Search Documents

By Davar Abi-Zadeh, Cillian Brown, Deepak Kandra

"Grout backfill strategy for a particular subsurface concrete tunnel (~4.9km long, 3.5m in diameter, carrying 20” gas pipeline) was based on achieving 1:100 slope of the fill in order to progressively fill the tunnel, in a series of 350m section. Grout rheology, particularly its non-Newtonian and thixotropic behavior, determines the final fill slope for given backfill strategy. The objective of this study was to simulate the two-phase grout mix backfill process using Computational Fluid Dynamics (CFD) and determine the slope of the fill to validate and optimize the backfill strategy. Three dimensional CFD study showed that for a 500m long tunnel section with a single injection point of grout, given its rheology, it will likely keep flowing without filling the 500m section height wise. Design optimization for filling was carried out using two dimensional studies to make the backfill process “slope independent” by incorporating a 2.5m high bulkhead at ~1,000m. INTRODUCTION As part of a gas field development a 20” onshore gas pipeline is required from the landfall site to the processing terminal some 8km inland. At the landfall site the gas pipeline is routed in a ~5km underground tunnel underneath a bay. For operational reasons and planning consents as well as to mitigate environmental impact based on an environmental impact study, once the gas pipeline and the associated services and spares have been installed, the subsurface gas tunnel will be fully grouted. There will be no permanent access to the tunnel after construction is completed and the site compounds have been reinstated once works are complete. One of the key requirements is that “full grouting of the tunnel” is desired. The grouting material used is a non-Newtonian and thixotropic fluid mixture of bentonite, cement, plasticizer, retarder/stabilizer and water. The tunnel is filled progressively in 350m sections using a combination of existing and new pipework assuming the grout rheology will yield a fill slope of 1:100 in a 350m section. The proposed grouting system used one pump at the grouting compound to pump the grout into the tunnel using the existing tunneling pipework. For the longer runs a second booster pump was used in series to pump the grout to its final discharge location. The filling process is controlled via a system of flow meters, pressure transmitters and a tunnel CCTV system."

Jan 1, 2016

The major stages in the life cycle of a tailings facility include site selection, impoundment de-sign and construction, operation and closure. Optimum management of these stages requires an integration of all legal, engineering and environmental aspects in order to improve safety and minimize future potential risks for humans and the environment. This paper discusses the main factors involved at each stage and focuses on the stability considerations of the impoundment facility.

Jan 1, 2002

By Jeffrey C. Reid

Computer processing and high resolution graphics display of geochemical data were used to quickly, accurately, and efficiently obtain impor¬tant decision-making information for tin (cassiterite) exploration, Seward Peninsula, Alaska (USA). Primary geochemical dispersion patterns were determined for tin-bearing intrusive granite phases of Late Cretaceous age with exploration bedrock lithogeochemistry at the Kougarok tin prospect. Expensive diamond drilling footage was required to reach exploration objectives. Recogni¬tion of element distribution and dispersion patterns was useful in subsurface interpretation and correla¬tion, and to aid location of other holes. Tin was its own best pathfinder. Arsenic, also a useful pathfinder element, forms a discrete halo peripheral to tin mineralization. The arsenic halo is expressed in hand specimens by asenopyrite and/or scorodite staining.

Jan 1, 1989

By K. W. Morris

Of the fossil fuels used for power generation coal is by far the most variable and complex in its properties. A thorough review of the characteristics of the coal to be fired is essential before boiler design can begin. Major parameters such as heating value, moisture content and ash properties will determine not only the boiler size and configuration, but also the performance of the unit with respect to the thermal efficiency, particulate and gaseous emissions, and unit availability and reliability. An example of a review completed on a large low-rank coal deposit for a power plant will be described.

