Search Documents

By G. D. Naugle

Deep open-pit mines invariably affect the local and regional hydrologic systems. Pit dewatering, occurring during mining operations, puts an obvious hydrologic stress on these hydrologic systems. However, post-mining hydro-logic impacts resulting from the pit refilling with ground water following the cessation of mining activity can also be significant. Prediction of the rate at which the post-mining pit will fill with ground water is a critical aspect of assessing such long-term hydrologic impacts. Numerical ground-water flow modeling prov1des a method that can be used to predict the rate at which pits will fill with ground water.

Jan 1, 1992

By Takayoshi Otsuka, Taher Elsamni, Ashraf Bou-Krisha, Takaya Takimoto

"INTRODUCTION Tunnel is a closed space structure and it is necessary to ensure the sufficient time and route for safe evacuation for the tunnel users in case of a tunnel fire. In order to do so, damages and collapse of the tunnel linings and the secondary disasters can be avoided. Furthermore, the road tunnel is one of important infrastructural facilities and stopping its function for a long time for a tunnel fire could cause a great economic loss. Therefore, the tunnel structure shall be the one which can be repaired as soon as possible, and the fire protection methods need to be selected among those which enable the service to start as early as possible. The necessity of the fire protection works is evaluated for the tunnel structure with the consideration of the expensive tunnel construction cost and the economic effects of the tunnel service. Naturally, the fire protection works, which can protect the tunnel linings from the tunnel fire with small repairs, are inevitable. Design engineers of the fire protection works estimate the scale of fire from the degree of damages on the linings and its repair cost, the effect of fire extinguishers placed inside of the tunnel, the secondary disasters in accordance with the tunnel lining damages if any, and the ratio of fire protection cost calculated from tunnel operation cost. Based on this information, the engineers design the fire protection works according to the permissible limits Among the design cases of the tunnel fire protection in Japan, as shown in Table 1, there is no cases that used the fire temperature-time curve to design the fire protection works for large fire caused by vehicles catching fire. However, the most of cases used 30-60 minutes for fire duration based on the entry prohibition of dangerous goods carrying vehicles or the effect of early fire fighting. This paper will study the variation between different methods used for fire protection in road tunnel in Japan to evaluate them and try to found some recommendations. Especial l care will be attention to Polypropylenes (PP) which is starting to be applied lately."

Jan 1, 2016

By D. F. O?Connor

The health & safety of all workers in an underground environment is paramount to the success of our operations. The diesel emission reduction projects are key to improving such an environment. However, care must be taken to reduce the risk to personnel during such tests and prevent exposure to other hazards. VALE Inco works in a close partnership with its unionized employees, manufactures, suppliers, researchers and government officials to ensure projects are done safely and efficiently to successful completion. The Creighton Mine Diesel Particulate Filter (DPF) project is an example of such a project that is currently under way to evaluate new and innovative technology that will further our search for improved environment for our workplace. This paper will discuss the issues and processes that are followed to ensure Diesel Particulate Filter (DPF) field tests are conducted safely and productively.

Jan 1, 2009

The minerals industry consumes billions of dollars in raw materials, equipment, tools, services and chemicals. The industry, though, has turned overmuch of the research and development (R&D) for these products to manufacturers and suppliers. Now the industry and its suppliers must decide how much R&D the mining industry should be responsible for and what role the suppliers should play. Promoting R&D As a result of the current environment in the mining and minerals industry, there has been a substantial decrease in R&D. Depressed prices, stagnant growth, cost cutting and rationalization are evident.

Jan 1, 2000

When the 2008 Olympic Games begin in Beijing, China is September it will not only mark the end of the journey for the Olympic torch and the thou-sands of participating athletes, but the games will also mark the culmination of a massive amount of construction in the city. On display for the world to see will be 31 new and refurbished venues including the 91,000-seat National Stadium called the ?Bird?s Nest? and the aquatics center, called the Water Cube. What will not be featured as prominently on the television cameras broadcasting the games around the world will be the network of tunnels built beneath the city. But that infrastructure of rail lines will be of critical importance to the games. While preparing to host the world, China added a subway tunnel that will include four stops in the Olympic Park. The 4.4-km (2.7-mile) subway line that runs through the complex of stadiums, gymnasiums and parks began trial operations in June. Prior to the opening of that line, Beijing's No. 5 subway line, which runs through the heart of the city from north to south, opened in October. That 27.6-km (17-mile) line took nearly five years to build and includes 23

