Search Documents

By Daniel M. Flanagan

"Editor’s note: Each year, Mining Engineering features an industrial minerals review. Several people put in a fair amount of time in developing the material for this issue, all the while doing their own jobs. Thank you to the industrial minerals annual review editor, to the Industrial Minerals & Aggregates Division technical committee chair and vice chairs, and to the authors of the individual commodity profiles. Jim Norman, member SME, of Tetra Tech, is the industrial minerals annual review editor.Joe Garska, member SME, of Imerys, is chair of the Industrial Minerals &Aggregates Division’s Technical Committee.The technical committee vice chairs include:• Hyunjung Kim, member SME, of Chonbuk National University, agricultural materials.• Xihui Lin, member SME, of Kemira, ceramics and refractory materials.• Nikhil Gupta, member SME, of Virginia Tech, chemical raw materials.• Adam Rodriquez, member SME, of Penn State, construction aggregates.• LeDeana Roberts, member SME, of Imerys, fillers and pigments.• Harsha Kolla, member SME, of ChemEOR, sorbents, filters and process aids.• Edgar Blanco, member SME, of FLSmidth, specialty minerals.Their help makes possible this July industrial minerals issue. On behalf of ME readers, the editors thank them.During the past 25 years, U.S. ball clay production (the quantity sold or used by domestic producers) increased from 788 kt (869,000 st) in 1990 to an alltime high of 1.31 Mt (1.44 million st) in 2003 (Fig. 1). Housing construction within the United States, a leading market for ball clay-based ceramics and sanitaryware, began to decline in 2005, which resulted in a considerable decrease in sales of ball clay that continued through the 2008-2009 economic recession. After bottoming out at 831 kt (916,000 st) in 2009, ball clay production steadily increased through 2015 (Fig. 1). Estimated sales in 2015 were 36 percent higher than those in 1990 and 18 percent lower than those in 2003.Four companies (H.C. Spinks Clay Co., Imerys S.A., Old Hickory Clay Co., and Unimin Corp.), mined ball clay in five states during 2015. An estimated 1.7 Mt (1.18 million st) of ball clay valued at an estimated $47.5 million was sold or used by U.S. producers, a 4-percent increase from 1.03 Mt (1.14 million st) valued at $45.2 million in 2014. Approximately 65 percent of total ball clay production was air-float, 25 percent was crude or shredded and 10 percent was water-slurried"

Jul 1, 2016

By C. L. Van Dover

Organisms living at hydrothermal vents are adapted to catastrophic disturbances in their environment caused by processes such as tectonic activity and mineralization that shift the locus of fluid flux and volcanic eruptions that pave over active systems and reset the hydrothermal cycle. The scientific community appreciates this risk of natural, local loss of species, genetic, and habitat diversity. The risks of more profound loss of diversity and ecosystem function and health as a consequence of additive commercial activities in hydrothermal systems are unknown, and are not the same across all deep-sea hydrothermal systems. Vent communities differ from one ocean basin to another, as do the geological settings and geochemical dynamics of vent systems. Communities on the East Pacific Rise represent one end-member in the catalog of hydrothermal vent communities. In these systems, the life cycle of a hydrothermal field is on approximately the same time scale as the lifespan of the species that live there. From studies of the 1991 and subsequent eruptions at 9N on the East Pacific Rise, we understand the rapidity with which new vents are colonized when nearby brood stocks are available to repopulate the system. Almost instantaneously, microbial biofilms and mats form, followed quickly by invasion of mobile opportunistic organisms (especially crabs, copepods). In a matter of a few months, a predictable succession of sessile organisms recruits, grows, and reproduces. Within two to three years, the system returns to levels of species diversity that begin to match those of the pre-eruption condition. Vents on the Mid-Atlantic Ridge (MAR) represent a different end-member, with catastrophic disturbance rare relative to the life span of the organisms that make up the bulk of the biomass. We have no experience with an eruptive event or other major transformation of venting activity on the MAR and thus have no knowledge or insight regarding the time it would take for the biological diversity to return to pre-cataclysmic levels.

