Search Documents

By T. F. Torries

The primary criteria used by the mining industry to judge the merit of a project is internal rate of return (IRR) rather than net present value (NPV), although NPV is favored by academicians. This paper discusses the problems of IRR and NPV and compares the multigoal nature of the decision¬makers and their need for informa¬tion having the characteristics of NPV and IRR. The conclusions reached are that both NPV and IRR can be used for investment ranking, that NPV suffers the same multiple root problem as does IRR, and the use of conventional incremental IRR to reach NPV¬consistent project ranking is mis¬leading.

Jan 1, 1999

By F. G. Rinker

The world demand for metallized iron continues to increase, keeping pace with steelmaking requirements for lower cost hot metal. Virgin iron ore and in-plant oxide fines can be reduced to direct reduced iron (DRI) and hot briquetted iron (RBI). MR&E has developed an improved coal-based process for cost-effective production of either DRI or HBI. Starting with dry compaction, the process combines the latest technology for material preparation, rotary hearth furnace construction and environmental control. Coarse iron ore fines are blended with pulverized non-metallurgical coal to produce a highly metallized (>90%) product. This paper presents production and installation cost data based on operating and under-construction iron oxide reduction facilities.

Jan 1, 1999

By D. H. Carlson, J. H. Johnson, C. F. Renders

Introduction Diesel-powered vehicles are used extensively in underground mines throughout North America. The bulk of the diesel vehicles found in underground mining operations are used for loading and ore haulage, as well as for transportation of personnel and supplies. Along with the advantages of using diesels underground is the disadvantage associated with diesel-tailpipe particulate-matter emissions (DPM). The concentration of DPM in the ambient air of US underground metal mines is not now regulated by the Federal Mine Safety and Health Administration (MSHA). However, recent studies have shown DPM to be mutagenic (National Institute of Occupational Safety and Health, 1988), and the American Conference of Governmental Industrial Hygienists (ACGIH) has recommended that the exposures of per¬sonnel to DPM be limited to an 8-hr time-weighted average concentration (threshold limit value or TLV) of 0.15 mg/m3 (Anon., 1995). The authors, while making measurements in a number of US underground mines that use diesel haulage equipment, found mine air DPM concentrations ranging from 0.2 to 2.36 Mg/M3 (McCawley and Cocalis, 1986; Watts et al., 1989; Cantrell et al., 1991; Haney, 1992; US Bureau of Mines, 1992; Watts, 1992; Watts et al., 1995). If the proposed DPM TLV were to be adopted as a permissible exposure limit (PEL) for US underground mines, the proposed limit of 0.15 mg/m3 PEL would be lower than any of the concentrations measured in the earlier studies and would represent more than a 15-fold reduction from the maximum 2.36 mg/m3 concentration. A 0.15 mg/m3 PEL would also represent a 4.5-fold reduction from the average 0.68 mg/m3 measured mine ambient air DPM concentration reported in this paper. Other diesel tailpipe emissions that are now regulated underground include carbon monoxide (CO), with a PEL of 50 ppm; nitrogen dioxide (NO,), with a PEL of 5 ppm; nitric oxide (NO), with a PEL of 25 ppm; and sulfur dioxide (SO,) with a PEL of 5 ppm. Because the concentrations of these gaseous pollutants and DPM are affected by the state-of-maintenance (Waytulonis,1992), it is important that a means be developed to measure emissions from engines that are now in service to determine when maintenance is needed. The current study was the result of an inquiry by mine¬maintenance personnel who had been receiving complaints about high concentrations of diesel soot (DPM) in mine headings from load-haul-dump (LHD) vehicle operators. Mine-maintenance personnel were searching for an objective test to determine if the diesel tailpipe particulate emitted was excessive. The mine was also evaluating electronically controlled, two-cycle, naturally aspirated, direct-injection diesel engines on some of their JCI (John-Clark Inc.) load-haul-dump (LHD) vehicles. These LHD vehicles were used to haul freshly blasted ore from mine headings to a feeder breaker. The feeder breaker breaks down the larger chunks and feeds the broken ore onto a conveyor. Michigan Technological University, in past studies, developed an emissions-measurement apparatus (EMA) ca¬pable of measuring diesel vehicle tailpipe pollutant concentrations (Chan et al., 1992; Chan et al., 1993; Carlson et al., 1994). At the time of the study reported here, most of the mine's LHD vehicles used a 12-cylinder, four-cycle, naturally aspirated prechamber diesel engine. The study was undertaken in cooperation with mine maintenance supervisors from late 1992 through July 1993. The objectives were to compare diesel exhaust emissions between the 6-cylinder, two-cycle, electronically controlled, direct-injected diesel engine and the 12-cylinder, four-cycle, prechamber diesel engine and to, then, use the data collected, in conjunction with mine ambient air measurements, to demonstrate the application of the "deterioration factor" (Chan et al., 1992), which is a measure of the state-of-maintenance of mine-vehicle engines that are now in service. The information would be used to identify vehicles that need maintenance to reduce emissions. The data reported here are unique in the sense that they combine underground diesel vehicle ambient and tailpipe

