Search Documents

By Haydn H. Murray

The term clay is somewhat ambiguous unless specifically defined, because it is used in three ways: 1) as a diverse group of fine-grained minerals, 2) as a rock term, and 3) as a particle size term. As a rock term, clay is difficult to define because of the wide variety of materials that comprise it; therefore, the definition must be general. Clay is a natural, earthy, fine grained material comprised largely of a group of crystalline minerals known as the clay minerals. These minerals are hydrous silicates comprised mainly of silica, alumina, and water. Several of these minerals also contain appreciable quantities of iron, alkalies, and alkaline earths. Many definitions state that a clay is plastic when wet. Most clay materials do have this property, but some clays are not plastic, e.g., halloysite and flint clay. As a particle size term, clay is used for the category that includes the smallest particles. The maximum size particles in the clay size grade are defined differently on various grade scales. Soil investigators and mineralogists generally use 2 pm. as the maximum size, whereas the widely used scale by Wentworth (1922) defines clay as material finer than approximately 4 pm. Some authorities find it convenient to use the term clay for any fine-grained, natural, earthy, argillaceous material (Grim, 1968). When used this way, the term includes clay, shale, or argillite, and some argillaceous soils. Even though no standard definition of the term clay is accepted by geologists, agronomists, engineers, and others, the term is generally understood by those who use it. Clay is an abundant natural raw material, and it has an amazing variety of uses and properties which will be discussed in this chapter. Clays rank among the leading industrial minerals in both tonnages produced and total value. Their importance is indicated in Table 1, which lists the 1988, 1989, and 1990 productions according to the US Bureau of Mines (Ampian, 1992). As industrial minerals, clays are a complex group that consists of several mineral commodities, each having somewhat different mineralogy, geologic occurrence, technology, and uses. In this section these commodities are organized as follows: 1) bentonite, 2) common clay, 3) hormites, and 4) kaolin. Fuller's earth is discussed in both the bentonite and hormite chapters. Fuller's earth is a term based on use, and both bentonites and hormites are sold as fuller's earth. The overlapping is particularly evident where both bentonite and non-bentonite fuller's earth are used for the same purposes or products, such as in drilling mud, bleaching or clarifying fats and oils, and carriers for insecticides and fertilizers. Kaolin, ball clay, halloysite, and refractory clays are grouped together because they consist mainly of minerals of the kaolin group. Common clay is a grouping of several fine-grained materials, including shale, sometimes referred to as miscellaneous clay. The scientific and technological publications pertaining to clays

Jan 1, 1994

By S. D. Abbott

Mines are filled with a mixture of gases, some of which are toxic, flammable, or explosive. Others serve as early reporters of impending problems. Mines monitor these gases in order to ensure the safe, efficient operation of the facility and avoid losses or disasters. Two different approaches to monitor these gases have historically been taken. One kind of device measures the amount of each gas present by using selective detectors (e.g. handhelds and spectrometers). Another kind separates the mixture of gases into the individual constituents, then measures the amount of each gas present (e.g. gas chromatographs). Handheld units are the most widely used, but gas chromatographs are the most powerful yet underutilized units available to enhance mining operations. There are many misconceptions about the nature, applicability and proper use of each type of device, and little data is available. Up to this point, many people had only the manufacturers? claims to guide them. This study was undertaken to clarify the range of applicability, important characteristics, and value in use of these units in real-world situations. An additional goal of the study was to provide ways to evaluate comparative data, and thus aid mining operations in choosing the most beneficial and reasonable ways to use such devices in various situations and contexts.

Feb 23, 2014

By A. J. Kwitowski

Remote control for mining machines ordinarily means the operator is not seated on the machine, but is located within direct view of the machine and work area Thus, remote control operators are exposed to the hazards of roof/rib falls and dust/methane explosions. The U.S. Bureau of Mines has developed a method to disassociate remote operators from these hazards. Off-board, computer-based "tele-operational" systems are utilized that station the operators one-hundred meters or more distant from the working faces. Details are provided for tele-operated systems for thin-seam extraction and haulage equipment in highwall and deep, room-and-pillar coal mines.

