Search Documents

By R. E. Brewer

Phelps Dodge Mining Company (Phelps Dodge) is operating a pressure leach vessel (PLV) for copper concentrates at the Bagdad Mine facility in Arizona. This single PLV unit was engineered and constructed based on continuous laboratory testing, reaction chemistry and kinetics, and available pressure vessel technology. The challenge of designing for optimum process retention time, agitation, oxygen mass transfer, temperature and pressure will be reviewed in this paper. The PLV interior lining, agitation equipment and compartment configuration chosen for the PLV will also be reviewed.

Jan 1, 2004

By T. V. Ramey

Heap leaching in certain parts of the world, such as Chile's Atacama Desert, brings unique design problems in the form of possible large differential settlements of the foundation soils due to the dissolution of salts in northern Chile the soils often contain very high concentrations of soluble salts (nitrates, potassium, magnesium, and common sodium). When a leak in the liner occurs, the escaping solution dissolves these salts and triggers differential settlement. If the settlement is great enough, the geo-membrane tears, the leakage increases, triggering more differential settlement. The nitrate plants have experienced many occurrences of this phenomenon where a brine pond will undergo a sudden and complete loss of the impounded liquors. The authors present a simplified technique to quantify the differential settlement resulting from dissolution and provide a method which can be used to select a geo-membrane with suitable flexibility under axi-symmetric (multi-axial) load conditions to tolerate the predicted settlement. (This paper was previously published for Randol Gold Forum 1996 [Ref. 6]).

Jan 1, 1997

By R. E. Musgrove

At the present time Climax Uranium Company recovers vanadium oxide from carnotite type uranium ores in the mill at Grand Junction, Colorado, The flowsheet of this mill is shown in Figure I. Vanadium is solubilized by a salt roast of the slime fraction of the ore and dissolution is accomplished by a water leach. The metal is precipitated from the pregnant liquor as sodium polyvanadate by heating to boiling and adjusting the pH to 3 with sulfuric acid. The sodium polyvanadate, commonly called, "red caken, is filtered, melted, and cast into thin flakes. This fused flaked vanadium oxide is the material which is packaged for sale. Fused vanadium oxide, marketed by Climax, contains approximately 87% V205, 7% alkali oxide, 0.08% sulfur, 0.03% phosphorus, and less than 0.5% Insoluble. This material is of a lower grade and has a higher alkali oxide content than other vanadium products offered for sale at this time. A typical analysis of a high grade vanadium oxide currently offered for sale by another company is 98% V205, 1 - 2% alkali oxide, less than 0.05% sulfur and less than 0.2% Insoluble. The only reagent consumed in the precipitation of the sodium polyvanadate is sulphuric acid. The total reagent cost is 0.58 cents per pound of vanadium oxide produced.

Jan 1, 1958

By Wen Tao Liu, Tong Tian, Fu Sheng Niu, Xiu Man Liang

In order to address the difficulty of accurate segmentation of froth images of different sizes, a method of froth image segmentation based on highlight correction and parameter adaptation is proposed. First, a machine vision system on a single-cell flotation machine is built to collect froth images. Homomorphic filtering is used to improve the uneven brightness and shadow of the images. Fuzzy c-means (FCM) clustering is then utilized to classify similar highlights that belong to the same froth. After Otsu threshold segmentation, a parameter-adaptive morphological operation is used to extract the marker points and edge bands and correct the froth edges in the original image. Finally, the modified image is filtered by morphological reconstruction, and the highlight mark is used as the local minimum point for watershed segmentation. Three sizes of froth images are segmented in comparative experiments. The results show that the proposed method is suitable for the segmentation of froth images of different sizes. The position of the extracted segmentation line is close to reality, with average over-segmentation and under-segmentation rates for froth images of 2.6% and 6.8%, respectively. The froth image segmentation performance is stronger than that of the other methods examined.