Jan 1, 1999

By H. H. Murray

Recently developed clay deposits that will impact regional and world markets are described. These deposits, their location, geology, and physical properties are delineated. Kaolins from the State of Para in Brazil and from Ukraine; bentonites from Argentina and India; and palygorskite and sepiolite from China are world class deposits that when processed using modem technology will produce excellent products. Other deposits that may affect regional markets are kaolins from China, Australia and Indonesia; bentonites from Georgia (formerly USSR) and China; and palygorskite from India and Ukraine. New ball clay deposits that will affect regional markets are in China and Indonesia.

Jan 1, 1999

Traditional finance theory recommends discounted cash flow (DCF) analysis as the tool to value mineral properties. Yet, the calculated values by this method are usually lower than the market value. Finance theory also advises us to develop an undeveloped project immediately if its net present value is positive. Most projects are, however, only developed when the economics are highly favorable. This paper uses insights from option-pricing theory to explain these divergences between market behavior and finance theory and presents simple modifications to discounted cash flow analyses that will lead them to produce correct valuation and development timing advice.

Jan 1, 1999

By D. Potter

In 1990, Freeport Exploration began regional reconnaissance exploration programs in Irian Jaya, the easternmost province of the republic of Indonesia (Fig. 1). Irian Jaya occupies the western half of the island of New Guinea. Freeport was awarded an initial contract of work that totaled 2.6 million hm2 (6.4 million acres). The company was subsequently awarded additional concessions that added 1 million hm2 (2.5 million acres). The concessions require work commitments and periodic relinquishments. Due to these relinquishments, Freeport’s current land position totals 1.9 million hm2 (4.7 million acres). Freeport began the exploration program to locate additional Grasberg deposits, the largest deposit in the Ertsberg district. But the company recognized that other types of deposits could be present in the largely unexplored area of Irian Jaya.

Jan 1, 1999

By D. A. Day, H. L. Marsh, P. J. Stephens, C. A. Wiggins

Lightweight cellular grout backfill behind pipe-in-tunnel has been gaining increased acceptance in the tunneling industry and has proved to be both practical and economical. Two successfully constructed projects, the Upper Scioto West Interceptor Sewer (USWIS), in Columbus, Ohio and the Benbrook Pipeline Tunnel Project in Fort Worth, Texas will be discussed. The projects represent two different but successful applications of lightweight cellular grout backfill. The USWIS placed the grout behind precast reinforced concrete pipe, in water bearing limestone, and in close proximity to residential water wells. The Benbrook Project placed grout behind 6,096 meters (20,000 feet) of steel pipe from just two locations, eliminating major surface disruption typically associated with the placement of pumped concrete.

Jan 1, 1999

By M. Gaft, G. Panczer

Sedimentary francolite and magmatic apatite are characterized by specific laser-induced time- resolved luminescence, which allows phosphate to be distinguished from accompanying dolomite. The "selective window" parameters are: he, = 337 nm, delay time after laser pulse is 0.5-5 ps, and detection spectral range is 400-525 nm. In the case of nonuniform distribution of phosphate minerals, it makes it possible to accomplish lasero- luminescent sorting and to receive intermediate product with a lowered dolomite contents.

