Search Documents

By J. A. Boyle

In the Frick District of U, So Steel Corporation, we have had more than 37 years of experience in the use of multiple-fan ventilation systems, in our coal mines. In our Colonial field, with a long belt installation, we have mined 85 million tons of coal with the use of the multiple fan system of ventilation. In our Palmer field, with the use of the same arrangement, we have mined 90 million tons of coal--a total of 175 million tons without one accident attributable to improper mine ventilation. The same system, fundamentally, has been installed in our expanding Robena operations and at its present stage of development we are using eight fans to ventilate this area. To date we have mined 55 million tons of coal with very encouraging results and again without any accidents attributable to ventilation.

Jan 1, 1961

By Robert M. St. Louis, Janet M. Edgecombe

The Mercur Mine's autoclave is an alkaline pressure oxidation system, operating at 220°(428°F) and 3061 kPa (444 psig) (total). Up to 725 metric tons (800 st) of ore, grading 2.02 g per mt (0.059 oz/st) Au and containing 1 to 2% sulfide sulfur, are treated daily in this circuit. A mineralogical and chemical investigation was initiated to locate the cause of lower than anticipated gold recoveries. Greater than 70 wt. % of reduced sulfur is oxidized; therefore, the autoclave is operating at specification. The low recoveries were attributed to increased concentrations of organic carbon in refractory ore. Activated carbon concentration in the attached CIL circuit was increased from 15 to 40 g per 1, leach temperature held below 21°C (70°F), and carbon flow changed to counterflow. These measures resulted in gold recovery improving from 75 to 82%.

Jan 1, 1990

By Pierre Filiatreault, Brian Straight, Stephanie Thibeault, Devin Castendyk, Londie Cameron

"Working on or near water at active, closed or abandoned mine sites is inherently dangerous. Between 1996 and 1999, the U.S. Mine Safety and Health Administration (MSHA) reported 17 fatalities involving drowning at U.S. metal, non metal and coal mines (MSHA, 2000). Openpit mines which fill with water following mine closure, called pit lakes, present numerous risks to environmental monitoring teams including: a) drowning, b) hypothermia, c) falls to the ground from the top of high walls, d) collapse of unstable access roads, e) rock falls and avalanches from pit walls, f) avalanchegenerated tsunamis traveling across the lake surface and g) rapid degassing events.Some pit lakes are simply not safely or easily accessible for ongoing monitoring. However, the routine collection of water samples from the entire water column on a regular basis is needed to monitor the evolution of water quality over time, verify the accuracy of numerical predictions and, ultimately, manage lake water chemistry and ecological risks. For pit lakes with surface water discharge, regular monitoring is used to appropriately design and adjust water treatment plants in order to produce acceptable site discharge water quality.As a product of these risks and the need for water samples, mining companies spend considerable expense on pit lake safety as part of monitoring programs. This includes training personnel for on water duties and hazards, purchasing or hiring specialized equipment and personnel (such as boats, boat operators, personal floatation devices and cold-water clothing called mustang suits), stabilizing pit walls and maintaining safe access roads to the lake surface and employing spotters who can directly communicate with emergency medical services to watch sampling activities because cell phones and radio signals can be blocked by pit walls. Some sites utilize redundancy to prepare for unexpected incidents and accidents. For example, one Canadian mining company requires two boats on the water during pit lake sampling events, with a third boat on the shoreline, gassed and ready to go. In addition, water samplers are required to hold Marine Emergency Duties training to ensure the entire boat crew is sufficient and competent for the safe operation of the vessel in the event of an accident."

Jan 7, 2017

By Randall E. Brown

Irrigation simulates a climate change so that crops can be grown that otherwise would not thrive. The abundant sunshine and warm weather of many arid regions induces a rate of growth in excess of that in cooler, moister regions. Hence, the arid part of eastern Washington, traversed by the Columbia River, is admirably suited to irrigation. The Pasco Basin lies in south-central Washington at the south end of the Columbia Basin Irrigation Project of the U.S. Bureau of Reclamation. The Basin, because it lies in the rain shadow of the Cascade Mountains, receives only 6 to 10 inches of precipitation a year with somewhat greater amounts, commonly as snow, on the higher hills. Recent extremes included 3 inches of precipitation from August 1967 to August 1968, and 12 inches in the succeeding "12 months. Most of the precipitation falls during winter. If it were to fall in summer or were evenly distributed throughout the year, evaporation rates probably would produce a true desert.

