Search Documents

By R. L. Loofbourow

In addition, dewatering is seldom complete because of aquifer irregularities and an operator's natural reluctance to start a costly study program, provision of wells, and pumping long before mining begins. In some cases, water pumped from the mine is used in treatment. This use is suggested as a way to minimize effluent effects. The true objective of water supply, however, is to provide water of satisfactory quality at the rate needed and at the least cost. Pumping to permit efficient mining isn't likely to coincide strictly with that objective during much of the mine life. The history of mining is replete with efforts, some highly ingenious, to control mine water. Methods that might be used to tackle the challenge Operators of wet mines are faced with both obvious pumping costs and some unquantified water costs. It is possible to reduce both types of costs, generally by reducing inflow to the mine area-and a surprising number of methods have been used to do this. Both the obvious and unquantified costs at a wet mine are now multiplied by: •Increasing costs of power, labor, equipment, and supplies; •Work at greater depth and, in some cases, in wetter ground; •Increasing use of hydraulic fill; and •Increasing zeal in protection of surface and groundwater quality. There are many easily overlooked ways in which mine water may add to hazards and costs (Loofbourow, 1973). As to their importance, consider these examples: •Increased maintenance of equipment, tires, roads, and ditches; •Increased difficulty in supplying proper ventilation; •Increased hazards from ice and use of electric power; • Loss of friable ore minerals and fines stuck on conveyances and in chutes; •Need to use more expensive methods and explosives; and •Decrease productivity of equipment and personnel. Expressed as cost per unit of ore produced, these unquantified costs can be high. Ideally, advanced dewatering should eliminate most of them. Advanced dewatering is a highly effective water control method, but it isn't problem free. Mines in ideal ground for advanced dewatering are most unusual. To be effective, water must be pumped at a comparatively high rate for a period longer than the life of the mine, from below mining depth. Effects on both groundwater and surface water are likely to be drastic. of increasing mine water costs are listed in the accompanying table. Ten groups of possible methods are cited. Most have been demonstrated in mining; two are known from industries other than mining.

Jan 12, 1980

By S. K. Kawatra, S. Bagley, T. C. Eisele

To meet federal air pollution guidelines, it is necessary to remove a considerable quantity of sulfur from many North American coals. This may be accomplished by oxidizing the sulfur to water soluble forms, followed by washing the coal. Selective oxidation of the various sulfur forms can be accomplished through the use of a variety of types of bacteria. In this paper, the various bacteria and their requirements are described, and processes using bacteria to remove coal sulfur are discussed.

Jan 1, 1988

By C. J. Bise, D. A. Poukhovski

Two integral components of the 30 CFR 48 training requirements mandated for new miners, newly employed experienced miners, and the annual refresher training of all miners are hazard recognition and prevention of accidents. In these categories, instruction shall include the recognition and avoidance of hazards present in the mine, and a review of accidents and their causes. Unlike instruction preparation for fact-based material, program development for hazard recognition places a particular challenge before safety-training specialists because they are often limited in their ability to adequately gauge the trainees' levels awareness prior to training. Further, they must also assure that the training is relevant, and it is presented in a thought-provoking manner. Computer-based instruction is particularly well suited for assisting trainers in developing hazard- recognition topics because it can be used in pre-training and post-training modes for assessment of training effectiveness, in addition to use as a presentation tool. Therefore, this paper will present a recent approach developed at Penn State to apply this technology for assessment and instruction of accident prevention through hazard recognition, with an application prepared for surface coal mines.

Feb 24, 1997

By Paul Higley

Specialty Devices, Inc. and the CMRET/NIUST, University of Mississippi, have collaborated in the design and development of a new class of Robotic Underwater Vehicle (ROV) focusing on efficient, low cost, deepwater operations. The need for such a vehicle was driven by special requirements encountered in the establishment of the Gulf of Mexico Gas Hydrates Research Observatory at a depth of 850m in Mississippi Canyon Block 118 on a restricted budget. Requirements included deployment and recovery of tools and sensors and the connection of underwater-mateable electric and fiber optic connectors at depth. The standard complement of equipment required included; high-resolution video with lighting, scanning sonar, robotic arm, precision positionin and thrusters for limited transit and maneuvering. Conventional deep water ROVs are lowered in a large cage with a buoyant tether between the cage and the ROV. The tether is wound on a winch in the cage deployed as the ROV swims out from the cage. This cage is lowered on a large diameter umbilical cable with strength elements and communications elements and conductors for electric power. With increasing water depth the umbilical cable must become ever larger to accommodate increased power transmission loads and strength demands, with corresponding increase in deck handling equipment size and in turn, vessel size and overall cost. The surface ship must include a dynamic positioning (DP) system to control ship propulsion to maintain the position of the ROV cage at a position relative to the sea floor. DP ships with this capability and the ability to carry the large umbilical cable and winch are expensive.

