Search Documents

By C. W. Schultz

Earlier publications from The University of Alabama have indicated that column flotation performance is improved when operating at low pulp levels and when the feed is directed into the froth phase. To validate these early observations a series of tests were performed in which the position of the feed entry to the column and the pulp-froth interface were systematically varied. The optimum grade-recovery relationship was achieved with high feed entry (WA) of column height) and very low pulp levels (<10% of column height). The position of the pulp-froth interface appears to be the more critical variable. When operating in this mode (1. e. at low pulp levels) column flotation becomes. in reality. a froth separation process.

Jan 1, 1991

By H. Akgun

Design of plugs for abandonment of boreholes and shafts may be governed by the bond strength between the plug and host rock. This paper presents the results of push-out tests on cement grout plugs in salt. Two expandable cement grouts have been tested. The average interface shear strengths ranged from 2 to 12 MPa. Peak shear stresses at failure, assuming an elastic stress distribution along the interface, were up to eight times higher. Standard deviations commonly reached 20%. Dissolution along the interface was observed, and may have been enhanced by clay inclusions in the salt. This dissolution appears to have reduced bond strengths. Application of the results to the design of plugs for larger openings (e.g. shafts, drifts, or boreholes) is discussed.

Jan 1, 1991

By Julian Boldy

The discovery of the Delbridge massive sulfide deposit in the Noranda district of Quebec resulted from an appreciation of the significance of a mercury leakage haloas a lithochemical pathfinder to blind ore, coupled to its location relative to a geologically inferred ore-bearing horizon within complex volcanic stratigraphy. Systematic sampling of microfractures present in outcrops delineated a diagnostic anomaly, drawing attention to an area considered prospective for buried ore. The massive sulfide deposit was subsequently found to be blind and topped at the 107-m (350-ft) level. This case history is presented in the context of its time and was the first volcanogenic ore deposit to be discovered utilizing mercury as a pathfinder in the Canadian Precambrian. The case history also illustrates that the practical application of an innovative technique coupled to a new geological interpretation can result in success, even on a property that was centrally located in a mining district and had undergone intensive exploration efforts over a 38-year period.

Jan 1, 1991

By Danqing Xu, A. W. Khair

This paper presents an analysis of mechanism of secondary fragmentation and respirable dust generation due to regrinding. In continuous miners, the recovered coal and uncleaned coal from the previous cutting cycle have to be transported through the circumference of the cutting drum, subjecting the coal to regrinding. Such regrinding comminutes the coal material utilizing kinetic energy, thus creating a great amount of respirable dust. The mechanism of a single particle subjected to regrinding is analyzed. A mathematical model is developed to describe regrinding in field conditions. The important factors influencing the comminution process are discussed in detail. Utilizing three types of coal seams, laboratory experiments are being carried out with an Automated Rotary Coal Cutting Simulator (ARCCS) to quantitatively evaluate the effects of some particular parameters, such as cutting velocity, depth of sump and properties of coal material, on breakage and on the amount of respirable dust generated. An orthogonal fractional factorial experimental arrangement is used to optimize experimental design. Preliminary experimental results are presented.

Jan 1, 1991

By Paul B. Queneau

Formulation and commercial utilization of solid-waste incinerator slag by-product is the focus of this paper. Particular attention is given to iron aluminosilicate melts having compositions similar to that of nature&apos;s basalt The earth?s crust can be viewed as an environmental laboratory for predicting stability of various silicates; small-scale laboratory experiments are necessary to confirm findings there from. An ideal slag consumes flux additives at acceptable cost, is compatible with furnace refractory, flows readily from the furnace, and has physical properties suitable for its commercial utilization -all within the critical constraint that the slag is environmentally stable. Examples of successful solid waste slagging practice, including tonnage, utilization and pricing, are provided from metallurgical and waste treatment operations of North America. Western Europe and Japan.

