Search Documents

By Peter Fordham

A Norbridge review of 25 top mining companies highlighted financial problems for many firms. To better understand these results, Norbridge benchmarked 17 mining companies to understand the problems that companies face, the methods being used to improve performance, and the results that have been achieved. The study indicates that many mining companies in three sectors-coal metals, and non- metallic minerals-have implemented new strategies to improve performance. Many of these strategies supplement traditional initiatives with two types of process improvement efforts, facility-specific and company-wide, to help generate performance gains. The study compares the results of these strategies in each sector. INTRODUCTION imes are tough in the mining industry. Norbridge reviewed financial results of 25 top mining companies for the past 2 years-seven coal companies, twelve metals companies, and six non-metallic minerals firms.*The study found that 40% lost money in 2002, and * Coal companies include Alliance Resource Partners, Arch Coal, Consol Energy, Massey Energy, North American Coal, Peabody Energy and Westmoreland. Metals producers include Barrick Gold, Cleveland-Cliffs, Coeur d'Alene, Falconbridge, Freeport McMoran, Grupo Mexico, Inco, Newmont Mining, Noranda, Phelps Dodge, Placer Dome, and Teck Corninco. Non-metallic firms include Florida Rock, IMC Global, Martin Marietta Materials, Oglebay Norton, PotashCorp and Vulcan Materials. Information is from public sources, e.g., annual reports, company Web sites.

Jan 1, 2004

The Boliden Aitik concentrator in Sweden processes 2,000 tph of low grade copper ore. The plant consists of five grinding lines feeding four bulk flotation banks with a scavenger concentrate regrind mill, and a column cleaner circuit with a regrind mill. The authors installed a model-based expert, optimizing control system to maximize copper recovery in the bulk flotation circuit while maintaining an appropriate copper grade in the cleaner feed. The optimizing control system uses on-line assays and calculates and implements set points for cell pulp levels, air rates and reagent addition rates. It combines the power of a dynamic population balance model which estimates mineral liberation in each stream, an optimizer which computes appropriate set points and a rule-based module which implements the strategy. The benefits have been evaluated over three months. The model-based expert, optimizing control system generates a measurable increase in copper recovery, around 0.5 per cent and an optimized bulk concentrate grade. The need to maintain the optimizing control system and other practical aspects are discussed.

Jan 1, 1998

By F. Daviess

A requirement for geological controls during orebody modeling results from the recognition of heterogeneous geological characteristics and/or abrupt variations in orebody geometries. While purely statistical methods are often sufficient for modeling uniform homogeneous deposits, and the only recourse for many that are extremely complex, geological interpretations can be extremely valuable as controls during the modeling process. The advent of relatively inexpensive, sophisticated graphical computer hardware and software has focused considerable attention on the three dimensional visualization capabilities now available to the mining industry. Orebody geometries can be easily imported into many systems as wireframe or solid models, rendered with shading and color, rotated in space, exploded into composite parts, zoomed into and otherwise displayed to awe any audience. The requirements for an initially meaningful, accurate, geological interpretation are sometimes lost when the focus is on an apparently complex, highly resolved end product. Details of the initial data and sensitivities of modeling assumptions are not always sufficiently scrutinized. Software capabilities have extended the geopoetic license into three dimensions. The new tools, while greatly facilitating model construction and rendering, have done little to expedite basic data preparation and analysis. This paper attempts to briefly summarize the purpose and method of the construction of geological controls. The examples selected are from wire­framing and block modeling; application software processes commonly used in the mining industry today.

