Search Documents

By D. Carlson

At the Freeport Indonesia Grasberg Mine in Irian Jaya, Indonesia, a system of underground drainholes and surface drain wells have been designed and are currently under construction. The underground drainholes are located at elevations of approximately 9,600 feet and the surface drainwells located at elevations ranging between 12,500 and 13,000 feet. Together they will be used to drain the ground water contained within relatively incompetent rock. This drain system will allow for the successful dry mining of the open pit, and provide slope stability of the pit wall. The surface drain well network, when completed will allow for the draining of ground water to the Amole Drift where the underground drainholes are constructed.

Jan 1, 1998

By C. Waddell

PDMI mines five different grades of ore. Shovel operators were experiencing problems differentiating one material type from another. In 1997 PDMI decided to try GPS ore control to aid operators in identifying material boundaries. Computer generated ore control maps and GPS data defining the shovels' position is fed to a computer on board the shovel. A monitor, located near the shovel operator, displays material types, their boundaries, and the shovels' position and movement in relation to the mining face. This information has reduced errors in material identification by 50%.

Jan 1, 1998

By Mary Korpi

So now you ask, Where are the transcripts? The well-organized co-chairs, Harry and Mary, did their job. Doug Halbe was active in the audience encouraging people to speak up and keeping everything moving along. So where are they? Were the comments so provocative that they could not be written? Was the profanity so bad (even for miners!) that it couldn't be repeated? It appears that at the first session of the Plant Operators' Symposium a glitch occurred with the recording equipment. Thanks go to everyone who did comment during the dis- cussion period. The People I session had a lot of lively conversation and we are sorry that it will not be printed. However, there is now another reason to hold the plant operators' sessions on a regular basis! Another People session can and will be held in the future.

Jan 1, 1998

By C. R. Stephan

There are a large number of facilities throughout the world which handle coal, such as preparation plants. Many other facilities use coal as a fuel, such as cement and lime factories. Although coal can be handled safely and can be an efficient fuel, there are explosion hazards which are accentuated as the particle size is reduced. Particle sizes of coal which can fuel a propagating explosion occur within thermal dryers, cyclones, baghouses, pulverized-fuel systems, grinding mills, and other process or conveyance equipment. This paper discusses how explosions can occur within these facilities.

Jan 1, 1998

By Anthony D. Hammond

INTRODUCTION A two-dimensional approach for modeling narrow-vein deposits using the TECHBASE® software was implemented at Sunshine Mining for its use in the evaluation of mineral properties. This 2-D approach prevents the overestimation of high-grade tons typically associated with the use of fixed 3-D blocks and reduces the size of the model in computer memory. The method consists of constructing a two-dimensional model oriented along the average plane of the mineralized structure. This approach works well for single, multiple and intersecting veins with the condition that each vein is roughly planar with variation in dip or strike less than 30" in order to maintain a reasonable resolution in the process of projecting data onto a plane (Figure 1). Also, a precise identification of the hanging-wall and foot-wall location is critical in ensuring an accurate representation of the vein. By using various modeling techniques, the two-dimensional model estimates metal content, thickness, tonnage, economic and dilution parameters which will be ultimately used in the identification of minable reserves. The following is a generic description of the steps involved in modeling a steeply dipping vein. DATA ENTRY A typical project database consists of drillhole coordinates, survey information, assay data and any other quantitative or qualitative data. This database can be created inside the software or imported from any spreadsheet. TECHBASE® utilizes the concept of "fields" and "records" (columns and rows) for storing data. The use of "calculated fields" enables the user to expand on the manipulation of the database with minimum memory requirements. Another important feature of TECHBASE® is the ability to replicate the structure and format of the "tables" for its use in another project and the capability of running a series of repetitive tasks by means of batch and "runlog" files.

Jan 1, 1998

By F. J. Sotillo

The objective of this investigation was to determine the feasibility of using a high-pressure roll mill (HPRM) to improve the separation efficiency of dolomite from apatite in downstream operations when treating high-dolomitic pebbles. High-dolomite samples from four phosphate mines were used for the test program. The research work plan included sample characterization studies; INSTRON tests to develop preliminary crushing data; high-pressure roll mill evaluations to determine crushing parameters, such as feed rates, rolls speed and gap, and applied torque, pressure and energy; and screen, microscopy, and flotation studies to assess dolomitelapatite separation efficiency. The results of the HPRM tests show that commercial products for all four mines can be obtained. Recoveries of 74-82% of the P2O5 and rejections of 46-83% of the MgO were reported with an specific energy consumption of 0.2-0.5 of that of a laboratory rod mill.