Jan 1, 1999

Cost accounting information is used primarily for (1) planning, control, and performance evaluation; and (2) managerial decision-making. Incremental analysis is a tool for managerial decision-making. It is designed to estimate future financial performance, namely the benefits and costs associated with alternative courses of action. Decisions may be distinguished as pertaining to short-term or long-term activities. Long-term activities frequently focus on capacity decisions and the attendant capital budgeting processes used to quantify the financial effects of these decisions. Short-term decisions typically address short-range production quantity and pricing issues, outsourcing, selection of the optimal mix of products, inventory management, and the acceptance of special orders. This chapter addresses these short-term decisions.

Jan 1, 1999

By Murray Malott

The Sheppard Subway extension is currently being constructed in Toronto, Canada for the Toronto Transit Commission (TTC). McNally International Inc., in a joint venture with PCL and the Foundation Company of Canada were awarded the Twin Tunnels contract of the Sheppard extension. The Twin Tunnels project is approximately 4.4 km in length and consists of two separate twin bore drives each 3.3 km and 650 m in length and approximately 400 m of cut and cover construction. This paper presents a case history of the construction of the soft ground tunnels through the complex Toronto glacial deposits using two 5.9 m outside diameter Lovat earth pressure balance (EPB) tunnel boring machines.

Jan 1, 1999

By A. W. Laughlin, C. R. Mansfield, M. J. Ferris, D. A. Cremers

Laser-Induced Breakdown Spectroscopy or LIBS can be used to provide exploration companies with precise and accurate chemical analyses in the field, in real-time, resulting in major time and cost savings. Using a Field-Portable Analyzer(FPA), anomalies can be followed up immediately while crews are still in the field. Lower limits of detection (LLDs) are element dependent, but many are sufficiently low to be useful in exploration. LLDs in ppm for selected elements of interest are: Be-2, Cu-3, Zn-20, As-200, Sb-500, Pb-30, Ag4,Mo-100, B-33, Ti-500, V-350, and Cr-l. LIBS analyses require little or no sample preparation.

Jan 1, 1999

By T. Guler

Turkey has important celestite reserves in Sivas. These reserves have gypsum and/or calcite as gangue minerals. Celestite-calcite ore cannot be concentrated by gravity methods due to the low efficiency of gravity methods in fine sizes. Research was tried to concentrate celestite to a market grade by flotation. Parameters such as pH, particle size, dosage and types of collector and depressant were examined. Cyanamid A-845 and Na-oleate combination as collector, sodium silicate as depressant, and Aerofroth-65 as frother were found as the optimum flotation reagents. By applying 3-stage cleaning, a concentrate assaying 95,34 % SrS04 was obtained with 84,93 % recovery.

Jan 1, 1999

The role of ZnSO4 in activation of sphalerite (ZnS) and deactivation of lead-activated sphalerite has been investigated. Adsorption of metallic ions at the solid-solution interface, electrokinetic results for sphalerite under different chemical conditions, and thermodynamic calculations were used to elucidate the mechanisms involved. It is shown that flotation response of sphalerite in absence of activators is rather weak and that adsorption of ethyl xanthate on the mineral mainly electrostatic in nature. Zinc sulfate is found to activate the mineral but only in a narrow acidic pH range. This is attributed to the increase of zeta potential as well as the possible increase in amount of negatively charged bulk precipitated zinc xanthate. Lead ions activate sphalerite in a wide pH range and the lead activated mineral assumes a flotation behavior similar to that of galena (PbS). However, addition of ZnSO4 depresses the lead-activated sphalerite by replacing lead ions at the mineral/solution interface.

Jan 1, 1999

By Don Rose

Steel-fiber-reinforced-shotcrete (SFRS) methods of testing and the wording of specifications vary from country to country. In the USA ASTM C1018 is widely used. The Canadians have taken a close look at C1018 and point out that exact determination of the first crack is very subjective, and they propose a method of design that eliminates this variable. The Europeans (EFNARC) have taken the principles of testing a step further than ASTM C1018, and have added a new step in measuring the effectiveness of SFRS. EFNARC uses an "energy absorption" of a plate loaded in its center, in addition to the principles of C1018. The principles of SFRS design are also used in Japan, Norway and elsewhere.