Jan 1, 1983

By Kadri Dagdelen

The definition and shortcomings of traditional cutoff grades are discussed. . The concept of optimum cutoff grade policy which maximizes the Net Present Value (NPV) of annual cash flows coming from a mining project is introduced within the basic framework outlined by K. F. Lane. Several examples are used to demonstrate the shortfalls of cutoff grade policies obtained by various heuristic optimization techniques. An algorithm to obtain an optimum cutoff grade policy which maximizes the NPV of a project is given and described in detail.

Jan 1, 1992

By Christopher Mark

Successful longwall gate entry design requires control of both vertical and horizontal stresses. Vertical, or overburden, stresses are most severe in the tailgate where they are concentrated by longwall panel extraction. Horizontal stresses, which are generally tectonic in origin, can be highly destructive during the development and headgate phases of longwall mining. The goal of this paper is to present the current state-of-the-art in detecting and controlling horizontal stresses. The information presented was collected through site investigations at 45 U.S. longwalls and an international literature review. The paper begins with a discussion of the present knowledge of regional in situ stress fields in the U.S. A review of available underground stress measurements from coal mines is presented, along with data collected by structural and petroleum geologists. The combined evidence indicates that a persistent ENE-EW trending stressfield is present throughout the eastern coalfields. Experience with horizontal stress in longwall mines is addressed next. The paper focuses on the northern Appalachian region, where the effects of horizontal stress have been most evident. Three case histories are discussed in detail, and the solutions each developed are highlighted. Observations made in the Southern Appalachian, Alabama, and Illinois coalfields are also described.

Jan 1, 1991

By R. L. Pearson

The 1987-88 Denver Brown Cloud Study was performed to determine the sources of the particle cloud which forms over Denver each winter. The study was organized under the leadership of Colorado Governor Roy Romer , EPA Region VIII and the Greater Denver Chamber of Commerce. The study was sponsored by over 40 organizations representing governmental agencies, the natural gas industry, the coal industry, utilities, oil companies, railroads, the motor vehicle industry, and other Denver area companies and organizations. The cost of the study was $1.5 million which was raised almost entirely from private sources. The study team was headed by Dr. John Watson of the Desert Research Institute of the University of Nevada. Dr. Watson is a recognized expert in conducting studies of this type.

Jan 1, 1990

By Verya Nasri, Scott Thorburn

The City of Toronto and the Toronto Transit Commission (TTC) have conducted an Individual Environmental Assessment (EA) for a 6.2 km, 4-station underground extension of the Spadina Subway from Downsview Station to Steeles Avenue. This Environmental Assessment Study was performed in three phases including routes and general station locations, alignments and station concepts and detailed assessment of the effects of the undertaking. URS Canada Inc. has led the consultant team for this Study. The anticipated total duration of the project is approximately 6 years and its estimated total cost is about $1.4 billion. This paper presents the planning process of the project, the environmental and engineering challenges, and the measures taken to address them.

Jan 1, 2007

By Nelson M. Solow

Raise boring of mine ventilation shafts in many cases offers a lower cost and higher speed method of construction in comparison to conventional shaft sinking. Where underground access is available for raise boring the potential savings indicate that raise boring should be considered as an alternative to other methods. Raise boring machines are currently in use which have the capability for reaming shafts up to twenty feet in diameter, depending on the strata and depth. These large capacity machines make it possible to consider raise bored shafts for moving large volumes of air. Although we will consider here only ventilation shafts, raise boring should also be considered for men and material shafts. When the mine planner has determined the volume of air required through a shaft at a particular location he is faced with the problem of selecting the shaft size. The principal factors in optimizing the shaft size are the construction costs for the shaft 'and the power cost to move the air through the shaft. The larger diameter the' shaft is the more it costs to construct, but for a given volume of air the power required (cost) becomes lower as the diameter increases. The construction cost is paid only once, when the shaft is constructed. The power costs, however, are paid throughout the life of the shaft. Methods of optimizing air shaft size found in the literature (References 1 and 2) amortize the construction cost and include it in the average annual cost of operating the airshaft. These methods derive a formula for the average annual cost vs. shaft size and de-rive the formula to compute the optimum size for a given air flow rate. It is, however, desirable to take into account tax considera-

