Search Documents

By Margaret Armstrong, Chris Roth

One advantage of kriging is that it provides both an estimate of the block or point grade, and an indication of the local precision via the kriging variance. If one assumes that the estimation errors are normally distributed, then confidence intervals for the grades can be calculated. But in mining, grades are rarely normally distributed; in general, they are skew. This is particularly true for precious metals. In this paper we study confidence intervals for variables with non-normal distributions. Using a non linear geostatistical technique, the grades are transformed into their normally distributed equivalents. Confidence intervals are obtained for these normal variables, and back transformed to give the corresponding confidence intervals for the grades, for either points or blocks. This approach is applied to gold data from the Witwatersrand basin in South Africa.

Jan 1, 1996

By E. F. Schnitzer, C. Lidstone, D. Cramer, P. J. Wampler

The River Island mining site is located at approximately river mile (RM) 15 on the Clackamas River, a large gravel-bed river in northwest Oregon. During major flooding in February 1996, rapid channel change occurred. The natural process of meander cutoff, slowed for several years by dike construction, was accelerated by erosion into gravel extraction ponds on the inside of a meander bend during the flood. In a matter of hours, the river cut off a meander and began flowing through a series of gravel pits located on the inside of the meander bend. The cutoff resulted in a reduction in reach length of approximately 1,100 m. Erosion by bed lowering, knick point retreat and lateral erosion of upstream river banks occurred quickly. Within two days of the peak flow, 3.5 hectares of land and 105,500 m3 of gravel were eroded from the river bank just above the cutoff location. Much of this gravel moved a short distance downstream into the excavation. Reach slope increased from 0.0022 to approximately 0.0035 in the cutoff reach. Between 1996 and 2003, the knick point from the meander cutoff has migrated 2,290 m upstream, resulting in increased bed load transport, incision, and local lowering of the water table. In 1993, prior to the meander cutoff, transects were surveyed in the River Island reach upstream of the cutoff location. Resurvey of these transects and aerial photo analysis indicates that 96% of the knick point migration occurred during the first winter following meander cutoff. Connection of the flowing river to the off-channel ponds has had minimal effect on water temperatures in the mainstem Clackamas River. It is likely that this minimal change in temperature will decrease as ponds are isolated from active river flow by gravel bar deposition. Fish net-ting in spring 2002, suggests that salmonid use of the pond in the spring is minimal. The most abundant native species netted were large-scale sucker and northern pikeminnow. The most abundant non-native species netted was brown bullhead. Early regulation by state and federal agencies did not adequately evaluate potential impacts to the river and the floodplain; nor did it evaluate future impacts related to geomorphic processes and sediment transport. New permit evaluation methods, currently implemented by both Oregon and Washington, incorporate 1) river dynamism through historic river migration analysis; 2) stability of human structures in light of river dynamics; and 3) sediment transport and its impact on channel stability and dynamics. The gravel pit capture at River Island highlights the potential risks of mining in an active secondary channel of a large gravel-bed river. Mining deeper than the depth of the adjacent channel, within the active migration zone, may increase off-site impacts. In locations where multiple gravel excavations are present within the meander zone, a comprehensive reclamation and restoration plan should be developed which provides long-term channel stability within the natural variability of the entire river reach.

Jan 1, 2006

By Rainer Kahrger, Guenter Ewald

The topic of this paper is to demonstrate the development of mobile crushing installations from throughput capacities of 200 tons per hour, to mobile and semi-mobile large- scale crushing installations with throughput capacities of 3,500 up to 10,000 tons per hour. Basis are approximately 140 mobile and semi-mobile crushing installations which have been built since 1956 or were on order in 1987. [FIGURE 1. Total Number of Mobile or Semi-mobile Crushing Plants] Sixteen of these approximate 140 mobile and semi-mobile crushing installations have a throughput higher than 3,500 metric tons per hour. Mobile crushers were developed more than 25 years ago in Europe for the quarry industry, which had special requirements - fairly low capacity, mostly softer and less abrasive material (limestone) and full mobility. So the majority of the units up to about 1980 were fully mobile, having a fairly small capacity and utilizing mainly hammermills, double roll and impact crushers. It was only when the mining industry and large quarries picked up the concept in the early 1980's that a drastic increase in capacity took place. Even though the first mobile crusher in a true mining application went into service in 1971, it took another 10 years before it proceeded in a larger scale. This trend was obviously supported by the drastic fuel price and energy cost increase in the mid 70's. Since the cost of conveying material is substantially cheaper than trucking it, the increase in energy cost, combined with increasing haulage distances provided a strong incentive. Figure 1 shows clearly the throughput distribution of all crushing installations and it also shows the sharp increase in the throughput capacities within the last few years.