Jan 1, 1998

By A. F. Symonds

The effects of harmonic resonance between the supply impedance and power factor correction capacitors on systems with large harmonic sources, such as mine winders, are well known. The similar effects of resonance with cable capacitance are not commonly encountered and, hence, are not always considered in the design of medium-voltage networks. This article considers some of the aspects of resonance between the supply impedance and the cable capacitance and presents one successful approach to solving the problem.

Jan 1, 1998

By Laura J. Carroll, Gordon A. Goldsmith

Experts, like many of the speakers at the SME Annual Conference, are frequently called upon by lawyers to assist them in litigation. Due to the technical nature of many cases, the testimony of an expert with knowledge and experience in a particular field is necessary to help a judge or jury understand and decide certain issues. Environmental litigation is no exception. Experts routinely are called upon to offer testimony to establish the existence of contamination and its source, as well as the potential health and environmental risks associated with the contaminants. This article will briefly discuss the factors courts apply to determine whether to admit expert testimony after the recent Supreme Court decision in Daubert v. Memell Dow Pharm., Inc., 509 U.S. 579 (1993). The Court's decision in Daubert overruled a long-standing test that had based the admissibility of scientific evidence on its "general acceptance" in the field in issue. Next, the article will discuss in general terms what a party must do to "link a particular defendant's conduct to the contamination involved in order to recover from that defendant. This link, known as causation, varies depending upon the type of claim being asserted. Expert witnesses are used extensively to help establish causation. JUNK SCIENCE OR GOOD SCIENCE- HOW DOES A COURT DETERMINE WHAT TO LET IN A frequent complaint in litigation involving technical or scientific issues is that one party or another is trying to use so-called "junk science" to prove its case. While some expert testimony might be so clearly lacking in support or so "off the wall" that a court can easily determine to exclude it, other testimony, especially testimony on the "cutting edge," is much more problematic. In 1923, the District of Columbia Circuit Court of Appeals decided the case of Frye v. United States, 293 E 1013 (1923). In deciding whether to admit certain expert testimony, the court in Frye stated that while a court will "go a long way in admitting expert testimony deduced from a well-recognized scientific

Jan 1, 1998

By Ronald J. Doll

The selection and matching of the conveyor drive components (Figure 1) determine the initial cost, long term costs, and how well the drive performance is matched to a project's long term production goals. This paper will cover the specification criteria and considerations that should be included in a conveyor drive specification. It will also review the practical aspects of the specification's intent and the solicitation of alternatives.

Jan 1, 1998

By C. G. Roache

Mining legislation in Jamaica dates back to only 1947 when, on August 30 of that year the Minerals (Vesting) Act was promulgated. None of the exploratory and trial-mining projects over the preceding 450 years were regulated or controlled by law. It was the seriousness of the intent of the North American Aluminum Companies to establish a bauxite mining industry in Jamaica which led to the development of the first piece of mineral legislation. It is of note that the incoming mineral industrialist was more anxious than the Government to see that a legislative framework was in place. It was relevant then as it is today for good mining legislation to be in place for the Government to regulate and control the exploration and exploitation of mineral resources. It was also necessary for the industry to know their rights and obligations so that they could plan, explore and exploit with some assurance that their capital was secure. One of the main reasons that the mining of bauxite did not begin in Jamaica until 1952 was that no legislational framework existed prior to 1947. The Jamaican dollar is tied to the US Dollar at a rate of J$35.00 to US$1.