Jan 1, 1992

By Jerome F. Thomas

The primary purpose of this paper is to review the fire and explosion hazards associated with hydrocarbons heavier than methane. Methane is the classical hydrocarbon encountered in mines whose presence is generally due to bacterial decomposition of organic debris. The higher hydrocarbons are more likely to be found during tunneling when petroleum products either natural or man made are encountered. Fires may be defined as rapid gas phase oxidations accompanied by the rapid evolution of light and heat. Explosions may be defined as uncontrolled fires. The rapidly expanding gases resulting from combustion exceed the speed of sound and generate percussive forces. The essential elements for a fire or explosion are shown on Figure 12: (1) a gas phase explosive mixture and (2) an ignition source. The paper will attempt to review various aspects relative to the explosive mixture; The concentration and composition; Techniques for detection; Techniques for ventilation to reduce concentration below explosive limits. The ignition sources are also listed on Figure 12. An arc originates from an electrical source such as electrical switches, relays and motor brushes. Static electricity can also be an arc source and may be generated by air flowing through rubber bases or a rapidly moving endless belt. A spark is generally associated with abrasion of iron metal. A flame source may be a match, candle. cutting or welding torch, or engine exhaust. If

Jan 1, 1974

By J. P. McDonnell, L. A. Beckett, K. Y. Hammy

Dangerously high stress areas can be controlled by proper mine planning and/or destressing. This paper reviews practical methods to detect and destress high-stress zones along coal faces. The US Bureau of Mines investigated stress-related burst problems and destressing efforts at a cooperating mine. Laboratory tests of the drilling yield method for high stress detection were conducted to determine the correlation between the volume of cuttings obtained and the magnitude of the applied stress. A three- dimemiom1 computer modeling program was used to evaluate the effectiveness of stress relief methods.

Jan 1, 1987

By J. R. England, W. J. Taylor

The Sudbury Basin is the scene of the mining operations of the Ontario Division of the International Nickel Company of Canada, Limited. Around the rim of the geological formation and within thirty miles of the City of Sudbury are located twelve operating mines and one open pit operated by the Company. The City, with a metropolitan population of some 100,000 lies 240 miles Northwest of Toronto. In addition, there is one mine in Northwestern Ontario, at Shebandowan, 700 miles Northwest of Sudbury. In 1973 these mines produced 16.5 million short tons of ore of which 14.9 million tons were from underground and the balance from open pit operations. Mining methods include blasthole, sublevel caving, induced caving, shrinkage, cut-and-fill and undercut-and-fill. Raise boring commenced at Inco in 1964 and is now applied at all mines in the Sudbury District (Figure 1). [ ]

Jan 1, 1974

By N. N. Manu

In the Central African Copper Belt, sulfidization flotation is the standard practice for dolomitic copper oxide ores. It is a delicate process, and its plant application requires close control of the reagent addition. This paper presents the results of a thorough laboratory investigation. It features the monitoring, during sulfidization, of the pulp pH, the residual sulfide ion concentration and redox potential. Variables examined during the process were: retention times, sulfidizer additions, pH, collector type, dispersant dosage and reducing agent addition. Implications of the findings for plant application and process control are also briefly examined.

Jan 1, 1994

By I. González, G. Lapidus, M. Teutli

The cementation kinetics of silver with aluminum particles were studied with model solutions under nitrogen atmosphere, varying the temperature, aluminum/silver ratio, pH and concentrations of thiourea and surface activator Recoveries were evaluated both by solution concentrations and by REDOX measurements. Tafel curves were determined for this system. The results showed the cementation process to be essentially independent of the pH and thiourea concentration. However, a strong influence was observed with respect to temperature, aluminum/silver ratio and the quantity of activator. There is evidence that the controlling step is the dissolution of aluminum oxide from the particle surface.