Jan 1, 1971

By H. Walqui, S. K. Kawatra, C. H. N. Jeltema, T. C. Eisele

"The literature contains many cases where the shape of hydrocyclone efficiency curves vary from the ideal “S” shape. These often appear as changes in slope, or inflections. These inflections can be divided into two categories: “coarse” inflections, which are caused by differences in the density of the minerals being separated, and “fine” inflections, for which there are a number of competing hypotheses concerning their cause. The existing literature addresses either the fine inflection or the coarse inflection, but no studies have reported both types of inflection occurring at once in a single hydrocyclone test. This paper presents hydrocyclone results from both in-plant studies and laboratory experiments that show both coarse and fine inflections. The industrial significance of both types of inflections is discussed. Hydrocyclone efficiency curves show the probability of any given particle reporting to the hydrocyclone underflow as a function of its size. Selectivity functions, S(d), are used to represent the fraction of the feed material in size fraction “d” that reports to the hydrocyclone underflow. Plotting this selectivity function against particle size leads to the standard S-shaped efficiency curve shown in Fig. 1. In the “uncorrected” curve, the tail of the curve does not go through 0%, because a portion of the solids are bypassing classification. This happens as a result of their being carried along by the water, and is most important for the finest particles. The curve can be “corrected” based on the fraction of the feed water that reports to the underflow, represented by the bypass fraction, Rf. The corrected curve then normally passes through 0%, as shown in Fig. 1.The act of correcting the curve shifts the value of the d50 size, which is the size that has an equal probability of reporting to either the overflow or to the underflow. Correcting the curve to account for the bypass fraction makes it easier to compare cyclone performance under conditions that cause the quantity of water in the underflow to change, but that do not alter the actual corrected cut size (d50c).The corrected efficiency curve can be expressed closely by equations such as Plitt (1976):"

Jan 1, 2015

By Klados. T.

MSC.Software assessed the performance of the drive end and non-drive end bearings on a ball mill using the finite element method. The assessment included the effect of mill and pedestal deformation on the performance of the bearings. Oil film thickness, oil pressure distribution and power requirement were of interest. A solution approach coupling a structural solver to a Reynolds equation solver was specifically developed for the project. Results showed that the deformation of the bearing surfaces had a significant influence on the performance of the bearings. For example, for the non-drive end bearing, the minimum oil film thickness computed for the deformable bearing surfaces was significantly lower than calculated for the non-deformable case. The results also showed that cavitation was likely in both the drive end and non-drive end bearings (severe negative pressures were obtained in both bearings). Other design variations were also assessed, e.g. a case with a modified radial clearance which improved the results.

Jan 1, 2006

By Gary F. Rajala, Bruce R. Greenwood

INTRODUCTION The Empire Mine is an iron ore mining, concentrating and pelletizing facility operated by The Cleveland-Cliffs Iron Company in the Upper Peninsula of Michigan. Owners of the mine are Inland Steel, LTV Steel, Wheeling-Pittsburgh Steel and Cleveland-Cliff s. The orebody is a fine-grained, low grade iron formation with magnetite as the primary constituent. Also present are iron carbonates, iron silicates, chert, hematite, goethite and quartz. The original six concentrating lines were started in late 1963. Successive expansions of ten lines in 1967, five lines in 1974 and 3 lines in 1979 have resulted in Empire reaching a present annual capacity of 8.0 million long tons of pellets. The Empire flowsheet was developed over several years of laboratory bench testing, pilot plant testing and testing of a full-scale primary autogenous grinding circuit. Since the original flowsheet was established, modifications have been made based on pilot plant and full-scale plant tests. The present flowsheet for three sections of the concentrator consists of one stage of crushing, two stages of closed circuit autogenous grinding, two stages of magnetic separation, one stage of hydraulic concentration and two stages of flotation (rougher and scavenger). The flowsheet for the fourth section of the concentrator (Empire 4) is the same as the first three sections, except a crusher has been added to crush excess pebbles. The Empire 4 flowsheet appears in the at- tached figure. PRIMARY GRINDING CIRCUIT FLOWSHEET Empire has a total of 24 individual grinding lines. However, at the present time, Line 1 is not being used for processing crude ore. The primary mill on Line 1 is now grinding flux stone for fluxed pellet production and the secondary mill is being used as a ball mill to grind rougher flotation tailings prior to a scavenger flotation circuit.