Jan 1, 1977

By G. W. Ford, S. E. Black

Current research into coal based synthetic fuels is taking place on two fronts, fuels for power generation and conversion of coal to ultra-clean fuels for transportation. Present research into solid synthetic fuels is concentrated on development of clean coal technology which will meet or exceed the proposed cap and trade emissions set forth in the Clean Air Act Amendments of 1990. Research into ultra-clean liquid fuels is concentrated on either direct or indirect liquefaction process which could be used to manufacture both diesel fuels and gasoline.

Jan 1, 2003

By Nikhil Dhawan, Shrey Agrawal, Veeranjaneyulu Rayapudi

India’s steel vision of 2030 requires a huge amount of quality iron ore. The utilization of low-grade iron ores such as banded iron ores will play an important role to achieve the same production. The absence of alumina impurities in the banded hematite jasper (BHJ) ore provides it an edge over other low-grade iron ores. The conventional beneficiation techniques such as magnetic separation and washing were found to be ineffective to produce suitable feed (Fe ~ 60%) for the blast furnace. It was found that microwave exposure provides significant enrichment to the low-grade iron ore and can be used as a pretreatment step in the beneficiation of similar low-grade iron ores. The above study reveals that hematite phase is susceptible to microwave exposure which enhances the separation of iron values from impurities. Under optimum conditions, an iron-enriched concentrate with 61% Fe, 85% Fe recovery at 50% yield can be achieved from BHJ feed ~ 38% Fe. The pretreatment process for BHJ beneficiation includes only microwave exposure without any chemical additive and may prove economical and industrially feasible.

By R. R. Rollins

Conventional methods of controlling abandoned mine fires include: loading out, inundation, fire barriers, flushing, and surface sealing. This paper describes a proposed fire-control technique utilizing a new explosive fragmentation method. An impervious barrier is created by using explosive energy and strategic emplacement in boreholes drilled from the surface. Blast round design, average fragment size, and impermeability of the fragmentation barrier are discussed. This barrier, created by the blasted floor rock, could also be used to fill in the open space in abandoned mines for subsidence prevention or control.

Jan 1, 1989

By Luis Dr. Sobral

In this study, the removal of zinc, cadmium and copper from an aqueous sulphate solution, derived from the biomass desorption process, was examined by using a reaction system with a three-dimensional high surface area electrode (RNiF). This reaction system was found to be extremely effective in reducing metal concentrations to the ppb range. The effect of cathode potential and flow rate were studied for three different nickel foam porosities. In addition, current- potential curves were recorded, at a rotating vitreous carbon electrode, to deter- mine the possibility of depositing the aforementioned metals separately.

Jan 1, 1998

By C. E. Ekburg

Gold Quarry is a sediment-hosted, epithermal disseminated gold deposit located along the Carlin Trend. Gold, hosted by allochthonous Ordovician siltstones and cherts, is localized at the intersection of structures sympathetic to the major Good Hope and Gold Quarry faults. The magnitude of Gold Quarry was discovered in 1979 by surface exploration and by percussion holes drilled near the Maggie Creek orebody. Four years of development drilling delineated an open pit mineable gold deposit that contains 130 Mt (144 million st) of ore at an average 1.68 g/t (0.049 oz per st) of gold and includes a high-grade core of 46 Mt (51 million st) that average 2.64 g/t (0.077 oz per st) gold. Milling of the higher-grade portion began in 1985.