Jan 1, 1989

By E. S. Smith, Sunirmal Banerjee

INTRODUCTION Social awareness of the detrimental impact of man-made wastes on our environment has grown considerably during the last two decades. Increased public and institutional concerns have resulted in the implementation of a wide variety of regulatory controls of disposal of wastes. These regulations have often reflected significant conservatism in expecting guaranteed elimination of pollution risks. This sort of expectation assumed a state of knowledge which was not readily available to the major producers of wastes. The mining industry, in particular, has been affected by such regulations in terms of excessive costs and loss of benefit. As a result, investigations are in progress (1) to generate newer methods for satisfactory stabilization of mine and mill wastes and (2) to apply the available technology to achieve the standards set by the regulatory agencies at reasonable costs. This paper presents a conceptual scheme for stabilization of mill wastes by suitable management of operations and accelerated consolidation of tailings slurries. The main discussion in this paper is aimed at the ability of the proposed scheme to address the major considerations in effective disposal. Comparison in both cost and effectiveness are also made between the proposed scheme and various other currently used disposal concepts. MAJOR CONSIDERATIONS IN EFFECTIVE DISPOSAL The primary objective of an effective tailings disposal scheme is to provide containment of the contaminants in such a manner that the undesirable impact of the wastes on the three basic elements of our environment--land, air, and water-would be minimal. Bearing the above objective in mind, one may justifiably list the major considerations in the choice of the disposal scheme in terms of its effects on land, air, and water (Bromwell, 1976) as follows: Effects on Land (1) whether the scheme makes optimal use of land.

Jan 1, 1980

By K. E. Kolm, W. H. Langer

Developing natural aggregate resources (sand, gravel, and stone) creates environmental impacts. A systems analysis method has been designed to characterize the components of the environmental system, identify potential impacts to those systems, and evaluate the extent of those impacts. The step-wise method consists of problem definition, data collection, preliminary conceptualization and characterization, additional data collection, data analysis, and refinement. The method requires analyzes of various systems making up the environment, including land surface, geomorphic, subsurface, and groundwater systems. After system characterization is complete, the method focuses on identifying and evaluating potential environmental impacts to determine acceptable mining strategies.

Jan 1, 2001

By M. Lotfi

The criteria for evaluating equipment operator performance were identified as the changes in reaction time, the changes in physiological responses, and the changes in subjective reporting of stress. Data were collected while the Subjects operated a front-end loader simulator. This report out-lines the components and the tasks generated by the simulator. It explains the simple and basic assumptions underlying the design of the simulator and the methods of data collection. Improvements that can facilitate the collection of data, including the connection of the simulator to a portable personal computer for on site use are discussed. Statistical analysis of data showed significant deterioration in performance. The report concludes that operator performance can be measured and improved. This report shows that the operator tasks can be simulated by means of simple simulators, the complexity of which is determined by the availability of funds and the area of interest of the investigator.

Jan 1, 1989

By D. L. Romero

The Line Creek Mine is operated by Crows Nest Resources Limited, a wholly owned subsidiary of Shell Canada Resources Limited. It is located approximately 25 km north of Sparwood in southeast British Columbia (refer to figure 1). The Line Creek coal deposit is part of the Upper Elk Coalfield in the East Kootenays. The coal is a medium volatile, low sulfur, bituminous coal and is used as a coking coal. Coal close to the outcrop is typically of low F.S.I. and is processed for thermal use. The present pits have a total coal reserve of 30 million clean tonnes and is a multi-bench, open-pit operation. The coal is recovered by front shovel and backhoe combination, and hauled to the plant with a fleet of 120-tonne and 40-tonne capacity trucks. Line Creek is unique in that it can simultaneously treat both metallurgical and thermal coal in separate processing facilities (refer to figure 2). Run-of-mine coal is delivered to the truck dump. The plus 50 mm material is scalped off and reduced to minus 50 mm in two rotary breakers. The raw coal is then conveyed to one of five, 5000-tonne capacity, silos. Typically one silo is used for thermal coal and four for metallurgical coal (refer to figure 3).

Jan 1, 1991

By P. C. Thakur

The history of coal mining in the United States of America and the rest of the world is replete with mine explosions and consequent loss of lives. Serious efforts in the USA to recover methane prior to mining and post mining started about forty years ago. CONSOL Energy Inc. and government agencies, e.g., the erstwhile US Bureau of Mines developed several techniques of methane drainage, such as in-mine horizontal drilling, vertical gob wells, hydrofracing of vertical wells and horizontal drilling from surface. With the current technology, thirty to sixty percent of total methane emissions from a mine can be captured making the mines much safer and more productive. Drained methane is often marketed to defray the cost of methane drainage. This paper is an anthology of these developments and describes how coalbed methane, which used to be a bane, has become a boon for the coalmining industry.