The Barrick Zaldivar mine is an openpit, heap-leach copper mine in Region II of northern Chile at an elevation of 3,300 m (10,826 ft), approximately 1,400 km (870 miles) north of Santiago and 175 km (109 miles) southeast of the port city of Antofagasta. In 2006, Zaldívar produced 307 million lbs of copper, with reserves estimated at 5.7 billion lbs. The mine uses conventional methods of openpit mining: Pure cathode copper is produced by three stages of crushing and stacking the ore, followed by heap leaching and bacterial activity to extract copper from the ore into solution. A solvent extraction and electrowinning process then removes the copper from solution and produces the cathode copper. A flotation plant also recovers copper contained in the fine fraction of the crushed ore. In 2006, an existing A-frame structure that covered copper ore from the mine?s secondary crushing operation was damaged beyond repair. The material delivery configuration of this original structure had the conveyor carrying incoming ore directly over the low roof to drop ore into the building at its peak, and ore trickling from the sides of the conveyor had accumulated on the roof, overloading it. A better solution had to be found, and fast: First, the Chilean Commission does not permit uncovered piles of this type since the extremely fine material leads to serious pollution problems. Second, Barrick Zaldivar is very concerned about worker safety, and the amount of dust created by the uncovered pile was not acceptable. Finally, some amount of copper was lost in the dust generated by the winds of the Andes. The major issues faced by Barrick Zaldivar in designing a new structure included:

Jan 1, 2009

By Z. J. Hladysz

A Deep Underground Science and Engineering Laboratory (DUSEL) is being planned at the site of the former Homestake Gold Mine in Lead, South Dakota, under the sponsorship of the National Science Foundation (NSF) in cooperation with the Department of Energy (DOE). This national facility will host a variety of multi-disciplinary science and engineering experiments including physics experiments that require shielding from cosmogenic radiation. Current plans include construction of large rooms (up to 55 m in width) at depths of 1.48 km (4850 ft) and 2.25 km (7400 ft) below the surface. Preparation of the preliminary design required the development of a geotechnical characterization program including: preliminary drilling and coring, core logging, drill hole mapping with a televiewer, drift mapping of the geology and rock structure, in-situ stress measurements, and laboratory testing of the mechanical properties of the rocks and discontinuities. Overall rock quality is very good to excellent. Site investigations were followed by geotechnical assessments for the construction of caverns and laboratory modules. The results are favorable and reaffirm selection of the Homestake site for establishment of a Deep Underground Engineering and Science Laboratory.

Jan 1, 2011

By E. V. Manlapig, B. K. Gorain, N. W. Johnson, K. Ward

A flotation model developed at the Julius Kruttschnitt Mineral Research Centre was used to predict the performance of copper rougher and scavenger circuits at the copper concentrator at Mount Isa Mines. The model describes the kinetic response of an ore in a flotation cell in terms of ore floatability, cell characteristics and froth recovery. The floatability parameters of the rougher feed ore were obtained directly from a detailed plant survey. Flotation analysis was carried out for twenty different size-by-liberation classes to account for the effects of particle size and liberation on flotation. This paper investigates the capability of the model to predict the flotation behavior of 20 different size-by liberation classes in the rougher and the scavenger banks.

Jan 1, 2000

The General Purpose Simulation System (GPSS) is a computer simulation language that has been used for simulations of open pit haulage operations since the 60's. It is easy to learn, simple to use, and has a block-diagram structure that is amenable to load-haul systems. However, due to its lack of flexibility, there are situations where another language should be chosen. This paper reviews the characteristics and capabilities of both GPSS and FORTFAN with regard to open pit shovel and truck simulation. The relative advantages and disadvantages are highlighted and a case study presented along with comparative results from two computer models (one written in GPSS and the other written in FORTRAN).

Jan 1, 1986

By Steven W. Hunt, Ronald E. Heuer, Safdar A. Gill

A 3.3 m (11 feet) diameter, 51 m (168 feet) deep temporary steel casing which had been sunk within glacial soils buckled and collapsed on July 29, 1985. The collapse occurred at the CT-8 Dropshaft site in Milwaukee while two workmen were contact grouting outside the casing in an attempt to stop groundwater inflows through a bottom plug. This paper describes the soil and groundwater conditions at the site, the casing design, the method of shaft construction, and probable causes of the buckling failure. Specific aspects of the paper include: slurry method of shaft excavation and casing installation, soil creep, earth pressure due to three dimensional arching, and buckling strength of a casing surrounded by slurry rather than grout and firm soil. The paper should be of interest to designers and constructors of temporary ground support systems for deep shafts.