Jan 1, 1992

By R. M. Imhof, M. J. G. Battersby, J. V. Brown

There is a plethora of former industrial sites where coal mining operations have left large slurry impoundments. These contain raw washed fines, which have previously been too expensive to process to requisite grades for commercial use. New technology has been developed for fine material processing, namely the Imhoflot pneumatic flotation G-Cell. This froth flotation technique is a highly efficient means of concentrating coal and is particularly appropriate to the nature of materials encountered in tailings ponds. The high volumetric throughput resulting from the vastly reduced residence time in the cell allows for drastically reduced equipment sizes when compared to conventional flotation cells. This means the process, when combined with innovative pre treatment and filtration equipment can be developed as a mobile plant concept. This is seen as a minimum requirement when re-treating and rehabilitating fine coal ponds.

Jan 1, 2003

The Northside Storage Tunnel Project in Sydney includes over 20 km of TBM driven tunnels, over three km of declines and major caverns and pump rooms. The paper describes methods used for design on the project. Emphasis is given to the refinement of the use of empirical rock mass classifications, and to the use of discontinuum numerical methods. The use of empirical rock mass classifications in Sydney sandstone has usually led to conservative design because the systems are based on a random orientation of joints in the rockmass. Because the joint sets are usually oriented in a way that is beneficial for tunnelling, limits must be placed on the parameters used in the classifications system. The paper discusses these limits and the derivation of the parameters. The use of numerical methods in Sydney sandstone is discussed. Continuum methods have their uses, but discontinuum methods are preferred. The use of UDEC has been validated against a previous project, the New Southern Railway. Recommendations are given for UDEC models. In Sydney's geology, so advantageous for tunnelling, the challenges of this project have been to make the best use of the good conditions, while maintaining safety for the workforce and the future operators of the project.

Jan 1, 1999

By T. A. Marcotte, D. J. Bobrow, S. Vaghar

This paper discusses the geotechnical instrumentation program on the Central Artery/Tunnel Project, in Boston, Massachusetts. Particular attention is given to a state of the art Graphic Information System (GIS) application which has been developed for rapid analyses and reporting of data. This application will see extensive use during the ongoing complex downtown tunnel construction. The excavations in soft ground require cuts of up to 120 feet deep and 250 feet wide. Deformation and groundwater monitoring instruments have been installed to monitor the stability of the excavation support systems and the abutting buildings. The use of this application is illustrated with an example from an ongoing contract.

Jan 1, 1997

By A. Haghighat

A risk analysis on mine fires for all U.S. underground coal mines from 2000–2012 was completed to identify locations that have a high risk for fire incidents. The data for this analysis was extracted from the Mine Safety and Health Administration’s (MSHA) mine fire accident reports database. After identifying fire incidents from this database, a risk matrix was developed for underground locations that showed a significant propensity for fire incidents. This matrix associates the hazards and risks with the severity and frequency of their consequences at each location. These significant mine areas will be the concentration of future studies in fire behavior, suppression techniques, and simulation methodologies. INTRODUCTION Fires in underground mines pose significant hazards to personnel because of inherent restrictions to movement and limitations to egress routes. Despite improvements, mine fires remain serious hazards in underground coal mine. In order to better mitigate the risks from fire hazards in the modern underground mining environment, a better understanding of where fire events occur must be gained. The following paper presents an investigation on the number of fatal and non-fatal incidents in underground coal mines fires from 2000 to 2012. Three phases of risk assessment (i.e., risk identification, estimation, and evaluation) were applied to the recorded fire events from the MSHA incident database that occurred during this time period. Using this process, a fire hazard was first defined. This definition was then used to identify any incidents that had occurred as a result of the defined hazards. The seriousness of the injuries and damages were finally quantified for each incident though an estimate of severity and frequency and then aggregated according to underground location (ISO, 1999; Van Duijne, 2008). Using this approach, locations prone to incidents resulting from fire hazards were first identified. The risk for the occurrence a fire incident in general was then estimated for each of the identified locations. The results of this assessment will be used to improve fire simulation techniques for the identified, high risk underground locations. RISK IDENTIFICATION A risk for this assessment was defined as any single occurrence of a fire initiated by the ignition of gas, dust, or electricity. Each recorded occurrence of such an event in the MSHA incident database was counted as a single fire incident. Both non-fatal incidents that were reportable but did not result in a fatality and fatal incidents that fell into the aforementioned criteria were counted. Incidents in the MSHA database that were already classified as “generic” were not considered. The remaining incidents were then totaled and aggregated according to the underground location in which they occurred. In previous studies, a number of locations, which are listed in Table 1, were highlighted as high fire hazard areas (McDonald et al, 1980; Pomroy et al, 1995; De Rosa, 2004). These locations were used to group the fire incidents extracted from the MSHA incident database. The compiled numbers of non-fatal and fatal underground coal fire incidents from 2000 to 2012 are displayed in Table 1.