Jan 1, 1987

By A. Cordonnier, Ch. Obry, R. Evrard

In spite of the large annual expenditures and the vast field of activity covered, it cannot be said that many new grinding machines have actually come to light and modified the existing market for more than half a century. Manufacturers have mainly made advances in increasing machine sizes, efficiency and reliability, and in machine automation. The relatively recent emergence of roller presses is the only exception to this homogenisation of machine ranges. The development of roller presses in pregrinding has shown the advantages of compression grinding over the ball mill from the power consumption point of view. But classical roller presses still have maintenance problems due to the high grinding pressure. The FCB Research Centre has carried out much work in this field and in particular has studied the advantages of this process in pregrinding and integral grinding. These researches lead to the development of two new compression grinding machines. The first one, HOROMILL®, presented for the first time on the 8th European symposium on comminution at Stockholm, finds its application in the field of fine to very fine grinding in dry process. The second one, RHODAX®, presented at INTERMAT in Paris, covers the field of secondary and tertiary crushing and the first stage of grinding for most of the minerals in dry or wet process. Its high reduction factor permits to do with only one machine the work realised today with two or three crushing/milling stages. These two complementary machines offer a wide range of combination summarised on [Figure 1].

Jan 1, 1995

By Sun Guangzhong, Liang Jinhuo

Adverse geological condition is a major factor which makes construction difficulty in tunneling. But if it is predicted and tunnel support is made efficiently in time, the above difficulty can be reduced. It is necessary to develop one or several effective and economical geological methods for prediction of tunnel geology while expensive and time-consuming instruments are used. This paper reviews and proposes several geological methods for prediction of fault, seam, contact zone, and groundwater inrush. These methods have been proved to be effective and economical in tunneling practice in China.

Jan 1, 1987

By G. M. Ellis

This paper deals with some aspects of concrete construction in remote locations and/or cold climates. The writer's experience covers 25 years in construction in western and Central Canada. I will bring forth some pertinent observations and cost facts learned from this experience. Let us start by saying that there is nothing more important than preplanning the entire project. By this I mean the production of the engineering design, working drawings, soliciting of prices and ordering of all equipment and contractors work, the delivery of all equipment and all onsite work. All of this should be placed on a master schedule, preferably a C.P.M. We have been using C.P M. Scheduling for all of our work for 5 years and have found it in-valuable. This preliminary schedule will show initial items of work and target dates. After main equipment orders are placed and deliveries confirmed, the construction schedule can be revised to include manpower and construction equipment requirements. From this information the size of camp is determined. This, of course, must be ordered several months ahead. The manpower schedule can be broken into trades to tell us the number of men of each trade required at any time. This is important in helping to determine where the men must come from and whether or not any incentive is needed to get them. The schedule will also point out if it is impossible to get the project closed in before winter becomes too severe unless overtime is worked or the project is started in early spring. In most parts of Canada cold weather starts in October and lasts through April. A common term of reference has been to wait for the frost to come out of the ground before starting work in the spring. In some areas this can be as late as June. The construct-

Jan 1, 1971

Introduction Agrico Mining Co.'s Florida mining division has three surface mines and employs nearly 700 workers. The division produces some 6.3 Mt (7 million st) of phosphate rock annually. It is a good business. And Agrico has made it better by making it safer through a new approach to mine safety. In one year, Agrico - the second largest phosphate mining company in the US - recorded a stretch of one million manhours without an accident. That same year, the direct cost of accidents dropped to $9137 from a previous five-year average of about $50,000. Together with Don Roe, division manager of safety and security, Division General Manager Don Morrow made 1981 a watershed year for safety at Agrico. Morrow called on consultants from Safety Management Services of Du Pont's Specialty Services division to strengthen a safety program that was already better than average. From the late 1970s and into 1981, lost-workday cases (LWCs) were costing Agrico an estimated average of $22,000 each. And they were occurring with alarming frequency. In 1977, the company recorded six LWCs at an incidence rate of 0.64. This was followed by a jump to nine cases in 1978. In 1979, both occurrences and the rate increased - 10 LWCs at a 1.19 rate. The number of LWCs decreased to seven in 1980, with a rate of 0.71. Agrico instituted a far-reaching safety program in 1981, which began to take full effect in 1982. LWCs dropped from five in 1981, to three in 1982. And the direct cost plummeted from $110,346 to $28,828. In 1983, the mines recorded only one LWC. Its $9137 cost represented a reduction of $101,209 since the Safety Management Services of Du Pont had been called in. Through early 1984, the LWC incidence rate at the facility's three mines, phosphate drying plant, and transportation department was down to 0.26. This is 84% lower than the 1982 mining industry average, making it the safety leader among all Agrico companies, including its chemical plants. New Approach Agrico had the basics of a safety program in place when the Du Pont consultants arrived. But Du Pont suggested changes in responsibilities and company philosophy that formed the foundation of

