Search Documents

By Clyde N. Garman

Historically, Vanadium and Uranium have been precipitated together in carbonate sill circuits. A separation of the salts of the two metals was then made on the basis of the fact that the reduced, salts of vanadium are more solo to and those of uranium lose soluble than the respective salts of higher valence. In practice this was carried out by fusing the precipitated combined concentrate with salt, sodium carbonate and sodium hydroxide with oil soaked sawdust mixed into the charge as the reducing agent. Generally the fusion was carried out batch wise and the resulting slag or glass leached in water. A good, fusion and three or four decantation washes resulted in almost complete recovery of the vanadium in the liquid phase and a very high recovery of the uranium as a dense black U02 solid.

Jan 1, 1962

By Leonard Sugin

Recent changes in the field of ore and bulk commodity handling has forced a reevaluation of previously conceived notions. When vessels were small, and sources of raw material were reasonably close to areas of need, the role of the shipping terminal was of secondary importance. Now terminals must be built to take advantage of the economic benefits of the supercarriers. The shipping rates of the 80's will not be determined by the 60,000 DWT or even 150,000 ton capacity bulk carrier, but rather by the supercarriers in the 250,000 DWT class or larger. When the Suez Canal was closed, the shipping industry took a hard look at the economics of the large bulk carrier. Naval architects overcame the problems and successfully designed large supertankers, which today are plying the seas in excess of 350,000 DWT. Orders have been placed for tankers of 480,000 DWT. The shippers of dry bulk materials are now coming to similar conclusions about the economics of supercarriers. As of today, over 40 orders have been placed for vessels in the 250,000 DWT class, representing an investment of over 11/2 billion dollars, and many more are being considered. These vessels are being designed as combination ore/oil (0/0) or ore/bulk/oil (OBO's) carriers. The oil industry has seen the need for terminals which can accommodate these supertankers. The dry bulk shippers, and particularly ore shippers, must now act.

Jan 1, 1972

By D. Oyler

The National Institute for Occupational Safety and Health’s(NIOSH) Pittsburgh Research Laboratory (PRL), RAG Pennsylvania and Strata Control Technologies of Australia have collaborated to conduct an extensive study of roof bolt strata interaction at the Emerald mine in Southwestern Pennsylvania. The primary goal of the project was to obtain detailed data on the interaction between the mine roof and the support elements for use in modeling studies. The study site was a longwall tailgate subjected to high horizontal stress. Three arrays of instruments were installed at the site, one in the tail-gate entry and two in an adjacent crosscut. Pumpable concrete cribs were present in the tailgate array, and cable bolts were installed in one of the crosscut arrays. The instruments included mechanical and sonic extensometers for measuring roof movement, instrumented roof bolts, and three-dimensional roof stress cells. The study was ultimately successful in determining the magnitude of the horizontal stress concentration, the height of roof failure and the roof failure sequence, and the loading history of the primary roof supports.

Jan 1, 2004

By F. W. Brackebusch

A unique machine has been designed for mining narrow veins. The machine, called the NONN, walks on the walls of the stope and carries a boom-mounted hydraulic impact breaker. The concept of walking on the walls allows an existing muck handling system such as LHDs to operate beneath the NOMN. The NOMM has four sets of legs which can be manipulated independently or concurrently to cause the carrier to walk in any direction and to turn sharp corners. The mining rate using the breasting method is targeted to be 25 t/hr.

Jan 1, 1990

By G. Belardi, G. Marruzzo, P. Plescia

This paper presents the results of grinding tests performed on magnetite from Kiruna (Sweden) and on chromite from Skoumtza (Macedonia. Greece). Stresses were measured by XRD, which determined the variations in the characteristic structural spacings of the minerals both before and after, grinding in a HSM/250 Herzog laboratory ring mill. Anal Isis of the magnetite and c hromite crystallinstallin was performed hi measuring the broadening of the strongest diffraction peak (311). .Also, structural analysis on chromite was carried out using the Mikheev model. Ultrafine-grinding tests on the magnetite and chomite demonstrated that this type of treatment can induce profound variations m the surface-stress state. These included plastic variations of the cell followed by "chemical" stress with oxidation front the stricture to form hydroxide or carbonate, films. This can have a great influence on the mineral reactivity to flotation reagents

Jan 1, 1996

At the dawn of the computer age in the early 1950's, few people in either the minerals industry or the field of electronic data processing (EDP) would have predicted the tremendous impact that the computer has had on the way we conduct our everyday lives and businesses. Herman Hollerith himself (see next page), the Columbia University mining engineer 'turned statistician who developed the first punched card electronic tabulating machines for the US Census Office in the late 1880's, would doubt- less be amazed at the progress that has been made in the application of data processing techniques to nearly all aspects of the mining cycle (Aul, 1974). More than any other factor, the availability of economical computing equipment has led the way for the development of the broad range of mining computer methods described in this text. While limits have been identified for many of the technologies commonly in use today, new technological advancements point to continued exponential advancements in computing price-performance in the 1980's. With those advancements, we may look forward to continued expansion of the role computers will play in mineral production.