Jan 1, 1991

By Howard G. Coopersmith

A resource of low grade good quality diamonds has been discovered through the Diamond Company NL-Moonstone Diamond Corp. Joint Venture. A limited bulk sample diamond test of two large kimberlite pipes on the Kelsey Lake Property, Colorado, has been completed. These kimberlite pipes have petrological and mineralogical indications of the presence of diamond. Small diamonds were recovered from surface samples. Drilling and trenching revealed both pipes were complexes of diatreme facies kimberlite. One pipe contains crater facies kimberlite as well. This is the first reported occurrence of crater facies kimberlite in the Province. Approximately 1000 tonnes of kimberlite rock was excavated and processed through a scrubber -HMS -Sortex -Grease Plant. Significant diamonds were recovered. The diamonds were generally of good color and clarity, with many being in the gem and near gem categories. Grades are considered low however. Additionally, a small potential resource of alluvial diamonds is present.

Jan 1, 1991

By David E. Thompson, Daniel J. Dobbels

INTRODUCTION The planning process for projects requiring construction of tunnels in urban environments can be highly complex and involves interaction with professionals of many disciplines. Typically the initial step in the planning process is to establish basic design criteria for the tunnel or tunnel system consistent with its intended purpose. Such criteria might include acceptable tunnel geometry, minimum and maximum slope or other associated criteria. Ideally, once the basic criteria have been established, the next step in the process might include establishing technically feasible horizontal and vertical alignment and shaft siting alternatives and developing "ball park" construction and operational cost estimates for the alternatives. Comparisons can then be made regarding the relative technical and economic merits of the alternatives and the most favorable alignment(s) are selected for further study or preliminary design. Typically the last and perhaps the most important task that is conducted during the planning stage includes identifying issues and potential problems to be addressed during the design and construction stages of the project. Many issues warrant consideration during the planning phase of a tunneling project. For the purposes of this paper, these issues can be divided into two broad categories: technical and non-technical. Important technical issues include, among others, general design criteria, geotechnical and geoenvironmental issues, and constructibility issues. Important non-technical issues include, among others, right-of-way and easement related considerations, project scheduling constraints, both short and long term environmental impacts and overall cost/benefit aspects of the project. With respect to influence on the planning process, these two groups of issues often cannot be separated completely. For urban tunneling projects, however, it is most often the case that the non-technical

Jan 1, 1991

By Z. Eisenstein, H. K. Heinz, F. M. Kuwajima

Due to its complex rheological behaviour, shotcrete induces a ground-structure interaction that differs significantly from other types of tunnel linings. For the same reason, the instrumentation of shotcrete linings presents special problems, particularly when it comes to estimating the stresses transferred to the lining during construction. The shotcrete characteristics which affect the stress distribution are initially discussed. Measurements obtained in a recent soft ground tunnel are also presented. The conclusions are aimed at introducing practical recommendations for the design of tunnels where shotcrete is used as initial and/or final support.

Jan 1, 1991

By Frederick T. Graybeal

Silver Bell is located about 56 km (35 miles) northwest of Tucson, AZ. It is a classic porphyry copper deposit containing enriched disseminated chalcocite ore in altered porphyritic rocks with chalcopyrite in adjacent skarn zones. The discovery of Silver Bell was an evolutionary process that occurred over a 75-year period. Recorded mining activity began about 1865 on Boot Hill east of El Tiro pit (see Fig. 1) where outcrops of altered limestones were found to contain 425 to 482 g (15 to 17 oz) Ag mixed with copper oxides. By 1874, the Young America Copper Co. was mining shallow occurrences of 30% Cu along the north side of the present Oxide pit. The ore was shipped by wagon to Yuma, AZ, and then by boat to San Francisco for smelting. By 1881, the district supported several mining companies, two small smelters, and was being favorably compared to Bisbee in local newspapers. Most of the ore mined in the period 1865-1903 came from pods of massive sulfide or their oxidized products which were distributed in an unpredictable fashion through a large skarn zone in Paleozoic limestone east of El Tiro pit. Ore grades varied from 5 to 10% Cu.