Jan 1, 1985

By B. Waterman, R. Collins, V. R. K. Paruchuri, P. Gonzalez, H. Dijkman

"INTRODUCTION Mining and processing of sulfide ore bodies has the potential to solubilize sulfate. Gypsum in the host rock, as well as oxidation of sulfides during milling and processing can solubilize sulfate. Acid rock drainage (ARD) also has the potential to generate waters high in sulfate. Even after treatment of the ARD with lime, the treated water can have sulfate present in gypsum saturation levels. Most mine-sites reuse sulfate impacted water but as a mine nears closure, reuse options may be limited and water treatment becomes an option. Furthermore, sulfate discharge requirements, particularly for anti-degredation narrative standards, can be very strict. Freeport has investigated many new technologies to economically remove sulfate from these types of water. A Dutch company, Paques B.V. developed one of these technologies and it utilized biological reactors to convert sulfate into elemental sulfur in a 2-step process. In 1992 the first industrial reference of the SULFATEQTM technology was commissioned at the Nystar Budel zinc refinery in the Netherlands. PILOT PLANT TECHNOLOGY AND DESCRIPTION As shown in Figure 1, the plant contains several process steps, which can mainly be divided into the following sections: 1. Anaerobic biological system in which sulfate is reduced to hydrogen sulfide by sulfate reducing bacteria. 2. Aerobic biological system in which hydrogen sulfide is oxidized to elemental sulfur by sulfide oxidizing bacteria. 3. Solid/liquid separation in which sulfur, calcium carbonate and biomass solids are separated and dewatered. Sulfate impacted ground water is pumped to the feed water tank through a plate and frame heat exchanger to maintain the solution temperature around 95°F. A custom mix of micronutrients is dosed to the feed tank. This nutrient mixture provides essential elements for the growth of anaerobic and aerobic biomass. Urea is added to the feed tank and provides the required nitrogen source to the biomasses. The pretreated feed water is pumped into the anaerobic reactor. The reactor works on the gas lift principle. Sulfate reducing bacteria utilize hydrogen gas as electron donors and reduce sulfate to hydrogen sulfide. This reaction increases the alkalinity of the solution. Carbon dioxide gas is added in order to control the pH within working range of the reactor. Due to the low solubility of the hydrogen gas, the anaerobic gas mixture is recycled through the system. The gas mixture recycle also provides the gas lift for mixing within the anaerobic reactor."

Jan 1, 2016

By Carmel Bofinger, Maureen E. Hassall, David Cliff, Eric Stemn

Incident investigation is of utmost importance in most high-risk industries and is often used to improve organisational safety. This study was undertaken to examine the content of past incident investigation reports to determine the effectiveness of the incident investigations. The study uses a semi-quantitative method to assess the effectiveness of incident investigations in the Ghanaian mining industry by evaluating the quality of past investigation reports. The assessment tool consists of five elements with several indicators and rating scales for assessing the quality of an investigation report as a measure of the effectiveness of the investigation. The method was applied to 304 investigation reports of three Ghanaian large-scale gold mines, and the results correlated with incidence rates of the mines to determine if any relationship existed. The results showed that the mines differ significantly in the quality of their investigation reports, suggesting differences in the effectiveness of their investigations. In addition, the incidence rates of the mines negatively correlated with some elements of the assessment tool. In general, the method was found useful and revealed areas where improvement is needed.