pittsburgh Coal Company was organized in 1900. Pittsburgh, Pennsylvania came into prominence as the Steel City largely because of the vast reserves of high grade metallurgical coal readily available in the immediate vicinity and also because of its favorable river transportation. Early in the 1900's we operated over 100 small coal mines, with operations located in the Counties of Allegheny, Fayette, Washington, Westmoreland. We have also operated mines in Somerset and Greene Counties. Titles in Pennsylvania can be in three estates: (1) title in fee, (2) title to the mineral, (3) mining rights permitting the removal and extraction of the mineral with or without waiver of surface damage. Consol has over the years acquired good legal title to the coal lands purchased from individual farm owners, with good broad mining rights, and in 98% or more of its title has a complete waiver of surface damage or the right to subside the surface land. In the early days of our Company, individual coal farms were purchased from land owners. Many of these titles severed the coal estate from the in fee title and good mining rights with waiver of surface were conveyed in the original severance deed. Thus, minable coal reserves were put together by the purchase of the coal under many individual farms in an area. In the early years, the mines practiced hand dug mining - later going to mechanical cutting with hand loading of the coal. Systems used were entry driving with room and rib panels. We have practiced full recovery mining as far as practical during the years of hand loading, as well as in the later years when the mines were mechanized. Mining system layouts, methods and procedures have changed from time to time to keep pace with improved mining machinery and new inovations, such as roof bolting and rubber tired haulage.

Jan 1, 1967

By F. L. Kadey

A discussion of fillers would not be complete without allotting adequate time to that unique and different mineral material, diatomaceous silica. Historical references to its use challenge the aesthetic aspect of man's curiosity; whereas modern scientific tools have provided a dimension of measurement that has motivated many of its more recent applications. A brief review of what is already known is in order. The diatom is a unicellular, plant-like, microscopic organism, related to the algae1. Its natural function appears to be that of a food for other marine or lacustrine organisms, The diatom's "claim to fame" from an industrial viewpoint is dependent on the fact that it secretes an opaline siliceous skeleton that must survive, chemically and structurally, the geologic processes that caused its formation in the first place; its subsequent demise, burial, consolidation, and alteration; and finally, its ultimate exploitation by man--in somewhat that order. In addition to its siliceous nature, the skeletal structure of the diatom possesses a variety of shapes, patterns, and sizes that have not only been the intrigue of microscopists for decades, but have served to set diatomite apart as an industrial mineral; and have reserved for it applications that cannot be satisfied by any other material. Its chemical inertness, its intricate structure, and its intrinsic hardness-coupled with fineness and friability-- are generally known and have accounted for its application in a wide range of filtration and filler uses. The increasing use of the electron microscope has considerably expanded our knowledge of heretofore unseen secondary and tertiary structure of submicron dimension in the diatom valve. The development of electro-sensing methods of particle size measurement which seem to supersede sedimentation and microscopic techniques has portrayed size distribution in a more realistic light. Interest in the surface chemistry of these silica structures has further strengthened our understanding for certain uses. Thus, new tools and ideas have made possible the introduction of diatomite into such sophisticated technologies as that of chromatographic supports, its improved utility in paint applications for the control of gloss and sheen, and its usefulness in the entirely new concept of "Dry Acid Concentrates." Each of these applications has been discussed elsewhere before people particularly interested in analytical chemistry, in paint, and in liquid handling, respectively, where the diatom has been a means to an end. The emphasis here, before the mining fraternity, however is on diatomite as a raw material with reference to the uses mentioned above. It is therefore toward an awareness and understanding of diatomite properties pertinent to these newer filler applications that this paper is directed.

Jan 1, 1967

By Harry Elkin

Control of coal dust has long been an important aspect in the conventional mining of coal; the main reasons being from a health and disaster standpoint. With the advent, of mechanized longwall mining, the control of dust has required more attention due to the high extraction rate common to most longwall systems. The purpose of this paper will be to describe the dust abatement activities of the longwall operation at Sunnyside. Kaiser-Steel Corporation has three mires located at Sunnyside, Utah, with a total production averaging 6,800 tons of clean coal per day. Of this 6,800 tons, 71 % is mined with continuous miners, the remaining 29% coming from one longwall unit located in No. 3 Mine. Our first longwall panel was started in November, 1961. In October, 1966, we started mining our seventh panel. The present panel is located in the Upper Sunnyside Seam which averages five feet in thickness, but does get as low as 51 inches. The seam pitches 5.5% in this vicinity. The roof is generally good and is comprised of 10 inches of shale cap rocs overlain with sandy shale and sandstone. The floor is sandy shale and is quite undulating in nature. The present panel is 3,800 feet in length with a face of 670 feet. The major equipment employed on our longwall unit is a 125 H.F. Anderton Shearer-Loader, British Jeffrey Diamond armored conveyors and a Dowty self-advancing-roof support system. The Anderton Shearer in use on our longwall unit has a 60" diameter x 27" cutting drum. During the shearing cycle, it traverses the face at 20 feet per minute with a cutting rate of 7.5 tons/minute.

Jan 1, 1967

By Ronald L. Haxby

This report presents a refractive seismic technique for evaluating the strength of rock within an open pit bench. A concept of correlating rock strength and seismic velocity is discussed and a method of predicting the degree of fragmentation of a pit bench is introduced, Figure 1 shows the area of interests [ ] Most of the work was performed while completing graduate studies at the University of Arizona.

Jan 1, 1967