Jan 1, 1979

By T. F. Torries

Identifying high value areas of unmined coal when large quantities of coal are available relative to annual markets is difficult because of the uncertainty of when the coal is to be mined. A GIS based methodology developed to value reserve coal in a producing coal region for the purpose of ad valorem taxation also identifies high value areas for mining investment. The methodology is unique in that it accounts for most mining, environmental, and market factors to determine when specific properties are to be mined. The methodology and data base are useful for directing regional exploration and acquisition activities toward most favorable areas.

Jan 1, 1999

By P. Lan

Gold is often associated with arsenopyrite in many refractory gold ores. The selective recovery of arsenopyrite by flotation is therefore necessary in order to maximize the recovery of gold. However, the complexity of arsenopyrite flotation often makes it difficult to obtain a high recovery from real lean gold ore. This paper presents the results of arsenopyrite flotation by ultrasonic pretreatment in micro flotation experiments and bench scale flotation tests. The tests showed that pure arsenopyrite exhibited low natural floatability due to the oxidation on the mineral surface under ambient conditions. Using ultrasonic pretreatment, the oxidation film was ruptured and the floatability was enhanced greatly. The presence of Fe (III) was found to inhibit the flotation of arsenopyrite and this depression was also removed by the ultrasonic pretreatment. This result explained why the arsenopyrite in real ore is often difficult to float and how ultrasonic pretreatment can effectively improve the arsenopyrite flotation in real gold ores. Guanidine (GMM) was found to be a superior collector for arsenopyrite in acidic medium and xanthate in alkaline medium.

Jan 1, 1998

By Yoginder P. Chugh

Most mines are large producing 0-25 mmt annually. The coal is mine.) at depths ranging from .0-150 m 120-500 ft mining at 300 m .(,1000 ft) depth is anticipated in the future. Single and multiple seams ranging from 3-12 m 10-40 ft) in thickness are mined. Most overburden is unconsolidated and consists of sands, and sandy or silty clays. The stripping ratio (volume of overburden to volume of coal mined) varies from 3-L. The overburden and coal is mined in benches 8-12 m -(24-40ft) high; the high-wall angle is about 45 degrees. Bucket wheel and bucket chain excavators are commonly utilized for overburden and coal removal, Some of the large overburden stripping machines nave capacities. Ranging from 4400-10,000 bank cu ( 6000-14,000 BC) per hour. The overburden from the upper benches is transported around the pit using the trains and belt conveyors. It is deposited in the spoils using large stacker-conveyor systems capable of handling 2550-7300 cu m/hour (7500-10,000 cu yds/hour). The overburden from the bottom two or three benches is transported across the pit using the conveyor bridges which are computer controlled. Conveyor bridges capable of handling overburden up to 60 m (200 ft) high are currently in use; a 60 a (20e ft) high conveyor bridge has a capacity of 85 x 10 cu ( 118 x 10 cu yd) annually. The coal is loaded in the trains directly and shipped to power plants or coke oven plants.

Jan 1, 1980

By S. Zaman, John Bulter, M. E. Defoe, Franklin T. Davis

This section deals with the carbon minerals and materials: graphite, tar sands, gilsonite, and diamond. as well as sulfur and the sulfides of mercury, arsenic, antimony, and bismuth. Table I contains the production figures for each of these commodities in the United States and in the world. Specifications for concentrates are also summarized as are prices for concentrates at the time the section was written. In each chapter an attempt has teen made to describe the more common commercial mineral involved with the commodity, the processes used to recover and concentrate the minerals, as well as geographical areas where these processes are utilized.