Jan 1, 1990

By [Miroslaw] M. Hajdasinsk

The identification of the real internal rates of return (IRR's) of a project is essential for its economic evaluation. The existing methods for the calculation of IRR's are both cumbersome and unreliable, mainly because of their inability to effectively isolate the real IRR's and incapability of discovering multiple IRR's of even multiplicity. In this paper, a concept of the 'cash flow pattern tree used for isolation of the real IRR's of a project is presented. This concept, combined with the Sturm procedure for counting the real distinct zeros of a polynomial within a specified interval, leads to the development of a method and computer program for isolation and calculation of the real IRR's of a project. The method examines whether or not real IRR's exist, and if they do, isolates them within bounded and narrow intervals in a mathematically founded way. The isolated IRR's, whether simple or multiple, are subsequently calculated either directly or by means of an appropriate approximation procedure. Numerical examples assist the development of the method and the corresponding computer algorithm. Because any Net Present Value treated as a function of interest rate can easily be transformed into a polynomial, the method presented also constitutes a method for finding the real zeros of a polynomial.

Jan 1, 1986

By Noel C. Joughin, Orrie Fenn, Brian E. Protheroe

Work has shown that the use of high-pressure water jets enhances the performance of mechanical cutting in very hard rock. To assess the potential of this approach for use in conjunction with free rolling cutters, a series of tests has been conducted using both disc and button type cutters, to determine the relative effects, on cutter performance, of variations in relevant jet and cutting parameters. In these tests it was found that water jet assistance can result in reductions in the forces on a free rolling cutter typically of the order of 40%.

Jan 1, 1985

By Tommy B. Thompson

The Cripple Creek diatreme-intrusive complex is known primarily for its vein telluride-gold ores. It is also known for the great vertical range of its major veins - >990 m (>3250 ft). Not as well-documented, however, are the ores dispersed into the wallrocks adjacent to veins, the ores associated with hydrothermal and tectonic breccias, or mineralized zones within fluvial, lacustrine and volcaniclastic rocks de- posited within the diatreme complex. The ore-gangue minerals were precipitated from oxidized, alkaline fluids that yielded an abundance of carbonate, sulfate and oxide minerals along with minor base metal sulfides and precious metal tellurides. Wallrock alteration is limited adjacent to veins and is more extensive within hydrothermal and tectonic breccias. Cripple Creek background The Cripple Creek district has a spectacular production history. More than 653 t (21 million oz) of gold were recovered between 1891 and 1959. Early published accounts documented the principal production from narrow- sheeted vein systems (Cross and Penrose, 1895; Lindgren and Ransome, 1906; Loughlin, 1927; Loughlin and Koschmann, 1935). Production also came from spectacular open-space fillings within the Cresson diatreme, also known as the Cresson “blow-out” (Patton, 1917; Patton and Wolf, 1915). Beginning in the mid- l96Os, more modern studies were initiated by the US Geological Survey (USGS) (Gott et al. , 1967, 1969; Kleinkopf et al., 1970) and by universities (Lane, 1976: Dwelley, 1984; Trippel, 1985; Thompson et al., 1985; Saunders, 1986; Birmingham, 1987; Eriksson, 1987; Nelson, 1989; Wood, 1990; Seibel, 1991).