Jan 1, 2008

By A. Bhagwat, S. Tadolini

"Steel members of the ground support systems in underground mines are routinely exposed to corrosive environment that may range from acidic to alkaline. Corrosion of steel bolts leads to metal loss and thereby, reduction in strength and useful life. Protective coatings are commonly applied to the steel bolts to combat corrosion. However, coatings are expensive and often cumbersome in practical applications. Instead, Minova has developed an innovative technology based on sacrificial anodes. The anodes were designed from non-ferritic alloys that are inferior to steel on the Galvanic Series. This paper will present data from field testing to show significant benefit of the technology. Potential applications in current products will be discussed. INTRODUCTION Corrosion is a physical alteration of a steel material from electrochemical reaction with its environment that often results in reduction of the mechanical and physical properties of that material. Mine roof bolts, the subject of this investigation, are particularly susceptible to corrosion as they can be exposed in their working environment to ground water and air with high humidity. As other researchers have determined, corrosion increases markedly in sulfide ore bodies due to acid runoff. There are several types of corrosion that a rock bolt is likely to undergo when used for ground reinforcement in underground mines (Aziz et al., 2013). Of all the types of corrosion, pitting is particularly dangerous as it can remove capacity for the bolt to deform with subsequent strata movements. Sudden failure of a bolt is likely to occur when severe pitting corrosion is experienced. The type and nature of corrosion depend on the nature of the ground condition and bolt encapsulation. Generally, the type of corrosion and severity of the corrosion varies along the axis of bolt. Almost all of the mine roof bolts used in mines, with the exception of fiber reinforced polymers, are made from steel. The corrosion of iron is an electrochemical phenomenon with the overall equation:"

Jan 1, 2018

By F. Heivilin

If the past is the key to the future, we will have ?tough? times maintaining Industrial Mineral reserves we have and proving new reserves around our plants and in new locations. The tough times will come from resources being more difficult to find, more hoops to go thru to make them Proven or Probable reserves. As always, Industrial Minerals require competitive quality, location, and costs. Since in most cases the market has suppliers, you will have to take away customers from their present supplier. This may take years or not happen even with lower cost higher quality raw materials. To determine the finished cost for a new deposit you need to design, determine capital costs, and operating costs for a new plant . Stripping, mining, hauling, processing, and transportation costs are part of the equation. After satisfying that your costs are in line you will need to do production tests to make sure the process works on the ore. You may want to complete permitting before purchasing the property. If you are new in the business you will have to prove you can deliver the right quality, the right quantity, on time consistently year after year at lower cost to take away a customer. Without being in the market this will be hard. The cut off grades to enter a market may be much lower than sale indicates because a competitor often lowers the price to keep you out of the market. We have many more items to check before the new deposits can be put on reserves. Our old reserves will require drilling to check for new products and prove that they do not contain items that would make them unusable for our product line or cause permitting problems. Archeological checks, wetlands, more water discharge testing, county zoning, and endangered species are among many items that have been added to mine permits. There will be more. A 4-6 page mining permit becomes 30-300 pages and consists of 5-15 permits, any of which might be a fatal stumbling block. It is not guaranteed that we can mine what we have on reserves. We may fight and lose. Oil-Dri?s loss in Reno and LaPort?s in England are examples where permitting failed. The NOx, sulfur, and carbon problems are just starting. Dioxin is in the background requiring monitoring on food products to Europe. What other anions, cations, endangered species, and land types are going to be problems in the future are guesses now. What new products are we going to have to test for and cause out of balance reserves? If there are none we probably won?t be here. We are competing for land use with ?Endangered Species?, wetlands, farming, forestry, cities, roads, and hunting. We?ve mined the best quality, low overburden, easiest to mine and process raw materials. The price of land and taxes are increasing. Old royalties are 2-3 times the present acre value instead of 8-10 times the property value when leased. Land taxes are up. It was and is best that we get the land in Fee Simple Title. This isn?t always possible. However, plants are closing and people have overlooked, made mistakes in drilling or interpretation of deposits. These may be opportunities. China is eating up high quality ?Industrial Minerals ?which have caused prices to rise. We may need to change our cutoffs? in terms of smaller pit sizes and higher overburden ratios. This is money in the bank. Overburden ratios and other items increasing cutoff costs need to be rethought. Suddenly doubling cutoff ratios for overburden and decreasing pit sizes are good alternatives to looking elsewhere where we might not be able to mine for a number of reasons. The higher prices make them competitive, especially when a competitor goes out of business. However, our low overburden ratios and short hauls around our plants are not safe from new roads, condemnation by county or city governments (N. J.), zoning changes (Reno, FL., CA, and environmental regulation changes (Buffers GA, MS). New roads ?Interstates? can take reserves, increase hauling distances and reduce tons per load. Let?s combine the Refractories, fullers earth, and bentonite industries and use the last 40 years as a guide to the future looking for problems and opportunities. Some or most of the following will apply to other minerals. WHERE DO WE LOOK? First, on our own properties, those next to our properties and on properties near our competitor?s plants. Where the profit margin has increased, the distance from the plant and thickness of overburden we can use is increased. The thickness of clay is decreased. For new locations we pick the ideal location and look at deposits and closed or open operations in ever increasing distances away from that location. We need to be aware of: 1. Increased transportation costs a. Access to Roads -Backhauls b. Haul with doubles and triples c. Railroads - Loading on sidings - Ability to get switches - Cars/backhauls versus rates 2. Cost of building a new plant 3. Cost of infrastructure 4. Cost of repair or new equipment when purchasing an operating or shutdown plant. 5. Local, state, and federal mine and environmental permitting. When exploring around an established operation expect that property acquisition, drilling, mining, stripping, and hauling costs will be greater due to them having second, third, or even fourth the pick of the deposits. I found this in New Jersey looking for refractories and around Quincy, Florida looking for attapulgite. You may be able to get some better properties because the operating company has angered some land owners, their drillers missed the clay, or the property wasn?t available when they were actively exploring for reserves. You may have some product lines your