Jan 1, 1995

By R. Schuerch, G. Anagnostou, R. Poggiati

"The paper presents dimensionless design diagrams for estimating the stand-up time of a tunnel face in saturated ground of medium-low permeability. The diagrams cover a wide range of ground parameters and apply to shallow tunnels (overburden less than two diameters). As the time-dependency of the face stability in water-bearing ground is associated with the consolidation process in the soil ahead of the tunnel face, the stand-up time is determined by means of hydraulic-mechanical coupled spatial stress analyses. The results presented are important for tunnel engineering practice, e.g. when estimating the feasibility of atmospheric interventions in the working chamber of a closed shield. INTRODUCTION The response of water-bearing medium-low permeability ground to tunnel excavation is time dependent. The time-dependency is due to a transient seepage flow process that is triggered by the excavation and develops slowly over the course of time. Experience shows that the short-term behavior the ground is more favorable than the long-term one: the deformations increase with time; the tunnel face may be stable initially and fail only after some time. The time over which the tunnel face remains stable is called the stand-up time. This paper investigates the time dependency of the tunnel face stability assuming that all time effects are due to consolidation rather than creep. This assumption is reasonable for shallow tunnels crossing water-bearing soils. In the problem under analysis, the unsupported tunnel face remains stable under the undrained conditions prevailing after excavation, but collapses before reaching the drained conditions prevailing at a steady state. The assessment of the stand-up time is important from an economical point of view for both mechanized and conventional tunneling through weak water-bearing ground, as a long stand-up time removes the need for face support or ground improvement works during standstills, thus saving time and money, while short stand-up times require hyperbaric interventions or the implementation of costly and time-consuming auxiliary measures."

Jan 1, 2016

By Lawrence Lien

The reduced need for traditionally trained and educated personnel in the mining industry is systemic to the changing mining industry. Universities and other training institutions are meeting the traditional skill needs required by the industry, but are the skill needs going to be the same in the near future? The answer may be no. Mining is changing because of increased liabilities and costs of environmental and safety is-sues; lower grades of minerals in traditional mining activities and the advent of new bio-chemical processes and robotic equipment. More productive and economic alternatives, and larger, more sophisticated and automatic equipment, are also changing the industry. Engineering is more specific, accurate, precise and expensive. Measurement is more thorough and timely of progress, production, costs and productivity. And, the industry will likely be engaging in more undersea mining, possibly space-based processing, less human interaction and more remote control of events than was previously thought possible.

Jan 1, 2011

By Paul M. Jr. Musgrove, Donald C. Moore

Conventional Smelting Practice Conventional copper smelting practice varies from smelter to smel¬ter, but generally consists of some or all of the following unit processes: roasting, smelting, converting, and fire refining. Roasting. Copper sulfide concentrates can be smelted directly or after an initial roasting step. Roasting is used in some smelters because roasting prior to smelting increases smelting capacity, less energy is required to melt hot roaster calcines than wet sulfide concen¬trates, roaster off gases are high in Sot concentration, 5-15% SO2, and some volatile impurities are removed from the concentrate prior to smelting. However, many smelters do not use roasters, because the problems associated with handling hot dry calcines outweigh the advantages mentioned. Concentrate roasting is performed in multiple hearth or fluid bed roasters. If the moisture is low, roasting can be performed autogenously, usually at 500-600°C. High roasting temperatures are avoided because excess oxidation of the iron compounds may lead to magnetite formation. Magnetite is detrimental to reverb operation because mag¬netite can combine with refractory minerals to form a highly viscous slag. This slag prohibits efficient matte-slag separation and leads to excessive copper losses. Also, magnetite can settle through the matte layer, deposit on the furnace bottom, and consequently reduce furnace capacity. Roasting is carried out only on sulfide concentrates prior to smelt¬ing in reverb or electric furnaces. For smelting processes, such as the flash and continuous that rely on the exothermic heat of oxidation of the sulfur minerals, roasting is not practiced. Reverberatory Smelting. The predominate copper smelting fur¬nace for the past 50 years has been the reverb. These furnaces are typically 100-120 ft long, 30-35 ft wide, and 12-15 ft high. A typical furnace layout is shown in Fig. 2. Refractory brick linings cover all internal surfaces of the furnace. Originally the flame was directed to reverberate or reflect off the furnace ceiling and melt the feed material. Current practice is to direct the flame down the furnace length to melt the concentrate. A method of charging the concentrates or calcines, generally along the side walls to minimize refractory erosion, is incorporated in the furnace design. The copper concentrates, calcines, and fluxes charged into the reverb undergo a series of complicated reactions as the temperature of the mixture increases. The reaction of the iron and copper sulfides with the oxygen in the furnace produces a molten Cu25-FeS mixture called matte. Copper smelting metallurgy is based on the fact that sulfur has a greater affinity for copper than for iron and most other common metals. Therefore, in a system containing copper, the copper will preferentially remain as a sulfide compound until all of the other metals have been oxidized. The oxidized metals combine with silica to form a silicate slag that floats on the matte and is removed from the system. Reverberatory furnace smelting chemistry can be approximated by the following chemical equations: FeS2 + O2 - FeS+ SO2 (1) The formation of FeS ensures that any copper present other than as sulfides will be reduced by the relationship: CuO2 + 2FeS + O2 - CuS + 2FeO+SO2 (2) or 2Cu +FeS - Cu2S + Fe (3) As the molten charge travels down the furnace, continued oxida¬tion of the iron minerals and sulfurization of the copper minerals occurs. When all of the copper has been converted to sulfides, the iron sulfides can then be further oxidized as: FeS + (3)2 O2 FeO + SiO2 (4) The FeO reacts with the silica added as flux in the furnace charge. A simplified equation is: FeO + SiO2 -FeO SiO2 (5) The iron silicate slag formed is skimmed from the surface at the end opposite the burners. The copper content of reverb slag is usually less than 0.6% Cu and is discarded. Matte is removed along the side wall and is taken to the converter for oxidation of the remaining sulfur and iron. The main objectives in reverberatory smelting are to produce a molten Cu2S-FeS matte containing 30-60% Cu and a throwaway slag. Production of matte permits complete conversion of all copper minerals into copper sulfides, which can migrate because of specific gravity differences, through the lighter slag layer. Also, the molten matte droplets collect the noble metals, gold and silver, as the matte settles in the furnace. The large settling area of the furnace provides enough separation time to produce a low grade slag, which can be discarded without further processing. High heat losses are associated with reverberatory smelting be¬cause of the large volume of gases sweeping through the furnace. Therefore, an outside source of heat is required to keep the smelting reaction going. Natural gas, fuel oil, or pulverized coal are used as this heat source.