Jan 1, 1998

By Daniel Hodouin, Claude Bazin, Sami Makni

SCOTT COULTER: Thanks, Eric. Thank you all for coming. Our first speaker today is Claude Bazin. Claude received a degree in metallurgical engineering in 1980 from Laval University in Quebec. He worked for a short time in a mineral processing plant and then returned to Laval to complete graduate studies in the field of process modeling and control. He obtained his master's degree in 1983 and his Ph.D. in 1990. In 1987 he joined Brunswick Mining, New Brunswick, as research metallurgist and subsequently process control engineer. In 1990 he joined Helzfield Mines, New Brunswick, as senior metallurgist. In 1991 he accepted a position of professor at the department of mining and metallurgy at Laval University, a position he is still holding. He's a member of the CIM, TMS, and the Society for Mining, Metallurgy, and Exploration. Claude's topic today is "On-Line Material Balance for Flotation Plants." INTRODUCTION CLAUDE BAZIN: During the last two decades, the on-stream analyzer (OSA) has gained the stat& of key instrument for the control of flotation plants. The OSA is currently used in almost every sulphide flotation plant (Leroux and Franklin 1994), and its application to oxide mineral flotation plants is increasing. The OSA assays are sent to the flotation operators via an operator console or to control loops of various degrees of complexity (McKee 1991) implemented in a distributed control system (DCS). Operators and/or controllers take control actions based on these assays to ensure an adequate operation of the plant. Although this application pays off very rapidly for the purchase of the OSA, one could ask, "Could we get more from the OSA?" Some plants reported the use of OSA measurements for process optimization (McKee 1991). The optimization strategy is based upon economic indices calculated from metal recovery using the 2-product formula (Wills 1992, p. 124). The 2-product formula is sensitive to measurement errors in the assays and can lead to considerable scatter in the calculated indices (Hodouin et al. 1993). Least squares algorithms provide a robust alternative to filter out measurement errors (Spring 1992). This paper presents some applications of a recursive least squares algorithm that provides real-time estimates of the mass flow rates within a flotation plant using OSA and mass flow rate measurements.

Jan 1, 1998

By N. Del Bel Belluz

Drilling underground in the Grasberg De-watering drifts has routinely hit water aquifers with high flow rates and pressures. Two types of holes are utilized; pilot-holes to probe ahead of the tunnel development to intersect aquifers ahead of the face; and de-watering holes to de-water rock formations that will drain water from the Grasberg pit and allow tunnel development to proceed safely. Recently, rates of 1050 psi static pressure have been recorded with flows from a NQ hole measured at 1350 gpm (US). The water flows can be slightly acidic, necessitating the use of stainless steel collar gear to resist corrosion. These rates were anticipated and contingencies were planned early to deal with these conditions. The collar gear is used to control water flows whereby the water is treated as an important resource. As a result, pm has established procedures to maintain safety of the drill crews, enable coring of the rock and to maintain safety of the miners who are driving the drifts.

Jan 1, 1998

By W. A. Crosby

The ability of open pit mines to steepen overall final wall angles allows significant cost reductions as a result of reduced waste movement requirements. Final wall angles are principally controlled by three factors: geological conditions; hydrological conditions; and wall control blasting practices. The first of these factors is not controllable by the mine operator, the second can be influenced to some degree, but the last one certainly can be controlled, hence the current interest in final wall blasting practice at many mining companies. This paper discusses common blasting techniques employed to steepen final pit walls and outlines the attractiveness of moving from small hole high cost systems to the use of full size production drills as a means of reducing wall control blast costs. Attempts to make this change have been limited at many mines by the physical size of the drills and their inability to reverse drill. In the past, pres pi it, pre-shear or trim holes have had to be drilled vertically, at considerable distance from the upper bench toe, with the result that inter-berm face stability is reduced and final wall angles have to be made somewhat more shallow than desirable. The paper concludes with a description of how these problems can be overcome by utilizing the new Bucyrus 39R which has the capability of drilling at a ?15 degree angle underneath the machine. It is concluded that the resulting wall control blast designs will offer large mines improved final wall angles with resulting significant overall cost reductions.

Jan 1, 1998

By W. Irwin

Global warming hitherto viewed as a distant threat to the environment, is now the subject of fierce goo-political debate. The debate centres around the time frame required to achieve environmental compliance, and the cost implications of meeting that objective. Since coal is the fuel of choice for power generation, the priority objective of energy producers is the pursuit of environmental protection measures that allow coal to be burned without any attendant negative impact on the environment. From an environmental point of view, public attention is today firmly focused on the impact that all industrial activity has on the environment, and coal is singled out from other fossil fuels as being the product of an inefficient smokestack industry. Despite coal's poor public image it is unrealistic to suggest as some do, that use of this fossil fuel as a primary energy source should be drastically curtailed. Coal which already generates about 35% of the world's electricity is continuing to increase its share of this rapidly expanding market, and to argue against its use is flying in the face of reality. However, changes are required in the way coal is used in some of the new clean coal technologies, since many include advanced methods of combustion. Indeed changes in the way coal is used is a vital link to the future of coal as a primary source of energy, and increased coal utilization will be directly linked to changes in its use. Discussion of various issues that affect coal utilization are the focus of this paper.