Jan 1, 1999

By T. Mudder, K. Harvey

The objectives for closure of a hard rock mine include minimizing long term environmental liability, attaining regulatory compliance, and maintaining geotechnical stability, while closing as cost-effectively as possible. Proper planning for closure should come during the feasibility study, design and permitting phases, and during operations as updates. The lack of a proper or updated closure plan can result in severe environmental and economic consequences. Effective mine closure is the result of a combination of innovative concepts, long-term commitments, and multi-party cooperation. The purpose of this paper is to discuss concepts, commitments, and cooperation as they relate to an effective closure plan.

Jan 1, 1999

By V. T. Vacariu, P. D. Georgescu, N. Tomus

To assess the potential for radioactive pollution unique to the environmental conditions of the Bacau phosphogypsum waste dump, surface samples were taken, drillings were performed on the entire waste dump's height, and the Ra226 distribution on the height and surface considered to contain a medium content of the radium of 0.57 Bq/gr was studied. Thus, the waste dump's radioactive potential was estimated at 30-40 Ci in equivalent Ra226. Also analyzed was the granulometric composition of the phosphogypsum and the distribution of Ra226 on granulometric orders, which indicated that the radium was concentrated in the very fine fractions. Parameters were set up for the classification by hydrocycloning to obtain a fine class (less than 41 microns) having a radium content of more than 0.9 Bq/gr and a coarse class having less than 0.37 Bq/gr. A chemical process was devised for removal of the radium from the phosphogypsum with the possibility for recovering the contained sulfur.

Jan 1, 1999

By S. Veeramasuneni

The recent nonequilibrium electrophoretic mobility measurements by laser-Doppler electrophoresis coupled with the stability and prevalence of collector colloids in soluble-salt flotation systems suggest that the selective flotation of alkali halides is due to the adsorption of oppositely charged collector colloids by heterocoagulation. Previously reported flotation results confirm this surface charge/collector colloid adsorption model. These results also indicate that the sign of the surface charge has a significant effect on the extent of particle dispersion/aggregation. In this regard, the nature of such particle interaction forces at high ionic strengths are examined to improve our understanding of these systems. Atomic force microscopy (AFM) is now being used to directly measure the interaction forces responsible for the stability of these alkali halide aggregates observed in optical microscopy studies. Results from this study indicate that, while repulsive hydration forces exist between similarly charged hydrophilic particles, attractive forces exist between oppositely charged hydrophilic particles in high ionic strength solutions.

Jan 1, 1999

By C. A. Rowland

Introduction Comminution efficiency, as measured by relating circuit performance to the consumption of energy and the time and money required, can be determined by the following comparisons: Theoretical efficiency: The theoretical efficiency is the actual energy consumed in a comminution machine compared to the theoretical energy required to perform the size reduction. Operating efficiency: The operating efficiency compares the operating work index of a comminution machine to the Bond work index of the ore, as determined from bench-scale crushing and grindability tests or pilot-plant tests. Economic efficiency: The economic efficiency is comparing income from production to predicted income. Key words: Comminution, Bond work index, Grinding, Crushing, Ball mills, Rod Mills. Theoretical efficiency In their book Process Engineering of Size Reduction - Ball Milling, Austin, Klimpel and Luckie (1984) stated that, "We have tried throughout this book to avoid the use of the term grinding efficiency because the degree of conversion of energy to useful size reduction is an ill-defined concept. In addition, the only efficiency, which is of real interest, is the meeting of product specifications at the minimum cost." The National Materials Advisory Board, National Re¬search Council (1981), in the abstract of a report titled "Comminution and Energy Consumption" stated that, "Up to 99% of the energy consumed in grinding these ores may be expended in the movement of machinery, with noise and heat the undesirable byproducts, thus leaving only 1% of the energy available for size reduction. Coupled with this is evidence that many of today's crushing and grinding techniques not only are antiquated but have little or no scientific base of understanding." Throughout the past 50-plus years, grinding efficiency has been referred to as being from 1 % to 10%. The measurable basis for these observations is difficult to establish, but they appear to be based on production performance compared to theoretical energy requirements for the work done. The theoretical energy requirements were determined from the energy required to break a single particle or a thin layer of monosized particles by compression or by a single impact from an impact-testing device. King, Tavaras and Middlemiss (1997), in a paper titled "Establishing the energy efficiency of a ball mill" described such a test. These batch single-breakage tests generally do not duplicate the continuous-breakage process in the comminution machinery used in ore concentrators. Operating efficiency The currently available crushers and grinding mills are fed at a controlled continuous flow rate, and they impart the breakage pattern needed to produce the desired size reduc¬tion. While theoretically inefficient, they are the most practical comminution machines available. The operation of this machinery is relatively simple and can be controlled with available control systems. The essential factors in determining the operating efficiency of comminution machines are energy, as consumed in the machinery, and the required energy, as determined from test work. Bond work indices, obtained from bench-scale or pilot-plant crushability and grindability tests are used in the following Bond equation (Bond, 1960) to determine the energy required to produce the required size reduction