Jan 1, 1985

By J. J. Zaluski

The Surface Mining control and Reclamation Act (public Law 95-87) (here-inafter the "Act" or "SMCRA") passed by congress in August of 1977 represents a comprehensive federal scheme for controlling surface coal mining and the surface effects of underground mining through permitting requirements, performance guidelines, and reclamation planning. While the provisions of the Act have been the subject of numerous legal challenges and court battles over the years, it is difficult to identify a more controversial program within the Act than the provisions for designating lands as unsuitable for surface coal mining operations. The lands unsuitable designation process provides for the acceptance and review of petitions submitted by citizens or organizations seeking to have specified land areas designated unsuitable for all or certain types of surface coal mining activities. In filing these petitions, the interested parties or petitioners are required to make allegations about potential adverse impacts on people or the environment and submit evidence supporting their allegations.

Jan 1, 1992

By Liu Cheng-si

The number of control plans for placing control devices in a ventilation network is surprisingly large, but the research result indicates that not all control plans are feasible. The feasibility of a ventilation network control plan depends on two factors. One is the influence of the network structure. The structure must contain one independent variable-flow airway in a non-controlled loop. Otherwise, the control plan is unfeasible. The other is the combination of the air resistance, quantity, pressure and other parameters. Under some conditions, the selected values of these parameters may result in an unfeasible plan. As to the influence of the network structure, when the network structure is simple, the feasibility of a control plan can be judged directly. However, for the influence of the parameters, the feasibility of a control plan must be examined through calculation. The control position has been extended into the natural-splitting subnetwork from the conventional constant-flow subnetwork. This technique is theoretically significant. The extension of control positions results in a great increment in control plans and variation in parameters. At present, the calculation methods of the ventilation network control plans are all available. They are quite useful in selecting desirable plans. However, among the plans found, some are impractical or even unfeasible. If the unfeasible ones can be eliminated at first, much time can be saved in design and calculation. This also facilitates management and decision making.

Jan 1, 1991

By J. Evans

Including: Tailings thickeners, CCD?s, paste thickeners, HI-rate thickeners, lamella thickeners, high compression thickeners, clarifiers etc. Flocculant dosing control for mining thickeners and clarifiers is influenced by a number of process factors. 1. Flow rate into the thickener or clarifier a) As the flow rate increases into the thickener or clarifier ?retention time? decreases which causes a greater affect hydraulically on the settling solids. So as the flow rate increases it will generally mean an increase in flocculant dosing rate. b) As the flow rate decreases into the thickener or clarifier the retention time increases which reduces the hydraulic affect on settling, improving settling rates. This will generally mean that as the flow rate decreases, we will decrease the flocculant dose rate.