Jan 1, 1992

By A. J. Kwitowski

Remote control is usually associated with deep mine, continuous mining machines. This is because thin-seam operation precludes an onboard operator's compartment or the mine has approval to conduct extended cut mining. Using a tethered or radio-linked control box, the remote operator is typically situated 3 to 15 m (10 to 50 ft) from the working face. The operator receives direct operational cues through senses like vision, hearing and feel. Remote control is sometimes touted as a safety feature. However, this is not always true, as operators are not provided protection from roof and rib falls or being crushed between the machine and a rib. Remote control operators are also left exposed to dust and noise. Teleoperation described here is the computer-based, distant control of mining machinery from a protected operator compartment located out of the line-of-sight from the operational site. Video, sound and other sensory information are gathered through sensors and electronically transmitted to and displayed at the operator's location. The teleoperator responds to the information and makes decisions that are initiated by control devices (usually switches). These control commands are then electronically transmitted to the re¬mote machinery and the appropriate machine function(s) are carried out. Teleoperation increases the safety of mining machine operators as it removes them from the immediate vicinity of hazards. The US Bureau of Mines' involvement with teleoperation dates back to 1979. Following feasibility studies, a highwall milling system (HMS) was developed and tested. A deep, thin-seam, room-and-pillar system (TSRPS) has been designed and is currently being surface tested.

Jan 1, 1992

Tables

Jan 1, 1973

By Z. C. Liu, F. F. Roxborough, Lin. B. B.

The size distribution of coal cut by a mining machine is an important performance factor. It is well established that the main machine system variable that affects product size is the depth of cut. In essence, the greater the amount of coal won by a machine cutting at shallow depths, the greater the proportion of dust and fines produced. Conversely, deep cuts produce less dust and a generally larger product size. When cutting with a rotating drum, as well as with a longwall shearer, the depth of cut always varies from zero in the vicinity of the roof and floor, where most of the dust and fines are produced, to a maximum at mid-drum level. In this paper, minimizing the amount of shallow cutting with a cutting drum is discussed, and the effects of the drum cutting and design parameters on cross-sectional cutting area per revolution are analyzed. This study shows the following: •more shallow cutting occurs during the entry quadrant of a cutting cycle than during pick exit; •the ratio of the projected area of shallow cutting to the total projected area of cutting by a single pick per drum revolution is virtually the same for drums of different radii (however, it decreases as the maximum depth of cut increases); and •for double drums, the use of unequal drum diameters can reduce the production of dust and fines, compared to using drums of the same diameter.

Jan 1, 1998

By S. K. Mishra, S. B. Kanungo, D. Biswal

Jigging of the -2.8 +0.7-mm size fraction of a friable, low-grade manganese ore sample from Andhra Pradesh increased the Mn content of a concentrate by 7% to 8%, with an average recovery of 57%. The jig concentrate was mixed with the unjigged -0.7-mm size fraction and ground to -150 µm. The sample was then subjected to wet high-intensity magnetic separation (WHIMS). The magnetic fraction thus obtained showed an increase in Mn content of 6%, but with an overall recovery of only 50%. The results of hydrocyclone classification of -150- µm ground ore indicated that the method is not capable of upgrading the manganese content, as both ferromanganese oxides and aluminosilicate gangue minerals constitute the fine size fraction. However, when the nonmagnetic fraction obtained from the WHIMS of -150- µm ore is subjected to hydrocyclone classification and the underflow obtained is subjected to WHIMS again, an overall recovery of about 50% to 52% is obtained with at least a 7% to 8% increase in the Mn content of the product. The phosphorus content in the product is not reduced by either of the two combinations of methods. The complex association of phosphorus with all the major phases in the ore has been clearly demonstrated from the linear correlation between the distribution ratios of major constituent phases and phosphorus.