Jan 1, 2008

By A. Iordanidis

Ieropigi Fe-Ni deposit is located in northern Greece, in Kastoria?s prefecture near Albania?s borders. A laterite profile exposed by opencast mining and placed near the basement of the mine was chosen for sampling. Ten samples, representing ?pure? Fe-Ni ore, ophiolite-bedrock, ?red? ophiolite and ?enriched? ophiolite were collected, based on macroscopic observation. The samples were analysed by X-Ray powder Diffraction (XRD) for the determination of the mineral phases. Iron and Nickel concentrations of the same samples were also determined by X-Ray Fluorescence (XRF) methodology. The Fe-Ni ore samples consists predomi-nantly of hematite, goethite, chrysotile (serpentine), saponite and quartz. ?Red? ophiolite samples consists mainly of chrysotile, hematite, quartz, calcite and small amounts of paragonite and goethite. Bedrock and ?enriched ophiolite samples are comprised of chrysotile, hematite, calcite, quartz, nontronite, paragonite and sepiolite. The Fe content ranges between 13% and 49% in Fe-Ni ore samples and between 7% and 10% in ophiolite samples. The Ni content ranges between 1% and 3% in Fe-Ni ore samples and between 0.3% and 4.5% in ophiolite samples (the higher content is observed in the so-called ?enriched? ophiolite). A correlation between Fe-Ni concentrations and mineral assemblages is being attempted in order to evaluate the nickel-rich mineral phases. It is shown that the nickeliferous minerals are serpentine, hematite, goethite and saponite.

Jan 1, 2006

By P. J. Miranda, C. G. Anderson, L. G. Twidwell

Titanium is a metal of increasing worldwide strategic importance. The Center for Advanced Mineral and Metallurgical Processing (CAMP) at Montana Tech of the University of Montana is currently directing two titanium research initiatives. The first program, Titanium Extraction Mining and Process Engineering Initiative (TEMPER), is focused on producing low cost titanium through the identification and development of new mining, beneficiation and extraction technologies which will significantly reduce the cost of titanium production. This will directly benefit worldwide commercial applications. Secondly, CAMP is evaluating new technologies for fabrication of titanium utilizing the Free Form Titanium Fabrication (FFTF) initiative. These technologies may drastically reduce the cost and time to manufacture titanium components. Because of the high strength to weight ratio of titanium coupled with its superior corrosion characteristics, these programs will be of vital importance to expanding the commercial and strategic applications of titanium. An overview of these two new titanium initiatives will be presented in this paper.

Jan 1, 2005

A computer simulation of the automatic control of continuous mining machines has been prepared, similar to previous simulations of longwall mining systems and coal thickness sensors. The simulation allows for programmed variation of the horizon detection method, the azimuthal guidance system, the type and configuration of the miner, varying hardness in the unmined face material (leading to varying error in the machine heading), and the miner's cutting cycle. It simulates control of the miner in three axes. Use of the simulator makes it possible to anticipate problems arising from the complex character of underground mining, which include unpredictable multi-pass coupling and unpredictable variation in geological conditions.

Jan 1, 1993

By Dong-mei Zhang, Feng Zhang, Hong-Wei Huang, Qiang Huang, Bin Ye

"1. INTRODUCTION Nowadays, many cities around the world have constructed metro tunnels to alleviate transportation pressure from rapid urbanization. In soft soil areas, metro tunnels are usually constructed by shield-tunneling method due to its high efficiency and little disturbance to environment. However, the tunnels may show significant post-construction settlement after several years of operation. Take Shanghai Metro line 2 for example, the maximum longitudinal settlement reached 160mm after ten years of operation, shown in Figure 1. When analyzing varying factors that contribute to the long-term settlement of tunnels, the effect of cyclic loading from train vibration is rarely taken into consideration for most researches only focus on the influence of leakage problems in the tunnel while neglecting train vibration induced leakage and resulting settlement. It’s true that metro tunnels from shield-tunneling method are prone to have leakage problems due to the special structural configuration. Furthermore, trains move hundreds of times inside the tunnel every day, which inevitably will cause accumulation and dissipation of excess pore pressure. When the excess pore pressure dissipates, tunnel settlement induced by train vibration occurs(Deng F H, 2007). Although researchers (Zheng et al., 2005; Wongsaroj et al., 2007; Mair, 2008; Shin et al., 2012; Zhang et al., 2012, 2015) conducted extensive numerical analysis on the relationship between tunnel settlement and relative permeability of tunnel to surrounding soil by treating tunnels as permeable media, their attention was only paid to the tunnel settlement from reduction of hydrostatic pressure in the ground, rather than from the dissipation of excess pore pressure generated by train vibration. Therefore, the influence of train vibration on the long-term settlements of metro tunnels is still not clear."