Jan 1, 1991

By Deepak Malhotra, Robert Dorfler

Modern engineering mill design has been refined over the years to the point where detailed ore and process specification criteria can be developed In the engineering design phase of the project. The plant Is then built to the detailed criteria and performance acceptance tested by the owner to see if the as-built mill meets the criteria, This performance testing is critical to the owner; the test must be systematic with sample collection coordinated throughout the plant. Despite the availability of systematic approaches to plant development, the new plants often fall short of design criteria. This paper discusses the key Issues a Project Manager/Process Engineer should Implement to ensure that plants meet design criteria.

Jan 1, 1991

By F. Calizaya

This study summarizes the results of various numerical and laboratory experiments per-formed to study the effect of airflow recirculation on gas concentration. The numerical exercises were carried out on a simulated mine ventilation net-work. The laboratory experiments were conducted at the Mackay School of Mines&apos; airflow monitoring system in Reno, Nevada. In both cases, the airflow was recirculated through the system by means of a main fan and a set of booster fans. The booster fans were positioned to produce two types of recirculation: In line and Cross-cut. For each type, various recirculation conditions were generated by changing the booster fan pressure. During each test, the gas emission rate at the simulated working face was kept constant. The study illustrates the conditions under which controlled airflow recirculation may be used to solve a district ventilation problem.

Jan 1, 1991

By Y. David

In 1990, the United States became only the second country (after China) to produce more than 900 Mt (1 billion st) of coal in a single year. US production of bituminous and subbituminous coal, lignite and anthracite totaled 933.5 Mt (1.029 billion st) in 1990, 5% more than in 1989. The production gains were largely due to the rebuilding of depleted coal stockpiles by electric utilities and a surge in US coal exports. Domestic coal consumption essentially remained at its 1989 level. A slight increase in electric utility coal consumption was partly offset by a decline in metallurgical coal use. The use of coal in other industries and in the residential-commercial sector remained virtually flat.

Jan 1, 1991

By James R. Norris, Thomas A. Conto, Gary R. Walter

For at least five decades, a plume containing acidic metal-bearing water has been moving through the shallow alluvial aquifer along Pinal Creek in the Globe-Miami area. Two chemical facies of water are distinguished in the alluvial aquifer: (1) a metal-rich acidic plume with gram per liter concentrations of metals (primarily iron) and pH values between 3 and 5 and (2) neutralized water with a pH greater than 5, low concentrations of metals, and high concentrations of sulfate and manganese. Historically, the acid plume has moved through the aquifer at an average velocity of 0.6 m/day, ten times slower than the average pore velocity of groundwater in the aquifer calculated using the Darcy equation. The rate of migration of the metal-rich plume is retarded by pH-dependent chemical reactions between acid water and the aquifer matrix. As acid water is neutralized by reaction with calcite, rising pH conditions in- crease the oxidation rate of iron and decrease its solubility resulting in the precipitation of ferric hydroxides. The formation of ferric hydroxides is a proton releasing reaction which main- tains acidic conditions. The acidit of the plume and the neutralization capacity of tKe aquifer are best assessed in terms of the iron content of the water and not the hydrogen ion activity computed from pH measurements. The parameters controlling plume migration are: (1) the calcite content of the aquifer (2) the iron acidity of plume water, and (3) the rates of acid neutralization and ferrous iron oxidation. A numerical solute transport and reaction model based on the concept of iron acidity effectively simulates the historical development of acidic conditions, predicts the behavior of the plume, and was used as a management tool to identify the most efficient and cost effective remedial strategy.

Jan 1, 1991

By M. R. Yalamanchili, W. H. Jang, Y. Ye, J. D. Miller

Typically, rougher molybdenite flotation and recovery from bulk copper/molybdenum concentrates involves the use of alkalisulfides, Nokes reagents, cyanides, oxidants, and/or thermal treatment to depress copper sulfide minerals. The bulk copper/molybdenum feed generally varies from 0.2% Mo to 1.0% Mo, and with traditional reagents the single-stage rougher flotation recovery of molybdenite varies between 40% and 90% at a concentrate grade of 5% to 10% Mo. With ozone conditioning for copper depression, however, improved separations appear to be possible, as demonstrated by tests with Cu/Mo concentrates from both the Phelps Dodge Morenci Operations and the Kennecott Copperton Operations. Single-stage rougher flotation after ozone conditioning can provide a molybdenum concentrate at a recovery of more than 90% and a rougher concentrate grade higher than 20% Mo in some cases. Subsequent cleaner flotation with additional ozone conditioning resuIts in relatively copper-free molybdenum concentrates containing as much as 52% Mo. Preliminary analysis indicates that, with a multistage ozone conditioning/fotation strategy, the process is technically and economically viable and should be suitable for industrial ap¬plication.