Jan 1, 1992

By M. G. Rylatt

The Ekati process plant flowsheet features the common steps in diamond recovery plant design. Primary treatment and concentration is by crushing, scrubbing, high-pressure grinding rolls and heavy medium separation (Fig. 1). Secondary concentration is by an attrition mill; wet, high-intensity magnetic separation and X-ray sorting (Fig. 2). All of these are performed on site, although final sorting of the diamonds into commercial categories will be carried out elsewhere. The initial throughput rate is 9 kt/d (9,900 stpd), increasing to 18 kt/d (20,000 stpd) during the first 10 years of operation. A range of ore characteristics will be encountered that will effect the plant operating conditions during the life of the mine. The adopted design envelope is based on these expected variations. The design is based on the use of large-scale equipment, incorporating the latest and most efficient technology available. Where proven technology exists, no attempt was made to reinvent the wheel. However, where recently developed technology offers a significant advantage, this has been incorporated into the design. The Ekati run-of-mine (ROM) and coarse ore handling facilities are unheated, to take advantage of the better handling characteristics of the frozen ore in winter. The stockpile reclaim features an MMD mineral sizer (a toothed roll crusher) to minimize the problems of handling thawed, sticky kimberlite in the summer and break frozen lumps in the winter. All processing downstream from primary crushing and the coarse ore stockpile is carried out in a temperature-controlled environment in the main process plant building. Personnel involvement in the process is mini¬mized by using a Modicon Quantum series PLC with human-machine-interfaces (HMI) running Wonder-ware software on dedicated personal computers.

Jan 1, 1999

By T. J. Cox

The Red River is located within the Sangre De Cristo Mountain Range in northern New Mexico. An approximate 12-mile segment of the river from the town of Red River to the village of Questa (Questa) includes several hydrothermal alteration zones. Alteration ?scars? formed as a result of rapid chemical weathering and physical erosion of pyrite-rich hydrothermally altered rocks. Storm water runoff from the scar drainages contributes metal-laden, acidic water to the river and creates a visible plume of discolored water in the river. Acidic runoff reduces the river pH from 7 to the mid 3s for at least 2 hours during large storms and the low pH water continues downstream. Runoff from scar drainages increases some metal concentrations in the river from below chronic ecological criteria to as much as two orders of magnitude greater than acute ecological criteria, and results in acutely toxic conditions for macro-invertebrates. A general improvement in the river?s water quality occurs downstream due to dilution from tributary inflow from non-mineralized watersheds, the natural buffering capacity of the river, and storm water controls at the Chevron Mining Inc. Questa mine.

Jan 1, 2011

By N. Aouad

Dump truck operators are exposed to whole-body vibration (WBV) levels that exceed the International Standard Organization (ISO) 2631-1. The WBV level measured by RMS acceleration value, for operator comfort, and long-term health and safety is under 0.315 m/s2 by these standards. However, fundamental research by Frimpong and Aouad (2009, 2012) and field experimental study by Kumar (1999) have shown that operators are exposed to extreme WBV levels exposing them to injuries and musculoskeletal diseases in the long-term. These extreme WBV values in the vertical direction are equal to 3.56 m/s2, 1.12 m/s2 and 0.87 m/s2 for the operator?s seat, lower-back and cervical regions, respectively. This paper will outline current research to solve these problems. Keywords: WBV, Truck Vibrations, MSC.ADAMS, Virtual Prototyping

Feb 27, 2013

By A. H. Balch

A physical elastic seismic model, based on the Peoria oil field was constructed and used to produce multi mode cross-borehole seismic data. Because this was a physical model, it was necessary to deal with a complex wave field consisting of compressional waves, shear waves, and converted waves. The recorded raw data were complex, have no resemblance to the inter-well geology, and were difficult or impossible to interpret. These unintelligible data sets were extensively computer processed. Detailed, accurate, images of the inter-well structure, and reflecting horizons were obtained as a result of this processing. This investigation demonstrates that excellent, accurate images of the inter-well geology can be obtained by skilled seismic cross-well data acquisition and extensive careful computer processing.

Jan 1, 1993

The Forestry Reclamation Approach (FRA) specifies that the upper 1.22 m of material on the reclaimed surface should be left as uncompacted as possible to facilitate tree root growth. One of the main concerns about applying the FRA to steep slopes is that the upper 1.22 m of material could cause the reclaimed slopes to be unstable. Successful application of FRA on flat and rolling surfaces precipitated this investigation. Details of a field investigation conducted at a steep-slope mine are available in an earlier publication (Kumar and Sweigard, 2011). A total of 70 survey monuments were driven into the slope in a regular pattern to monitor slope movement. Quarterly surveys of the monuments were done to quantify any type of mass movement either horizontally or vertically. The methodology proposed for slope movement was verified using numerical models. Analytical models based on limit equilibrium technique and numerical models based on the finite element method were developed for slope stability analysis. The limit equilibrium analysis was done using Geo-Slope software following the Simplified Bishop Method. The finite element (FEM) numerical model was developed using the Plaxis computer program following the strength reduction technique. Two kinds of slope stability analysis were performed: first with the top 1.22 m of loose material and second without top loose material. Finally, the field investigation results were compared with stability analysis results. Both of these approaches showed that application of the FRA on steep slopes is not causing any significant instability problems that would not exist otherwise for overly steepened slopes. Keywords: Forestry reclamation approach, steep slope, slope movement, factor of safety