Jan 1, 2016

By Andrew Cho, Changsoo (Kevin) Moon, Richard Flanagan, Brian Larsen

"INTRODUCTION Project Background The U.S. Army Corps of Engineers (USACE)/Port Authority of New York & New Jersey (PANYNJ), as part of their New York and New Jersey Harbor Deepening Project, will dredge this shipping channel to a depth of 16.5 m below mean low water (MLW). By deepening the channel, the new generation of larger, “post-panamax” container ships coming to U.S. waters as a result of the expansion of Panama Canal can be accommodated in local marine terminals, helping to retain the nearly 300,000 jobs and $12 billion in annual wages the PANYNJ provides to the region. The existing siphons are situated at a depth that could be compromised by the planned dredging of the channel (nycedc.com). The purpose of this project is to build a new 1.83 m diameter water main inside a 3.66m diameter tunnel replacing the two existing siphons in order to provide the necessary backup water supply to Staten Island across the Anchorage Channel within the Upper New York Bay from Brooklyn. The proposed tunnel is approximately 2.9 km long and at a depth of at least 26 m below MLW. The project is funded jointly by New York City’s Department of Environmental Protection (NYCDEP) and PANYNJ and is managed by New York City Economic Development Corporation (NYCEDC). The contractor of the project is Tully/OHL JV, the designer is CDM/HMM JV, and the CM is LiRo/PB JV. History of New York City’s Soft Ground Tunneling The New York City area has a relatively long history of soft ground tunneling, commencing in the late 19th century. Construction of the first Hudson River tunnel crossings was begun (but not completed) in 1874 for the Hudson & Manhattan Railroad using compressed air supplying a shield. The work continued intermittently until the project finally opened for service in 1907. These 1.72km long tunnels (maximum depths of 29 m) are still in operation and now operated as the PATH Tunnels. They are approximately 5.5m diameter utilizing cast iron segments. The river bed consisted of primarily silt with shallow rock near the New York side. Air “leaks” occurred during the compressed air excavations resulting in some serious “blows” with water and soil entering the tunnel, including one incident with 20 deaths."