Jan 1, 2019

By John C. Cook

There is pressing need for better means of exploring ground conditions ahead of mining. Exploration drilling has the drawbacks of high cost and a seriously restricted sampling zone. Traditional geophysical exploration methods including gravity, magnetic and resistivity techniques have been used with some success underground, but all give poor target delineation relative to range, since they depend upon minor distortions of a potential force field. Much greater ratios of resolution to range can, in principle, be obtained by employing electromagnetic or seismic radiation as the exploring agent. This is because propagation time delays can be used to measure range accurately, and to separate the small effect of a distant target from the much larger effects of nearer targets and of the transmitter. Seismic waves have long been used with great success in exploration for petroleum, and recent research on their application underground is promising. Electromagnetic (radar) waves have been very successfully used for detection and location through the air and outer space, and have also explored through polar icecaps more than a mile thick.l It is not generally realized that below the soil many rocks are also somewhat radar-transparent, and that radar can be used for exploring such rocks, once a quarry, a mine, a borehole, or other means of access has been opened. Radar waves are reflected by any boundary or object where they encounter a large change in electrical properties.2 The usual cause of such a change is a difference in moisture content. Radar waves passing

Jan 1, 1972

The structure of a mine ventilation network (M.V.N.) can be represented graphically using either the mine plan (map) itself or a number of other types of diagrams. In the U.S., the two most common approaches are the line and the schematic diagrams (see Figures 1 and 2). The purpose of this paper is to introduce another type of diagram, called the canonical diagram (6). The method of M.V.N. representation which uses canonical diagrams is used extensively in Europe, and especially in Poland, where it was developed. The canonical diagram is a noncalibrated topological image of a ventilation system. It gives a simple representation of the ventilation network, allows for the classification of currents within it and enables rapid computer analysis and computation, as well as the representation of the results. It is especially useful in studying and controlling the air flow, and it may be a life saving tool in conducting rescue operations during and after mine fires.

Jan 1, 1986

By Charles E. Weaver

A core from the La Camelia attapulgite mine in north Florida was studied in detail to determine the detailed vertical variability and the relations of the various parameters. The structural, textural, mineralogical and chemical data indicate there are two major depositional cycles represented within the minable interval. The sediments deposited during the two cycle differ in detail but in general are similar. The environments of deposition grade from shallow marine to lagoonal to tidal flat to marsh. The sedimentary structure (lamination, burrows, pebble conglomerate), mineralogy (attapulgite, montmorillonite, sepiolite, dolomite, calcite) chemistry (Al, Mg, Fe) are closely related to each other and their nature is determined by the depositional environments. Most of the clay minerals and carbonate minerals are authigenic and are therefore particularly sensitive to environmental differences. The variability and environmental features seen in this core are characteristic of the sediments in the general attapulgite mining area. A detailed understanding of the relationships discussed should be of value in prospecting, mining and processing.

Jan 1, 1972

By Z. Eisenstein, H. K. Heinz, F. M. Kuwajima

Due to its complex rheological behaviour, shotcrete induces a ground-structure interaction that differs significantly from other types of tunnel linings. For the same reason, the instrumentation of shotcrete linings presents special problems, particularly when it comes to estimating the stresses transferred to the lining during construction. The shotcrete characteristics which affect the stress distribution are initially discussed. Measurements obtained in a recent soft ground tunnel are also presented. The conclusions are aimed at introducing practical recommendations for the design of tunnels where shotcrete is used as initial and/or final support.

Jan 1, 1991

By Frederick T. Graybeal

Silver Bell is located about 56 km (35 miles) northwest of Tucson, AZ. It is a classic porphyry copper deposit containing enriched disseminated chalcocite ore in altered porphyritic rocks with chalcopyrite in adjacent skarn zones. The discovery of Silver Bell was an evolutionary process that occurred over a 75-year period. Recorded mining activity began about 1865 on Boot Hill east of El Tiro pit (see Fig. 1) where outcrops of altered limestones were found to contain 425 to 482 g (15 to 17 oz) Ag mixed with copper oxides. By 1874, the Young America Copper Co. was mining shallow occurrences of 30% Cu along the north side of the present Oxide pit. The ore was shipped by wagon to Yuma, AZ, and then by boat to San Francisco for smelting. By 1881, the district supported several mining companies, two small smelters, and was being favorably compared to Bisbee in local newspapers. Most of the ore mined in the period 1865-1903 came from pods of massive sulfide or their oxidized products which were distributed in an unpredictable fashion through a large skarn zone in Paleozoic limestone east of El Tiro pit. Ore grades varied from 5 to 10% Cu.