Feb 27, 2013

By Christopher Haycocks

Subsidence induced innerburden shearing and stress fields, whether active or passive, frequently contribute to significant ground control failures in overlying seams. In this paper proven multi-seam technology is used on upper seams to forecast and quantify the magnitude and severity of damage and the increased mining risk due to interaction. Increased upper seam ground control problems are demonstrated using hazard mapping which provides a viable technique for utilizing damage predictions in design.

Jan 1, 1986

By G. T. Lineberry, R. Q. Honaker

Coal extraction typically results in the recovery of pure rock that ranges from small to very large quantities depending on seam thickness and other characteristics. The removal of pure rock may allow the recovery of three times the amount in middling coal particles, which has significant economical benefits. In an industrial example, a 150% increase in revenue was realized from deshaling a low-ash, run-of-mine coal and blending with a processed clean coal product. Deshaling is the process of removing pure rock from coal, which normally involves a high-density separation in a gravity-based process. The removal of the relatively pure rock near the point of extraction has the potential to further enhance the economics of an operation due to reduced materials handling and refuse storage costs.

Jan 1, 2004

By N. P. Widodo

The ventilation measurements by tracer gas method at Pongkor gold mine show that effective diffusion coefficient, E, at straight airways indicated a similar range of measured one by the laboratory experiments which can be estimated by Taylor equation. On the other hand, E of the curved airways in the mine was estimated as larger than that of the straight ones (1.5 to 32 times than that obtained by the Taylor equation and these have been compared with the data measured in Kushiro coal mine, Japan). The curved mine airways, with small curvature against airway radius and complex velocity profile, possibly give concentration ? time curves with long tailings, thus those airway conditions could make larger E. Laboratory experiments of gas diffusion by a pulsed injection of small amount gas, into straight and curved airways, have been conducted in order to investigate a range of E in mine airways. The plots of E against Reynolds number show that the present laboratory results of straight-long airways are almost close to one calculated by Taylor equation. On the other hand, the values of E measured at curved single-direction airways were smaller than that of the straight airways, which may be due to effects by secondary vortexes flow in the curved airways.

Jan 1, 2009

By Mark Gershon

This paper describes an application of a new approach to mine planning and production scheduling in a gold mine. The technique, limited to use in open pit mines (but not limited to gold), has been described previously (Gershon, 1987). The-computer program used is the HOPS software, which has been described previously as well (Gershon, 1988). The mine is scheduled for the production of 8,000 blocks out of a mine having 25,000 blocks (50 x 50 x 10). The technique is based on the concept of inverted cones (Gershon, 1987). While it does not provide a true optimization of results, it does approximate the optimal situation. As opposed to most scheduling software that only serves as a computerized notepad for the scheduler, the use of this approach allows for a scheduling intelligence to be built into the software.

Jan 1, 1989

By S. Kawatra, K. Lewandowski

Heap leaching efficiency is reduced by poor solution flow characteristics (channeling and ponding), which result from fines migration. Agglomeration of the ore can immobilize fines, but copper leaching requires an acid-resistant binder to stabilize the agglomerates. Until now, there has not been a satisfactory way to evaluate whether a binder was effective, other than squeezing a handful to see if it “feels right”. We have developed procedures to quantitatively determine whether a binder gives good performance in an acidic solution, and have identified several binders that will be suitable for copper heap leaching.