Jan 1, 2000

By Richard H. T. Garnett

In 1900, placer gold was discovered on the beach of Nome, AK on the southern coastline of Alaska's Seward Peninsula (Garnett, 1991). The site is about 800 km (500 miles) from Anchorage. Nome is connected to Anchorage only by air (daily) and by sea (summer). Total onshore placer gold production from Nome's immediate vicinity was more than 155.5 t (5 million oz). Alaska Gold Co, has continued to produce gold onshore with, until recently, two bucketladder dredges, each of 255-L (9-cu ft) bucket capacity. Small-scale marine dredging for gold has been at- tempted several times this century (Garnett, 1991). Western Gold Exploration and Mining Co. Ltd. Partnership (WestGold) is the only company to have been successful in achieving a significant offshore production. The Nome bucketladder-dredging operation from 1986 to 1990 constituted a unique marine-mining experience in the United States. \Inspiration Gold Inc., WestGold's predecessor, acquired six offshore leases in 1985. The total lease area of 87 km2 (21,551 acres) extended from the coastline to the 4.8-km (3-mile) offshore limit (Fig. 1). Those leases al- ready had been partially explored. Drilling was conducted off the shorefast winter sea ice. Therefore, it was rarely more than 1.6 km (1 mile) from the shore or in water deeper than about 9 m (30 ft). In 1985, estimated reserves comprised of a 5-m (17-ft) vertical thickness of sediments below 6.3 m (20 ft) of water. This meant a mean digging depth below the mean sea level (msl) of 11.3 m (37 ft). It was thought that the offshore Nome deposit possessed a feature that is common with many terrestrial gold placers - the secret of profitable exploitation of the marine deposit lay in maximizing the dredge throughput to minimize the unit costs. The inability of the project to withstand the prohibitively high cost of a new dredge was recognized. So Inspiration Gold purchased a used unit. This was the world's largest ocean- going bucketladder dredge (Fig. 2). Binzn was an 850-L (30 cu ft) bucket capacity dredge that was lying idle in Singapore. Originally constructed in the Jurong shipyard of Singapore in 1979, Bima was designed by Mining and Transport Engineering, a subsidiary of IHC Holland. Billiton Marine used the dredge for tin production at Pulau Tujuh in Indonesia (Dieperink, 1978) before it was laid up in mid-1985. Bima underwent a nine-week refit before departing Singapore on June 4,1986, with 800-t (880-st ) of deck cargo. It was dry-towed for 32 days to Alaska. A slower, less expensive, wet-tow at the authorized 5.5 kmthr (3 knots/hour) would have delayed the dredge's arrival in Alaska untl almost the onset of winter. The 13,000-km (8,100-mile) voyage was made on the deck of Smit Lloyd's "Giant-4" submersible barge towed by its 7.8- MW (10,500-hp) tugboat. The first season's dredging revealed several major shortcomings in Bima. Further repairs and modifications were undertaken at Tacoma, WA. The dredge returned to Nome for the June start of the 1987 summer dredging season. The refitted Bima worked offshore at Nome from 1987 to 1990. It produced 3.67 t (118,078 oz) of gold at an average recovered grade of 824 mg/m3 (0.0204 oz/cu yd). In 1991, the dredge was dismantled and sold.

Jan 1, 1997

By W. R. Reed, D. E. Pollock, T. W. Beck, J. A. Organiscak, J. D. Potts

"In underground continuous mining operations, ventilation, water sprays, and machine-mounted flooded bed scrubbers are the primary means of controlling respirable dust exposures at the working face. Changes in mining arrangements, such as, face ventilation configuration, orientation of crosscuts mined in relation to the section ventilation, and equipment operator positioning, can impact the ability of dust controls to reduce occupational respirable dust exposures. This study reports and analyzes dust concentrations measured by the Office of Mine Safety and Health Research for both remote-controlled continuous mining machine operators and haulage operators at ten U.S. underground mines. Results of these respirable dust surveys show that continuous miner exposures varied little based on depth of cut, but are significantly affected by ventilation configuration. Haulage operators experienced elevated concentrations in blowing face ventilation. The type of cut influenced exposures, with elevated exposures observed for both continuous miner operators and haulage operators when working in crosscuts driven into, or counter to, the section airflow. Individual cuts are highlighted to demonstrate instances of minimal and excessive dust exposure attributable to particular mining configurations. These findings form the basis of recommendations for lowering face worker respirable dust exposures when performing a variety of continuous mining cuts.INTRODUCTION Underground continuous coal mining operations may encounter a wide range of conditions and arrangements during production and development activities. These activities typically produce respirable coal mine dust, putting operators of continuous mining machines and coal haulers at risk for elevated exposures. In order to comply with federal regulations limiting respirable dust exposures for the duration of a working shift, mine operators typically implement ventilation, water sprays, and machine-mounted flooded-bed dust collectors (scrubbers) to dilute and control mine dusts during coal cutting. Nevertheless, changes in operational conditions can limit the ability of these controls to effectively reduce dust exposures. Some examples of conditions that can change during the course of mining include face ventilation configuration, orientation of crosscuts mined in relation to the section ventilation, and operator positioning. Because these arrangements are largely under the control of mine operators, any insight into associated exposures may inform future plans and behaviors, reducing occupational exposures to respirable dust. The objective of this OMSHR study is to evaluate respirable dust exposures associated with a range of continuous mining arrangements by comparing occupational dust concentrations measured during a series of field surveys. These comparisons consider face ventilation configurations, depths of cut, and crosscut mining practices."