Jan 1, 2009

By Rebecca Mae Summer

Large scale surface mining has a major impact on land use. Without reclamation, abandoned mining sites are usually less productive than before mining. With increasing and completetive land use demands in the United States, it becomes increasingly evident that multiple land use should be considered for all areas that will be mined, with special emphasis on coal, sand, gravel, and stone. The mining of these commodities affects the largest land areas and the latter two are commonly mined near population centers where high land-use pressures justify serious consideration of multiple use. Typically, sequential use will mean restoration of the mined land or at least transformation of the land into a useable state. Determination of land reclamation capability is a viable approach to planning reclamation of surface mined land. The natural resource base--geology, soil, and water--controls the type and intensity of land-use practices which can be sustained following mining. Evaluating physical limitations can eliminate consideration of uses which would severely impair the environment or which are impractical. This approach provides for an environmentally and economically sound land use at very little cost. In addition, it can save or make money for the mining company and landowner. Sand and gravel is an especially significant resource because it is mined throughout the entire country and commonly extracted near cities. Increasing urban growth and industrial activity require increased supplies of sand and gravel. This translates into expanded surface mining and an increase of disrupted land. Oftentimes this land is within an urban area and has potential for real estate or water-based activities. Therefore, if reclamation is planned and carried out concurrently with mining, it is definitely feasible and

Jan 1, 1977

By Mohammad R. Jafari

The Camp Dresser & McKee (CDM)/Hatch Mott MacDonald (HMM) joint venture has been engaged by the New York City Economic Development Corporation (NYCEDC) to provide engineering ser-vices in connection with the replacement of two existing siphons which cross New York Harbor between Staten Island and Brooklyn. The project involves the construction of a 72-inch diameter pipeline within a 12-foot diameter tunnel beneath the New York Harbor. The tunnel will be constructed using either slurry or an earth pressure balanced (EPB) tunnel boring machine (TBM). This paper presents the results of an extensive geotechnical field and laboratory testing program including advanced frozen soil tests (uniaxial compressive strength tests, triaxial tests, and uniaxial creep tests), in-situ vane shear and pressure meter testing, and a marine geophysical survey (seismic reflection technique) to ascertain the complex subsurface conditions along the tunnel alignment and shaft locations. The paper will also discuss the design and construction aspects and the challenges associated with each component of this project.

Jan 1, 2008

By Michael Harris, David Mosch

The numerous small high grade gold and silver deposits of the Front Range Mineral Belt have been uneconomical because of the high costs of mill construction, transportation, and smeltering. Processing of these ores must be simple, cheap, with satisfactory recoveries, and be environmentally acceptable. Vat leach with direct electrolytic recovery satisfies these parameters. A battery of testing was conducted utilizing bottle and bucket tests. A five ton vat leach with direct electrolytic recovery gave excellent results while a five ton heap leach proved impractical due to channeling.