Jan 1, 1991

By Jeong-Heum Kim, Jan M. Mutmansky

The primary purpose of the research summarized in this paper was to experimentally investigate the performance of numerous mine ventilation network iterative solution procedures under controlled conditions to determine which procedures were most favorable in terms of number of iterations and total computational speed. The solution methods investigated included: (1) the Newton-Raphson method, (2) the Hardy Cross method, (3) the linear theory method, and (4) the second-order approximation method. The first three of these methods have been widely used while the fourth was formulated by the authors to investigate its potential for ventilation network computation. In addition to the four solution procedures, three methods for selecting the branches in the meshes and three methods for ordering the meshes for computational purposes were also studied during the investigation. As a result of these various options, a total of 36 combinations of solution methods, mesh selection procedures, and mesh ordering schemes were studied. To investigate the performance characteristics of these combinations, an identical set of 180 randomly chosen ventilation networks was used in sets of 30 networks at six different levels of complexity. Here, the level of complexity is defined as a function of the size (number of branches) and the density (number of nodes compared with the number of branches) of the network. To eliminate variations in the solution times due to differences arising from the fans, a single fan with a fixed characteristic was utilized in all the experiments. This paper will deal only with the results for the four iterative methods used to achieve solutions to the mine ventilation networks. The minimum-resistance spanning tree method for mesh selection and random mesh ordering was used throughout the analysis. The conclusions will be based upon a detailed accounting of the efficiency of each method using the total time to achieve a solution to each problem and averaged over the total problem set. However, the number of iterations and the time to complete each iteration will be studied in order to better understand the solution procedures.

Jan 1, 1991

By M. Rossi

The use of service variables in geostatistics (grade-thickness) is common in industry when developing block grade models and geologic resource estimates. This is particularly true in the case of sedimentary and strata-bound-type deposits. The approach has proven merits when assessing ore reserves. However, there are cases where its application for preliminary data analysis produces biased estimates. One such case is encountered in uranium disequilibrium studies. This paper demonstrates the inadequacy of service variables when performing uranium disequilibrium studies. Disequilibrium analysis is a necessary pre-processing step when radiation counts are used as raw data to calculate uranium reserves. Typically, a probe is used to obtain the gamma counts from open drill holes. These counts are then regressed (and corrected) against chemical assays obtained from core samples. During this process, the grade-thickness variable produces an optimistic image of the relationship between probe grades and chemical (true) grades, causing overestimation of the final geologic resource. The problem is analyzed through a case study.

Jan 1, 1991

By Robin J. Hickson

The Grasberg copper-gold deposit was discovered in the spring of 1988, one year before the planned closure of Freeport Indonesia&apos;s original Ertsberg openpit copper mine. In spite of Grasberg&apos;s remote location, 600 m (1968 ft) above the Ertsberg, atop a hitherto inaccessible mountain, Freeport-McMoRan brought its latest open-pit mine into production in the last week of 1989, less than two years after discovery. Freeport Indonesia&apos;s (FI) copper-gold mining operations are located in Irian Jaya, the easternmost province of Indonesia on the western side of the island of New Guinea. Fl&apos;s six ore deposits are all located within a 10- x 10-km&apos; (3.9- x 3.9-sq mile) Contract of Work area. They are all between the elevations of 2900 and 4300 m (9515 and 14,100 ft) above sea level, some 96 km (60 miles) from the island&apos;s southern coast. A 118-km (74-mile) access route connects FT&apos;s port site of Amamapare on the Arafura Sea to the project area. The first section is an 18-km (11-mile) barge waterway. The final 100-km (63mile) is a two-lane gravel highway. The highway terminates 9 km (5.5 miles) beyond the FI townsite at the project&apos;s central mill, some 2850 m (9250 ft) above sea level. The mining areas are separated from the mill by a 780-m (2560-ft) sheer cliff face. The world&apos;s longest free span tramway system, with a total length of more than 1.6 km (1 mile), is the only means of access for men and materials between the mill and the surface mines. Weight restrictions for the tramway for equipment considered for the project are 15.4 t (17 st). The minimum clear width dimension of two tunnels along the portsite access road is 5.6 m (18.4 ft).