Jan 1, 1985

By John C. Wangaard

A method of raising by use of a cage has been used with considerable success at the Cary Mine, Hurley, Wisconsin, on the Gogebic Range. The Cary Mine is owned by the Odanah Iron Company, Pickands, Mather and Company, Managers. This method is known to have been used previously at Tennessee Copper and probably in other districts. The Cary Mine was engaged in deepening the main shaft from the 34th to the 37th level. To accomplish this, and to facilitate development, a ventilation shaft 930 feet north of the main shaft was sunk from the 34th to the 37th level and crosscuts were driven on the 35th, 36th and 37th levels to the main shaft location, These levels are at 200 foot verticalintervals. All of this work was done in granite and the majority of the workings were not timbered. The next step was to get a raise through from the 37th to the 36th level, and from the 36th to the 35th level, which would later be stripped to full shaft size. Several methods of raising were considered including double-compartment cribbed and two single raises interconnected at regular intervals, but the cage method was chosen as it appeared to be a safe and efficient operation. The method in general consists in the use of a drill hole between levels through which to pass a hoisting rope to raise and lower a light cage.

Jan 1, 1958

By D. C. Willett

INTRODUCTION The Symposium on the Development of Underground Space, held in Seattle, Washington, from October 1 through 3, 1980, was organized by the "Deep Space" subcommittee of the ASCE's Underground Research Technology Council. The primary objective of the symposium was the exploration of the interfaces between the investigation, design and construction of large underground facilities in "deep space" which, for the purposes of the committee, has been defined as starting at 100m below ground surface. The meeting focussed primarily on tunnels, caverns and shafts in hard rock; the meeting format comprised a number of brief presentations concerned with the technical aspects of investigation, design and construction, followed by an open discussion, and concluded with the assembly of recommendations regarding the interface problem by the symposium participants. The principal considerations brought out during the symposium, and a general review of the conclusions, are briefly presented in the following paragraphs. INVESTIGATION The sessions dealing with "Investigation" were chaired by Dr. H. Pratt. Presentations were made by Dr. D.C. Banks, Dr. W.A. Hustrulid and Dr. Pratt. The extent of the interface of the investigation phase with the other (design and construction) phases of an underground facility will depend in large measure upon the nature of the facility; at one end of the spectrum, the investigation must be in continuous and closely coupled relationship with the design of a radwaste facility. At the other end of the spectrum, for (say) a small mining operation, the interface is largely associated with the initial development, with only minor on-going involvement.

Jan 1, 1981

By Michael V. Wolski, Ryan O. McCarter, Kenneth A. Johnson

"The Central Subway is Phase 2 of the San Francisco Municipal Transportation Agency’s (SFMTA) Third Street Light Rail project and will extend the existing Phase 1 initial operating segment from its current connection to the Embarcadero line at Fourth and King streets along Fourth Street to Market Street, under the Bay Area Rapid Transit (BART) and Muni Metro tunnels and then north beneath Stockton Street to Chinatown (Fig. 1).Total new track to be constructed as part of the Phase 2 work consists of approximately 734 m (2,410 ft) of surface track and 2,636 m (8,650 ft) of tunnels. The tunnels were constructed as twin, singletrack bores by two tunnel boring machines (TBMs) (Johnson, 2014) moving north from the southern end of the launch box under the I 80 freeway between Bryant and Harrison streets. North of Chinatown Station the TBMs continued another approximately 683 m (2,240 ft) to a retrieval shaft near Columbus Ave. at Washington Square. The project also includes five cross passages to connect the two tunnels, and three underground stations (the Yerba Buena/ Moscone Station, Union Square/Market Street Station and Chinatown Station.)Excavation of the twin tunnels was performed with two TBMs, with both TBMs driving northward from the launch box. TBM excavation was performed such that the location of the machines was staggered to separate the active excavation faces by a minimum of 91 m (300 ft) between headings. This minimum separation was maintained until the first TBM arrived at the retrieval shaft plug, at which time the separation requirement was relaxed.Excavation began with the “southbound” (SB) tunnel which will ultimately accommodate the southbound TBM light rail trains followed by the second TBM in the “northbound” (NB) tunnel. With the completion of the drives in June 2014, cross passage excavation then began and was completed in April 2015. Overall, construction of the Central Subway tunnels was a success considering the nature and complexity of the project. Additional details of the completion of the Central Subway tunnels are presented in another paper from the RETC 2015 conference (Leong et al., 2015)."

Jan 1, 2015

By R. A. * Russell, J. R. * Brooks, E. J. Griffith

In 1967, a major impoundment to contain phosphate tailings was built near Columbia, TN. Precise records were maintained on the behavior of the impoundment throughout its 20-year active life. The volume of the impoundment was determined. The DNT (dry net tons) of solids added to the impoundment were continuously measured. The rise of the mud line in the impoundment was measured monthly. The density of the settled strata was determined, as required to understand the behavior of the settled tailings. And experiments were per formed to increase the settled density of the clays. The impoundment is currently being retired and stabilized. It covers more than 400 acres and the settled muds are almost 200 ft thick. The clays have been sufficiently solidified with electroendosmosis to support the growth of cypress trees. More than three milllion trees are being planted.