Jan 1, 2003

By John Turner, John A. Gibson, David Cass

Contents A. Introduction B. Description of Robbins Company involvement in several of the English Channel Tunnel projects C. Identification of project requirements and comparison of TBM features D. Description of the manufacturers separate roles in the -235 (T-1) TBM E. T-1 performance to January 15, 1989 F. Summary

Jan 1, 1989

By Phillip R. Moyle

Voluminous deposits of commercial-grade phosphate occur in sedimentary strata in a 350,000 km2 (135,000 mi2) area of the middle Rocky Mountains of North America known as the Western Phosphate Field. The Permian marine strata that host the phosphate were deposited on the western margin of the North American craton and subsequently deformed, first by folding and thrust faulting of the Laramide orogeny, and then by Cenozoic Basin and Range block faulting. Carbonate fluorapatite is the primary phosphorus-bearing mineral. Organic matter is abundant in some strata, and both biogenic and non-biogenic pyrite are also present. Certain strata are enriched in several trace elements, especially in arsenic (As), cadmium (Cd), chromium (Cr), copper (Cu), molybdenum (Mo), selenium (Se), vanadium (V), uranium (U), and zinc (Zn). Phosphate has been mined from the Western Phosphate Field for nearly 100 years. Phosphate mining and processing constitutes the largest mineral industry of Idaho, producing more than $600 million in processed mineral value in 1997. Resource management agencies, phosphate producers, and others are concerned about the release of Se from phosphate mine wastes, especially at Maybe Canyon, and the potential effects that Se and other trace elements may have on the environment and on human health. U.S. Geological Survey (USGS) Mineral Resources Team scientists initiated a multidisciplinary study of the Permian Phosphoria Formation and related rocks in the south- eastern Idaho sector of the Western Phosphate Field in response to a request by the U.S. Bureau of Land Management (BLM). Studies to date reveal that Se is present in several phases, including native Se, and in an as yet unidentified form, possibly an organo-Se compound. Selenium is also present in pyrite and sphalerite. Selenium concentrations range from 1.2 to greater than 1,000 parts per million (ppm) in samples collected from exposures of the Meade Peak Phosphatic Shale Member of the Phosphoria Formation (Meade Peake) at Enoch Valley. The results suggest that Se concentrations vary spatially across strata and with depth, perhaps comparable to spatial variations of phosphate and organic carbon concentrations throughout the Western Phosphate Field demonstrated in previous studies. Some Se-enriched strata may be of adequate dimension to allow selective extraction during mining. Such units could be handled separately from the main ore process or waste streams and isolated in order to reduce the potential for release of Se to the environment

Jan 1, 2001

By D. L. Lampshire

Biological leaching using native heterotrophic bacteria was studied by the U.S. Bureau of Mines as a means of extracting manganese from a domestic low-grade wad ore. Column heap leaching simulation techniques were employed using molasses as the nutrient source for the bacteria. These column studies were designed to investigate the effects of molasses medium flow rate, concentration, and replacement interval on the extent and rate of manganese extraction. .Results showed that flow rates between 0.41 and 8.1 L/min/m2 had little impact on manganese extraction. The total amount of molasses used did have a direct effect on the extent and rate of manganese extraction. Manganese extractions over 90-pct were obtained in 12 weeks of bioleaching with 2-week medium replacement cycles.

Jan 1, 1993

By Michael G. Nelson

Underground coal mining practice often requires that some coal be left in place at the seam boundaries after mining, for purposes of ground control, quality control, machine guidance, or good operating practice. Many methods for measuring the thickness of boundary coal have been developed, but only the natural % R gamma background method as bee used in routine operations. Use of this method is constrained by the level and consistency of the natural gamma background in the bordering strata, the accuracy of the gamma detection instrument, and the elevation profile of the seam boundary being detected. Computer simulations for three commercially available gamma detection instruments, designed for mine use, showed that measurement of boundary coal thickness by the natural gamma method can provide satisfactory input for horizon control systems when the gamma detector is large, when the sensor is mounted on the mining machine, and when the elevation profile of the seam boundary does not change rapidly in the direction of advance.