Jan 1, 1991

By E. A. Devuyst

A unique process for removing cyanide and base metal complexes from industrial waste streams was patented by Borberly et al. (1984). The process uses S0, (liquid or gas, or solutions of sulfite salts, or from burning elemental sulfur), plus air that is dispersed in the effluent using a well agitated vessel. Acid produced in the oxidation reactions is neutralized with lime at a controlled pH generally in the range 7 to 10. The reaction requires the presence of soluble copper as a catalyst that can be supplemented by copper sulfate if necessary. The process can be applied to the detoxification of gold and silver mining waste streams, such as carbon-in-pulp (CIP) tailing pulps, barren solution bleeds, pond waters and heap leach rinse solutions and also to plating shops waste waters. The S02/Air process has substantial advantages over two of the main alternative methods of cyanide destruction, namely alkaline chlorination and hydrogen peroxide. Alkaline chlorination is highly penalized in terms of reagent consumption. Chlorine is a strong oxidant reacting with species other than cyanide present in the effluent such as thiocyanate and sulfides. Furthermore, alkaline chlorination is an incomplete detoxification process. Iron cyanide is not removed and the potential for harmful byproducts species exist. Consequently, final effluents may be subject to additional treatment in order to comply with regulatory demands.

Jan 1, 1991

By Rodrigo Jerez

Advances in inexpensive computer automation led to the development and use of a computerized ore control system at the Cyprus Copperstone Gold Mine near Parker, AZ. These new ore control practices improved accuracy, performance and productivity of the ore control effort. An automated system for data collection, including bar coding of blasthole samples, laboratory analysis, data management, grade estimation, cut delineation and ore zone stake out, plays a major role in ore control practices. This is of particular interest because of the large amount of blasthole information being processed, analyzed and reported daily. Copperstone Gold management has been progressive toward new, efficient methods regarding ore reserve estimation, long-term mine planning, short-term mine planning, ore control and surveying. Technological advances, including powerful personal computers, applicable mine planning software and surveying instrumentation, have become readily available and affordable. The computerized ore control procedures used at Copperstone include sample data collection, laboratory automation and computerized data management. These have reduced the time to complete ore control on a blast pattern by 50% to 75%. The final product - ore control - is generated in a more timely and accurate manner.

Jan 1, 1991

By Liu Cheng-si

The number of control plans for placing control devices in a ventilation network is surprisingly large, but the research result indicates that not all control plans are feasible. The feasibility of a ventilation network control plan depends on two factors. One is the influence of the network structure. The structure must contain one independent variable-flow airway in a non-controlled loop. Otherwise, the control plan is unfeasible. The other is the combination of the air resistance, quantity, pressure and other parameters. Under some conditions, the selected values of these parameters may result in an unfeasible plan. As to the influence of the network structure, when the network structure is simple, the feasibility of a control plan can be judged directly. However, for the influence of the parameters, the feasibility of a control plan must be examined through calculation. The control position has been extended into the natural-splitting subnetwork from the conventional constant-flow subnetwork. This technique is theoretically significant. The extension of control positions results in a great increment in control plans and variation in parameters. At present, the calculation methods of the ventilation network control plans are all available. They are quite useful in selecting desirable plans. However, among the plans found, some are impractical or even unfeasible. If the unfeasible ones can be eliminated at first, much time can be saved in design and calculation. This also facilitates management and decision making.

Jan 1, 1991