Jan 1, 1987

Anhydrite-based dam constructions, which have been implemented successfully in other geological formations, were investigated with regard to their suitability in salt mines. The laboratory investigations show that anhydrite-based building materials with suitable additives bind safely in spite of the high temperatures in salt mines which normally pre-vent hydration. The dependence of the compressive strength, swelling behavior, porosity and permeability upon the choice and ratio of binding material components and additives was determined. Based on the results of these investigations, a pilot-scale experiment was carried out at the GSF Research Mine Asse (Germany) using a mixture suitable for the prevailing conditions

Jan 1, 2004

By B. K. Cantrell, D. H. Carlson, W. F. Watts, K. L. Rubow

The use of diesel equipment in underground coal mines is controversial because the National Institute for Occupational Safety and Health (NIOSH) regards "whole diesel exhaust" as "a potential occupational carcinogen." Threshold limit values (TLVs) are recommended for the gaseous pollutants CO, CO2, NO, N02, SO2 and some hydrocarbons emitted in diesel exhaust. There is, however, no TLV recommended for diesel exhaust aerosols (DEA) nor is there a standard method for sampling these aerosols. The University of Minnesota and the USBM have collaborated to develop a personal diesel exhaust aerosol sampler (PDEAS) that utilizes size selective, inertial impaction and gravimetric analysis. During the field tests of this sampler, numerous air quality measurements were conducted in underground coal mines that used diesel equipment. The objective of this report is to present these data and to assess the impact of diesel face haulage equipment on mine air quality. Air quality data were collected in four underground coal mines. The mines used continuous miners and diesel haulage equipment. Daily samples were collected at the section intake, haulageway and on haulage vehicles. Both full-and partial-shift samples were collected using a variety of aerosol instruments. These included the PDEAS and the micro-orifice uniform deposit impactor (MOUDI) that sample the mine aerosol diesel exhaust fraction. Two of the mines were also monitored for the major gaseous constituents found in diesel exhaust CO, CO2, NO, NO2 and SO2. These measurements were made by either collecting bag samples for subsequent gas analysis or by Palmes dosimeters. Concentrations of CO, C02, NO, NO2 and SO2 were well below regulated levels. The mine average DEA concentration determined by the PDEAS in the haulageway for the three mines surveyed was 0.79 mg/m3, with a standard deviation of 0.19 mg/m3. DEA contributed 65% of the respirable aerosol, at this location. These results were the same as the mean DEA concentrations calculated from size distribution measurements obtained using the MOUDI. This was 0.78 mg/m3, with a standard deviation of 0.22 mg/m3.

Jan 1, 1992

By K. Pietruszka

The article presents the concept of the application of the Finite Element Method (FEM) and ABAQUS software in the global monitoring of changes in the rock mass and on the surface of the area, as a result of backfilling the workings. Waste materials applied for stabilizing old mining workings can have a strong influence on the rock mass and surface. According to the regulations, this process should be carefully monitored, especially in terms of the safety of surface structures and rock mass stability. The article presents the concept of an analytic and graphic presentation of the results of the measurements of old workings, applying the Finite Element Method and ABAQUS software in model studies. The main purpose of such interpretation of the geodetic observations results is the application of methods providing wide possibilities to present the geometry of workings, their changes and the influence of the rock mass and surface.

Jan 1, 2008

By D. D. Harbuck

The US Bureau of Mines investigated germanium and gallium extraction from an ore containing 0.089% Ge and 0.036% Ga. While previous researchers concluded that a reducing agent, such as SO2 is needed to extract germanium and gallium from such ore, this research showed that high extractions (87% Ge, 97% Ga) were possible using sulfuric acid alone, if the acid concentration were properly controlled. This control was achieved using a two-stage countercurrent leach circuit. Microprobe analyses revealed that the non-extracted germanium is in solid solution with quartz, and therefore cannot be leached with SO2 or sulfuric acid.