Jan 1, 2015

By Werner Burger

The Hallandsås project with a long history, first started in 1991, is well known in the tunneling community. In the past it has been stopped twice for technical and environmental reasons. The third attempt started in 2004 using a dual mode rock TBM. The heterogeneous highly fractured and abrasive rock mass as well as large areas of water bearing zones present most difficult subsurface conditions. The tunneling concept is based on the use of watertight segmental lining and a TBM able to operate in open mode, possibilities for extensive pre excavation grouting and high pressure closed mode operation up to 13 bar to cover exceptional conditions.

By Zhe Liu, Liping Xiao, Jichi Bai, Xuefei Luan

"In order to study the removal efficiency of Cu2+ from acid mine drainage by prepared bentonite-steel slag composite particles, adsorption experiment was carried out. The composite particles were characterized by X-ray Diffraction analysis technique (XRD), Scanning Electron Microscopy (SEM) and Fourier Transform Infrared spectrometer (FTIR). The results show that: the composite particles can release alkali to neutralize the acid of acid mine drainage; the adsorption and chemical precipitation of Cu2+ occurred in the whole reaction process; the removal amount of composite particles on Cu2+ was 9.88 mg/g when the reaction reached equilibrium; the FTIR spectra revealed the existence of surface complexation; the SEM micrographs suggested that the composite particles would continue to adsorb and coagulate Cu2+ after the composite particles surface adsorbing Cu2+ and forming precipitate, namely, there was synergistic reaction of adsorption and coagulation; the XRD patterns further showed the existence of cation exchange and revealed that the states of Cu2+ in the surface of the composite particles was Cu-Si-O mineral phase and CuO(Cu(OH)2) polymerization precipitation. The bentonite-steel slag composite particles which can play a role of adsorption-coagulation synergism are excellent multifunctional green environmental mineral materials to treat acid mine drainage containing heavy metal ions.Introduction It is reported (Zuo and He 2013) that with the rapid development of industry, the world demand for mineral resources is increasing, while the problem of mine environmental pollution is becoming more and more serious due to the large amount of mining. The pollution of mine wastewater has become a global problem, in which acid mine drainage (AMD) is one of the most serious waste water. It is also reported (Cong and Zhao 2003) that acid mine drainage containing high concentrations of heavy metals and having low pH value, causing serious negative influence to the mining production and ecological environment. Acid mine drainage is one of the most serious environmental pollution to the mining industry. In recent years, it has been widely concerned by scholars at home and abroad."

Jan 1, 2017

By Robert C. Meaders

In this paper, autogenous grinding is defined as the combined crushing and grinder of a run-of-mine ore or the product from a primary crusher, in a single stage grinding mill. This is in contrast to pebble milling where pebbles are substituted for steel balls to grind a ball mill size feed. The autogenous mill to compete in efficiency with normal methods of crushing and grinding must not use greater power, must use less labor and steel, and must produce an equivalent product.

Jan 1, 1963