Jan 1, 2008

By II Browne

After a decade of high copper prices, major mining companies are renewing their interest in purchasing operating properties and/or development of ore bodies. An existing operation carries with it a history that can present unique opportunities, while a greenfield operation allows for the establishment of a defined culture. Capital investments are distinctly different. A comparison of BHP Copper Robinson Operation, a greenfield property, and BHP Copper Tintaya Operation, a government owned Peruvian property, will provide insights into mining, concentrating and cultural differences between North and South American Operations.

Jan 1, 1997

By Cleophus Short

[Of the many occupations in and about the coal mines, those of the haulage crews are among the most hazardous. Statistics ship that the second greatest number of fatalities about the coal mines occur during haulage ion and through the use or misuse of haulage equipment. During the five year period between January 1, 1957 and January 1, 1962, the m stone mine had a. Sack haulage frequency of 4098 and mined 3, 541,939 toads per haulage fatality. Coal mire haulage is similar in respects to railroading. We gee very serious consideration to the instillation of tack and to the selection of the haulage crews. In doing this, we are attempting to have our coal mine haulage as. Safe as that of the railroads.]

Jan 1, 1963

By Steve Kral

The mining industry in Colorado faces the same problems the industry faces throughout the United States and the world — record low commodity prices and increasing regulatory and environmental restrictions that seemed designed to curtail mining activities. Despite those obstacles, the mining industry in Colorado still contributes about $8 billion annually to the state’s economy in the form of base and precious metals, industrial minerals, coal and associated service businesses and jobs. So the 300 attendees at the102nd National Western Mining Conference felt reason-ably positive about the industry in their state. The meeting is the Colorado Mining Association’s annual conference and was held at the Broadmoor Hotel in Colorado Springs in November. The theme was “Mining in the New Millennium — Achievement + Innovation = Survival.” Experts from Colorado’s mining industry and abroad discussed the challenges faced by the mining industry as it enters the new millennium. They offered insights into how the industry will operate during the early years of the 21st century and how it will survive low prices and increased regulatory restrictions.

Jan 1, 2000

Sandvik built its first stone crusher in 1896 and has since grown to become a world leader in mining equipment. ?We are the best in the world, and we can now be even better at making our cone and jaw crushers in different models,? Olle Lundberg, production engineer at the Sandvik Mining factory in Svedala, Sweden told freelance journalist U. Samuelsson, of mekpoint.com. As a specialty manufacturing business under the umbrella of the Sandvik Group, Sandvik Mining is a leading global supplier of equipment, tools, services and technical solutions for the mining industry. Its expertise covers the areas of rock drilling, cutting and crushing, as well as loading, hauling and the handling of materials. Lundberg, along with five colleagues, will write CNC programs for the lathes and machining centers that manufacture Sandvik?s specially constructed casting. In 1999, Sandvik chose ESPRIT computer-aided-manufacturing (CAM) software by DP Technology to program its array of machine tools, and has worked with ESPRIT reseller Holotech, based in Örebro, since 2003.

Jan 1, 2014

There are many risks associated with the storage of nuclear or other toxic wastes. One of the major risks is the escape of material from the repository. No matter how well a storage facility is engineered, the potential escape of dangerous material must be studied. This kind of study will include some estimation of the "travel path" of the particles. The travel path of a radio-nuclide particle will depend on the geological and hydrological parameters of the surrounding rocks. These parameters must be estimated from a limited number of samples available within the study area. Any estimation will -of necessity -contain a certain amount of uncertainty or "estimation error". This uncertainty will be carried through to the analysis of potential movement of particles, so that the estimated travel path itself will be subject to some error. This paper discusses an approach which may lead to a quantification of the uncertainty on the predicted travel path.