Jan 1, 1991

By A. G. Fabbri

This paper aims at the application of quantitative criteria for evaluating the mineral potential of square cells representing areas in terrains being explored at a reconnaissance level. The assumption is made here that the evaluation methods used by an expert economic geologist can be organized into geological models for establishing associations within imaged areas, that correspond to pixels with similar characteristics. UTM-registered multiple data sets have been constructed which include seasonal LANDSAT 2 and 4 images, SEASAT scenes, selected airborne radar images, digitized aeromagnetic, gravity, bedrock geology and topographic elevation maps. The area of interest is located in the Bathurst Inlet, District of MacKenzie, N.W.T., where a preliminary mineral potential evaluation was performed by the Geological Survey of Canada to assess its suitability for a national park. The multiple data sets described in this paper can be used for many studies at different resolutions, for comparing processing methods in remote sensing and, most importantly, for evaluating the physical and spatial relationships between the different images in registered data sets.

Jan 1, 1989

By Douglas D. Campbell, Alan S. Imrie

INTRODUCTION Mica Dam is located on the Columbia River just downstream of the "big bend" of the Columbia, where it leaves the Rocky Mountain Trench and begins to flow southwards, approximately 85 miles north of Revelstoke, B.C. (Fig.l). The dam was built as one of three Columbia River Treaty dams in British Columbia which regulate the flow of the river and provide flood control downstream in Washington and Oregon. In addition, the three Canadian dams make possible greatly increased power generation at existing power plants in the United States and further development along the Columbia and its tributaries in British Columbia. History Mica Dam, constructed during the period 1967 to 1973, is a zoned earthfill embankment 650 feet high, which has 12,000,000 acre feet of live storage and an available head of 550 feet. Power intakes which would serve either a six-unit surface or underground plant were incorporated into the design and construction of the right abutment of the dam (Fig. 2). Prior to 1971 alternative 2500 MW capacity surface and underground powerplant arrangements were studied. Cost estimates for the two alternatives were the same within the limits of estimating procedures. However, it was believed there was a certain continuing risk in locating a surface plant at the toe of a steep canyon wall. Therefore, in 1971 a tentative decision was made to proceed with an underground plant, provided that additional exploration confirmed assumptions of

Jan 1, 1976

By L. G. Kirk

The Mississippi embayment ball clay region, including western Kentucky, western Tennessee, and northwestern Mississippi, accounted for more than 95% of the total U.S. ball clay production during 1985. Other producing states during the year were Texas and Maryland. The U.S. Bureau of Mines reported total domestic production for 1985 of 910,000 short tons. The United States exports approximately 20% of the annual ball clay production. Geologically, the ball clay deposits are sedimentary in origin and occupy the north- eastern flank of the Mississippi embayment. The commercial deposits have been confined to the Claiborne and Wilcox formations within mid to lower Eocene and upper Paleocene age strata. The deposits are lenticular in nature and highly variable in areal extent and thickness. They exhibit very abrupt lateral boundaries and are bounded laterally and vertically by unconsolidated sands, silts, and waste clays.

Jan 1, 1986

By Sukumar Bandopadhyay

A present dominant problem is that of high downtime of the longwall shearer used in the coal production process. The means by which this problem can be overcome are many, but one of, the most important ones is that the-use of an expert system can reduce diagnostic and repair time. In this paper, a fault-diagnostic expert system model is presented. Specifically, the diagnostic architecture of the longwall shearer expert system and its use for diagnostic reasoning are discussed.

Jan 1, 1989

In this paper, uniaxial compression tests were conducted on intact rocks and broken rocks that were reinforced by grouting, and the effects of grouting on the strength of broken rocks were analyzed. The results show that after grouting reinforcement, the bearing capacity of broken rocks with different lithologies increased, and their uniaxial compressive strength recovered by approximately 6%–16%. The results indicated that the stronger the rock, the smaller the strength recovery of the consolidated body formed after grouting. At the same time, using borehole camera observation and deep overburden strata separations, the fracture development characteristics of surrounding rocks of the gob-side retained entry were analyzed and divided into different regions. On this basis, a guided grouting method was proposed; that is, shallow hole grouting was first used in the plastic zone of the broken surrounding rocks to form the isolation layer, and then deep grouting holes were arranged in the elastic-plastic zone of the transition zone to guide the slurry flow to the shallow unfilled zone. Therefore, the broken surrounding rocks were reinforced into an integrated body and selfbearing capacity improved.