Jan 1, 1991

By Francis R. McAllister

SYSTEM ENGINEERING Years ago, while attending Harvard's Advanced Management Program, Professor Robert Hayes introduced our class to the, then not-so-familiar, concept of systems engineering. First assignment-dinner at The Benihana of Tokyo Restaurant! Delighted, but a bit mystified with the assignment; we had dinner at Benihana. Back in class, Professor Hayes inquired about the assignment and persuaded us; that Rocky Aoki's business formula for Benihana was not necessarily Japanese cuisine, but rather the systematic way in which he moves more people-if you will, processes more people through his restaurants than his competition, by systematically linking all restaurant functions. For instance, the bar is a holding area in which patrons ideally wait no more, or no less, than 20 minutes. When seated, your table, which accommodates eight, is filled with eight even if you are a party of two. The Japanese chef is also the entertainment, and when, at the end, he cleans the grill, you are being subtly prompted that dinner is over. The bill accompanies ice cream, systematically delivered shortly thereafter. You are expected to pay promptly and depart, as there are eight more, mostly unacquainted, people who have waited 20 minutes in the bar, and who are assembled ready to be seated at your table. For me-this was electrifying. I understood the concept, concluded it was very powerful and felt prepared to conquer whatever, by means of its application. That was years ago and I can safely say I have yet to fully realize on the euphoria of that moment. Why? Well, I simply conclude: • The concept of systems engineering is simple and not revolutionary, but The application of systems engineering is far from simple and is revolutionary.

Jan 1, 2004

By D. A. Bird

Geochemical models using published thermo-dynamic data and laboratory derived kinetic rate laws allow prediction of post-closure pit lake geochemistry at open pit mining sites. A combination of "forward" and "inverse" modeling techniques can predict the pit lake geochemical evolution from initial infilling to eventual steady state attained decades or centuries after closure. Computer codes have been developed to model chemical reactions such as pyrite dissolution, describe the ground-water flow regime, and provide rock-water ratios. The incorporation of site specific information, such as ultimate pit dimensions, geologic and hydrologic data, acid generating potential (AGP) vs. acid neutralizing potential (ANP), and laboratory derived kinetic rates, allows application of the model to open pit mines at any stage of development.

Jan 1, 1994

By G. Deissman, S. Kistinger

For the last 15 years environmental Life-Cycle Assessments (LCA) have increasingly been used to evaluate the environmental performance of industrial processes and products and have been employed as a basis in decision making processes in the public and industrial sector. However, assessment methodologies for environmental protection measures and reclamation/remediation measures with respect to their consumption of natural resources are generally poorly developed. In this presentation a methodology for LCA of environmental protection measures and remedial actions, respectively is suggested, using the remediation/reclamation of mining sites as an example. Key aspect of this approach is the development of an evaluation method appropriate for environmental protection measures, which links the various impact indicators recognised in the impact assessments and allows their integrated assessment.

Jan 1, 2005

By Zhenqi Cai

The ongoing Overpeck Valley Parallel Sewer Project of Bergen County Utilities Authority (BCUA), New Jersey, is a US $65 million CSO improvement program to meet a State DEP consent order by 2010. One major program component includes a total of 1.8 km (1.2 mile) long, 1,800 mm (72 in) diameter reinforced concrete pipe (RCP) installed by a Herrenknecht AVND1800AB MTBM. The alignment includes drives through 850 m (2,788 ft) of extremely soft glaciolacustrine varved clay, 980 m (3,214 ft) of loose to medium dense mixed soils containing silty sands, gravels, and boulders, and crosses under the New Jersey Turnpike, US Highway Route 46, and a CSX Railroad Intermodal Yard and a branch mainline. Two types of MTBM cutterheads are being used, one configured for the weak varved clay, and one for the mixed soil conditions. The MTBM is also equipped with a double-steering system consisting of a standard front steering joint and a second trailing steering joint to assist grade control should adequate steering not be achieved by the front primary steering in extremely weak soil conditions. This paper discusses the significant engineering aspects and challenges related to site settings, ground characterization, key MTBM features and performance, and required ground treatment.