Jan 1, 2007

By Larry R. Powell

The Bureau of Mines, in cooperation with the Illinois Mine Subsidence Insurance Fund, is monitoring the response of two foundations to ground movements induced by subsidence from high extraction mining in southern Illinois. The objectives of the monitoring program are to study the inter- action between the ground surface and a foundation during a subsidence event and to determine the capability of the tiltmeter to detect and monitor subsidence movements. Tiltmeter data were obtained on two foundations constructed near Sesser, IL. One of the 30-by 40- ft foundations was constructed with a typical poured concrete footing, the other with a rein- forced-concrete footing poured on top of pol yethylene sheeting placed over a compacted layer of sand. Soil-filled bins were placed on the perimeters of both foundations to simulate superstructure loads. Monitoring pins and tiltplates were installed on the corners and midpoints of the footing. Additional survey points were established on the five-acre site to track the mining advance. This paper describes the monitoring instrumentation and techniques as they relate to the mining and site conditions. The capability of a tilt- meter to detect and follow the tilt of the foundations is demonstrated.

Jan 1, 1986

By K. V. Raj, A. Miller

"Workers at mineral processing facilities are often exposed to high levels of dust generated when ores are processed. Crushing, grinding, screening, and other processes generate large quantities of dust, which can exceed the threshold VALUES (prescribed by the Mine Safety and Health Administration (MSHA). Many ores contain quartz (silica), which has been known to cause serious health problems in workers over time. Given the structure of mineral processing plants, the airflow regime is not coherent inside the building, which may lead to multiple recirculation zones. These recirculation zones can trap dust, and concentrations of dust can then rise over time. Therefore, there is a need to understand the airflow phenomenon that occur inside of mineral processing facilities and how these occurrences interact with the dust generation processes to identify zones of potentially high dust concentration. Computational fluid dynamics (CFD) modeling can give a better understanding of the airflow and help recommend designs and methods to mitigate the high dust concentrations in a mineral processing plant. This paper presents the CFD modeling of airflow inside of a mill building to demonstrate airflow patterns that will affect the generation and subsequent dispersion of dust due to crushing, grinding, and other activities. This study was conducted by researchers from the National Institute for Occupational Safety and Health (NIOSH). INTRODUCTION In a mineral processing facility, minerals go through various mechanical processes in order to reduce their size for separation of economic minerals from gangue minerals to produce a final marketable product. This research, conducted by the National Institute for Occupational Safety and Health (NIOSH), focuses on ore mills in metal and nonmetal mining (MNM) operations, but the applicability of the approach will be valid for any large structure where workers are exposed to airborne contaminants. The processes of crushing, grinding, cleaning, drying, and product sizing in these facilities generate a large amount of dust, creating hazardous conditions for the workers in these facilities. This is highlighted by the fact that MSHA sampling data for the years 1997–2012 indicate that 12.3% and 15.9% of the gathered samples were over 100 µg/m3 for silica for metal and nonmetal mills, respectively [1]. Mineral processing operations typically use some type of engineering control to address their most significant dust sources. Engineering controls include such approaches as bag-house-type dust collectors, scrubbers, and electrostatic precipitation [2]."

Jan 1, 2018

By M. S. Klima, A. Simard, M. L. Turek

Laboratory testing was carried out to evaluate several devices for recovering clean coal from bituminous coal refuse material. The bulk of the testing focused on using a dense-medium cyclone to process -0.6-mm refuse material. A hindered-settling column and a spiral concentrator were also used to process nominal 1.2 x 0.15-mm material. Product yields and ash contents were obtained for all tests, while partition curves were generated for selected tests from which the characteristic performance parameters (relative density of separation and probable error) were determined. The results indicated that the dense-medium cyclone was capable of cleaning down to 0.037 mm, while the other devices were effective to 0.15 mm. Keywords: Coal recovery, Coal refuse, Dense-medium cyclone, Hindered settling, Spiral concentration