Jul 28, 2020

GE Industrial Systems has received a multimillion dollar contract from Bucyrus International to supply complete electrical systems for three new draglines. These machines will be installed at Coal India’s Northern Coalfields’ Dudhichua and Nigahi open cast mines. The Dudhichua and Nigahi mines are located south of Varanasi. They produce Type C and Type E coal for use in the region’s super-thermal power stations. The GE systems will power and control the drag, hoist and swing motions of one Bucyrus W2000 walking dragline at Dudhichua and two a Nigahi.

Jan 1, 2000

By K. Kovári, G. Anagnostou

Slurry and EPB-shield tunnelling have been successfully applied worldwide in recent years. Under extremely unfavourable geological conditions, however, face instabilities may occur. The present paper aims at a better understanding of the mechanics of face failure. For the case of slurry shield, attention will be paid to the time-dependent effects associated with the infiltration of slurry into the ground ahead of the face. Related topics, such as the stand-up time and the effect of the excavation advance rate, will be discussed. In the case of an EPB-shield, a distinction will be drawn between fluid-pressure and effective pressure in the chamber. The effective pressure can be visualized as a “grain to grain” contact pressure between the muck and the ground at the face. The water pressure in the chamber reduces the hydraulic head gradient in the ground and, consequently, the seepage forces acting in front of the face. The face is thus stabilized both by the direct support of the pressurized muck and by the reduction of the seepage forces in the ground. The paper includes normalized diagrams which allow the assessment of tunnel face stability.

Jan 1, 1997

By Richard Newcomb

Since the report of the 1972 Rapid Excavation Conference in the city of Chicago, speculation has continued concerning the estimates of tunneling demand. Little has been published that would persuade me to modify substantially the rather tentative estimates that originated with the National Academy of Sciences-National Academy of Engineering (NAS-NAE) study of 1968 which were recomputed by the United States in the survey of the Organization for Economic Cooperation and Development (OECD) in 1970. The OECD estimates, of course, hedged the really difficult question of forecasting civil construction tunneling demands. In the United States contribution, this was done by predicting both an upper and lower bound for important categories of demand. A discounting procedure was then applied to each of the major sectors of expenditures, permitting a forecast that reflected the current subjective assessment of how extensively and how likely cities were to adopt plans that required tunneling. This was done for water, utilities, transportation and other novel underground facilities. The purpose of this paper is a modest one. In it I wish to describe the efforts made since 1972 to generate more thoughtful and more robust estimates of urban sector demands, and to apply what has been learned to the most difficult category of predictions: those for urban mass transit systems. The estimates of the Underground Construction Research Council funded by the National Science Foundation have been described at an earlier panel of this Conference. The principal effort I am familiar with is that of

Jan 1, 1974

By M. Fan, Z. Long

"This paper presents some studies on recovering valuable elements from Chinese coal by-products, including coal combustion fly ash, stone coal ash, and coal flotation tailings. Both commercialized technologies and economic potential recovery methods are described in this study. Magnetically stabilized air-dense medium fluidized bed separation, tribo-electrostatic separation, froth flotation, and hydrometallurgical methods are discussed in recovering various valuable elements in Chinese coal by-products from different coalfields. These valuable elements include iron, carbon, aluminum, rare earth elements, lithium, gallium, germanium, uranium, titanium, scandium, silicon, vanadium and phosphorus, etc. The ultimate goal is to fully utilize all valuable elements in coal by-product. Each component within coal by-product should be efficiently segregated to its highest value. INTRODUCTION Coal is mainly composed of energy-producing elements carbon and hydrogen. In addition to these elements, coal usually contains many other valuable elements, including iron, aluminum, silicon, rare earth elements, lithium, gallium, germanium, vanadium, uranium, titanium, scandium, and phosphorus, etc. These coal-associated elements are significantly enriched in coal combustion by-product fly ash because of majority of main components, carbon and hydrogen elements, being removed. Table 1 provides the chemical composition range of the main elements oxides in 12 Chinese fly ash samples collected from coal power plants located in Northeast China, Northwest China, Southwest China, and Southeast China. It can be seen from Table 1 that the major mineral components of different ashes are similar, but the bulk chemistry of different fly ashes may vary widely due to the changes of ratios of the mineral components in different coals. The major mineral components in various Chinese coal combustion fly ash are silicates, iron oxides, and unburned carbon."

Jan 1, 2017