Jan 1, 2016

By K. J. Reid, I. Iwasaki, T. Sabelin

Introduction Occurrences of platinum group minerals (PGM) in mafic and ultramafic rocks in association with Cu-Ni mineralization are well known. Yet for the Duluth Complex, a large body of dominantly mafic igneous rocks in northeastern Minnesota with significant Cu-Ni mineralization (Bonnichsen, 1972; Boucher, 1975; Watowich, 1978; Weiblen and Morey, 1980), little has been published concerning its platinum group element (PGE) contents and mineralogy. In a previous study of massive sulfide rock, sperrylite (PtAs2) was found in nickel arsenide and recovery of arsenide minerals by flotation has been investigated (Iwasaki et al., 1986; Ryan and Weiblen, 1984). Recently, an announcement was made of the discovery of significant quantities of platinum and palladium [peak assay values of 9 g/t (0.27 oz per st)] in an interval of a drill core with disseminated sulfide mineralization 16 km (10 miles) southeast of Ely, MN (Anon, 1985; Sabelin, 1985). This paper describes PGM from the Pt-Pd-enriched zone and evaluates their potential for concentration. Geologic setting The Pt-Pd zone occurs in the South Kawishiwi in¬trusion near its basal contact at 734 to 737 m (2408 to 2418 ft) depth. The South Kawishiwi is one of several minor mafic intrusions that constitute the western margin of the Duluth Complex near Ely, MN (Fig. 1). It is com¬prised of a 70.1- to 350.5-m (230- to 1150-ft) thick sul¬fide-bearing basal unit of troctolite with minor amounts of anorthosite, norite, picrite, and oxide layers overlain by a troctolite unit with interlayered anorthosite (Bonnichsen et al., 1980; Foose, 1984; and Foose and Weiblen, 1986). The basal unit, in which the Pt-Pd zone is found, is markedly heterogeneous in rock type, lacking any coherent internal stratigraphy, and shows evidence of both pre- and post-consolidation faulting (Foose and Weiblen, 1986). Geochemistry Chemical analyses were made on 0.3-m (1-ft) intervals of crushed drill core material (1/4 core, BX size) at 731.5 to 740.7 m (2400 to 2430 ft) depth and the results are presented in Fig. 2. The analytical techniques used were atomic absorption spectrometry for silver, chromium, copper, and nickel; a coulometric titration method for sulfur; and a combined fire assay-DC plasma technique for gold, palladium, and platinum. Figure 2 shows the significant enrichment of platinum and palladium at 734 to 737 m (2408 to 2418 ft) depth; it corresponds to a stratigraphic interval rich in oxide minerals. Average values for platinum and palladium contents over the 3-m (10-ft) interval are 2520 and 2580 ppb, respectively, or 5.1 g/t (0.15 oz per st) platinum plus palladium. Platinum plus palladium contents from individual 0.3-m (1-ft) intervals are as high as 9120 ppb or 9.1 g/t (0.27 oz per st) and average 7.4 g/t (0.22 oz per st) in a 1.5-m (5-ft) interval in the richest part of the zone. The Pt-to-Pd ratio is nearly 1:1 over the entire 9.1-m (30-ft) interval and the platinum and palladium correlate closely with chromium, which ranges from 1.9% to 5.3%. Copper, nickel, and sulfur contents for the drill core interval are also given in Fig. 2. In¬terestingly, the Pt-Pd high corresponds to a depletion in copper, nickel, and sulfur. Mineralogy of the Pt-Pd zone The Pt-Pd zone occurs within an oxide-rich zone or layer that consists essentially of oxide minerals, plagioclase, and olivine. The oxides may constitute as

Jan 1, 1987

By William M. Warren

Recent sinkhole activity in carbonate terranes of Alabama has resulted in damage to transportation lines, structures, utility lines, and property in general. Active sinkhole development and subsidence has been well documented in Alabama, Florida, Pennsylvania, and South Africa. An excellent example of the potential danger resulting from this activity is the spectacular collapse under a South African gold ore crusher plant that resulted in the death of 29 men in 1962. Due to the severity of the problem in certain localized areas in Alabama, a detailed investigation is being undertaken by the Geological Survey of Alabama and the U. S. Geological Survey. One of the most promising techniques is the application of aerial photography and thermal infrared imagery. Conventional and modern remote-sensing techniques are being used in Alabama to locate and define areas of sinkhole activity and to determine which areas are most prone to its occurrence.

Jan 1, 1975

By N. K. Dumakor-Dupey, K. J. Bansah

"We made site visits to determine potential environmental issues caused by artisanal and small-scale mining (ASM) in the Tarkwa Mining Area (TMA) of Ghana. Activities of the diggers were observed to degrade vegetation, land and water. Improper handling of mercury was also identified as a major threat to people and ecosystem. Large abandoned pits and trenches posed fall traps to farmers, hunters and wildlife. We argue that lack of adequate monitoring and regulatory enforcement by Ghanaian authorities, together with inappropriate mining processes, probably due to lack of technical expertise are contributing factors to the environmental issues of artisanal and small-scale mining in the TMA. INTRODUCTION Environmental degradation caused by artisanal and small-scale mining (ASM) has been a major concern to many people and governments around the world. ASM is often associated with health, safety and environmental issues in communities where it is practiced (Kitula, 2006; Asiedu, 2013; Sousa et al., 2010). Some of the environmental issues that have been reported include land degradation, mercury contamination, cyanide release, and pollution of rivers/streams. These issues have been attributed to improper mining methods, inefficient technology, lack of technical training and environmental awareness, and lack of regulatory enforcement (Serfor-Armah et al., 2005; Bansah et al., 2016a; Hentschel et al., 2002). In Ghana, ASM typically occurs in rural communities, providing jobs to many people and contributing towards socioeconomic growth of the country (Banchirigah & Hilson, 2010; Bansah et al., 2016b; Osei-Kojo & Andrews, 2016). As a result of the environmental issues, many people have called on government to develop drastic measures to control ASM operations. It is in this regard that this paper examines potential environmental issues caused by ASM in the Tarkwa Mining Area in Ghana, and suggests mitigation measures to ensure environmental sustainability. ASM in the area comprises of registered (licensed) and unregistered (unlicensed) operations that adopt surface or underground mining methods to exploit gold-bearing materials. Surface operations typically involve clearing of vegetation, removal of overburden, excavation of mineral deposit, washing/grinding of excavated gravels and processing with mercury. Except grinding, washing and mercury recovery, underground operations are conducted below ground with limited impact on the surface. Alluvial mining is also commonly practiced in streams and along river banks. These activities can have devastating impact on biodiversity of the ecosystem. To achieve the objective for this study, field visits were made to ASM sites to observe operations and interact with diggers. Visits were also made to host communities of ASM and government officials to obtain their perspectives on ASM in relation to environmental impact. The study area (Tarkwa Mining Area) is located in the Western Region of Ghana (see Figure 1). It is endowed with natural resources such as gold and manganese. Hence, mining is the major economic activity in the area. ASM is widespread, with 15 registered operations and several unregistered mines. The environmental issues observed in the study have been grouped into three main categories: vegetation and land depletion; water quality and pollution issues; and mercury contamination issues."