Jan 1, 2003

By Karoly (Charles) Kocsis, August Greth, Jon Fox

"It is the duty of the mine operator to ensure the mine environment is healthy and safe for the mine workers. For deep and hot underground mines, this requires maintaining adequate working temperatures by means of mitigating the heat load generated by strata, auto-compression, mining equipment, explosives, ground water and human metabolism. The heat load is best reduced by minimizing the amount of heat transferred to the mine air from these sources and through the use of efficient ventilation with effective cooling systems. The heat emitted by mining equipment and vehicles contributes a significant proportion to the combined heat load of an underground mine. This is especially a problem for diesel equipment due to the fact that besides heat, a large amount of water vapor is produced, which increases the humidity in the production workings. Diesel engines have proven advantageous in recent history due to their high power output and reliability. However, as mines continue to become more mechanized and deeper the climatic problems introduced by elevated heat generation will continue to rise. With that, the issue of heat generated by diesel equipment must be addressed.The economic alternative for diesel engine equipment fleets in underground mines is the electric engine. Technological advances in battery technology, increased mechanical output and improved reliability have made the electric engine significantly more competitive in comparison to diesel engines. Because electric engines do not utilize internal combustion, the heat produced by them is significantly less than the diesel engines. Battery-powered mining equipment likewise eliminate diesel particulate matter (DPM) produced by diesel engines. Utilizing battery electric equipment in underground mines provides many advantages, such as: (a) reduced heat load, (b) healthier and safer environment for the mine workers and (c) reduced mine operating costs due to lower ventilation requirements"

Jan 8, 2018

By John C. Morrisey, Harold M. Ray

With full production from the Casteel Mine in 1987 The Doe Run Company, a wholly owned subsidiary of the Fluor Corporation, encountered a significant increase of copper and iron to the Viburnum Mill. This major change of the lead, zinc, and copper metal ratios in the ore created circuit problems which adversely affected concentrate quality. Recognizing the problem, the company embarked on a metallurgical research program to include laboratory, pilot plant, and plant testing. The program developed an innovative copper prefloat process which both increased copper recovery and significantly improved concentrate quality. The process was tested and first operated at Doe Run's Brushy Creek Mill then installed at the Viburnum Mill in 1992. A brief history of development, plant operating data, and other potential applications for the patented processes will be described in the paper.

Jan 1, 1993

By R. W. Ballmer

Prior to initiating construction of a new mineral development project, sponsoring organizations must be convinced that the operation will be viable. Proof is typically provided by the feasibility study. Considerable man hours will be spent in assessing and evaluating data on the deposit, its environment, and the means of development. Impact studies must be made for various scales of operation, inclusion of by-products, new methods of treatment, deferent levels of integration, and infrastructure configuration. Examples of current materials handling cost estimates are provided from the ongoing investigation in which Amoco is a participant at Ok Tedi in Papua New Guinea and Gag Island in Indonesia.

Jan 1, 1979

By Cyril W. Draffin

Introduction Americans have long been proud of their ability to recognize a need, define it, and then develop workable solutions. The U.S. underground coal conversion (UCC) program is a good example. In 1974, the need to utilize coal resources that could not be mined was recognized, and Congress gave the Bureau of Mines $1.7 million to gain a better understanding of the UCC technology and its potential applications. Since 1977 when the U.S. Dept. of Energy (DOE) was formed, workable technologies have been tested, the market for underground coal conversion has been recognized, and extensive industrial interest has developed. Perspective The U.S. is blessed with extensive coal resources. Coal supplies about 19% of our national energy needs, yet recently promulgated environmental standards and increasing mining costs have limited direct coal use. UCC potentially can use coal that is economically or technically infeasible to mine because the coal is too thick, deep, dirty, high-ash, and wet; has an excessive angle of dip; or has unpredictable and poor overburden characteristics that make mining unsafe. Coal can be gasified underground or perhaps liquefied below the earth’s surface. Underground coal gasification (UCG) is the prime element of the underground coal conversion program. It enables coal to be converted to gas underground. UCC Coal Resource Recent data show a total U.S. coal resource base of about 6.4 trillion tons. Of this, 1.8 trillion tons might be accessed by UCC, including some minable coal. A commercial UCC process could quadruple roughly the 450 billion tons of U.S. coal reserves, which presently are recoverable by mining. The U.S. coal resources are divided into five sectors. The two most eastern sectors contain relatively thin, swelling bituminous coals that are difficult to gasify. Of the two, the bituminous coal in the Eastern Province is the most difficult because it is deeper than , in the Interior Province and the terrain is more rugged. The sector along the Rocky Mountains contains huge amounts of thick low-rank coals that are the most promising for early development by UCC. The coal has good continuity and the terrain is suitable. Low-rank coals such as subbituminous and lignite are highly reactive and tend to shrink and disaggregate when heated. Most of the coal in the Pacific

Jan 1, 1980