Jan 1, 1989

In the dimension stone industry, workers in processing shops may be exposed to harmful levels of respirable silica dust when conducting the different tasks in stone preparation, which include cutting, grinding, polishing, and thermaling. To protect workers from this health hazard, operators sometimes ventilate processing shops using fan-powered dust collectors to capture and filter dust. To investigate this issue, NIOSH, Pittsburgh Research Laboratory, in cooperation with a dimension stone operation, upgraded an off-the-shelf dust collector the operator was utilizing in a polishing/cutting shop. Initial dust surveys showed that the unit was under-designed for the amount of dust being generated in the shop. The objective of the research was to cost-effectively increase the air cleaning volume and improve dust capture efficiency of the unit with a larger motor and blower. The unit?s original stock 0.56 kw motor and blower was replaced with a 2.24 kw motor and matching blower to increase airflow. The unit was evaluated both in the laboratory and the shop before and after the retrofit to determine the improvement of the upgrade. The study showed that the 2.24 kw upgrade improved the performance over the original 0.56 kw motor resulting in more dust being cleaned from the ambient air in the shop. The 2.24 kw unit cleaned 19% more air and captured 32% more respirable dust than the 0.56 kw unit.

Jan 1, 2009

By Takeo Oki

A new suspension electrolysis method has been developed, which enables without any gas or dust pollutants a direct anodic extraction of zinc from zinc sulfide concentrates, while simultaneously oxidizing sulfide sulfur to elemental sulfur. The investigations were performed in a laboratory scale electrolytic cell with suspended zinc sulfide concentrate particles with or without graphite powder additions in dilute sulfuric acid electrolyte. By regulating the redox potential of the electrolysis system in combination with some additions, for example [Fe3+/Fe2+, MnO 4/MnO2, MnO 2/Mn2+ or MnO 4/Mn2+], the anodic dissolution reaction of zinc sulfide has been accomplished effectively without evolution of hydrogen sulfide. Under optimum conditions the anodic current efficiency of zinc dissolution ammounted up to 95 %, while sulfide sulfur was converted nearly completly to the elemental form. Purification by removal of sulfur and other impurities gives a zinc sulfate solution suitable for electrolysis to cathode zinc.

Jan 1, 1975

By M. D. Bishop

Early solvent extraction circuits in the uranium industry utilized bona fide kerosenes as diluents for extractant chemicals. These kerosenes were used successfully in the uranium industry; however, at least one plant was destroyed by fire resulting from the use of a low flash point kerosene. Although the term "kerosene" is used throughout the solvent extraction industry, the authors have been unable to find any use of kerosene in copper solvent extraction circuits. A term that is occasionally used with reference to diluents is "metallurgical kerosene." Such a term is unrecognizable in the petroleum industry. Kerosene [or kerosine] is a flammable hydrocarbon mixture that is less volatile than gasoline. It is produced for combustion purposes and may have variable compositions of organic compounds including alkanes, alkenes, alkines, and aromatics. Diluents are constant composition hydrocarbon mixtures developed specifically for use in solvent extraction processes. These products usually have much lower vapor pressures and higher flash points than kerosene. In solvent extraction systems, they typically comprise 70 to 95 v/o percent of the circuit organic. The primary purpose of the diluent is to adjust the extractant concentration to the working range of the operation. The diluent and extractant must be completely soluble or miscible with each other. Secondary diluent effects are to promote transfer kinetics, optimize phase disengagement, and minimize both organic in aqueous and aqueous in organic entrainment.

Jan 1, 1996

By Kirk L. Prather

Why discuss techniques of accident prod lot on? Would it not be more useful to discuss means to reduce accidents? This discussion will answer these questions by suggesting ways in which effective accident prediction techniques improve the ability to foresee and prevent accidents. Accident Prediction Process The secret to accident prediction is to utilize the tendency for history to repeat itself. The same circumstances and the same human behavior that produced accidents in the past tend to produce accidents in the present and the future. The ability to predict accident occurence in the future by projecting from the past is a statistical process. In a bookmaker's jargon this means "playing the odds" or "the percentages". A horse or a sports team may be beaten on any given day, but by skillfully assessing the factors of past performance and assigning odds, many clever bettors make money in the long run.

Jan 1, 1973

By D. R. Spears

As part of its mission to develop technology to assure a continuing supply of minerals, the US Bureau of Mines has investigated the flocculation of a Stillwater, MT, chromite ore. The ore was flocculated at different solids contents and at different stirring speeds to determine the importance and effect of hydrodynamic factors. In acidic and basic pH, the chromite ore was flocculated with high molecular weight polyacrylamides differing in the degree of hydrolysis. Polyacrylamides were found to bind to chromite ore particles through hydrogen bonding. The anionicity of the polymer and the pH affected the degree of polymer-particle interaction, which in turn affected polymer conformation at the surface. A polymer conformation with many loops and tails was used to explain high flocculation efficiency. It was found that such a conformation could compensate for poor hydrodynamic conditions.