Jan 1, 2017

By M. Argiantopoulou

In today?s mining environment, improving production, performance, productivity and profitability is crucial. Production, ancillary, plant and shipping equipment need to be monitored and controlled by online systems delivering production statistics and real-time information to everyone involved, including equipment operators. Traditional systems currently in use today, operate in an iterative mode constantly switching between scheduling and execution. However, the real world tends to change in ways that invalidate such advance schedules. Agent based computing has been hailed as the most significant breakthrough in software development and the new revolution in software. Agent systems are being used in an increasingly wide variety of applications, including complex mission critical systems such as Air Traffic Control. This paper presents the possible ways that multi-agent systems can be applied to mine production and rehabilitation scheduling problems with focus on real time fleet management, plant and equipment performance monitoring, downtime and delay reporting, stockpile management, personnel and equipment tracking and product distribution and transportation.

Jan 1, 2006

By W. R. Reed, G. J. Joy, B. Kendall, A. Bailey

"Testing of the NIOSH-designed roof bolter canopy air curtain (CAC) has gone through many iterations demonstrating successful dust control performance under controlled conditions. J.H. Fletcher & Co. (Fletcher), an original equipment manufacturer of mining equipment, has further developed the CAC concept by incorporating it into the design of its roof bolting machines. A new CAC design has been developed incorporating the results of testing of the NIOSH design and the recent Fletcher design. Observations from smoke testing conducted on this new CAC design in a laboratory setting show promise for improved performance. INTRODUCTION Exposure to respirable coal mine dust can cause coal workers’ pneumoconiosis (CWP) otherwise known as black lung. If silica is present in the dust, the miner may develop silicosis in addition to CWP. CWP and silicosis are occupational respiratory diseases that are ultimately fatal and have no cure. The only method of prevention is through elimination of exposure to respirable coal mine dust and crystalline silica (quartz). The current occupational exposure limit (on an MRE basis) for respirable coal mine dust is 2.0 mg/m3 during each shift that a miner is exposed in the active workings of the mine or in mine facilities [30 CFR 70.100 2015]. Recently enacted legislation changes this standard beginning in August 2016 to 1.5 mg/m3 for a full working shift [Federal Register, 2014]. If the respirable coal mine dust contains more than 5% silica, the applicable respirable dust standard is reduced; calculated as 10 divided by the percent quartz present [30 CFR 70.101] so that the effective exposure limit for respirable quartz is 0.1 mg/m3 for a full working shift. Sources of exposure to respirable coal mine dust for the roof bolting occupations include infrequent maintenance and cleaning of the vacuum dust collection system and operating the bolter downwind (in the return air) of the continuous miner [Goodman and Organiscak, 2003]. Recent studies have demonstrated that vacuum dust collection systems are effective in capturing bolter-generated dust, if maintained and operated correctly and if proper face ventilation techniques are used. However, most exposure to respirable coal mine dust for the roof bolter occurs when the roof bolter machine is operated downwind of the continuous miner [Potts et al., 2011; Colinet et al., 2013]. Because of this higher exposure downwind of the continuous miner, the roof bolter is generally limited to working downwind of the miner only once during a production shift"