Jan 1, 1993

By L. L. Oriard

The author describes three case histories of fracture-control blasting demonstrations. This is a technique in which the walls of blast holes are scribed or notched in order to enhance the development of blast_induced fractures, and to control their direction. One demonstration was that of a tunneling application in a rock that was generally competent but strongly foliated, hence strongly anisotropic. P second test was conducted for perimeter blasting of a structural excavation in a massively jointed limestone. A third field test was conducted for tunneling through an old concrete structure. Increased applications are envisioned with new tool modifications being developed at the University of Maryland.

Jan 1, 1981

By Otis M. Clarke

The purpose of geochemical research in the Alabama copper belt is to re-evaluate geochemical prospecting methods as related to igneous and metamorphic rocks in a humid climate. It is also a correlation of laboratory research on copper mineral solubility with geochemical anomalies over known mineral deposits. Geochemical prospecting in warm humid climates involves different problems and conditions than geochemical prospecting in semiarid areas. Stems and others (1972) reported soil surveys in a humid tropical environment in Bahia, Brazil, were not effective in outlining areas of copper mineralization. Clarke (1971) reported false anomalies in lateritic soils in Alabama over mafic rocks. Bjorklund (1971) reported biogeochemical sampling in Finland was ineffective in detailed work outlining potential mineralized areas, although it may serve to indicate regional areas of high mineral potential. During this investigation, water, stream sediments, residual soil, and organic matter, mainly twigs, were collected from three known copper-mineralized areas. Samples were selected so as to cross mineralized outcrops and results were correlated with copper stability charts as reported by Silman (1958) and Schmitt (1962). The geochemical research performed in Alabama should be applicable to other humid areas. Geologic, Climatic, and Pedologic Setting The area of investigation is in the southern end of the Appalachian eugosyncline in eastern Alabama. It includes the Hatchet Creek prospect, Pyriton mining district, and Stone Hill copper mine. The copper mineralization is in calcium-rich metasediments that lie along the western flank of a high rank metamorphic belt. All three deposits are in the uplands of the Ashland Plateau section of the Piedmont physiographic province. The Hatchet Creek copper prospect (Clarke, 1963; 1971) consists of three mineralized areas that contain pyrrhotite, pyrite, and chalcopyrite in small crisscrossing veinlets.

Jan 1, 1972

By M. K. Buder

Over the years, electric utilities have been faced with declining steam-coal quality, rising coal prices, and increasingly rigid and costly environmental standards. As a result, many utilities are beginning to show an interest in coal cleaning to upgrade coal by improving its heating value and reducing its sulfur content. Among the primary questions that must be answered for these electric utilities is whether the cost of coal cleaning can be offset by the potential cost savings in coal transportation and utilization in power generation. In search of at least a preliminary answer to this question, the Electric Power Research Institute (EPRI) engaged Bechtel to perform a case-by-case economic study to examine the cost effects of using cleaned versus raw coal to fuel new electric power plants. The results of two of the seven cases studied which involved western coals - one from Montana and another from Utah - are reported in this paper. Coal cleaning appeared to be a cost effective option for the Utah coal, but only marginally economical for the Montana coal. These cost results are expected to change to favor coal cleaning to a greater extent with the application of the final revised New Source Performance Standards regulating SO2 emissions just issued by the EPA. The study was based on the regulation originally proposed by the EPA under the 1977 Clean Air Act Amendments.

Jan 1, 1979

By T. E. Walsh

Introduction I will address two important alternative energy resources, solar and geothermal, with emphasis on their potential application in electric power generation. As a result of this presentation, I hope to leave you with a realistic view of the principal technology options that are being developed or that are available. Solar Types of Collection In terrestrial solar applications, the biggest challenge is to find ways of collecting the sun’s relatively low intensity energy so it can be converted economically to useful thermal or electric energy. Fig. 1 shows that there are both natural and technological ways of collecting solar energy. In nature we find that solar energy aids in the production of biological growth, rainfall, and wind, all of which can, in one form or another, be put to use in the production of heat or electric power. The sun’s rays also are collected and stored naturally in the form of heat in the upper layers of the ocean which can be put to use in the production of electric energy by means of ocean thermal energy conversion (OTEC) approaches. On the technological side, the sun’s rays can be intercepted by materials that directly absorb and convert its energy to low-grade heat, or by mirrors or lenses that focus the rays onto a material to produce high-temperature heat. The higher temperature systems can be used to drive efficient heat engines in the production of electricityy. The sun’s rays also can be collected on photosensitive materials, in either a direct or concentrated form to generate DC electricity directly. The systems I will discuss employ all of these means of collection and conversion, excluding biological and hydroelectric. The former is too ex