Jan 1, 1998

By A. Mayton

The prolonged exposure of equipment operators to shock and whole-body vibration (WBY) is linked to cumulative back, neck, and abdominal disorders. In low-coal mines, space restrictions make seat suspensions difficult to use in isolating operators from shock and WBY. Researchers at NIOSH, Pittsburgh Research Laboratory, are responding to these issues by investigating viscoelastic foams. For the full-load case. an ergonomic seat with viscoelastic foams isolated the shuttle car operator from shock at 15Hz. Researchers used results from additional foam testing with an analytical model to identify viscoelastic foams that provide shock isolation at a frequency below 5 Hz.

Jan 1, 1998

By Richardo Montoya

Radomiro Tomic, the new CODELCO division, is a copper deposit located at 3000 m a.s.l. and 40 Km from Calama in northern Chile. It has total oxide reserves of 802,000,000 tonnes with an average grade of 0.59% total Cu (using a cut-off grade of 0.4% total Cu). The copper oxide ore is mainly atacamite and chrysocolla. Startup is expected to commence in December 1997 of 150,000 t/y of Cu cathodes. Future expansion to 250,000 t/a of Cu cathodes is currently being planned. The process consists of an open-pit mine, a two-stage crushing system, agglomeration with sulphuric acid and emplacement on a heap leach pad for a 45-day leaching cycle. Solvent extraction and electrowinning will produce LME "A grade cathode. A number of significant technology innovations have been incorporated into the project.

Jan 1, 1998

By N. Edmonson

During the last 30 years, a dramatic increase in the supply of byproduct sulfur substantially reduced the share of the market held by Frasch-mined (non-by-product) sulfur in North America. Even though Canadian sulfur production is not discretionary, the geographic remoteness from the large US markets and the high transportation costs associated with delivering sulfur to those markets has meant that Canadian producers act like discretionary producers in many important ways. They have effectively replaced the US Frasch producers as the cost-marginal sulfur source to large US markets. Implications of this change in market structure include more volatile sulfur prices and longer sulfur price recessions.

Jan 1, 1998

Projections of coal reserves in Central Appalachia are essential for long-term planning in the region. Annual production is declining in some states, such as Virginia, and mineable reserves for the Central Appalachian Coalfield are challenged by difficult geological, mining, and market conditions. In order to project coal mining longevity in this region, interviews with mining companies were conducted to assist in the determination and assessment of technical and economic factors that impact coal seam mineability. This information was applied to seam and coal reserve data developed by state and federal governments. The results were carefully analyzed to determine the effects of various factors on the overall mineable coal reserve base.

Jan 1, 1998

Early experiences suggested autogenous mills were difficult to operate and consumed substantially more energy than conventional rod/ball mill circuits. As our understanding has increased and the technology has matured this perception has changed to the point where most new comminution circuits are ag/sag based. In addition many operators have replaced existing conventional circuits with this technology. The JKMRC has been studying ag/sag mills for over 20 years. During this time it has amassed what is probably the single largest and most detailed data base of pilot and full scale mill operations in the world. This has been used to help develop and refine its cur- rent commercially available mathematical model of ag/sag mills. A decade of its application has greatly helped simplify both design and operation of ag/sag milling circuits as well as helping to promote the effective use of recycle crushing, secondary crushing and closed-circuit operation. This paper describes the development of ag and sag milling in terms of our understanding and the evolution of the technology. In addition the application of mathematical modelling and simulation in designing and operating efficient circuits is described with the aid of practical examples.

Jan 1, 1998

By H. J. Chen

In recent years, it has been recognized that the high horizontal stress is an important factor that contributes to a cutter roof. When the immediate roof is thinly bedded, the presence of a high horizontal stress may first cause failure on the bedding planes or weak planes, and then a cutter roof develops as the individual stratum crushes and buckles progressively layer by layer. In this study, the stress distributions in the bedding planes of the immediate roof are analyzed for an entry-pillar system in the multiple longwall panels by using the finite element method. Then the roof failure is analyzed based on the rock failure criterion and the stress distributions.

Jan 1, 1998