Jan 1, 2016

By Daniel H. Knepper

Estimating the lithologic composition of gravel deposits for aggregate quality using standard field and laboratory techniques is costly and time-consuming. As an alternative, digital geologic maps and elevation models may provide a means for predicting the lithologic composition of channel and terrace deposits. Digital geologic maps can be used to evaluate the distribution of map units: their geomorphic setting, and the physical properties of the gravel source. To test this concept, the lithologies and topography of the upper drainage basin of the Big Thompson River along the Colorado Front Range were used to examine various factors that may control the final lithologic composition of channel and terrace gravels downstream. The simplest factor is the area of each of the map units in the upper drainage basin area, which can be easily measured from the digital geologic map. The percentage of each map unit within the total area provides a estimate of the pro- portions of each map unit that might be expected to occur in the downstream gravels. Published estimates of the hardness and durability of each map unit were used to calculate physical property-weighted areas; these areas are an estimate of the potential of each unit to be eroded and transported as gravel-sized particles. The areas of each map unit at 1-kilometer intervals from the drainage basin exit point were used to calculate a distance-weighted area for each map unit. For this study, a simple inverse relationship (area/distance) was used for distance weighting, but a more complicated distance function may ultimately be required. The topographic setting of exposed rock units should exert a significant influence on whether material will move slowly or rapidly through the drainage system. Two topographic factors were examined: gradient and slope. A simple gradient between map unit occurrences and the exit point of the drainage basin was used to calculate a gradient-weighted area estimate for each map unit. The slope-weighted area estimate uses the slope steepness (in degrees) in the immediate vicinity of each map unit occurrence as a measure of the tendency of material to begin moving into the sediment transport system. The primary intent of this study was to test the concept of using digital geologic map and elevation images to estimate gravel composition, rather than actually producing a useful analysis of a drainage basin. Each of the controlling factors was examined independently to gain an understanding of the magnitude of the effect of each factor. Ultimately, a comprehensive predictive model will be constructed using a combination of the various controlling factors.

Jan 1, 2001

By T. Gupta, T. Ghosh

"Rare Earth Elements (REEs) and their compounds are essential for numerous modern high tech applications such as renewable energy technologies, catalysts and defense applications. The destabilization of REE pricing owing to the global demand and supply deficit has forced many countries to re-evaluate the possibility of indigenous production of REEs. Cost effective and eco-friendly opportunities are being widely explored for extraction of REEs from non-conventional mineral sources such as coal and coal byproducts to stabilize the supply chain. Coal from Central Alaska (Healy Coal Mine) and Southern Alaska-Cook Inlet (Wishbone Hill) province have been found to possess elevated REE concentrations as compared to average world coal estimates. The objective of the study is to enrich the REEs in the fine size fraction (-75 Microns) from Healy and Wishbone Hill by froth flotation technique. A Box-Behnken design was applied for modeling and optimization of some operating variables on the flotation to maximize REE enrichment. The variables studies were frother dosage, pulp density (% Solids) and collector dosage. Experiments were carried out using a statistical design and the main and interaction effects on response variable was evaluated by analyzing 3D response surfaces. Based on the experimental results the optimum flotation conditions for maximum REE enrichment in the froth fraction was obtained at 4.2% Solids and 32.7 ppm of frother dosage for Healy coal sample and 10% Solids and 37.9 ppm of frother dosage for Wishbone Hill coal sample. The quadratic equation for modelling and optimizing the response variable is found to be independent of collector dosage for both the coal samples. INTRODUCTION Alaskan coal deposits are distributed in three major coal provinces and are in Cretaceous and Tertiary rocks. The climate, vegetation type and sedimentation process has attributed to low sulfur content (averaging 0.3 percent) in Alaskan coals compared to other coal deposits found across the globe. In Central Alaska-Nenana and Southern Alaska-Cook Inlet coal province coal resources are contained in Tertiary rocks while bulk of the Coal resource in North Slope coal province is contained in Cretaceous and Tertiary coal bearing rocks [1]. Coals from Central Alaska- Nenana (Healy) and Southern Alaska-Cook Inlet province (Wishbone Hill) have been found to possess elevated concentrations of critical REEs as compared to the amounts present in world coals (Figure 1). The Wishbone Hill deposit is considered a relatively small deposit, with about 14 million tons of identified reserves, compared to Healy which has over 500 million tons identified [2]. The REE concentrations up to 286 ppm and 524 ppm on ash basis have been reported by Gupta et al. in 2016 with elevated concentrations Ce, La, Y and Nd which are expressed to be of critical importance by US Department of Energy. Accordingly, the two coal samples possess the potential to be used as a REE resource in the near future under favorable socio-economic and geo-political scenarios. [3, 4]"