Jan 1, 1992

By D. P. Plute

The mechanization of the materials management function must contribute to the overall goal of optimization of profits. A computerized system contributes to the profitability of the company by saving more than it costs to operate. Design and implementation of the sys- tem must respond to the needs of users, the operating environment of the property, and must support the objectives of materials management. Three basic functions interact within the scope of materials management. They are inventory control, purchasing, and warehousing which have the following objectives: 1) Inventory control-to request materials in a timely manner and in quantities that provide the best level of support to users at the lowest cost. 2) Purchasing-to purchase requested materials and services at the required time and at the lowest cost. 3) Warehousing-to efficiently receive, store, and issue materials and to prepare accurate transaction documents for the activities. The development of the mechanized materials management system will require a plan and objective analysis by management and system users of system requirements. A typical plan would include: 1) System Design Objectives-the development of objectives that support mechanization of the materials management function. 2) System Characteristics and Concepts- the development of key system concepts and characteristics, which identify the needs of materials management. 3) System Inventory Item Classification- development and assignment of inventory category codes to inventory items. 4) System Order Decision Rules-the development of decision rules and forecasting techniques to minimize the inventory investment and to provide acceptable support levels. 5) System Report Structure-the development of a report structure to support the goals and objectives of materials management. 6) System Report Design-the development and design of reports for effective utilization of the mechanized system.

Jan 1, 1979

By Jerry M. Whiting, Samuel Frimpong

Superior ventures selection and the subsequent management of their development and production are crucial in the competitive environment of the upstream minerals and energy industry. An important element of this chain is the management of uncertainty and risk dynamics. In the world of faster and more complicated technological and environmental changes, international competition and commodity market dynamics, thorough and sophisticated valuation must be carried out to establish a venture's value and return on investment. Thus, managers and investors must use methods that respond to market dynamics, investment and feasibility study options and provide relevant information for strategic investment decisions. Conventional methods have no built-in procedures to help investors analyse these options. Modern financial methods based on the dynamic arbitrage theory overcome these and other limitations of conventional methods. In this study, dynamic arbitrage theory has been used to formulate 3D parabolic differential equations that govern the stochastic processes of a copper mining venture with ongoing feasibility studies. The alternate direction implicit algorithm is used to solve the numerical approximations of the differential equations and their boundary conditions. Phase dynamics of the venture have been analysed to provide investors the appropriate timing for strategic investment decisions. The study also shows the amount and value of appropriate feasibility studies required to maximize the value of the mining venture.

Jan 1, 1996

By Henry E. Reed

This presentation is about a small company, Industrial Mineral Products, that was formed in 1972 with one product and one customer and by a series of value-added changes avoided disaster and increased sales many times over. The principal of the company stopped by my office in Seattle looking for industrial mineral opportunities in the Northwest. We got together and went through all the minerals in Ladoo's "Industrial Minerals" from Abrasives to Zircon to see if we could find something available on the vast holdings of the Burlington Northern. At that time one of our lessees was operating a silica sand mine near Ravensdale, Washington and indicated that he might be interested in selling out. This sounded interesting to my client and within two weeks the transaction was completed.

Jan 1, 1990

By P. James

Blue Planet Strategies (BPS) focuses on improved resource utilization and targets converting wastes into resources. New BPS capability (DEMET) wrings extra value from mining and processing wastes by enabling new production from waste and residual sources. This powerful platform technology provides considerable processing flexibility and enables various new economical treatment options to extract key metals from low level and process byproduct stream sources normally left as waste by traditional processing methods.[1]

Feb 23, 2014

The technical parametrization of reserves is a technique which has made an important contribution to the definition and the calculation of optimal mining projects. Its applications to a new open-pit optimization program have already been presented in various papers (François-Bongarçon and Maréchal (1976); François-Bongarçon and Guibal (1981)). The present paper gives a brief description of the general problem of parametrizing reserves before going into the details of the practical algorithms used in two typical cases, i.e. open-pit mining and mining between hanging wall and foot wall.

Jan 1, 1982

By J. R. Allen

Environmental laws and regulations have proliferated over the last two decades. 1/ Within the last year, Congress has dramatically expanded the scope of the Superfund program 2/ and has enacted significant new amendments to the Clean Water Act.3/ In addition, EPA has shown no signs of slackening the pace at which it promulgates new regulations to implement statutory programs. The agency projects that over the next few years it will issue approximately 275 new regulations under the statutes it implements. 4/

Jan 1, 1988