Jan 1, 1992

By Terry McNulty

There are many potential pitfalls in the commercialization of innovative technology. The failures often are remembered longer than the successes, thereby serving as deterrents to subsequent attempts. The mineral industry's future depends on effective innovation. So it is essential that the causes of failure are understood. Innovation can be examined equally well in the context of geophysics, geology or mining. However the author's experience has been in mineral processing and chemical engineering. So the following discussion is limited to processes and/or plants for producing mineral concentrates, metals or inorganic chemicals. More of what follows has to do with underachievement or failure than success. But this article demonstrates that there is a strong element of predictability in the former. Furthermore, it is a credit to the minerals industry and to the engineering profession that a very high percentage of projects succeed in achieving design capacity and forecast operating costs. Innovation means the introduction of something new. In this article, the words "innovative technology" are used broadly. They include new processes and novel combinations of established unit operations, as well as novel types of processing equipment or largest-ever equipment models. The discussion of project outcomes is based on personal experience or on published information. Citations are given for technical publications that provide either project information or insights into the methodology used to analyze project performance. However, specific projects have not been identified due to the rather negative connotations of some of the conclusions drawn about the less favorable outcomes.

Jan 1, 1998

By M. Polat

Variations in flotation rate by particle size and specific gravity have been investigated for three different bituminous coals. The flotation rates for various components were determined by separating the products of bulk flotation into size-specific gravity fractions. The effects of feed size and reagent addition on the flotation response of individual size-specific gravity fractions were evaluated.

Jan 1, 1994

By Lennart Mukka

This paper describes the experiences from construction of a new ventilation system in LKABs Kiruna Mine in Sweden as well as the choice of the method for air flow regulation with concern of life cycle cost and the description of the foundation design. The evaluation of the performance test will be presented.

Jan 1, 1997

By Kenneth F. Lane

In most industries it is normal commercial policy to try to gear production to the market. In times of scarcity output is pushed to its maximum and in times of glut output is reduced. Because of the effects of supply and demand, these times correspond to times of high and low prices respectively so the policy results in maximising long run total profits. Stockpiling is often an integral part of the policy. Stocks are accumulated during depressed market conditions and sold off when demand revives. This further increases the long run total profits. However, such policies cause violent fluctuations in short term profitability and impose severe financial strains. Indeed planning and implementing the policies are a central management concern which is often critical to the success of the industry. The mining industry is no exception and, for many raw materials, trying to balance supply with demand is an international problem. Stockpiling and restricted production agreements are common elements of policy. But very little attention has been paid to the one additional control which is unique to the mining industry, namely, the cut off grade. This neglect is apparent at all levels from individual mines to national economies.

Jan 1, 1979

By F. Milton Lewis

Se resumen los métodos para preparar las estimaciones del coste de operación para un determinado proyecto minero. Se revisan los procedimientos para estimación de los costes, directos e indirectos, de operación para la explotación minera propuesta y los medios de procesamiento del mineral. Se acreditan los beneficios de los sub-productos al coste total de operación, directo más indirecto, y son deducidos para la obtención del coste de operación neto total. Se describe en detalle un método para desarrollar el coste de operación de un concentrador típico de cobre en el sudoeste.

Jan 1, 1982

By Richard Stoltz, Gary Smith

This paper presents the findings of a face ventilation investigation, conducted by the Ventilation Division, Pittsburgh Health Technology Center, at a underground coal mine operating in the Illinois No. 5 coal seam. The purpose of the investigation was to evaluate the effectiveness of a blowing face ventilation system in controlling methane liberation in the face area while mining with brattice distances up to a maximum of 40 feet from the face (extended cut). The continuous miner on this section was remotely controlled and equipped with a machine mounted dust collector. Data collected during this investigation included methane concentrations, intake and return air quantities in the face area, and scrubber air quantities. In addition, a time study was conducted to correlate the methane peaks to activities in the face area. In conjunction with the face study on Section A, separate methane liberation studies were conducted on three additional sections: B, C, and D. This was done in order to compare intake methane concentrations and methane liberations from other sections in the mine to the test section. Calculations indicated that the minimum intake air quantity necessary at the inby end of the line brattice for the section investigated was 7,000 cfm. Due to the higher intake methane concentrations and average methane face liberations measured on three other sections, the minimum air quantities necessary at the inby end of the line brattice were determined to be 13,900 cfm, 11,100 cfm, and 15,000 cfm, respectively.

Jan 1, 1991