Jan 1, 2017

By Everett M. (Original by) White

Numerous articles have been written about the coal mine ; he has been compared with brave men who have gone out to conquer some unknown hazard throughout the ages. Now, however, modern mining is no longer something to be avoided, but a vocation that anyone can be proud of, with remuneration equal to or above that of almost any industry. A concerted effort is being made each day by both the operators of most mines as well as the state and federal inspectors to see that coal mines are as safe or safer than work places in any other industry. How- ever, it is true that mine fires and explosions have occurred in the mining industry since its inception. One of the earliest accurate references to such an occurrence is found in the transactions of the Royal Society of London. In the Colliery Managers' Handbook, 1898, Caleb Pamely writes of an explosion that occurred at Fatfield, England in August 1708, resulting in the deaths of 69 persons. He states: "Three of them, viz, two men and a woman, were blown quite up from the bottom of the shaft, fifty-seven fathoms deep, into the air, to a considerable distance from the mouth of the pit." It is interesting to note that women were employed as miners in England during that period. In the United States, the first record of coal mined was in 1702 by the Jamestown colonists. In 1786, about 20 years after Pittsburgh, PA was first settled, a charter was granted by William Penn to mine coal on the banks of the Monongahela River. Then in 1803, the first important coal company, the Lehigh Coal Co., was established. From this beginning, the mining industry continued to grow in importance and the first state mining law was formulated in 1870. The Pennsylvania state mining law was followed in 1873 by Ohio's, and in 1876 by Maryland's. A mine explosion at Avondale, PA in 1869 stimulated state legislatures to formulate these early laws. In 1907 near the town of Fairmont, WV, there were, within three days, two explosions resulting in a total of 597 deaths. Because of this, the federal government took action and by 1910, the US Bureau of Mines had been established. This was perhaps the most significant change in health and safety for miners during the first half of the 20th century as the USBM concentrated its entire efforts in the study, research, and testing of methods totally directed towards improvement of the health and safety of the miner. After a mine disaster in Illinois, a federal law was passed in 1940 calling for federal coal mine inspectors. Then in 1969, Congress enacted the Federal Coal Mine Health and Safety Act following a mine explosion near Farmington, WV. In 1977, the law was revised and included noncoal mining operations.

Jan 1, 1981

By P. V. R. Bhaskar Sarma, P. K. Sahoo, G. Roy Chaudhury

A process was developed to treat an ammoniacal leach liquor containing zinc using Di (2-ethyl hexyl) phosphoric acid (D2EHPA) as the extractant. The objective of this work was to develop a process package for the treatment of complex sulfide leach liquors. Zinc extraction could not be carried out directly from the ammoniacal solution in mixer-settler units because of crud formation and low extraction efficiency. After neutralizing the free ammonia with H2SO4, the extraction efficiency was only about 40%, due to the high concentration of (NH4)2SO4. To decrease the (NH4)2SO4 concentration, the free NH3 was steam stripped, and the resultant liquor was subjected to zinc solvent extraction. An extraction efficiency of 98% could be achieved by controlling the equilibrium pH. Stripping studies were also optimized after removing ammonia from the zinc-loaded organic. A continuous 100-hr operation that included extraction, scrubbing and stripping, was carried out successfully.

Jan 1, 1995

By K. L. Gabby

Since mercury is chemically similar to silver, it tends to dissolve along with the silver and gold during cyanide leaching. Ultimately mercury is recovered along with the silver as mercury/silver/gold amalgam which requires retorting to remove the mercury prior to refining the silver and gold. A possible approach to separating mercury from silver and gold in cyanide leach solutions is to take advantage of the replacement reaction between [Hg(CN)4]2- and Ag2S, which results in precipitation of mercury as HgS while dissolving silver as [Ag(CN)2]-. Results are presented demonstrating that mercury can be removed from cyanide solutions with high effectiveness, while, at the same time, recovering additional silver in solution. Initial experiments with static flasks in the laboratory showed a high degree of mercury removal could be achieved. Results using actual metallurgical plant products in bottle roll tests indicate the process works on a larger scale, but also results in significant gold losses if the solution being treated has high gold levels, such as carbon stripping pregnant eluent solution.

Feb 23, 2014