Jan 1, 1980

By S. Chander

The results of an investigation to characterize the chalcopyrite/solution interface are presented. Several techniques including galvanostatic and steady state polarization, cyclic voltammetry and impedance spectroscopy were used. The results show that the dissolution of chalcopyrite is incongruent. Initially, at low potentials(<O.34V), iron species are released which give rise to the growth of an iron-deficient sulfide (IDS) layer. The dissolved iron might reprecipitate as a hydroxide layer depending on solution composition. Continued oxidation involves diffusion of species through the product layer. At higher potentials (>O.48V) further oxidation leads to dissolution of copper and sulfur species with a resultant breakdown of the IDS layer. The changes in properties of surface coatings resulting from various electrochemical treatments are discussed.

Jan 1, 1991

By K. F. Jakob

Sustainable development is a principle for the way we should act in the present. It ensures also options for the future to achieve a balance between social, economic and ecology development. The efficiency of raw material utilisation is being enhanced through technological developments, starting from extraction through all the following stages of the value creation chain. The use of domestically produced resources helps to assure the technological know-how. Additional indicators being collected and published by individual companies are questionable in countries with a tightly regulated legal framework such as in Germany, but make sense in developing and threshold countries. Sustainability in terms of efficient use of raw materials will manifest itself at the next stages of the value creation chain. Examples for efficiency improvement can be found in the steel, the power generation and agriculture industries. The approval procedures for German mining operations entail an internationally extremely strict assessment of the potential impact on the environment. All the mining activities include remediation and recultivation where the practise in Germany has become model character by international levels.

Jan 1, 2005

By K. M. Mohamed, I. B. Tulu

"Failures of coal ribs are major hazards in underground coal mines. For the period of 2010 to 2014, rib falls were the leading cause of groundfall fatalities and accounted for 35% of all groundfall-related fatalities. Currently, the National Institute for Occupational Safety and Health (NIOSH) is conducting a research project to develop an engineering-based design methodology for rib control in coal mines to reduce rib fall accidents and fatalities in underground coal mines. Numerical models can be used as part of the design methodology provided the models are appropriately calibrated and verified. The paper presents a coal rib model to simulate the mechanism of the coal deformation and fracturing that can lead to stress-driven rib falls. The proposed coal rib model was calibrated against published data from an instrumented rib site at the West Cliff mine in Australia. Fracturing of the coal rib was defined by critical values of shear strain of the coal material and rib displacement. A critical plastic shear strain of 2.8% and a sudden increase of rib displacement of 30 to 45 mm were sufficient to develop a fracture plane in the rib model. Accordingly, a discontinuous rib deformation was achieved and it compared favorably against field monitoring data. INTRODUCTION Coal ribs are the vertical walls of coal formed when entries are developed in a coal bed. Failures of coal ribs are a major hazard in underground coal mines. Furthermore, failing ribs can contribute indirectly to roof and floor instability by increasing opening widths across intersections and entryways. Over the last 18 years, there has been a continual occurrence of injuries and fatalities in underground coal mines due to rib falls. For the period of 2010 to 2014, rib falls (excluding longwall face and bursts) were the leading cause of ground fall fatalities and accounted for 35% of all groundfall-related fatalities [1]. Despite the threat of rib falls, the amount of rib falls and rib support research conducted in the U.S. is limited compared with what has been done in pillar and roof support design. Currently, the National Institute for Occupational Safety and Health (NIOSH) is conducting a research project to develop an engineering-based design methodology for rib control in coal mines to minimize the number of rib fall accidents and fatalities in underground coal mines."

Jan 1, 2016

By J. P. Barbosa, R. V. V. Araújo, R. B. E. Trindade

Bromide stabilizes the auric or aurous ion by forming a stable complex in acidic aqueous solution. The oxidizing agent normally used for the process is bromine, which is a corrosive liquid with high vapour pressure. This is, in fact, the main reason why it has not found acceptance yet as an industrial oxidant for gold. Ferric ion with hydrogen peroxide and/or sodium hypochlorite have already proved to be effective oxidants for the dissolution of gold from a rotating disc in a bromide-containing aqueous solution. In the present work, preliminary tests with four selected ore samples were tested to evaluate the dissolution of gold with the same system already tested with the rotating disc (Br-/Fe3+/H2o2/NaCIO). Compared to the conventional cyanidation, results were superior in one instance only. The major obstacle seems to be the maintenance of a suitable potential to allow the complex formation. However, the studied system may be interesting, is in some situations it may yield better results than conventional cyanidation; therefore, further investigation seems to be worth doing.

Jan 1, 1995