Jan 1, 2011

By G. Wayne Clough

During shallow tunneling in an urban environment, deposits or pockets of saturated soil or fractured, weathered rock are often encountered. Under such conditions, special problems with tunnel support, underpinning of structures adjacent to the tunneling, and/or flow of groundwater into the tunnel occur. If the ground conditions are appropriate, i.e., the soil is sandy, silty or fissured, or the rock is weathered or fractured, the solution to these tunneling problems may be chemical stabilization of the ground. Injection stabilization as an aid to tunneling is practiced extensively in Europe and its use is increasing in the U.S. The advantages of this technique over conventional solutions can be substantial in terms of cost and time, especially in mechanized tunnel boring where even a small zone of soft ground can bring the tunneling to a complete halt. In this paper European practice in using chemical ground stabilization for urban tunneling will be reviewed. In contrast to previous papers which have dealt with specific applications (1,5,8,9) this paper will broadly cover the subject, addressing itself to grouting techniques, costs, the reasons for grouting, philosophy of the users towards grouting, design of grouting solutions (or lack thereof) and methods of quality control. Differences with U.S. grouting practice are also noted. The information presented is derived from several visits to Europe, discussions with European and U.S. grouting personnel, and the available literature (2). The author's most recent European trip was made under the auspices of the U.S. Department of Transportation in conjunction with a research study being performed at Stanford University; a detailed report of this visit is available in reference (6).

Jan 1, 1976

Bioleaching of solid wastes lithium ion battery industries was carried out in this investigation. A new method for recovery of cobalt, potentially the basis of an economic and environmentally friendly process was examined. The present study was conducted using chemolithotrophic and acidophilic bacteria Acidithiobacillus ferrooxidans and some mixed thiobacilli collected from abandoned mine drainage. These organisms were able to utilize sulfur and ferrous ion as energy source. Bio-dissolution of cobalt was found to be faster than lithium. The effect of initial Fe(II) concentration, initial pH and solid/liquid (w/v) ratio were studied in detail. With increase of time of leaching the dissolution of cobalt was found to be increased and this must be due to competitiveness of the mixed thiobacilli for utilizing the energy source among them. Since the bacteria are belonging to acidophilic group the higher pH studies revealed a decrease trend in metal dissolution. Higher solid/liquid ratio also found to be detrimental for the bacterial activity. It seems bacteria are not resistant to higher concentration of the metal. The optimized conditions for bio-dissolution were sol-id/liquid (w/v) ratio - 10 g/L, initial Fe(II) concentration - 5 g/L, elemental sulfur - 1% (w/v). In the optimized conditions, cobalt dissolution was observed to be about 75 % whereas that of lithium was 15% after 25 days.

Jan 1, 2006

By Natalia Konstantinova, Georgy Novikov, Pavel Rekant, Goergy Cherkashov, Olga Bogdanova

The economic interest of oceanic ferromanganese crusts and nodules is determined by high grades of major, rare and earth rare elements in these types of marine minerals [1]. Modern oceanic ferromanganese deposits have a global distribution with the largest fields in the Pacific Ocean. The Arctic Ocean still remains a poorly explored region. The first ferromanganese deposits from the deep part of the Arctic Ocean were recovered almost at the same time in 2012 both in US and Russian cruises to the Chukchi Borderland (1) and Mendeleev Ridge (2). Preliminary results of mineral deposits from the first area were reported at UMI-2012 by James Hein et al. [2]. We present here the data of ferromanganese deposits from the Mendeleev Ridge.

Sep 1, 2014

By S. B. Patton

A computer model, which quantitatively utilizes the relationship between the interactive and dynamic processes of methane drainage, mining, and ventilation, is presented. The model includes simulation of the coalbed methane reservoir for prediction of gas-emission rates under the influence of degasification wells and longwall mining, ventilation network-generation, and ventilation simulation. As mining progresses step-wise through the coalbed-methane reservoir, the ventilation network is created and subsequently simulated, iteratively determining fan requirements to safely reduce methane concentrations. The model can be used to quantitatively study the effectiveness of methane degasification on the ventilation system in a longwall panel.

Jan 1, 1992

By W. A. Steingraber

This paper discusses the application of deep well disposal techniques to the problem of disposing of large volumes of low level radioactive wastewaters generated by the in situ uranium mining industry in Seth Texas. Data is presented on wastewater composition and volumes, geologic and hydrologic parameters of the disposal reservoirs, tell construction techniques, well operation, well monitoring requirements, and critical factors in evaluating the Safety and environmental impact of a deep injection well system.

Jan 1, 1980