Jan 1, 1999

By Iwao Iwasaki

Since the oil crises in the 1970s, the mining industry in the developed countries has faced strong competition from developing countries. In order for the North American iron ore industry to remain competitive with high-grade overseas sources, research on low-cost beneficiation methods that ensure high-quality and uniform-quality products must be maintained in order to prepare for ever-tightening specifications on iron making raw materials for blast furnaces and also for the future iron- and steelmaking processes that can directly utilize finely ground concentrates.

Jan 1, 1999

By G. Chi, M. C. Fuerstenau, R. C. Bradt, A. Ghosh

Technical Papers, Mining Engineering Vol. 49, No. 12, pp. 70-75, Discussion by McIvor, R. and Fink, R. P. We must challenge what we consider to be dubious statements in the above-mentioned article. Much of what is reported was published elsewhere over a year ago (i.e., in their reference: Chi, G., Fuerstenau, M.C., Brandt, R.C. and Ghosh, A., 1996, "Improved comminution efficiency through controlled blasting during mining," International Journal of Min¬eral Processing, Vol. 47, p. 93). There is nothing unusual or significant about a 10% or more difference in grindability between two materials of apparently similar origin and other attributes (such as chemical assays, hardness and specific gravity). Consider also that: • the materials came from different locations in the pit; • only two sets of four blastholes were considered per blast: • spatial orientation with respect to the face and other blastholes was also altered; • only two pairs of data were collected; • the impact of sampling error and bias, • both of which could be significant in this case; and • normal experimental error in parameter measurement and calculation. It is clearly inappropriate to draw any conclusions with regard to cause-and-effect relationships without first presenting a thorough error analysis. A substantial number of randomly selected test and control areas might provide meaningful statistical evidence of the claimed effect of the variables being studied. Even that appears doubtful, however, because Figures 3 and 4 show about as much variation in crushing energy for the two "regular" conditions vs. regular and altered conditions. On a separate, but also important issue, broad experience with autogenous/semiautogenous milling has shown that smaller or weaker feed material results in reduced tonnage. ? Reply Thank you for the opportunity to respond to the comments of Messrs. Mclvor ant Fink. The points raised are addressed in the order of presentation. As the commenters noted, there are parallels between this article and a previous manuscript. The reason for these complementary articles is that the audiences for the two publications are different, although there is obviously some overlap. We believe that the different audiences each profit from the technical aspects of the two manuscripts. We are not in agreement that a grindability difference of 10% is insignificant. The laboratory work is corroborated by data obtained at plant scale, which confirms that an increase in throughput of the same magnitude (between 5% and 10%) is achieved when the blasting pattern is modified, i.e., reduced from 9 to 8 m (29.5 to 26.2 ft). This increase in throughput translates into substantial power savings for ore grinding. No differences in appearance in the rock were noted between the two adjacent areas. Rock in both areas belonged to the same rock mass/block, which was quite homogeneous and without geological features in between that could create drastic differences in comminution characteristics. Given the resources, we would have sampled from all of the holes. Additional data would certainly have been desirable, as would have been additional funding to expand the study. Their comment, "spatial orientation with respect to the face and other blastholes was also altered," is not clear. Figure 1 does not show the initiation sequence. Without the initiation sequence, we do not understand how the commenters concluded that spatial orientation with respect to the face and other blastholes was altered. The commenters may be trying to make the point that the four-hole configurations with respect to the original bench face are not exactly the same. In fragmenting the

Jan 1, 1999